[PATCH v2 14/14] arm64: dts: qcom: sc8280xp-x13s: enable pm8008 camera pmic

[Johan Hovold <johan+linaro@kernel.org>]

Enable the PM8008 PMIC which is used to power the camera sensors.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
---
 .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 123 ++++++++++++++++++
 1 file changed, 123 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
index 98c1b75513be..93a44f803e8d 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -295,6 +295,27 @@ linux,cma {
 	};
 
 	thermal-zones {
+		pm8008-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8008>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
 		skin-temp-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
@@ -669,6 +690,85 @@ touchscreen@10 {
 	};
 };
 
+&i2c11 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c11_default>;
+
+	status = "okay";
+
+	pm8008: pmic@c {
+		compatible = "qcom,pm8008";
+		reg = <0xc>;
+
+		interrupts-extended = <&tlmm 41 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+
+		vdd-l1-l2-supply = <&vreg_s11b>;
+		vdd-l3-l4-supply = <&vreg_bob>;
+		vdd-l5-supply = <&vreg_bob>;
+		vdd-l6-supply = <&vreg_bob>;
+		vdd-l7-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm8008_default>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&pm8008 0 0 2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		#thermal-sensor-cells = <0>;
+
+		regulators {
+			vreg_l1q: ldo1 {
+				regulator-name = "vreg_l1q";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l2q: ldo2 {
+				regulator-name = "vreg_l2q";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l3q: ldo3 {
+				regulator-name = "vreg_l3q";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vreg_l4q: ldo4 {
+				regulator-name = "vreg_l4q";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vreg_l5q: ldo5 {
+				regulator-name = "vreg_l5q";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vreg_l6q: ldo6 {
+				regulator-name = "vreg_l6q";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vreg_l7q: ldo7 {
+				regulator-name = "vreg_l7q";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+		};
+	};
+};
+
 &i2c21 {
 	clock-frequency = <400000>;
 
@@ -1367,6 +1467,13 @@ i2c4_default: i2c4-default-state {
 		bias-disable;
 	};
 
+	i2c11_default: i2c11-default-state {
+		pins = "gpio18", "gpio19";
+		function = "qup11";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
 	i2c21_default: i2c21-default-state {
 		pins = "gpio81", "gpio82";
 		function = "qup21";
@@ -1470,6 +1577,22 @@ wake-n-pins {
 		};
 	};
 
+	pm8008_default: pm8008-default-state {
+		int-pins {
+			pins = "gpio41";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		reset-n-pins {
+			pins = "gpio42";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
 	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
 		perst-n-pins {
 			pins = "gpio178";
-- 
2.44.1