[PATCH v13 00/15] phy: Add support for Lynx 10G SerDes

[PATCH v13 00/15] phy: Add support for Lynx 10G SerDes

[Sean Anderson]

This adds support for the Lynx 10G SerDes found on the QorIQ T-series
and Layerscape series. Due to limited time and hardware, only support
for the LS1046ARDB and LS1088ARDB is added in this initial series.

This series is ready for review by the phy maintainers. I have addressed
all known feedback and there are no outstanding issues.

There are several stand-alone commits in this series. Please feel free
to pick them as appropriate. In particular, commits 1, 3, 4, 12, 13, and
14 are all good candidates for picking.

Major reconfiguration of baud rate (e.g. 1G->10G) does not work. From my
testing, SerDes register settings appear identical. The issue appears to
be between the PCS and the MAC. The link itself comes up at both ends,
and a mac loopback succeeds. However, a PCS loopback results in dropped
packets. Perhaps there is some undocumented register in the PCS?

I suspect this driver is around 95% complete, but I don't have the
documentation to make it work completely. At the very least it is useful
for two cases:

- Although this is untested, it should support 2.5G SGMII as well as
  1000BASE-KX. The latter needs MAC and PCS support, but the former
  should work out of the box.
- It allows for clock configurations not supported by the RCW. This is
  very useful if you want to use e.g. SRDS_PRTCL_S1=0x3333 and =0x1133
  on the same board. This is because the former setting will use PLL1
  as the 1G reference, but the latter will use PLL1 as the 10G
  reference. Because we can reconfigure the PLLs, it is possible to
  always use PLL1 as the 1G reference.

Changes in v13:
- Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)
- Split interrupt changes off from serdes support
- Split off SFP addition from serdes support

Changes in v12:
- Put compatible first
- Keep gpio-controller to one line
- Add little-endian property
- Alphabetize compatibles
- Remove some comments
- Remove some examples with insufficient novelty

Changes in v11:
- Keep empty (or almost-empty) properties on a single line
- Don't use | unnecessarily
- Use gpio as the node name for examples
- Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml

Changes in v10:
- Convert gpio-mmio to yaml
- Add compatible for QIXIS
- Remove unnecessary inclusion of clk.h
- Don't gate clocks in compatibility mode
- Fix debugging print with incorrect error variable
- Move serdes bindings to SoC dtsi
- Add support for all (ethernet) serdes modes
- Refer to "nodes" instead of "bindings"
- Move compatible/reg first

Changes in v9:
- Add fsl,unused-lanes-reserved to allow for a gradual transition
  between firmware and Linux control of the SerDes
- Change phy-type back to fsl,type, as I was getting the error
    '#phy-cells' is a dependency of 'phy-type'
- Convert some u32s to unsigned long to match arguments
- Switch from round_rate to determine_rate
- Drop explicit reference to reference clock
- Use .parent_names when requesting parents
- Use devm_clk_hw_get_clk to pass clocks back to serdes
- Fix indentation
- Split off clock "driver" into its own patch to allow for better
  review.
- Add ability to defer lane initialization to phy_init. This allows
  for easier transitioning between firmware-managed serdes and Linux-
  managed serdes, as the consumer (such as dpaa2, which knows what the
  firmware is doing) has the last say on who gets control.
- Fix name of phy mode node
- Add fsl,unused-lanes-reserved to allow a gradual transition, depending
  on the mac link type.
- Remove unused clocks
- Fix some phy mode node names

Changes in v8:
- Remove unused variable from lynx_ls_mode_init
- Rename serdes phy handles to use _A, _B, etc. instead of _0, _1, etc.
  This should help remind readers that the numbering corresponds to the
  physical layout of the registers, and not the lane (pin) number.
- Prevent PCSs from probing as phys
- Rename serdes phy handles like the LS1046A
- Add SFP slot binding
- Fix incorrect lane ordering (it's backwards on the LS1088A just like it is in
  the LS1046A).
- Fix duplicated lane 2 (it should have been lane 3).
- Fix incorrectly-documented value for XFI1.
- Remove interrupt for aquantia phy. It never fired for whatever reason,
  preventing the link from coming up.
- Add GPIOs for QIXIS FPGA.
- Enable MAC1 PCS
- Remove si5341 binding

Changes in v7:
- Use double quotes everywhere in yaml
- Break out call order into generic documentation
- Refuse to switch "major" protocols
- Update Kconfig to reflect restrictions
- Remove set/clear of "pcs reset" bit, since it doesn't seem to fix
  anything.

Changes in v6:
- Bump PHY_TYPE_2500BASEX to 13, since PHY_TYPE_USXGMII was added in the
  meantime
- fsl,type -> phy-type
- frequence -> frequency
- Update MAINTAINERS to include new files
- Include bitfield.h and slab.h to allow compilation on non-arm64
  arches.
- Depend on COMMON_CLK and either layerscape/ppc
- XGI.9 -> XFI.9

Changes in v5:
- Update commit description
- Dual id header
- Remove references to PHY_INTERFACE_MODE_1000BASEKX to allow this
  series to be applied directly to linux/master.
- Add fsl,lynx-10g.h to MAINTAINERS

Changes in v4:
- Add 2500BASE-X and 10GBASE-R phy types
- Use subnodes to describe lane configuration, instead of describing
  PCCRs. This is the same style used by phy-cadence-sierra et al.
- Add ids for Lynx 10g PLLs
- Rework all debug statements to remove use of __func__. Additional
  information has been provided as necessary.
- Consider alternative parent rates in round_rate and not in set_rate.
  Trying to modify out parent's rate in set_rate will deadlock.
- Explicitly perform a stop/reset sequence in set_rate. This way we
  always ensure that the PLL is properly stopped.
- Set the power-down bit when disabling the PLL. We can do this now that
  enable/disable aren't abused during the set rate sequence.
- Fix typos in QSGMII_OFFSET and XFI_OFFSET
- Rename LNmTECR0_TEQ_TYPE_PRE to LNmTECR0_TEQ_TYPE_POST to better
  reflect its function (adding post-cursor equalization).
- Use of_clk_hw_onecell_get instead of a custom function.
- Return struct clks from lynx_clks_init instead of embedding lynx_clk
  in lynx_priv.
- Rework PCCR helper functions; T-series SoCs differ from Layerscape SoCs
  primarily in the layout and offset of the PCCRs. This will help bring a
  cleaner abstraction layer. The caps have been removed, since this handles the
  only current usage.
- Convert to use new binding format. As a result of this, we no longer need to
  have protocols for PCIe or SATA. Additionally, modes now live in lynx_group
  instead of lynx_priv.
- Remove teq from lynx_proto_params, since it can be determined from
  preq_ratio/postq_ratio.
- Fix an early return from lynx_set_mode not releasing serdes->lock.
- Rename lynx_priv.conf to .cfg, since I kept mistyping it.

Changes in v3:
- Manually expand yaml references
- Add mode configuration to device tree
- Rename remaining references to QorIQ SerDes to Lynx 10G
- Fix PLL enable sequence by waiting for our reset request to be cleared
  before continuing. Do the same for the lock, even though it isn't as
  critical. Because we will delay for 1.5ms on average, use prepare
  instead of enable so we can sleep.
- Document the status of each protocol
- Fix offset of several bitfields in RECR0
- Take into account PLLRST_B, SDRST_B, and SDEN when considering whether
  a PLL is "enabled."
- Only power off unused lanes.
- Split mode lane mask into first/last lane (like group)
- Read modes from device tree
- Use caps to determine whether KX/KR are supported
- Move modes to lynx_priv
- Ensure that the protocol controller is not already in-use when we try
  to configure a new mode. This should only occur if the device tree is
  misconfigured (e.g. when QSGMII is selected on two lanes but there is
  only one QSGMII controller).
- Split PLL drivers off into their own file
- Add clock for "ext_dly" instead of writing the bit directly (and
  racing with any clock code).
- Use kasprintf instead of open-coding the snprintf dance
- Support 1000BASE-KX in lynx_lookup_proto. This still requires PCS
  support, so nothing is truly "enabled" yet.
- Describe modes in device tree
- ls1088a: Add serdes bindings

Changes in v2:
- Rename to fsl,lynx-10g.yaml
- Refer to the device in the documentation, rather than the binding
- Move compatible first
- Document phy cells in the description
- Allow a value of 1 for phy-cells. This allows for compatibility with
  the similar (but according to Ioana Ciornei different enough) lynx-28g
  binding.
- Remove minItems
- Use list for clock-names
- Fix example binding having too many cells in regs
- Add #clock-cells. This will allow using assigned-clocks* to configure
  the PLLs.
- Document the structure of the compatible strings
- Rename driver to Lynx 10G (etc.)
- Fix not clearing group->pll after disabling it
- Support 1 and 2 phy-cells
- Power off lanes during probe
- Clear SGMIIaCR1_PCS_EN during probe
- Rename LYNX_PROTO_UNKNOWN to LYNX_PROTO_NONE
- Handle 1000BASE-KX in lynx_proto_mode_prep
- Use one phy cell for SerDes1, since no lanes can be grouped
- Disable SerDes by default to prevent breaking boards inadvertently.

Sean Anderson (15):
  dt-bindings: phy: Add 2500BASE-X and 10GBASE-R
  dt-bindings: phy: Add Lynx 10G phy binding
  dt-bindings: Convert gpio-mmio to yaml
  dt-bindings: gpio-mmio: Add compatible for QIXIS
  dt-bindings: clock: Add ids for Lynx 10g PLLs
  clk: Add Lynx 10G SerDes PLL driver
  phy: fsl: Add Lynx 10G SerDes driver
  phy: lynx10g: Enable by default on Layerscape
  arm64: dts: ls1046a: Add serdes nodes
  arm64: dts: ls1046ardb: Add serdes descriptions
  arm64: dts: ls1088a: Add serdes nodes
  arm64: dts: ls1088a: Prevent PCSs from probing as phys
  arm64: dts: ls1088ardb: Remove aquantia interrupt
  arm64: dts: ls1088ardb: Add SFP cage
  arm64: dts: ls1088ardb: Add serdes descriptions

 ...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} |   16 +-
 .../devicetree/bindings/gpio/gpio-mmio.yaml   |  123 ++
 .../bindings/gpio/ni,169445-nand-gpio.txt     |   38 -
 .../devicetree/bindings/gpio/wd,mbl-gpio.txt  |   38 -
 .../mfd/brcm,bcm6318-gpio-sysctl.yaml         |    4 +-
 .../mfd/brcm,bcm63268-gpio-sysctl.yaml        |    4 +-
 .../mfd/brcm,bcm6328-gpio-sysctl.yaml         |    4 +-
 .../mfd/brcm,bcm6358-gpio-sysctl.yaml         |    4 +-
 .../mfd/brcm,bcm6362-gpio-sysctl.yaml         |    4 +-
 .../mfd/brcm,bcm6368-gpio-sysctl.yaml         |    4 +-
 .../devicetree/bindings/phy/fsl,lynx-10g.yaml |  248 ++++
 Documentation/driver-api/phy/index.rst        |    1 +
 Documentation/driver-api/phy/lynx_10g.rst     |   58 +
 MAINTAINERS                                   |    9 +
 .../boot/dts/freescale/fsl-ls1046a-rdb.dts    |   26 +
 .../arm64/boot/dts/freescale/fsl-ls1046a.dtsi |  111 ++
 .../boot/dts/freescale/fsl-ls1088a-rdb.dts    |   82 +-
 .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi |  156 ++-
 drivers/clk/Makefile                          |    1 +
 drivers/clk/clk-fsl-lynx-10g.c                |  510 +++++++
 drivers/phy/freescale/Kconfig                 |   23 +
 drivers/phy/freescale/Makefile                |    1 +
 drivers/phy/freescale/phy-fsl-lynx-10g.c      | 1224 +++++++++++++++++
 include/dt-bindings/clock/fsl,lynx-10g.h      |   14 +
 include/dt-bindings/phy/phy.h                 |    2 +
 include/linux/phy/lynx-10g.h                  |   16 +
 26 files changed, 2606 insertions(+), 115 deletions(-)
 rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (78%)
 create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
 delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
 delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
 create mode 100644 Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml
 create mode 100644 Documentation/driver-api/phy/lynx_10g.rst
 create mode 100644 drivers/clk/clk-fsl-lynx-10g.c
 create mode 100644 drivers/phy/freescale/phy-fsl-lynx-10g.c
 create mode 100644 include/dt-bindings/clock/fsl,lynx-10g.h
 create mode 100644 include/linux/phy/lynx-10g.h

-- 
2.35.1.1320.gc452695387.dirty

[PATCH v13 03/15] dt-bindings: Convert gpio-mmio to yaml

[Sean Anderson]

This is a generic binding for simple MMIO GPIO controllers. Although we
have a single driver for these controllers, they were previously spread
over several files. Consolidate them. The register descriptions are
adapted from the comments in the source. There is no set order for the
registers, and some registers may be omitted. Because of this, reg-names
is mandatory, and no order is specified.

Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
has moved.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
Linus or Bartosz, feel free to pick this up as the rest of this series
may not be merged any time soon.

Changes in v13:
- Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)

Changes in v12:
- Put compatible first
- Keep gpio-controller to one line
- Add little-endian property
- Alphabetize compatibles
- Remove some comments
- Remove some examples with insufficient novelty

Changes in v11:
- Keep empty (or almost-empty) properties on a single line
- Don't use | unnecessarily
- Use gpio as the node name for examples
- Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml

Changes in v10:
- New

 ...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} |  16 +--
 .../devicetree/bindings/gpio/gpio-mmio.yaml   | 117 ++++++++++++++++++
 .../bindings/gpio/ni,169445-nand-gpio.txt     |  38 ------
 .../devicetree/bindings/gpio/wd,mbl-gpio.txt  |  38 ------
 .../mfd/brcm,bcm6318-gpio-sysctl.yaml         |   4 +-
 .../mfd/brcm,bcm63268-gpio-sysctl.yaml        |   4 +-
 .../mfd/brcm,bcm6328-gpio-sysctl.yaml         |   4 +-
 .../mfd/brcm,bcm6358-gpio-sysctl.yaml         |   4 +-
 .../mfd/brcm,bcm6362-gpio-sysctl.yaml         |   4 +-
 .../mfd/brcm,bcm6368-gpio-sysctl.yaml         |   4 +-
 10 files changed, 130 insertions(+), 103 deletions(-)
 rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (78%)
 create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
 delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
 delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt

diff --git a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
similarity index 78%
rename from Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml
rename to Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
index 4d69f79df859..e11f4af49c52 100644
--- a/Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml
+++ b/Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml
@@ -4,7 +4,7 @@
 $id: http://devicetree.org/schemas/gpio/brcm,bcm6345-gpio.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
-title: Broadcom BCM6345 GPIO controller
+title: Broadcom BCM63xx GPIO controller
 
 maintainers:
   - Álvaro Fernández Rojas <noltari@gmail.com>
@@ -18,8 +18,6 @@ description: |+
 
   BCM6338 have 8-bit data and dirout registers, where GPIO state can be read
   and/or written, and the direction changed from input to output.
-  BCM6345 have 16-bit data and dirout registers, where GPIO state can be read
-  and/or written, and the direction changed from input to output.
   BCM6318, BCM6328, BCM6358, BCM6362, BCM6368 and BCM63268 have 32-bit data
   and dirout registers, where GPIO state can be read and/or written, and the
   direction changed from input to output.
@@ -29,7 +27,6 @@ properties:
     enum:
       - brcm,bcm6318-gpio
       - brcm,bcm6328-gpio
-      - brcm,bcm6345-gpio
       - brcm,bcm6358-gpio
       - brcm,bcm6362-gpio
       - brcm,bcm6368-gpio
@@ -63,17 +60,6 @@ required:
 additionalProperties: false
 
 examples:
-  - |
-    gpio@fffe0406 {
-      compatible = "brcm,bcm6345-gpio";
-      reg-names = "dirout", "dat";
-      reg = <0xfffe0406 2>, <0xfffe040a 2>;
-      native-endian;
-
-      gpio-controller;
-      #gpio-cells = <2>;
-    };
-
   - |
     gpio@0 {
       compatible = "brcm,bcm63268-gpio";
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml b/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
new file mode 100644
index 000000000000..b394e058256e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/gpio-mmio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic MMIO GPIO
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+  - Bartosz Golaszewski <brgl@bgdev.pl>
+
+description:
+  Some simple GPIO controllers may consist of a single data register or a pair
+  of set/clear-bit registers. Such controllers are common for glue logic in
+  FPGAs or ASICs. Commonly, these controllers are accessed over memory-mapped
+  NAND-style parallel busses.
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm6345-gpio
+      - ni,169445-nand-gpio
+      - wd,mbl-gpio # Western Digital MyBook Live memory-mapped GPIO controller
+
+  big-endian: true
+
+  '#gpio-cells':
+    const: 2
+
+  gpio-controller: true
+
+  little-endian: true
+
+  reg:
+    minItems: 1
+    description:
+      A list of registers in the controller. The width of each register is
+      determined by its size. All registers must have the same width. The number
+      of GPIOs is set by the width, with bit 0 corresponding to GPIO 0.
+    items:
+      - description:
+          Register to READ the value of the GPIO lines. If GPIO line is high,
+          the bit will be set. If the GPIO line is low, the bit will be cleared.
+          This register may also be used to drive GPIOs if the SET register is
+          omitted.
+      - description:
+          Register to SET the value of the GPIO lines. Setting a bit in this
+          register will drive the GPIO line high.
+      - description:
+          Register to CLEAR the value of the GPIO lines. Setting a bit in this
+          register will drive the GPIO line low. If this register is omitted,
+          the SET register will be used to clear the GPIO lines as well, by
+          actively writing the line with 0.
+      - description:
+          Register to set the line as OUTPUT. Setting a bit in this register
+          will turn that line into an output line. Conversely, clearing a bit
+          will turn that line into an input.
+      - description:
+          Register to set this line as INPUT. Setting a bit in this register
+          will turn that line into an input line. Conversely, clearing a bit
+          will turn that line into an output.
+
+  reg-names:
+    minItems: 1
+    maxItems: 5
+    items:
+      enum:
+        - dat
+        - set
+        - clr
+        - dirout
+        - dirin
+
+  native-endian: true
+
+  no-output:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      If this property is present, the controller cannot drive the GPIO lines.
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - '#gpio-cells'
+  - gpio-controller
+
+additionalProperties: false
+
+examples:
+  - |
+    gpio@1f300010 {
+      compatible = "ni,169445-nand-gpio";
+      reg = <0x1f300010 0x4>;
+      reg-names = "dat";
+      gpio-controller;
+      #gpio-cells = <2>;
+    };
+
+    gpio@e0100000 {
+      compatible = "wd,mbl-gpio";
+      reg-names = "dat";
+      reg = <0xe0100000 0x1>;
+      #gpio-cells = <2>;
+      gpio-controller;
+      no-output;
+    };
+
+    gpio@fffe0406 {
+      compatible = "brcm,bcm6345-gpio";
+      reg-names = "dirout", "dat";
+      reg = <0xfffe0406 2>, <0xfffe040a 2>;
+      native-endian;
+      gpio-controller;
+      #gpio-cells = <2>;
+    };
diff --git a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt b/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
deleted file mode 100644
index ca2f8c745a27..000000000000
--- a/Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-Bindings for the National Instruments 169445 GPIO NAND controller
-
-The 169445 GPIO NAND controller has two memory mapped GPIO registers, one
-for input (the ready signal) and one for output (control signals).  It is
-intended to be used with the GPIO NAND driver.
-
-Required properties:
-	- compatible: should be "ni,169445-nand-gpio"
-	- reg-names: must contain
-		"dat" - data register
-	- reg: address + size pairs describing the GPIO register sets;
-		order must correspond with the order of entries in reg-names
-	- #gpio-cells: must be set to 2. The first cell is the pin number and
-			the second cell is used to specify the gpio polarity:
-			0 = active high
-			1 = active low
-	- gpio-controller: Marks the device node as a gpio controller.
-
-Optional properties:
-	- no-output: disables driving output on the pins
-
-Examples:
-	gpio1: nand-gpio-out@1f300010 {
-		compatible = "ni,169445-nand-gpio";
-		reg = <0x1f300010 0x4>;
-		reg-names = "dat";
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	gpio2: nand-gpio-in@1f300014 {
-		compatible = "ni,169445-nand-gpio";
-		reg = <0x1f300014 0x4>;
-		reg-names = "dat";
-		gpio-controller;
-		#gpio-cells = <2>;
-		no-output;
-	};
diff --git a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt b/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
deleted file mode 100644
index 038c3a6a1f4d..000000000000
--- a/Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-Bindings for the Western Digital's MyBook Live memory-mapped GPIO controllers.
-
-The Western Digital MyBook Live has two memory-mapped GPIO controllers.
-Both GPIO controller only have a single 8-bit data register, where GPIO
-state can be read and/or written.
-
-Required properties:
-	- compatible: should be "wd,mbl-gpio"
-	- reg-names: must contain
-		"dat" - data register
-	- reg: address + size pairs describing the GPIO register sets;
-		order must correspond with the order of entries in reg-names
-	- #gpio-cells: must be set to 2. The first cell is the pin number and
-			the second cell is used to specify the gpio polarity:
-			0 = active high
-			1 = active low
-	- gpio-controller: Marks the device node as a gpio controller.
-
-Optional properties:
-	- no-output: GPIOs are read-only.
-
-Examples:
-	gpio0: gpio0@e0000000 {
-		compatible = "wd,mbl-gpio";
-		reg-names = "dat";
-		reg = <0xe0000000 0x1>;
-		#gpio-cells = <2>;
-		gpio-controller;
-	};
-
-	gpio1: gpio1@e0100000 {
-		compatible = "wd,mbl-gpio";
-		reg-names = "dat";
-		reg = <0xe0100000 0x1>;
-		#gpio-cells = <2>;
-		gpio-controller;
-		no-output;
-	};
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
index 148f1da47603..9f9a14af875e 100644
--- a/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
@@ -35,11 +35,11 @@ patternProperties:
   "^gpio@[0-9a-f]+$":
     # Child node
     type: object
-    $ref: "../gpio/brcm,bcm6345-gpio.yaml"
+    $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
     description:
       GPIO controller for the SoC GPIOs. This child node definition
       should follow the bindings specified in
-      Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml.
+      Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml.
 
   "^pinctrl@[0-9a-f]+$":
     # Child node
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml
index 7e582243ea76..803277dd2725 100644
--- a/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml
@@ -35,11 +35,11 @@ patternProperties:
   "^gpio@[0-9a-f]+$":
     # Child node
     type: object
-    $ref: "../gpio/brcm,bcm6345-gpio.yaml"
+    $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
     description:
       GPIO controller for the SoC GPIOs. This child node definition
       should follow the bindings specified in
-      Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml.
+      Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml.
 
   "^pinctrl@[0-9a-f]+$":
     # Child node
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml
index 2230848e11c3..b9a6856ce970 100644
--- a/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml
@@ -35,11 +35,11 @@ patternProperties:
   "^gpio@[0-9a-f]+$":
     # Child node
     type: object
-    $ref: "../gpio/brcm,bcm6345-gpio.yaml"
+    $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
     description:
       GPIO controller for the SoC GPIOs. This child node definition
       should follow the bindings specified in
-      Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml.
+      Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml.
 
   "^pinctrl@[0-9a-f]+$":
     # Child node
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml
index c06693b6f7aa..4651fe4dde07 100644
--- a/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml
@@ -35,11 +35,11 @@ patternProperties:
   "^gpio@[0-9a-f]+$":
     # Child node
     type: object
-    $ref: "../gpio/brcm,bcm6345-gpio.yaml"
+    $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
     description:
       GPIO controller for the SoC GPIOs. This child node definition
       should follow the bindings specified in
-      Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml.
+      Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml.
 
   "^pinctrl@[0-9a-f]+$":
     # Child node
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml
index c560bede0e37..0330b621fd38 100644
--- a/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml
@@ -35,11 +35,11 @@ patternProperties:
   "^gpio@[0-9a-f]+$":
     # Child node
     type: object
-    $ref: "../gpio/brcm,bcm6345-gpio.yaml"
+    $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
     description:
       GPIO controller for the SoC GPIOs. This child node definition
       should follow the bindings specified in
-      Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml.
+      Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml.
 
   "^pinctrl@[0-9a-f]+$":
     # Child node
diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml b/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml
index c534f5f2404e..82d3e4415bda 100644
--- a/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml
+++ b/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml
@@ -35,11 +35,11 @@ patternProperties:
   "^gpio@[0-9a-f]+$":
     # Child node
     type: object
-    $ref: "../gpio/brcm,bcm6345-gpio.yaml"
+    $ref: "../gpio/brcm,bcm63xx-gpio.yaml"
     description:
       GPIO controller for the SoC GPIOs. This child node definition
       should follow the bindings specified in
-      Documentation/devicetree/bindings/gpio/brcm,bcm6345-gpio.yaml.
+      Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml.
 
   "^pinctrl@[0-9a-f]+$":
     # Child node
-- 
2.35.1.1320.gc452695387.dirty

Re: [PATCH v13 03/15] dt-bindings: Convert gpio-mmio to yaml

[Rob Herring]

On Tue, 11 Apr 2023 14:43:00 -0400, Sean Anderson wrote:
> This is a generic binding for simple MMIO GPIO controllers. Although we
> have a single driver for these controllers, they were previously spread
> over several files. Consolidate them. The register descriptions are
> adapted from the comments in the source. There is no set order for the
> registers, and some registers may be omitted. Because of this, reg-names
> is mandatory, and no order is specified.
> 
> Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
> has moved.
> 
> Signed-off-by: Sean Anderson <sean.anderson@seco.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> Linus or Bartosz, feel free to pick this up as the rest of this series
> may not be merged any time soon.
> 
> Changes in v13:
> - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)
> 
> Changes in v12:
> - Put compatible first
> - Keep gpio-controller to one line
> - Add little-endian property
> - Alphabetize compatibles
> - Remove some comments
> - Remove some examples with insufficient novelty
> 
> Changes in v11:
> - Keep empty (or almost-empty) properties on a single line
> - Don't use | unnecessarily
> - Use gpio as the node name for examples
> - Rename brcm,bcm6345-gpio.yaml to brcm,bcm63xx-gpio.yaml
> 
> Changes in v10:
> - New
> 
>  ...m6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} |  16 +--
>  .../devicetree/bindings/gpio/gpio-mmio.yaml   | 117 ++++++++++++++++++
>  .../bindings/gpio/ni,169445-nand-gpio.txt     |  38 ------
>  .../devicetree/bindings/gpio/wd,mbl-gpio.txt  |  38 ------
>  .../mfd/brcm,bcm6318-gpio-sysctl.yaml         |   4 +-
>  .../mfd/brcm,bcm63268-gpio-sysctl.yaml        |   4 +-
>  .../mfd/brcm,bcm6328-gpio-sysctl.yaml         |   4 +-
>  .../mfd/brcm,bcm6358-gpio-sysctl.yaml         |   4 +-
>  .../mfd/brcm,bcm6362-gpio-sysctl.yaml         |   4 +-
>  .../mfd/brcm,bcm6368-gpio-sysctl.yaml         |   4 +-
>  10 files changed, 130 insertions(+), 103 deletions(-)
>  rename Documentation/devicetree/bindings/gpio/{brcm,bcm6345-gpio.yaml => brcm,bcm63xx-gpio.yaml} (78%)
>  create mode 100644 Documentation/devicetree/bindings/gpio/gpio-mmio.yaml
>  delete mode 100644 Documentation/devicetree/bindings/gpio/ni,169445-nand-gpio.txt
>  delete mode 100644 Documentation/devicetree/bindings/gpio/wd,mbl-gpio.txt
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
./Documentation/devicetree/bindings/gpio/brcm,bcm63xx-gpio.yaml: $id: relative path/filename doesn't match actual path or filename
	expected: http://devicetree.org/schemas/gpio/brcm,bcm63xx-gpio.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6318-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 50]], '#gpio-cells': [[2]]}
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6318-gpio-sysctl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.example.dtb: syscon@100000c0: gpio@0: False schema does not allow {'compatible': ['brcm,bcm63268-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 52]], '#gpio-cells': [[2]]}
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm63268-gpio-sysctl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6362-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 48]], '#gpio-cells': [[2]]}
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6362-gpio-sysctl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6328-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 32]], '#gpio-cells': [[2]]}
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6328-gpio-sysctl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.example.dtb: syscon@fffe0080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6358-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 40]], '#gpio-cells': [[2]]}
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6358-gpio-sysctl.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.example.dtb: syscon@10000080: gpio@0: False schema does not allow {'compatible': ['brcm,bcm6368-gpio'], 'reg-names': ['dirout', 'dat'], 'reg': [[0, 8], [8, 8]], 'gpio-controller': True, 'gpio-ranges': [[1, 0, 0, 38]], '#gpio-cells': [[2]]}
	From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mfd/brcm,bcm6368-gpio-sysctl.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230411184313.3679145-4-sean.anderson@seco.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v13 03/15] dt-bindings: Convert gpio-mmio to yaml

[Krzysztof Kozlowski]

On 11/04/2023 20:43, Sean Anderson wrote:
> This is a generic binding for simple MMIO GPIO controllers. Although we
> have a single driver for these controllers, they were previously spread
> over several files. Consolidate them. The register descriptions are
> adapted from the comments in the source. There is no set order for the
> registers, and some registers may be omitted. Because of this, reg-names
> is mandatory, and no order is specified.
> 
> Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
> has moved.
> 
> Signed-off-by: Sean Anderson <sean.anderson@seco.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> Linus or Bartosz, feel free to pick this up as the rest of this series
> may not be merged any time soon.
> 
> Changes in v13:
> - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)

You got some of the same errors as last time.

Test your patches before sending.

Best regards,
Krzysztof

Re: [PATCH v13 03/15] dt-bindings: Convert gpio-mmio to yaml

[Sean Anderson]

On 4/12/23 04:04, Krzysztof Kozlowski wrote:
> On 11/04/2023 20:43, Sean Anderson wrote:
>> This is a generic binding for simple MMIO GPIO controllers. Although we
>> have a single driver for these controllers, they were previously spread
>> over several files. Consolidate them. The register descriptions are
>> adapted from the comments in the source. There is no set order for the
>> registers, and some registers may be omitted. Because of this, reg-names
>> is mandatory, and no order is specified.
>> 
>> Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
>> has moved.
>> 
>> Signed-off-by: Sean Anderson <sean.anderson@seco.com>
>> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
>> ---
>> Linus or Bartosz, feel free to pick this up as the rest of this series
>> may not be merged any time soon.
>> 
>> Changes in v13:
>> - Fix references to brcm,bcm63xx-gpio.yaml (neé brcm,bcm6345-gpio)
> 
> You got some of the same errors as last time.

These are different errors.

> Test your patches before sending.

I typically run dt_bindings_check with DT_SCHEMA_FILES=... because
running the whole thing takes longer than compiling a kernel from
scratch. It seems I neglected to run it on the affected schemas.

--Sean