* [PATCH v11 2/8] platform: cznic: Add preliminary support for Turris Omnia MCU
2024-06-05 16:18 [PATCH v11 0/8] Turris Omnia MCU driver Marek Behún
@ 2024-06-05 16:18 ` Marek Behún
2024-06-05 18:04 ` Andy Shevchenko
2024-06-05 16:18 ` [PATCH v11 3/8] platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs Marek Behún
2024-06-05 19:05 ` [PATCH v11 0/8] Turris Omnia MCU driver Andy Shevchenko
2 siblings, 1 reply; 8+ messages in thread
From: Marek Behún @ 2024-06-05 16:18 UTC (permalink / raw)
To: Gregory CLEMENT, Arnd Bergmann, soc, arm, Andy Shevchenko,
Hans de Goede, Ilpo Järvinen, Linus Walleij,
Bartosz Golaszewski, linux-gpio, Alessandro Zummo,
Alexandre Belloni, linux-rtc, Wim Van Sebroeck, Guenter Roeck,
linux-watchdog
Cc: Marek Behún
Add the basic skeleton for a new platform driver for the microcontroller
found on the Turris Omnia board.
Signed-off-by: Marek Behún <kabel@kernel.org>
---
.../sysfs-bus-i2c-devices-turris-omnia-mcu | 81 ++++
MAINTAINERS | 3 +
drivers/platform/Kconfig | 2 +
drivers/platform/Makefile | 1 +
drivers/platform/cznic/Kconfig | 25 ++
drivers/platform/cznic/Makefile | 4 +
.../platform/cznic/turris-omnia-mcu-base.c | 393 ++++++++++++++++++
drivers/platform/cznic/turris-omnia-mcu.h | 74 ++++
include/linux/turris-omnia-mcu-interface.h | 249 +++++++++++
9 files changed, 832 insertions(+)
create mode 100644 Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
create mode 100644 drivers/platform/cznic/Kconfig
create mode 100644 drivers/platform/cznic/Makefile
create mode 100644 drivers/platform/cznic/turris-omnia-mcu-base.c
create mode 100644 drivers/platform/cznic/turris-omnia-mcu.h
create mode 100644 include/linux/turris-omnia-mcu-interface.h
diff --git a/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu b/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
new file mode 100644
index 000000000000..9bc5aad00de0
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
@@ -0,0 +1,81 @@
+What: /sys/bus/i2c/devices/<mcu_device>/board_revision
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains board revision number.
+
+ Only available if board information is burned in the MCU (older
+ revisions have board information burned in the ATSHA204-A chip).
+
+ Format: %u.
+
+What: /sys/bus/i2c/devices/<mcu_device>/first_mac_address
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains device first MAC address. Each Turris Omnia is
+ allocated 3 MAC addresses. The two additional addresses are
+ computed from the first one by incrementing it.
+
+ Only available if board information is burned in the MCU (older
+ revisions have board information burned in the ATSHA204-A chip).
+
+ Format: %pM.
+
+What: /sys/bus/i2c/devices/<mcu_device>/fw_features
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Newer versions of the microcontroller firmware report the
+ features they support. These can be read from this file. If the
+ MCU firmware is too old, this file reads 0x0.
+
+ Format: 0x%x.
+
+What: /sys/bus/i2c/devices/<mcu_device>/fw_version_hash_application
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains the version hash (commit hash) of the application
+ part of the microcontroller firmware.
+
+ Format: %s.
+
+What: /sys/bus/i2c/devices/<mcu_device>/fw_version_hash_bootloader
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains the version hash (commit hash) of the bootloader
+ part of the microcontroller firmware.
+
+ Format: %s.
+
+What: /sys/bus/i2c/devices/<mcu_device>/mcu_type
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains the microcontroller type (STM32, GD32, MKL).
+
+ Format: %s.
+
+What: /sys/bus/i2c/devices/<mcu_device>/reset_selector
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains the selected factory reset level, determined by
+ how long the rear reset button was held by the user during board
+ reset.
+
+ Format: %i.
+
+What: /sys/bus/i2c/devices/<mcu_device>/serial_number
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RO) Contains the 64-bit board serial number in hexadecimal
+ format.
+
+ Only available if board information is burned in the MCU (older
+ revisions have board information burned in the ATSHA204-A chip).
+
+ Format: %016X.
diff --git a/MAINTAINERS b/MAINTAINERS
index ee8b6dcd8f53..9f6dca4627c2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2207,6 +2207,7 @@ M: Marek Behún <kabel@kernel.org>
S: Maintained
W: https://www.turris.cz/
F: Documentation/ABI/testing/debugfs-moxtet
+F: Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
F: Documentation/ABI/testing/sysfs-bus-moxtet-devices
F: Documentation/ABI/testing/sysfs-firmware-turris-mox-rwtm
F: Documentation/devicetree/bindings/bus/moxtet.txt
@@ -2220,10 +2221,12 @@ F: drivers/firmware/turris-mox-rwtm.c
F: drivers/gpio/gpio-moxtet.c
F: drivers/leds/leds-turris-omnia.c
F: drivers/mailbox/armada-37xx-rwtm-mailbox.c
+F: drivers/platform/cznic/
F: drivers/watchdog/armada_37xx_wdt.c
F: include/dt-bindings/bus/moxtet.h
F: include/linux/armada-37xx-rwtm-mailbox.h
F: include/linux/moxtet.h
+F: include/linux/turris-omnia-mcu-interface.h
ARM/FARADAY FA526 PORT
M: Hans Ulli Kroll <ulli.kroll@googlemail.com>
diff --git a/drivers/platform/Kconfig b/drivers/platform/Kconfig
index 81a298517df2..960fd6a82450 100644
--- a/drivers/platform/Kconfig
+++ b/drivers/platform/Kconfig
@@ -7,6 +7,8 @@ source "drivers/platform/goldfish/Kconfig"
source "drivers/platform/chrome/Kconfig"
+source "drivers/platform/cznic/Kconfig"
+
source "drivers/platform/mellanox/Kconfig"
source "drivers/platform/olpc/Kconfig"
diff --git a/drivers/platform/Makefile b/drivers/platform/Makefile
index fbbe4f77aa5d..bf69cc8d7429 100644
--- a/drivers/platform/Makefile
+++ b/drivers/platform/Makefile
@@ -10,5 +10,6 @@ obj-$(CONFIG_MIPS) += mips/
obj-$(CONFIG_OLPC_EC) += olpc/
obj-$(CONFIG_GOLDFISH) += goldfish/
obj-$(CONFIG_CHROME_PLATFORMS) += chrome/
+obj-$(CONFIG_CZNIC_PLATFORMS) += cznic/
obj-$(CONFIG_SURFACE_PLATFORMS) += surface/
obj-$(CONFIG_ARM64) += arm64/
diff --git a/drivers/platform/cznic/Kconfig b/drivers/platform/cznic/Kconfig
new file mode 100644
index 000000000000..db5f4a673d28
--- /dev/null
+++ b/drivers/platform/cznic/Kconfig
@@ -0,0 +1,25 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# For a description of the syntax of this configuration file,
+# see Documentation/kbuild/kconfig-language.rst.
+#
+
+menuconfig CZNIC_PLATFORMS
+ bool "Platform support for CZ.NIC's Turris hardware"
+ help
+ Say Y here to be able to choose driver support for CZ.NIC's Turris
+ devices. This option alone does not add any kernel code.
+
+if CZNIC_PLATFORMS
+
+config TURRIS_OMNIA_MCU
+ tristate "Turris Omnia MCU driver"
+ depends on MACH_ARMADA_38X || COMPILE_TEST
+ depends on I2C
+ help
+ Say Y here to add support for the features implemented by the
+ microcontroller on the CZ.NIC's Turris Omnia SOHO router.
+ To compile this driver as a module, choose M here; the module will be
+ called turris-omnia-mcu.
+
+endif # CZNIC_PLATFORMS
diff --git a/drivers/platform/cznic/Makefile b/drivers/platform/cznic/Makefile
new file mode 100644
index 000000000000..31adca73bb94
--- /dev/null
+++ b/drivers/platform/cznic/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+obj-$(CONFIG_TURRIS_OMNIA_MCU) += turris-omnia-mcu.o
+turris-omnia-mcu-y := turris-omnia-mcu-base.o
diff --git a/drivers/platform/cznic/turris-omnia-mcu-base.c b/drivers/platform/cznic/turris-omnia-mcu-base.c
new file mode 100644
index 000000000000..a5ae2ba9abb6
--- /dev/null
+++ b/drivers/platform/cznic/turris-omnia-mcu-base.c
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * CZ.NIC's Turris Omnia MCU driver
+ *
+ * 2024 by Marek Behún <kabel@kernel.org>
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/hex.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/turris-omnia-mcu-interface.h>
+#include <linux/types.h>
+#include <linux/string.h>
+#include <linux/sysfs.h>
+
+#include "turris-omnia-mcu.h"
+
+#define OMNIA_FW_VERSION_LEN 20
+#define OMNIA_FW_VERSION_HEX_LEN (2 * OMNIA_FW_VERSION_LEN + 1)
+#define OMNIA_BOARD_INFO_LEN 16
+
+int omnia_cmd_write_read(const struct i2c_client *client,
+ void *cmd, unsigned int cmd_len,
+ void *reply, unsigned int reply_len)
+{
+ struct i2c_msg msgs[2];
+ int ret, num;
+
+ msgs[0].addr = client->addr;
+ msgs[0].flags = 0;
+ msgs[0].len = cmd_len;
+ msgs[0].buf = cmd;
+ num = 1;
+
+ if (reply_len) {
+ msgs[1].addr = client->addr;
+ msgs[1].flags = I2C_M_RD;
+ msgs[1].len = reply_len;
+ msgs[1].buf = reply;
+ num++;
+ }
+
+ ret = i2c_transfer(client->adapter, msgs, num);
+ if (ret < 0)
+ return ret;
+ if (ret != num)
+ return -EIO;
+
+ return 0;
+}
+
+static int omnia_get_version_hash(struct omnia_mcu *mcu, bool bootloader,
+ char version[static OMNIA_FW_VERSION_HEX_LEN])
+{
+ u8 reply[OMNIA_FW_VERSION_LEN];
+ char *p;
+ int err;
+
+ err = omnia_cmd_read(mcu->client,
+ bootloader ? OMNIA_CMD_GET_FW_VERSION_BOOT
+ : OMNIA_CMD_GET_FW_VERSION_APP,
+ reply, sizeof(reply));
+ if (err)
+ return err;
+
+ p = bin2hex(version, reply, OMNIA_FW_VERSION_LEN);
+ *p = '\0';
+
+ return 0;
+}
+
+static ssize_t fw_version_hash_show(struct device *dev, char *buf,
+ bool bootloader)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+ char version[OMNIA_FW_VERSION_HEX_LEN];
+ int err;
+
+ err = omnia_get_version_hash(mcu, bootloader, version);
+ if (err)
+ return err;
+
+ return sysfs_emit(buf, "%s\n", version);
+}
+
+static ssize_t fw_version_hash_application_show(struct device *dev,
+ struct device_attribute *a,
+ char *buf)
+{
+ return fw_version_hash_show(dev, buf, false);
+}
+static DEVICE_ATTR_RO(fw_version_hash_application);
+
+static ssize_t fw_version_hash_bootloader_show(struct device *dev,
+ struct device_attribute *a,
+ char *buf)
+{
+ return fw_version_hash_show(dev, buf, true);
+}
+static DEVICE_ATTR_RO(fw_version_hash_bootloader);
+
+static ssize_t fw_features_show(struct device *dev, struct device_attribute *a,
+ char *buf)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "0x%x\n", mcu->features);
+}
+static DEVICE_ATTR_RO(fw_features);
+
+static ssize_t mcu_type_show(struct device *dev, struct device_attribute *a,
+ char *buf)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%s\n", mcu->type);
+}
+static DEVICE_ATTR_RO(mcu_type);
+
+static ssize_t reset_selector_show(struct device *dev,
+ struct device_attribute *a, char *buf)
+{
+ u8 reply;
+ int err;
+
+ err = omnia_cmd_read_u8(to_i2c_client(dev), OMNIA_CMD_GET_RESET,
+ &reply);
+ if (err)
+ return err;
+
+ return sysfs_emit(buf, "%d\n", reply);
+}
+static DEVICE_ATTR_RO(reset_selector);
+
+static ssize_t serial_number_show(struct device *dev,
+ struct device_attribute *a, char *buf)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%016llX\n", mcu->board_serial_number);
+}
+static DEVICE_ATTR_RO(serial_number);
+
+static ssize_t first_mac_address_show(struct device *dev,
+ struct device_attribute *a, char *buf)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%pM\n", mcu->board_first_mac);
+}
+static DEVICE_ATTR_RO(first_mac_address);
+
+static ssize_t board_revision_show(struct device *dev,
+ struct device_attribute *a, char *buf)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+
+ return sysfs_emit(buf, "%u\n", mcu->board_revision);
+}
+static DEVICE_ATTR_RO(board_revision);
+
+static struct attribute *omnia_mcu_base_attrs[] = {
+ &dev_attr_fw_version_hash_application.attr,
+ &dev_attr_fw_version_hash_bootloader.attr,
+ &dev_attr_fw_features.attr,
+ &dev_attr_mcu_type.attr,
+ &dev_attr_reset_selector.attr,
+ &dev_attr_serial_number.attr,
+ &dev_attr_first_mac_address.attr,
+ &dev_attr_board_revision.attr,
+ NULL
+};
+
+static umode_t omnia_mcu_base_attrs_visible(struct kobject *kobj,
+ struct attribute *a, int n)
+{
+ struct device *dev = kobj_to_dev(kobj);
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+
+ if ((a == &dev_attr_serial_number.attr ||
+ a == &dev_attr_first_mac_address.attr ||
+ a == &dev_attr_board_revision.attr) &&
+ !(mcu->features & OMNIA_FEAT_BOARD_INFO))
+ return 0;
+
+ return a->mode;
+}
+
+static const struct attribute_group omnia_mcu_base_group = {
+ .attrs = omnia_mcu_base_attrs,
+ .is_visible = omnia_mcu_base_attrs_visible,
+};
+
+static const struct attribute_group *omnia_mcu_groups[] = {
+ &omnia_mcu_base_group,
+ NULL
+};
+
+static void omnia_mcu_print_version_hash(struct omnia_mcu *mcu, bool bootloader)
+{
+ const char *type = bootloader ? "bootloader" : "application";
+ struct device *dev = &mcu->client->dev;
+ char version[OMNIA_FW_VERSION_HEX_LEN];
+ int err;
+
+ err = omnia_get_version_hash(mcu, bootloader, version);
+ if (err) {
+ dev_err(dev, "Cannot read MCU %s firmware version: %d\n",
+ type, err);
+ return;
+ }
+
+ dev_info(dev, "MCU %s firmware version hash: %s\n", type, version);
+}
+
+static const char *omnia_status_to_mcu_type(u16 status)
+{
+ switch (status & OMNIA_STS_MCU_TYPE_MASK) {
+ case OMNIA_STS_MCU_TYPE_STM32:
+ return "STM32";
+ case OMNIA_STS_MCU_TYPE_GD32:
+ return "GD32";
+ case OMNIA_STS_MCU_TYPE_MKL:
+ return "MKL";
+ default:
+ return "unknown";
+ }
+}
+
+static void omnia_info_missing_feature(struct device *dev, const char *feature)
+{
+ dev_info(dev,
+ "Your board's MCU firmware does not support the %s feature.\n",
+ feature);
+}
+
+static int omnia_mcu_read_features(struct omnia_mcu *mcu)
+{
+ static const struct {
+ u16 mask;
+ const char *name;
+ } features[] = {
+#define _DEF_FEAT(_n, _m) { OMNIA_FEAT_ ## _n, _m }
+ _DEF_FEAT(EXT_CMDS, "extended control and status"),
+ _DEF_FEAT(WDT_PING, "watchdog pinging"),
+ _DEF_FEAT(LED_STATE_EXT_MASK, "peripheral LED pins reading"),
+ _DEF_FEAT(NEW_INT_API, "new interrupt API"),
+ _DEF_FEAT(POWEROFF_WAKEUP, "poweroff and wakeup"),
+ _DEF_FEAT(TRNG, "true random number generator"),
+#undef _DEF_FEAT
+ };
+ struct i2c_client *client = mcu->client;
+ struct device *dev = &client->dev;
+ bool suggest_fw_upgrade = false;
+ u16 status;
+ int err;
+
+ /* status word holds MCU type, which we need below */
+ err = omnia_cmd_read_u16(client, OMNIA_CMD_GET_STATUS_WORD, &status);
+ if (err)
+ return err;
+
+ /*
+ * Check whether MCU firmware supports the OMNIA_CMD_GET_FEATURES
+ * command.
+ */
+ if (status & OMNIA_STS_FEATURES_SUPPORTED) {
+ /* try read 32-bit features */
+ err = omnia_cmd_read_u32(client, OMNIA_CMD_GET_FEATURES,
+ &mcu->features);
+ if (err) {
+ /* try read 16-bit features */
+ u16 features16;
+
+ err = omnia_cmd_read_u16(client, OMNIA_CMD_GET_FEATURES,
+ &features16);
+ if (err)
+ return err;
+
+ mcu->features = features16;
+ } else {
+ if (mcu->features & OMNIA_FEAT_FROM_BIT_16_INVALID)
+ mcu->features &= GENMASK(15, 0);
+ }
+ } else {
+ dev_info(dev,
+ "Your board's MCU firmware does not support feature reading.\n");
+ suggest_fw_upgrade = true;
+ }
+
+ mcu->type = omnia_status_to_mcu_type(status);
+ dev_info(dev, "MCU type %s%s\n", mcu->type,
+ (mcu->features & OMNIA_FEAT_PERIPH_MCU) ?
+ ", with peripheral resets wired" : "");
+
+ omnia_mcu_print_version_hash(mcu, true);
+
+ if (mcu->features & OMNIA_FEAT_BOOTLOADER)
+ dev_warn(dev,
+ "MCU is running bootloader firmware. Was firmware upgrade interrupted?\n");
+ else
+ omnia_mcu_print_version_hash(mcu, false);
+
+ for (unsigned int i = 0; i < ARRAY_SIZE(features); i++) {
+ if (mcu->features & features[i].mask)
+ continue;
+
+ omnia_info_missing_feature(dev, features[i].name);
+ suggest_fw_upgrade = true;
+ }
+
+ if (suggest_fw_upgrade)
+ dev_info(dev,
+ "Consider upgrading MCU firmware with the omnia-mcutool utility.\n");
+
+ return 0;
+}
+
+static int omnia_mcu_read_board_info(struct omnia_mcu *mcu)
+{
+ u8 reply[1 + OMNIA_BOARD_INFO_LEN];
+ int err;
+
+ err = omnia_cmd_read(mcu->client, OMNIA_CMD_BOARD_INFO_GET, reply,
+ sizeof(reply));
+ if (err)
+ return err;
+
+ if (reply[0] != OMNIA_BOARD_INFO_LEN)
+ return -EIO;
+
+ mcu->board_serial_number = get_unaligned_le64(&reply[1]);
+
+ /* we can't use ether_addr_copy() because reply is not u16-aligned */
+ memcpy(mcu->board_first_mac, &reply[9], ETH_ALEN);
+
+ mcu->board_revision = reply[15];
+
+ return 0;
+}
+
+static int omnia_mcu_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct omnia_mcu *mcu;
+ int err;
+
+ if (!client->irq)
+ return dev_err_probe(dev, -EINVAL, "IRQ resource not found\n");
+
+ mcu = devm_kzalloc(dev, sizeof(*mcu), GFP_KERNEL);
+ if (!mcu)
+ return -ENOMEM;
+
+ mcu->client = client;
+ i2c_set_clientdata(client, mcu);
+
+ err = omnia_mcu_read_features(mcu);
+ if (err)
+ return dev_err_probe(dev, err,
+ "Cannot determine MCU supported features\n");
+
+ if (mcu->features & OMNIA_FEAT_BOARD_INFO) {
+ err = omnia_mcu_read_board_info(mcu);
+ if (err)
+ return dev_err_probe(dev, err,
+ "Cannot read board info\n");
+ }
+
+ return 0;
+}
+
+static const struct of_device_id of_omnia_mcu_match[] = {
+ { .compatible = "cznic,turris-omnia-mcu" },
+ {}
+};
+
+static struct i2c_driver omnia_mcu_driver = {
+ .probe = omnia_mcu_probe,
+ .driver = {
+ .name = "turris-omnia-mcu",
+ .of_match_table = of_omnia_mcu_match,
+ .dev_groups = omnia_mcu_groups,
+ },
+};
+module_i2c_driver(omnia_mcu_driver);
+
+MODULE_AUTHOR("Marek Behun <kabel@kernel.org>");
+MODULE_DESCRIPTION("CZ.NIC's Turris Omnia MCU");
+MODULE_LICENSE("GPL");
diff --git a/drivers/platform/cznic/turris-omnia-mcu.h b/drivers/platform/cznic/turris-omnia-mcu.h
new file mode 100644
index 000000000000..3d0daa6f13ef
--- /dev/null
+++ b/drivers/platform/cznic/turris-omnia-mcu.h
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * CZ.NIC's Turris Omnia MCU driver
+ *
+ * 2024 by Marek Behún <kabel@kernel.org>
+ */
+
+#ifndef __TURRIS_OMNIA_MCU_H
+#define __TURRIS_OMNIA_MCU_H
+
+#include <linux/if_ether.h>
+#include <linux/types.h>
+#include <asm/byteorder.h>
+
+struct i2c_client;
+
+struct omnia_mcu {
+ struct i2c_client *client;
+ const char *type;
+ u32 features;
+
+ /* board information */
+ u64 board_serial_number;
+ u8 board_first_mac[ETH_ALEN];
+ u8 board_revision;
+};
+
+int omnia_cmd_write_read(const struct i2c_client *client,
+ void *cmd, unsigned int cmd_len,
+ void *reply, unsigned int reply_len);
+
+static inline int omnia_cmd_read(const struct i2c_client *client, u8 cmd,
+ void *reply, unsigned int len)
+{
+ return omnia_cmd_write_read(client, &cmd, 1, reply, len);
+}
+
+static inline int omnia_cmd_read_u32(const struct i2c_client *client, u8 cmd,
+ u32 *dst)
+{
+ __le32 reply;
+ int err;
+
+ err = omnia_cmd_read(client, cmd, &reply, sizeof(reply));
+ if (err)
+ return err;
+
+ *dst = le32_to_cpu(reply);
+
+ return 0;
+}
+
+static inline int omnia_cmd_read_u16(const struct i2c_client *client, u8 cmd,
+ u16 *dst)
+{
+ __le16 reply;
+ int err;
+
+ err = omnia_cmd_read(client, cmd, &reply, sizeof(reply));
+ if (err)
+ return err;
+
+ *dst = le16_to_cpu(reply);
+
+ return 0;
+}
+
+static inline int omnia_cmd_read_u8(const struct i2c_client *client, u8 cmd,
+ u8 *reply)
+{
+ return omnia_cmd_read(client, cmd, reply, sizeof(*reply));
+}
+
+#endif /* __TURRIS_OMNIA_MCU_H */
diff --git a/include/linux/turris-omnia-mcu-interface.h b/include/linux/turris-omnia-mcu-interface.h
new file mode 100644
index 000000000000..2da8cbeb158a
--- /dev/null
+++ b/include/linux/turris-omnia-mcu-interface.h
@@ -0,0 +1,249 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * CZ.NIC's Turris Omnia MCU I2C interface commands definitions
+ *
+ * 2024 by Marek Behún <kabel@kernel.org>
+ */
+
+#ifndef __TURRIS_OMNIA_MCU_INTERFACE_H
+#define __TURRIS_OMNIA_MCU_INTERFACE_H
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+
+enum omnia_commands_e {
+ OMNIA_CMD_GET_STATUS_WORD = 0x01, /* slave sends status word back */
+ OMNIA_CMD_GENERAL_CONTROL = 0x02,
+ OMNIA_CMD_LED_MODE = 0x03, /* default/user */
+ OMNIA_CMD_LED_STATE = 0x04, /* LED on/off */
+ OMNIA_CMD_LED_COLOR = 0x05, /* LED number + RED + GREEN + BLUE */
+ OMNIA_CMD_USER_VOLTAGE = 0x06,
+ OMNIA_CMD_SET_BRIGHTNESS = 0x07,
+ OMNIA_CMD_GET_BRIGHTNESS = 0x08,
+ OMNIA_CMD_GET_RESET = 0x09,
+ OMNIA_CMD_GET_FW_VERSION_APP = 0x0A, /* 20B git hash number */
+ OMNIA_CMD_SET_WATCHDOG_STATE = 0x0B, /* 0 - disable
+ * 1 - enable / ping
+ * after boot watchdog is started
+ * with 2 minutes timeout
+ */
+
+ /* OMNIA_CMD_WATCHDOG_STATUS = 0x0C, not implemented anymore */
+
+ OMNIA_CMD_GET_WATCHDOG_STATE = 0x0D,
+ OMNIA_CMD_GET_FW_VERSION_BOOT = 0x0E, /* 20B Git hash number */
+ OMNIA_CMD_GET_FW_CHECKSUM = 0x0F, /* 4B length, 4B checksum */
+
+ /* available if FEATURES_SUPPORTED bit set in status word */
+ OMNIA_CMD_GET_FEATURES = 0x10,
+
+ /* available if EXT_CMD bit set in features */
+ OMNIA_CMD_GET_EXT_STATUS_DWORD = 0x11,
+ OMNIA_CMD_EXT_CONTROL = 0x12,
+ OMNIA_CMD_GET_EXT_CONTROL_STATUS = 0x13,
+
+ /* available if NEW_INT_API bit set in features */
+ OMNIA_CMD_GET_INT_AND_CLEAR = 0x14,
+ OMNIA_CMD_GET_INT_MASK = 0x15,
+ OMNIA_CMD_SET_INT_MASK = 0x16,
+
+ /* available if FLASHING bit set in features */
+ OMNIA_CMD_FLASH = 0x19,
+
+ /* available if WDT_PING bit set in features */
+ OMNIA_CMD_SET_WDT_TIMEOUT = 0x20,
+ OMNIA_CMD_GET_WDT_TIMELEFT = 0x21,
+
+ /* available if POWEROFF_WAKEUP bit set in features */
+ OMNIA_CMD_SET_WAKEUP = 0x22,
+ OMNIA_CMD_GET_UPTIME_AND_WAKEUP = 0x23,
+ OMNIA_CMD_POWER_OFF = 0x24,
+
+ /* available if USB_OVC_PROT_SETTING bit set in features */
+ OMNIA_CMD_SET_USB_OVC_PROT = 0x25,
+ OMNIA_CMD_GET_USB_OVC_PROT = 0x26,
+
+ /* available if TRNG bit set in features */
+ OMNIA_CMD_TRNG_COLLECT_ENTROPY = 0x28,
+
+ /* available if CRYPTO bit set in features */
+ OMNIA_CMD_CRYPTO_GET_PUBLIC_KEY = 0x29,
+ OMNIA_CMD_CRYPTO_SIGN_MESSAGE = 0x2A,
+ OMNIA_CMD_CRYPTO_COLLECT_SIGNATURE = 0x2B,
+
+ /* available if BOARD_INFO it set in features */
+ OMNIA_CMD_BOARD_INFO_GET = 0x2C,
+ OMNIA_CMD_BOARD_INFO_BURN = 0x2D,
+
+ /* available only at address 0x2b (LED-controller) */
+ /* available only if LED_GAMMA_CORRECTION bit set in features */
+ OMNIA_CMD_SET_GAMMA_CORRECTION = 0x30,
+ OMNIA_CMD_GET_GAMMA_CORRECTION = 0x31,
+
+ /* available only at address 0x2b (LED-controller) */
+ /* available only if PER_LED_CORRECTION bit set in features */
+ /* available only if FROM_BIT_16_INVALID bit NOT set in features */
+ OMNIA_CMD_SET_LED_CORRECTIONS = 0x32,
+ OMNIA_CMD_GET_LED_CORRECTIONS = 0x33,
+};
+
+enum omnia_flashing_commands_e {
+ OMNIA_FLASH_CMD_UNLOCK = 0x01,
+ OMNIA_FLASH_CMD_SIZE_AND_CSUM = 0x02,
+ OMNIA_FLASH_CMD_PROGRAM = 0x03,
+ OMNIA_FLASH_CMD_RESET = 0x04,
+};
+
+enum omnia_sts_word_e {
+ OMNIA_STS_MCU_TYPE_MASK = GENMASK(1, 0),
+ OMNIA_STS_MCU_TYPE_STM32 = FIELD_PREP_CONST(OMNIA_STS_MCU_TYPE_MASK, 0),
+ OMNIA_STS_MCU_TYPE_GD32 = FIELD_PREP_CONST(OMNIA_STS_MCU_TYPE_MASK, 1),
+ OMNIA_STS_MCU_TYPE_MKL = FIELD_PREP_CONST(OMNIA_STS_MCU_TYPE_MASK, 2),
+ OMNIA_STS_FEATURES_SUPPORTED = BIT(2),
+ OMNIA_STS_USER_REGULATOR_NOT_SUPPORTED = BIT(3),
+ OMNIA_STS_CARD_DET = BIT(4),
+ OMNIA_STS_MSATA_IND = BIT(5),
+ OMNIA_STS_USB30_OVC = BIT(6),
+ OMNIA_STS_USB31_OVC = BIT(7),
+ OMNIA_STS_USB30_PWRON = BIT(8),
+ OMNIA_STS_USB31_PWRON = BIT(9),
+ OMNIA_STS_ENABLE_4V5 = BIT(10),
+ OMNIA_STS_BUTTON_MODE = BIT(11),
+ OMNIA_STS_BUTTON_PRESSED = BIT(12),
+ OMNIA_STS_BUTTON_COUNTER_MASK = GENMASK(15, 13),
+};
+
+enum omnia_ctl_byte_e {
+ OMNIA_CTL_LIGHT_RST = BIT(0),
+ OMNIA_CTL_HARD_RST = BIT(1),
+ /* BIT(2) is currently reserved */
+ OMNIA_CTL_USB30_PWRON = BIT(3),
+ OMNIA_CTL_USB31_PWRON = BIT(4),
+ OMNIA_CTL_ENABLE_4V5 = BIT(5),
+ OMNIA_CTL_BUTTON_MODE = BIT(6),
+ OMNIA_CTL_BOOTLOADER = BIT(7),
+};
+
+enum omnia_features_e {
+ OMNIA_FEAT_PERIPH_MCU = BIT(0),
+ OMNIA_FEAT_EXT_CMDS = BIT(1),
+ OMNIA_FEAT_WDT_PING = BIT(2),
+ OMNIA_FEAT_LED_STATE_EXT_MASK = GENMASK(4, 3),
+ OMNIA_FEAT_LED_STATE_EXT = FIELD_PREP_CONST(OMNIA_FEAT_LED_STATE_EXT_MASK, 1),
+ OMNIA_FEAT_LED_STATE_EXT_V32 = FIELD_PREP_CONST(OMNIA_FEAT_LED_STATE_EXT_MASK, 2),
+ OMNIA_FEAT_LED_GAMMA_CORRECTION = BIT(5),
+ OMNIA_FEAT_NEW_INT_API = BIT(6),
+ OMNIA_FEAT_BOOTLOADER = BIT(7),
+ OMNIA_FEAT_FLASHING = BIT(8),
+ OMNIA_FEAT_NEW_MESSAGE_API = BIT(9),
+ OMNIA_FEAT_BRIGHTNESS_INT = BIT(10),
+ OMNIA_FEAT_POWEROFF_WAKEUP = BIT(11),
+ OMNIA_FEAT_CAN_OLD_MESSAGE_API = BIT(12),
+ OMNIA_FEAT_TRNG = BIT(13),
+ OMNIA_FEAT_CRYPTO = BIT(14),
+ OMNIA_FEAT_BOARD_INFO = BIT(15),
+
+ /*
+ * Orginally the features command replied only 16 bits. If more were
+ * read, either the I2C transaction failed or 0xff bytes were sent.
+ * Therefore to consider bits 16 - 31 valid, one bit (20) was reserved
+ * to be zero.
+ */
+
+ /* Bits 16 - 19 correspond to bits 0 - 3 of status word */
+ OMNIA_FEAT_MCU_TYPE_MASK = GENMASK(17, 16),
+ OMNIA_FEAT_MCU_TYPE_STM32 = FIELD_PREP_CONST(OMNIA_FEAT_MCU_TYPE_MASK, 0),
+ OMNIA_FEAT_MCU_TYPE_GD32 = FIELD_PREP_CONST(OMNIA_FEAT_MCU_TYPE_MASK, 1),
+ OMNIA_FEAT_MCU_TYPE_MKL = FIELD_PREP_CONST(OMNIA_FEAT_MCU_TYPE_MASK, 2),
+ OMNIA_FEAT_FEATURES_SUPPORTED = BIT(18),
+ OMNIA_FEAT_USER_REGULATOR_NOT_SUPPORTED = BIT(19),
+
+ /* must not be set */
+ OMNIA_FEAT_FROM_BIT_16_INVALID = BIT(20),
+
+ OMNIA_FEAT_PER_LED_CORRECTION = BIT(21),
+ OMNIA_FEAT_USB_OVC_PROT_SETTING = BIT(22),
+};
+
+enum omnia_ext_sts_dword_e {
+ OMNIA_EXT_STS_SFP_nDET = BIT(0),
+ OMNIA_EXT_STS_LED_STATES_MASK = GENMASK(31, 12),
+ OMNIA_EXT_STS_WLAN0_MSATA_LED = BIT(12),
+ OMNIA_EXT_STS_WLAN1_LED = BIT(13),
+ OMNIA_EXT_STS_WLAN2_LED = BIT(14),
+ OMNIA_EXT_STS_WPAN0_LED = BIT(15),
+ OMNIA_EXT_STS_WPAN1_LED = BIT(16),
+ OMNIA_EXT_STS_WPAN2_LED = BIT(17),
+ OMNIA_EXT_STS_WAN_LED0 = BIT(18),
+ OMNIA_EXT_STS_WAN_LED1 = BIT(19),
+ OMNIA_EXT_STS_LAN0_LED0 = BIT(20),
+ OMNIA_EXT_STS_LAN0_LED1 = BIT(21),
+ OMNIA_EXT_STS_LAN1_LED0 = BIT(22),
+ OMNIA_EXT_STS_LAN1_LED1 = BIT(23),
+ OMNIA_EXT_STS_LAN2_LED0 = BIT(24),
+ OMNIA_EXT_STS_LAN2_LED1 = BIT(25),
+ OMNIA_EXT_STS_LAN3_LED0 = BIT(26),
+ OMNIA_EXT_STS_LAN3_LED1 = BIT(27),
+ OMNIA_EXT_STS_LAN4_LED0 = BIT(28),
+ OMNIA_EXT_STS_LAN4_LED1 = BIT(29),
+ OMNIA_EXT_STS_LAN5_LED0 = BIT(30),
+ OMNIA_EXT_STS_LAN5_LED1 = BIT(31),
+};
+
+enum omnia_ext_ctl_e {
+ OMNIA_EXT_CTL_nRES_MMC = BIT(0),
+ OMNIA_EXT_CTL_nRES_LAN = BIT(1),
+ OMNIA_EXT_CTL_nRES_PHY = BIT(2),
+ OMNIA_EXT_CTL_nPERST0 = BIT(3),
+ OMNIA_EXT_CTL_nPERST1 = BIT(4),
+ OMNIA_EXT_CTL_nPERST2 = BIT(5),
+ OMNIA_EXT_CTL_PHY_SFP = BIT(6),
+ OMNIA_EXT_CTL_PHY_SFP_AUTO = BIT(7),
+ OMNIA_EXT_CTL_nVHV_CTRL = BIT(8),
+};
+
+enum omnia_int_e {
+ OMNIA_INT_CARD_DET = BIT(0),
+ OMNIA_INT_MSATA_IND = BIT(1),
+ OMNIA_INT_USB30_OVC = BIT(2),
+ OMNIA_INT_USB31_OVC = BIT(3),
+ OMNIA_INT_BUTTON_PRESSED = BIT(4),
+ OMNIA_INT_SFP_nDET = BIT(5),
+ OMNIA_INT_BRIGHTNESS_CHANGED = BIT(6),
+ OMNIA_INT_TRNG = BIT(7),
+ OMNIA_INT_MESSAGE_SIGNED = BIT(8),
+
+ OMNIA_INT_LED_STATES_MASK = GENMASK(31, 12),
+ OMNIA_INT_WLAN0_MSATA_LED = BIT(12),
+ OMNIA_INT_WLAN1_LED = BIT(13),
+ OMNIA_INT_WLAN2_LED = BIT(14),
+ OMNIA_INT_WPAN0_LED = BIT(15),
+ OMNIA_INT_WPAN1_LED = BIT(16),
+ OMNIA_INT_WPAN2_LED = BIT(17),
+ OMNIA_INT_WAN_LED0 = BIT(18),
+ OMNIA_INT_WAN_LED1 = BIT(19),
+ OMNIA_INT_LAN0_LED0 = BIT(20),
+ OMNIA_INT_LAN0_LED1 = BIT(21),
+ OMNIA_INT_LAN1_LED0 = BIT(22),
+ OMNIA_INT_LAN1_LED1 = BIT(23),
+ OMNIA_INT_LAN2_LED0 = BIT(24),
+ OMNIA_INT_LAN2_LED1 = BIT(25),
+ OMNIA_INT_LAN3_LED0 = BIT(26),
+ OMNIA_INT_LAN3_LED1 = BIT(27),
+ OMNIA_INT_LAN4_LED0 = BIT(28),
+ OMNIA_INT_LAN4_LED1 = BIT(29),
+ OMNIA_INT_LAN5_LED0 = BIT(30),
+ OMNIA_INT_LAN5_LED1 = BIT(31),
+};
+
+enum omnia_cmd_poweroff_e {
+ OMNIA_CMD_POWER_OFF_POWERON_BUTTON = BIT(0),
+ OMNIA_CMD_POWER_OFF_MAGIC = 0xdead,
+};
+
+enum omnia_cmd_usb_ovc_prot_e {
+ OMNIA_CMD_xET_USB_OVC_PROT_PORT_MASK = GENMASK(3, 0),
+ OMNIA_CMD_xET_USB_OVC_PROT_ENABLE = BIT(4),
+};
+
+#endif /* __TURRIS_OMNIA_MCU_INTERFACE_H */
--
2.44.2
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH v11 3/8] platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs
2024-06-05 16:18 [PATCH v11 0/8] Turris Omnia MCU driver Marek Behún
2024-06-05 16:18 ` [PATCH v11 2/8] platform: cznic: Add preliminary support for Turris Omnia MCU Marek Behún
@ 2024-06-05 16:18 ` Marek Behún
2024-06-05 18:29 ` Andy Shevchenko
2024-06-05 19:05 ` [PATCH v11 0/8] Turris Omnia MCU driver Andy Shevchenko
2 siblings, 1 reply; 8+ messages in thread
From: Marek Behún @ 2024-06-05 16:18 UTC (permalink / raw)
To: Gregory CLEMENT, Arnd Bergmann, soc, arm, Andy Shevchenko,
Hans de Goede, Ilpo Järvinen, Linus Walleij,
Bartosz Golaszewski, linux-gpio
Cc: Marek Behún
Add support for GPIOs connected to the MCU on the Turris Omnia board.
This includes:
- front button pin
- enable pins for USB regulators
- MiniPCIe / mSATA card presence pins in MiniPCIe port 0
- LED output pins from WAN ethernet PHY, LAN switch and MiniPCIe ports
- on board revisions 32+ also various peripheral resets and another
voltage regulator enable pin
Signed-off-by: Marek Behún <kabel@kernel.org>
---
.../sysfs-bus-i2c-devices-turris-omnia-mcu | 16 +
drivers/platform/cznic/Kconfig | 15 +
drivers/platform/cznic/Makefile | 1 +
.../platform/cznic/turris-omnia-mcu-base.c | 3 +-
.../platform/cznic/turris-omnia-mcu-gpio.c | 1071 +++++++++++++++++
drivers/platform/cznic/turris-omnia-mcu.h | 68 ++
6 files changed, 1173 insertions(+), 1 deletion(-)
create mode 100644 drivers/platform/cznic/turris-omnia-mcu-gpio.c
diff --git a/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu b/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
index 9bc5aad00de0..86360249080c 100644
--- a/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
+++ b/Documentation/ABI/testing/sysfs-bus-i2c-devices-turris-omnia-mcu
@@ -22,6 +22,22 @@ Description: (RO) Contains device first MAC address. Each Turris Omnia is
Format: %pM.
+What: /sys/bus/i2c/devices/<mcu_device>/front_button_mode
+Date: September 2024
+KernelVersion: 6.11
+Contact: Marek Behún <kabel@kernel.org>
+Description: (RW) The front button on the Turris Omnia router can be
+ configured either to change the intensity of all the LEDs on the
+ front panel, or to send the press event to the CPU as an
+ interrupt.
+
+ This file switches between these two modes:
+ - "mcu" makes the button press event be handled by the MCU to
+ change the LEDs panel intensity.
+ - "cpu" makes the button press event be handled by the CPU.
+
+ Format: %s.
+
What: /sys/bus/i2c/devices/<mcu_device>/fw_features
Date: September 2024
KernelVersion: 6.11
diff --git a/drivers/platform/cznic/Kconfig b/drivers/platform/cznic/Kconfig
index db5f4a673d28..d95e7c83c7ae 100644
--- a/drivers/platform/cznic/Kconfig
+++ b/drivers/platform/cznic/Kconfig
@@ -16,9 +16,24 @@ config TURRIS_OMNIA_MCU
tristate "Turris Omnia MCU driver"
depends on MACH_ARMADA_38X || COMPILE_TEST
depends on I2C
+ select GPIOLIB
+ select GPIOLIB_IRQCHIP
help
Say Y here to add support for the features implemented by the
microcontroller on the CZ.NIC's Turris Omnia SOHO router.
+ The features include:
+ - GPIO pins
+ - to get front button press events (the front button can be
+ configured either to generate press events to the CPU or to change
+ front LEDs panel brightness)
+ - to enable / disable USB port voltage regulators and to detect
+ USB overcurrent
+ - to detect MiniPCIe / mSATA card presence in MiniPCIe port 0
+ - to configure resets of various peripherals on board revisions 32+
+ - to enable / disable the VHV voltage regulator to the SOC in order
+ to be able to program SOC's OTP on board revisions 32+
+ - to get input from the LED output pins of the WAN ethernet PHY, LAN
+ switch and MiniPCIe ports
To compile this driver as a module, choose M here; the module will be
called turris-omnia-mcu.
diff --git a/drivers/platform/cznic/Makefile b/drivers/platform/cznic/Makefile
index 31adca73bb94..53fd8f1777a3 100644
--- a/drivers/platform/cznic/Makefile
+++ b/drivers/platform/cznic/Makefile
@@ -2,3 +2,4 @@
obj-$(CONFIG_TURRIS_OMNIA_MCU) += turris-omnia-mcu.o
turris-omnia-mcu-y := turris-omnia-mcu-base.o
+turris-omnia-mcu-y += turris-omnia-mcu-gpio.o
diff --git a/drivers/platform/cznic/turris-omnia-mcu-base.c b/drivers/platform/cznic/turris-omnia-mcu-base.c
index a5ae2ba9abb6..03a5f19c6665 100644
--- a/drivers/platform/cznic/turris-omnia-mcu-base.c
+++ b/drivers/platform/cznic/turris-omnia-mcu-base.c
@@ -196,6 +196,7 @@ static const struct attribute_group omnia_mcu_base_group = {
static const struct attribute_group *omnia_mcu_groups[] = {
&omnia_mcu_base_group,
+ &omnia_mcu_gpio_group,
NULL
};
@@ -370,7 +371,7 @@ static int omnia_mcu_probe(struct i2c_client *client)
"Cannot read board info\n");
}
- return 0;
+ return omnia_mcu_register_gpiochip(mcu);
}
static const struct of_device_id of_omnia_mcu_match[] = {
diff --git a/drivers/platform/cznic/turris-omnia-mcu-gpio.c b/drivers/platform/cznic/turris-omnia-mcu-gpio.c
new file mode 100644
index 000000000000..bc7965e6c879
--- /dev/null
+++ b/drivers/platform/cznic/turris-omnia-mcu-gpio.c
@@ -0,0 +1,1071 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * CZ.NIC's Turris Omnia MCU GPIO and IRQ driver
+ *
+ * 2024 by Marek Behún <kabel@kernel.org>
+ */
+
+#include <linux/array_size.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/bug.h>
+#include <linux/cleanup.h>
+#include <linux/device.h>
+#include <linux/devm-helpers.h>
+#include <linux/gpio/driver.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/turris-omnia-mcu-interface.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+#include <asm/unaligned.h>
+
+#include "turris-omnia-mcu.h"
+
+#define OMNIA_CMD_INT_ARG_LEN 8
+#define FRONT_BUTTON_RELEASE_DELAY_MS 50
+
+static const char * const omnia_mcu_gpio_templates[64] = {
+ /* GPIOs with value read from the 16-bit wide status */
+ [4] = "MiniPCIe0 Card Detect",
+ [5] = "MiniPCIe0 mSATA Indicator",
+ [6] = "Front USB3 port over-current",
+ [7] = "Rear USB3 port over-current",
+ [8] = "Front USB3 port power",
+ [9] = "Rear USB3 port power",
+ [12] = "Front Button",
+
+ /* GPIOs with value read from the 32-bit wide extended status */
+ [16] = "SFP nDET",
+ [28] = "MiniPCIe0 LED",
+ [29] = "MiniPCIe1 LED",
+ [30] = "MiniPCIe2 LED",
+ [31] = "MiniPCIe0 PAN LED",
+ [32] = "MiniPCIe1 PAN LED",
+ [33] = "MiniPCIe2 PAN LED",
+ [34] = "WAN PHY LED0",
+ [35] = "WAN PHY LED1",
+ [36] = "LAN switch p0 LED0",
+ [37] = "LAN switch p0 LED1",
+ [38] = "LAN switch p1 LED0",
+ [39] = "LAN switch p1 LED1",
+ [40] = "LAN switch p2 LED0",
+ [41] = "LAN switch p2 LED1",
+ [42] = "LAN switch p3 LED0",
+ [43] = "LAN switch p3 LED1",
+ [44] = "LAN switch p4 LED0",
+ [45] = "LAN switch p4 LED1",
+ [46] = "LAN switch p5 LED0",
+ [47] = "LAN switch p5 LED1",
+
+ /* GPIOs with value read from the 16-bit wide extended control status */
+ [48] = "eMMC nRESET",
+ [49] = "LAN switch nRESET",
+ [50] = "WAN PHY nRESET",
+ [51] = "MiniPCIe0 nPERST",
+ [52] = "MiniPCIe1 nPERST",
+ [53] = "MiniPCIe2 nPERST",
+ [54] = "WAN PHY SFP mux",
+};
+
+struct omnia_gpio {
+ u8 cmd, ctl_cmd, bit, ctl_bit, int_bit;
+ bool has_int;
+ u16 feat, feat_mask;
+};
+
+#define _DEF_GPIO(_cmd, _ctl_cmd, _bit, _ctl_bit, _int_bit, _feat, _feat_mask) \
+ { \
+ .cmd = _cmd, \
+ .ctl_cmd = _ctl_cmd, \
+ .bit = _bit, \
+ .ctl_bit = _ctl_bit, \
+ .int_bit = _int_bit, \
+ .has_int = (_int_bit) != -1, \
+ .feat = _feat, \
+ .feat_mask = _feat_mask, \
+ }
+#define _DEF_GPIO_STS(_name) \
+ _DEF_GPIO(OMNIA_CMD_GET_STATUS_WORD, 0, __bf_shf(OMNIA_STS_ ## _name), \
+ 0, __bf_shf(OMNIA_INT_ ## _name), 0, 0)
+#define _DEF_GPIO_CTL(_name) \
+ _DEF_GPIO(OMNIA_CMD_GET_STATUS_WORD, OMNIA_CMD_GENERAL_CONTROL, \
+ __bf_shf(OMNIA_STS_ ## _name), __bf_shf(OMNIA_CTL_ ## _name), \
+ -1, 0, 0)
+#define _DEF_GPIO_EXT_STS(_name, _feat) \
+ _DEF_GPIO(OMNIA_CMD_GET_EXT_STATUS_DWORD, 0, \
+ __bf_shf(OMNIA_EXT_STS_ ## _name), 0, \
+ __bf_shf(OMNIA_INT_ ## _name), \
+ OMNIA_FEAT_ ## _feat | OMNIA_FEAT_EXT_CMDS, \
+ OMNIA_FEAT_ ## _feat | OMNIA_FEAT_EXT_CMDS)
+#define _DEF_GPIO_EXT_STS_LED(_name, _ledext) \
+ _DEF_GPIO(OMNIA_CMD_GET_EXT_STATUS_DWORD, 0, \
+ __bf_shf(OMNIA_EXT_STS_ ## _name), 0, \
+ __bf_shf(OMNIA_INT_ ## _name), \
+ OMNIA_FEAT_LED_STATE_ ## _ledext, \
+ OMNIA_FEAT_LED_STATE_EXT_MASK)
+#define _DEF_GPIO_EXT_STS_LEDALL(_name) \
+ _DEF_GPIO(OMNIA_CMD_GET_EXT_STATUS_DWORD, 0, \
+ __bf_shf(OMNIA_EXT_STS_ ## _name), 0, \
+ __bf_shf(OMNIA_INT_ ## _name), \
+ OMNIA_FEAT_LED_STATE_EXT_MASK, 0)
+#define _DEF_GPIO_EXT_CTL(_name, _feat) \
+ _DEF_GPIO(OMNIA_CMD_GET_EXT_CONTROL_STATUS, OMNIA_CMD_EXT_CONTROL, \
+ __bf_shf(OMNIA_EXT_CTL_ ## _name), \
+ __bf_shf(OMNIA_EXT_CTL_ ## _name), -1, \
+ OMNIA_FEAT_ ## _feat | OMNIA_FEAT_EXT_CMDS, \
+ OMNIA_FEAT_ ## _feat | OMNIA_FEAT_EXT_CMDS)
+#define _DEF_INT(_name) \
+ _DEF_GPIO(0, 0, 0, 0, __bf_shf(OMNIA_INT_ ## _name), 0, 0)
+
+static const struct omnia_gpio omnia_gpios[64] = {
+ /* GPIOs with value read from the 16-bit wide status */
+ [4] = _DEF_GPIO_STS(CARD_DET),
+ [5] = _DEF_GPIO_STS(MSATA_IND),
+ [6] = _DEF_GPIO_STS(USB30_OVC),
+ [7] = _DEF_GPIO_STS(USB31_OVC),
+ [8] = _DEF_GPIO_CTL(USB30_PWRON),
+ [9] = _DEF_GPIO_CTL(USB31_PWRON),
+
+ /* brightness changed interrupt, no GPIO */
+ [11] = _DEF_INT(BRIGHTNESS_CHANGED),
+
+ [12] = _DEF_GPIO_STS(BUTTON_PRESSED),
+
+ /* TRNG interrupt, no GPIO */
+ [13] = _DEF_INT(TRNG),
+
+ /* MESSAGE_SIGNED interrupt, no GPIO */
+ [14] = _DEF_INT(MESSAGE_SIGNED),
+
+ /* GPIOs with value read from the 32-bit wide extended status */
+ [16] = _DEF_GPIO_EXT_STS(SFP_nDET, PERIPH_MCU),
+ [28] = _DEF_GPIO_EXT_STS_LEDALL(WLAN0_MSATA_LED),
+ [29] = _DEF_GPIO_EXT_STS_LEDALL(WLAN1_LED),
+ [30] = _DEF_GPIO_EXT_STS_LEDALL(WLAN2_LED),
+ [31] = _DEF_GPIO_EXT_STS_LED(WPAN0_LED, EXT),
+ [32] = _DEF_GPIO_EXT_STS_LED(WPAN1_LED, EXT),
+ [33] = _DEF_GPIO_EXT_STS_LED(WPAN2_LED, EXT),
+ [34] = _DEF_GPIO_EXT_STS_LEDALL(WAN_LED0),
+ [35] = _DEF_GPIO_EXT_STS_LED(WAN_LED1, EXT_V32),
+ [36] = _DEF_GPIO_EXT_STS_LEDALL(LAN0_LED0),
+ [37] = _DEF_GPIO_EXT_STS_LEDALL(LAN0_LED1),
+ [38] = _DEF_GPIO_EXT_STS_LEDALL(LAN1_LED0),
+ [39] = _DEF_GPIO_EXT_STS_LEDALL(LAN1_LED1),
+ [40] = _DEF_GPIO_EXT_STS_LEDALL(LAN2_LED0),
+ [41] = _DEF_GPIO_EXT_STS_LEDALL(LAN2_LED1),
+ [42] = _DEF_GPIO_EXT_STS_LEDALL(LAN3_LED0),
+ [43] = _DEF_GPIO_EXT_STS_LEDALL(LAN3_LED1),
+ [44] = _DEF_GPIO_EXT_STS_LEDALL(LAN4_LED0),
+ [45] = _DEF_GPIO_EXT_STS_LEDALL(LAN4_LED1),
+ [46] = _DEF_GPIO_EXT_STS_LEDALL(LAN5_LED0),
+ [47] = _DEF_GPIO_EXT_STS_LEDALL(LAN5_LED1),
+
+ /* GPIOs with value read from the 16-bit wide extended control status */
+ [48] = _DEF_GPIO_EXT_CTL(nRES_MMC, PERIPH_MCU),
+ [49] = _DEF_GPIO_EXT_CTL(nRES_LAN, PERIPH_MCU),
+ [50] = _DEF_GPIO_EXT_CTL(nRES_PHY, PERIPH_MCU),
+ [51] = _DEF_GPIO_EXT_CTL(nPERST0, PERIPH_MCU),
+ [52] = _DEF_GPIO_EXT_CTL(nPERST1, PERIPH_MCU),
+ [53] = _DEF_GPIO_EXT_CTL(nPERST2, PERIPH_MCU),
+ [54] = _DEF_GPIO_EXT_CTL(PHY_SFP, PERIPH_MCU),
+};
+
+/* mapping from interrupts to indexes of GPIOs in the omnia_gpios array */
+static const u8 omnia_int_to_gpio_idx[32] = {
+ [__bf_shf(OMNIA_INT_CARD_DET)] = 4,
+ [__bf_shf(OMNIA_INT_MSATA_IND)] = 5,
+ [__bf_shf(OMNIA_INT_USB30_OVC)] = 6,
+ [__bf_shf(OMNIA_INT_USB31_OVC)] = 7,
+ [__bf_shf(OMNIA_INT_BUTTON_PRESSED)] = 12,
+ [__bf_shf(OMNIA_INT_TRNG)] = 13,
+ [__bf_shf(OMNIA_INT_MESSAGE_SIGNED)] = 14,
+ [__bf_shf(OMNIA_INT_SFP_nDET)] = 16,
+ [__bf_shf(OMNIA_INT_BRIGHTNESS_CHANGED)] = 11,
+ [__bf_shf(OMNIA_INT_WLAN0_MSATA_LED)] = 28,
+ [__bf_shf(OMNIA_INT_WLAN1_LED)] = 29,
+ [__bf_shf(OMNIA_INT_WLAN2_LED)] = 30,
+ [__bf_shf(OMNIA_INT_WPAN0_LED)] = 31,
+ [__bf_shf(OMNIA_INT_WPAN1_LED)] = 32,
+ [__bf_shf(OMNIA_INT_WPAN2_LED)] = 33,
+ [__bf_shf(OMNIA_INT_WAN_LED0)] = 34,
+ [__bf_shf(OMNIA_INT_WAN_LED1)] = 35,
+ [__bf_shf(OMNIA_INT_LAN0_LED0)] = 36,
+ [__bf_shf(OMNIA_INT_LAN0_LED1)] = 37,
+ [__bf_shf(OMNIA_INT_LAN1_LED0)] = 38,
+ [__bf_shf(OMNIA_INT_LAN1_LED1)] = 39,
+ [__bf_shf(OMNIA_INT_LAN2_LED0)] = 40,
+ [__bf_shf(OMNIA_INT_LAN2_LED1)] = 41,
+ [__bf_shf(OMNIA_INT_LAN3_LED0)] = 42,
+ [__bf_shf(OMNIA_INT_LAN3_LED1)] = 43,
+ [__bf_shf(OMNIA_INT_LAN4_LED0)] = 44,
+ [__bf_shf(OMNIA_INT_LAN4_LED1)] = 45,
+ [__bf_shf(OMNIA_INT_LAN5_LED0)] = 46,
+ [__bf_shf(OMNIA_INT_LAN5_LED1)] = 47,
+};
+
+/* index of PHY_SFP GPIO in the omnia_gpios array */
+#define OMNIA_GPIO_PHY_SFP_OFFSET 54
+
+static int omnia_ctl_cmd_locked(struct omnia_mcu *mcu, u8 cmd, u16 val, u16 mask)
+{
+ unsigned int len;
+ u8 buf[5];
+
+ buf[0] = cmd;
+
+ switch (cmd) {
+ case OMNIA_CMD_GENERAL_CONTROL:
+ buf[1] = val;
+ buf[2] = mask;
+ len = 3;
+ break;
+
+ case OMNIA_CMD_EXT_CONTROL:
+ put_unaligned_le16(val, &buf[1]);
+ put_unaligned_le16(mask, &buf[3]);
+ len = 5;
+ break;
+
+ default:
+ BUG();
+ }
+
+ return omnia_cmd_write(mcu->client, buf, len);
+}
+
+static int omnia_ctl_cmd(struct omnia_mcu *mcu, u8 cmd, u16 val, u16 mask)
+{
+ guard(mutex)(&mcu->lock);
+
+ return omnia_ctl_cmd_locked(mcu, cmd, val, mask);
+}
+
+static int omnia_gpio_request(struct gpio_chip *gc, unsigned int offset)
+{
+ if (!omnia_gpios[offset].cmd)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int omnia_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+
+ if (offset == OMNIA_GPIO_PHY_SFP_OFFSET) {
+ int val;
+
+ scoped_guard(mutex, &mcu->lock) {
+ val = omnia_cmd_read_bit(mcu->client,
+ OMNIA_CMD_GET_EXT_CONTROL_STATUS,
+ OMNIA_EXT_CTL_PHY_SFP_AUTO);
+ if (val < 0)
+ return val;
+ }
+
+ if (val)
+ return GPIO_LINE_DIRECTION_IN;
+
+ return GPIO_LINE_DIRECTION_OUT;
+ }
+
+ if (omnia_gpios[offset].ctl_cmd)
+ return GPIO_LINE_DIRECTION_OUT;
+
+ return GPIO_LINE_DIRECTION_IN;
+}
+
+static int omnia_gpio_direction_input(struct gpio_chip *gc, unsigned int offset)
+{
+ const struct omnia_gpio *gpio = &omnia_gpios[offset];
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+
+ if (offset == OMNIA_GPIO_PHY_SFP_OFFSET)
+ return omnia_ctl_cmd(mcu, OMNIA_CMD_EXT_CONTROL,
+ OMNIA_EXT_CTL_PHY_SFP_AUTO,
+ OMNIA_EXT_CTL_PHY_SFP_AUTO);
+
+ if (gpio->ctl_cmd)
+ return -ENOTSUPP;
+
+ return 0;
+}
+
+static int omnia_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ const struct omnia_gpio *gpio = &omnia_gpios[offset];
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ u16 val, mask;
+
+ if (!gpio->ctl_cmd)
+ return -ENOTSUPP;
+
+ mask = BIT(gpio->ctl_bit);
+ val = value ? mask : 0;
+
+ if (offset == OMNIA_GPIO_PHY_SFP_OFFSET)
+ mask |= OMNIA_EXT_CTL_PHY_SFP_AUTO;
+
+ return omnia_ctl_cmd(mcu, gpio->ctl_cmd, val, mask);
+}
+
+static int omnia_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+ const struct omnia_gpio *gpio = &omnia_gpios[offset];
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+
+ /*
+ * If firmware does not support the new interrupt API, we are informed
+ * of every change of the status word by an interrupt from MCU and save
+ * its value in the interrupt service routine. Simply return the saved
+ * value.
+ */
+ if (gpio->cmd == OMNIA_CMD_GET_STATUS_WORD &&
+ !(mcu->features & OMNIA_FEAT_NEW_INT_API))
+ return test_bit(gpio->bit, &mcu->last_status);
+
+ guard(mutex)(&mcu->lock);
+
+ /*
+ * If firmware does support the new interrupt API, we may have cached
+ * the value of a GPIO in the interrupt service routine. If not, read
+ * the relevant bit now.
+ */
+ if (gpio->has_int && test_bit(gpio->int_bit, &mcu->is_cached))
+ return test_bit(gpio->int_bit, &mcu->cached);
+
+ return omnia_cmd_read_bit(mcu->client, gpio->cmd, BIT(gpio->bit));
+}
+
+static unsigned long *
+_relevant_field_for_sts_cmd(u8 cmd, unsigned long *sts, unsigned long *ext_sts,
+ unsigned long *ext_ctl)
+{
+ switch (cmd) {
+ case OMNIA_CMD_GET_STATUS_WORD:
+ return sts;
+ case OMNIA_CMD_GET_EXT_STATUS_DWORD:
+ return ext_sts;
+ case OMNIA_CMD_GET_EXT_CONTROL_STATUS:
+ return ext_ctl;
+ default:
+ return NULL;
+ }
+}
+
+static int omnia_gpio_get_multiple(struct gpio_chip *gc, unsigned long *mask,
+ unsigned long *bits)
+{
+ unsigned long sts = 0, ext_sts = 0, ext_ctl = 0, *field;
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ struct i2c_client *client = mcu->client;
+ int err, i;
+
+ /* determine which bits to read from the 3 possible commands */
+ for_each_set_bit(i, mask, ARRAY_SIZE(omnia_gpios)) {
+ field = _relevant_field_for_sts_cmd(omnia_gpios[i].cmd,
+ &sts, &ext_sts, &ext_ctl);
+
+ if (field)
+ __set_bit(omnia_gpios[i].bit, field);
+ }
+
+ guard(mutex)(&mcu->lock);
+
+ if (mcu->features & OMNIA_FEAT_NEW_INT_API) {
+ /* read relevant bits from status */
+ err = omnia_cmd_read_bits(client, OMNIA_CMD_GET_STATUS_WORD,
+ sts, &sts);
+ if (err)
+ return err;
+ } else {
+ /*
+ * Use status word value cached in the interrupt service routine
+ * if firmware does not support the new interrupt API.
+ */
+ sts = mcu->last_status;
+ }
+
+ /* read relevant bits from extended status */
+ err = omnia_cmd_read_bits(client, OMNIA_CMD_GET_EXT_STATUS_DWORD,
+ ext_sts, &ext_sts);
+ if (err)
+ return err;
+
+ /* read relevant bits from extended control */
+ err = omnia_cmd_read_bits(client, OMNIA_CMD_GET_EXT_CONTROL_STATUS,
+ ext_ctl, &ext_ctl);
+ if (err)
+ return err;
+
+ /* assign relevant bits in result */
+ for_each_set_bit(i, mask, ARRAY_SIZE(omnia_gpios)) {
+ field = _relevant_field_for_sts_cmd(omnia_gpios[i].cmd,
+ &sts, &ext_sts, &ext_ctl);
+
+ if (field)
+ __assign_bit(i, bits,
+ test_bit(omnia_gpios[i].bit, field));
+ }
+
+ return 0;
+}
+
+static void omnia_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
+{
+ const struct omnia_gpio *gpio = &omnia_gpios[offset];
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ u16 val, mask;
+
+ if (!gpio->ctl_cmd)
+ return;
+
+ mask = BIT(gpio->ctl_bit);
+ val = value ? mask : 0;
+
+ omnia_ctl_cmd(mcu, gpio->ctl_cmd, val, mask);
+}
+
+static void omnia_gpio_set_multiple(struct gpio_chip *gc, unsigned long *mask,
+ unsigned long *bits)
+{
+ unsigned long ctl = 0, ctl_mask = 0, ext_ctl = 0, ext_ctl_mask = 0;
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ int i;
+
+ for_each_set_bit(i, mask, ARRAY_SIZE(omnia_gpios)) {
+ unsigned long *field, *field_mask;
+ u8 bit = omnia_gpios[i].ctl_bit;
+
+ switch (omnia_gpios[i].ctl_cmd) {
+ case OMNIA_CMD_GENERAL_CONTROL:
+ field = &ctl;
+ field_mask = &ctl_mask;
+ break;
+ case OMNIA_CMD_EXT_CONTROL:
+ field = &ext_ctl;
+ field_mask = &ext_ctl_mask;
+ break;
+ default:
+ field = field_mask = NULL;
+ break;
+ }
+
+ if (field) {
+ __set_bit(bit, field_mask);
+ __assign_bit(bit, field, test_bit(i, bits));
+ }
+ }
+
+ guard(mutex)(&mcu->lock);
+
+ if (ctl_mask)
+ omnia_ctl_cmd_locked(mcu, OMNIA_CMD_GENERAL_CONTROL,
+ ctl, ctl_mask);
+
+ if (ext_ctl_mask)
+ omnia_ctl_cmd_locked(mcu, OMNIA_CMD_EXT_CONTROL,
+ ext_ctl, ext_ctl_mask);
+}
+
+static bool omnia_gpio_available(struct omnia_mcu *mcu,
+ const struct omnia_gpio *gpio)
+{
+ if (gpio->feat_mask)
+ return (mcu->features & gpio->feat_mask) == gpio->feat;
+
+ if (gpio->feat)
+ return mcu->features & gpio->feat;
+
+ return true;
+}
+
+static int omnia_gpio_init_valid_mask(struct gpio_chip *gc,
+ unsigned long *valid_mask,
+ unsigned int ngpios)
+{
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+
+ for (unsigned int i = 0; i < ngpios; i++) {
+ const struct omnia_gpio *gpio = &omnia_gpios[i];
+
+ if (gpio->cmd || gpio->has_int)
+ __assign_bit(i, valid_mask,
+ omnia_gpio_available(mcu, gpio));
+ else
+ __clear_bit(i, valid_mask);
+ }
+
+ return 0;
+}
+
+static int omnia_gpio_of_xlate(struct gpio_chip *gc,
+ const struct of_phandle_args *gpiospec,
+ u32 *flags)
+{
+ u32 bank, gpio;
+
+ if (WARN_ON(gpiospec->args_count != 3))
+ return -EINVAL;
+
+ if (flags)
+ *flags = gpiospec->args[2];
+
+ bank = gpiospec->args[0];
+ gpio = gpiospec->args[1];
+
+ switch (bank) {
+ case 0:
+ return gpio < 16 ? gpio : -EINVAL;
+ case 1:
+ return gpio < 32 ? 16 + gpio : -EINVAL;
+ case 2:
+ return gpio < 16 ? 48 + gpio : -EINVAL;
+ default:
+ return -EINVAL;
+ }
+}
+
+static void omnia_irq_shutdown(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ u8 bit = omnia_gpios[hwirq].int_bit;
+
+ __clear_bit(bit, &mcu->rising);
+ __clear_bit(bit, &mcu->falling);
+}
+
+static void omnia_irq_mask(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ u8 bit = omnia_gpios[hwirq].int_bit;
+
+ if (!omnia_gpios[hwirq].cmd)
+ __clear_bit(bit, &mcu->rising);
+ __clear_bit(bit, &mcu->mask);
+ gpiochip_disable_irq(gc, hwirq);
+}
+
+static void omnia_irq_unmask(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ u8 bit = omnia_gpios[hwirq].int_bit;
+
+ gpiochip_enable_irq(gc, hwirq);
+ __set_bit(bit, &mcu->mask);
+ if (!omnia_gpios[hwirq].cmd)
+ __set_bit(bit, &mcu->rising);
+}
+
+static int omnia_irq_set_type(struct irq_data *d, unsigned int type)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ struct device *dev = &mcu->client->dev;
+ u8 bit = omnia_gpios[hwirq].int_bit;
+
+ if (!(type & IRQ_TYPE_EDGE_BOTH)) {
+ dev_err(dev, "irq %u: unsupported type %u\n", d->irq, type);
+ return -EINVAL;
+ }
+
+ __assign_bit(bit, &mcu->rising, type & IRQ_TYPE_EDGE_RISING);
+ __assign_bit(bit, &mcu->falling, type & IRQ_TYPE_EDGE_FALLING);
+
+ return 0;
+}
+
+static void omnia_irq_bus_lock(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+
+ /* nothing to do if MCU firmware does not support new interrupt API */
+ if (!(mcu->features & OMNIA_FEAT_NEW_INT_API))
+ return;
+
+ mutex_lock(&mcu->lock);
+}
+
+/**
+ * omnia_mask_interleave - Interleaves the bytes from @rising and @falling
+ * @dst: the destination u8 array of interleaved bytes
+ * @rising: rising mask
+ * @falling: falling mask
+ *
+ * Interleaves the little-endian bytes from @rising and @falling words.
+ *
+ * If @rising = (r0, r1, r2, r3) and @falling = (f0, f1, f2, f3), the result is
+ * @dst = (r0, f0, r1, f1, r2, f2, r3, f3).
+ *
+ * The MCU receives an interrupt mask and reports a pending interrupt bitmap in
+ * this interleaved format. The rationale behind this is that the low-indexed
+ * bits are more important - in many cases, the user will be interested only in
+ * interrupts with indexes 0 to 7, and so the system can stop reading after
+ * first 2 bytes (r0, f0), to save time on the slow I2C bus.
+ *
+ * Feel free to remove this function and its inverse, omnia_mask_deinterleave,
+ * and use an appropriate bitmap_*() function once such a function exists.
+ */
+static void
+omnia_mask_interleave(u8 *dst, unsigned long rising, unsigned long falling)
+{
+ for (int i = 0; i < sizeof(u32); ++i) {
+ dst[2 * i] = rising >> (8 * i);
+ dst[2 * i + 1] = falling >> (8 * i);
+ }
+}
+
+/**
+ * omnia_mask_deinterleave - Deinterleaves the bytes into @rising and @falling
+ * @src: the source u8 array containing the interleaved bytes
+ * @rising: pointer where to store the rising mask gathered from @src
+ * @falling: pointer where to store the falling mask gathered from @src
+ *
+ * This is the inverse function to omnia_mask_interleave.
+ */
+static void omnia_mask_deinterleave(const u8 *src, unsigned long *rising,
+ unsigned long *falling)
+{
+ *rising = *falling = 0;
+
+ for (int i = 0; i < sizeof(u32); ++i) {
+ *rising |= src[2 * i] << (8 * i);
+ *falling |= src[2 * i + 1] << (8 * i);
+ }
+}
+
+static void omnia_irq_bus_sync_unlock(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ struct device *dev = &mcu->client->dev;
+ u8 cmd[1 + OMNIA_CMD_INT_ARG_LEN];
+ unsigned long rising, falling;
+ int err;
+
+ /* nothing to do if MCU firmware does not support new interrupt API */
+ if (!(mcu->features & OMNIA_FEAT_NEW_INT_API))
+ return;
+
+ cmd[0] = OMNIA_CMD_SET_INT_MASK;
+
+ rising = mcu->rising & mcu->mask;
+ falling = mcu->falling & mcu->mask;
+
+ /* interleave the rising and falling bytes into the command arguments */
+ omnia_mask_interleave(&cmd[1], rising, falling);
+
+ dev_dbg(dev, "set int mask %8ph\n", &cmd[1]);
+
+ err = omnia_cmd_write(mcu->client, cmd, sizeof(cmd));
+ if (err) {
+ dev_err(dev, "Cannot set mask: %d\n", err);
+ goto unlock;
+ }
+
+ /*
+ * Remember which GPIOs have both rising and falling interrupts enabled.
+ * For those we will cache their value so that .get() method is faster.
+ * We also need to forget cached values of GPIOs that aren't cached
+ * anymore.
+ */
+ mcu->both = rising & falling;
+ mcu->is_cached &= mcu->both;
+
+unlock:
+ mutex_unlock(&mcu->lock);
+}
+
+static const struct irq_chip omnia_mcu_irq_chip = {
+ .name = "Turris Omnia MCU interrupts",
+ .irq_shutdown = omnia_irq_shutdown,
+ .irq_mask = omnia_irq_mask,
+ .irq_unmask = omnia_irq_unmask,
+ .irq_set_type = omnia_irq_set_type,
+ .irq_bus_lock = omnia_irq_bus_lock,
+ .irq_bus_sync_unlock = omnia_irq_bus_sync_unlock,
+ .flags = IRQCHIP_IMMUTABLE,
+ GPIOCHIP_IRQ_RESOURCE_HELPERS,
+};
+
+static void omnia_irq_init_valid_mask(struct gpio_chip *gc,
+ unsigned long *valid_mask,
+ unsigned int ngpios)
+{
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+
+ for (unsigned int i = 0; i < ngpios; i++) {
+ const struct omnia_gpio *gpio = &omnia_gpios[i];
+
+ if (gpio->has_int)
+ __assign_bit(i, valid_mask,
+ omnia_gpio_available(mcu, gpio));
+ else
+ __clear_bit(i, valid_mask);
+ }
+}
+
+static int omnia_irq_init_hw(struct gpio_chip *gc)
+{
+ struct omnia_mcu *mcu = gpiochip_get_data(gc);
+ u8 cmd[1 + OMNIA_CMD_INT_ARG_LEN] = {};
+
+ cmd[0] = OMNIA_CMD_SET_INT_MASK;
+
+ return omnia_cmd_write(mcu->client, cmd, sizeof(cmd));
+}
+
+/*
+ * Determine how many bytes we need to read from the reply to the
+ * OMNIA_CMD_GET_INT_AND_CLEAR command in order to retrieve all unmasked
+ * interrupts.
+ */
+static unsigned int
+omnia_irq_compute_pending_length(unsigned long rising, unsigned long falling)
+{
+ return max(omnia_compute_reply_length(rising, true, 0),
+ omnia_compute_reply_length(falling, true, 1));
+}
+
+static bool omnia_irq_read_pending_new(struct omnia_mcu *mcu,
+ unsigned long *pending)
+{
+ struct device *dev = &mcu->client->dev;
+ u8 reply[OMNIA_CMD_INT_ARG_LEN] = {};
+ unsigned long rising, falling;
+ unsigned int len;
+ int err;
+
+ len = omnia_irq_compute_pending_length(mcu->rising & mcu->mask,
+ mcu->falling & mcu->mask);
+ if (!len)
+ return false;
+
+ guard(mutex)(&mcu->lock);
+
+ err = omnia_cmd_read(mcu->client, OMNIA_CMD_GET_INT_AND_CLEAR, reply,
+ len);
+ if (err) {
+ dev_err(dev, "Cannot read pending IRQs: %d\n", err);
+ return false;
+ }
+
+ /* deinterleave the reply bytes into rising and falling */
+ omnia_mask_deinterleave(reply, &rising, &falling);
+
+ rising &= mcu->mask;
+ falling &= mcu->mask;
+ *pending = rising | falling;
+
+ /* cache values for GPIOs that have both edges enabled */
+ mcu->is_cached &= ~(rising & falling);
+ mcu->is_cached |= mcu->both & (rising ^ falling);
+ mcu->cached = (mcu->cached | rising) & ~falling;
+
+ return true;
+}
+
+static int omnia_read_status_word_old_fw(struct omnia_mcu *mcu,
+ unsigned long *status)
+{
+ u16 raw_status;
+ int err;
+
+ err = omnia_cmd_read_u16(mcu->client, OMNIA_CMD_GET_STATUS_WORD,
+ &raw_status);
+ if (err)
+ return err;
+
+ /*
+ * Old firmware has a bug wherein it never resets the USB port
+ * overcurrent bits back to zero. Ignore them.
+ */
+ *status = raw_status & ~(OMNIA_STS_USB30_OVC | OMNIA_STS_USB31_OVC);
+
+ return 0;
+}
+
+static void button_release_emul_fn(struct work_struct *work)
+{
+ struct omnia_mcu *mcu = container_of(to_delayed_work(work),
+ struct omnia_mcu,
+ button_release_emul_work);
+
+ mcu->button_pressed_emul = false;
+ generic_handle_irq_safe(mcu->client->irq);
+}
+
+static void
+fill_int_from_sts(unsigned long *rising, unsigned long *falling,
+ unsigned long rising_sts, unsigned long falling_sts,
+ unsigned long sts_bit, unsigned long int_bit)
+{
+ if (rising_sts & sts_bit)
+ *rising |= int_bit;
+ if (falling_sts & sts_bit)
+ *falling |= int_bit;
+}
+
+static bool omnia_irq_read_pending_old(struct omnia_mcu *mcu,
+ unsigned long *pending)
+{
+ unsigned long status, rising_sts, falling_sts, rising, falling;
+ struct device *dev = &mcu->client->dev;
+ int err;
+
+ guard(mutex)(&mcu->lock);
+
+ err = omnia_read_status_word_old_fw(mcu, &status);
+ if (err) {
+ dev_err(dev, "Cannot read pending IRQs: %d\n", err);
+ return false;
+ }
+
+ /*
+ * The old firmware triggers an interrupt whenever status word changes,
+ * but does not inform about which bits rose or fell. We need to compute
+ * this here by comparing with the last status word value.
+ *
+ * The OMNIA_STS_BUTTON_PRESSED bit needs special handling, because the
+ * old firmware clears the OMNIA_STS_BUTTON_PRESSED bit on successful
+ * completion of the OMNIA_CMD_GET_STATUS_WORD command, resulting in
+ * another interrupt:
+ * - first we get an interrupt, we read the status word where
+ * OMNIA_STS_BUTTON_PRESSED is present,
+ * - MCU clears the OMNIA_STS_BUTTON_PRESSED bit because we read the
+ * status word,
+ * - we get another interrupt because the status word changed again
+ * (the OMNIA_STS_BUTTON_PRESSED bit was cleared).
+ *
+ * The gpiolib-cdev, gpiolib-sysfs and gpio-keys input driver all call
+ * the gpiochip's .get() method after an edge event on a requested GPIO
+ * occurs.
+ *
+ * We ensure that the .get() method reads 1 for the button GPIO for some
+ * time.
+ */
+
+ if (status & OMNIA_STS_BUTTON_PRESSED) {
+ mcu->button_pressed_emul = true;
+ mod_delayed_work(system_wq, &mcu->button_release_emul_work,
+ msecs_to_jiffies(FRONT_BUTTON_RELEASE_DELAY_MS));
+ } else if (mcu->button_pressed_emul) {
+ status |= OMNIA_STS_BUTTON_PRESSED;
+ }
+
+ rising_sts = ~mcu->last_status & status;
+ falling_sts = mcu->last_status & ~status;
+
+ mcu->last_status = status;
+
+ /*
+ * Fill in the relevant interrupt bits from status bits for CARD_DET,
+ * MSATA_IND and BUTTON_PRESSED.
+ */
+ rising = 0;
+ falling = 0;
+ fill_int_from_sts(&rising, &falling, rising_sts, falling_sts,
+ OMNIA_STS_CARD_DET, OMNIA_INT_CARD_DET);
+ fill_int_from_sts(&rising, &falling, rising_sts, falling_sts,
+ OMNIA_STS_MSATA_IND, OMNIA_INT_MSATA_IND);
+ fill_int_from_sts(&rising, &falling, rising_sts, falling_sts,
+ OMNIA_STS_BUTTON_PRESSED, OMNIA_INT_BUTTON_PRESSED);
+
+ /* Use only bits that are enabled */
+ rising &= mcu->rising & mcu->mask;
+ falling &= mcu->falling & mcu->mask;
+ *pending = rising | falling;
+
+ return true;
+}
+
+static bool omnia_irq_read_pending(struct omnia_mcu *mcu,
+ unsigned long *pending)
+{
+ if (mcu->features & OMNIA_FEAT_NEW_INT_API)
+ return omnia_irq_read_pending_new(mcu, pending);
+ else
+ return omnia_irq_read_pending_old(mcu, pending);
+}
+
+static irqreturn_t omnia_irq_thread_handler(int irq, void *dev_id)
+{
+ struct omnia_mcu *mcu = dev_id;
+ struct irq_domain *domain;
+ unsigned long pending;
+ int i;
+
+ if (!omnia_irq_read_pending(mcu, &pending))
+ return IRQ_NONE;
+
+ domain = mcu->gc.irq.domain;
+
+ for_each_set_bit(i, &pending, 32) {
+ unsigned int nested_irq;
+
+ nested_irq = irq_find_mapping(domain, omnia_int_to_gpio_idx[i]);
+
+ handle_nested_irq(nested_irq);
+ }
+
+ return IRQ_RETVAL(pending);
+}
+
+static const char * const front_button_modes[] = { "mcu", "cpu" };
+
+static ssize_t front_button_mode_show(struct device *dev,
+ struct device_attribute *a, char *buf)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+ int val;
+
+ if (mcu->features & OMNIA_FEAT_NEW_INT_API) {
+ val = omnia_cmd_read_bit(mcu->client, OMNIA_CMD_GET_STATUS_WORD,
+ OMNIA_STS_BUTTON_MODE);
+ if (val < 0)
+ return val;
+ } else {
+ val = !!(mcu->last_status & OMNIA_STS_BUTTON_MODE);
+ }
+
+ return sysfs_emit(buf, "%s\n", front_button_modes[val]);
+}
+
+static ssize_t front_button_mode_store(struct device *dev,
+ struct device_attribute *a,
+ const char *buf, size_t count)
+{
+ struct omnia_mcu *mcu = dev_get_drvdata(dev);
+ int err, i;
+
+ i = sysfs_match_string(front_button_modes, buf);
+ if (i < 0)
+ return i;
+
+ err = omnia_ctl_cmd_locked(mcu, OMNIA_CMD_GENERAL_CONTROL,
+ i ? OMNIA_CTL_BUTTON_MODE : 0,
+ OMNIA_CTL_BUTTON_MODE);
+ if (err)
+ return err;
+
+ return count;
+}
+static DEVICE_ATTR_RW(front_button_mode);
+
+static struct attribute *omnia_mcu_gpio_attrs[] = {
+ &dev_attr_front_button_mode.attr,
+ NULL
+};
+
+const struct attribute_group omnia_mcu_gpio_group = {
+ .attrs = omnia_mcu_gpio_attrs,
+};
+
+int omnia_mcu_register_gpiochip(struct omnia_mcu *mcu)
+{
+ bool new_api = mcu->features & OMNIA_FEAT_NEW_INT_API;
+ struct device *dev = &mcu->client->dev;
+ unsigned long irqflags;
+ int err;
+
+ err = devm_mutex_init(dev, &mcu->lock);
+ if (err)
+ return err;
+
+ mcu->gc.request = omnia_gpio_request;
+ mcu->gc.get_direction = omnia_gpio_get_direction;
+ mcu->gc.direction_input = omnia_gpio_direction_input;
+ mcu->gc.direction_output = omnia_gpio_direction_output;
+ mcu->gc.get = omnia_gpio_get;
+ mcu->gc.get_multiple = omnia_gpio_get_multiple;
+ mcu->gc.set = omnia_gpio_set;
+ mcu->gc.set_multiple = omnia_gpio_set_multiple;
+ mcu->gc.init_valid_mask = omnia_gpio_init_valid_mask;
+ mcu->gc.can_sleep = true;
+ mcu->gc.names = omnia_mcu_gpio_templates;
+ mcu->gc.base = -1;
+ mcu->gc.ngpio = ARRAY_SIZE(omnia_gpios);
+ mcu->gc.label = "Turris Omnia MCU GPIOs";
+ mcu->gc.parent = dev;
+ mcu->gc.owner = THIS_MODULE;
+ mcu->gc.of_gpio_n_cells = 3;
+ mcu->gc.of_xlate = omnia_gpio_of_xlate;
+
+ gpio_irq_chip_set_chip(&mcu->gc.irq, &omnia_mcu_irq_chip);
+ /* This will let us handle the parent IRQ in the driver */
+ mcu->gc.irq.parent_handler = NULL;
+ mcu->gc.irq.num_parents = 0;
+ mcu->gc.irq.parents = NULL;
+ mcu->gc.irq.default_type = IRQ_TYPE_NONE;
+ mcu->gc.irq.handler = handle_bad_irq;
+ mcu->gc.irq.threaded = true;
+ if (new_api)
+ mcu->gc.irq.init_hw = omnia_irq_init_hw;
+ mcu->gc.irq.init_valid_mask = omnia_irq_init_valid_mask;
+
+ err = devm_gpiochip_add_data(dev, &mcu->gc, mcu);
+ if (err)
+ return dev_err_probe(dev, err, "Cannot add GPIO chip\n");
+
+ /*
+ * Before requesting the interrupt, if firmware does not support the new
+ * interrupt API, we need to cache the value of the status word, so that
+ * when it changes, we may compare the new value with the cached one in
+ * the interrupt handler.
+ */
+ if (!new_api) {
+ err = omnia_read_status_word_old_fw(mcu, &mcu->last_status);
+ if (err)
+ return dev_err_probe(dev, err,
+ "Cannot read status word\n");
+
+ INIT_DELAYED_WORK(&mcu->button_release_emul_work,
+ button_release_emul_fn);
+ }
+
+ irqflags = IRQF_ONESHOT;
+ if (new_api)
+ irqflags |= IRQF_TRIGGER_LOW;
+ else
+ irqflags |= IRQF_TRIGGER_FALLING;
+
+ err = devm_request_threaded_irq(dev, mcu->client->irq, NULL,
+ omnia_irq_thread_handler, irqflags,
+ "turris-omnia-mcu", mcu);
+ if (err)
+ return dev_err_probe(dev, err, "Cannot request IRQ\n");
+
+ if (!new_api) {
+ /*
+ * The button_release_emul_work has to be initialized before the
+ * thread is requested, and on driver remove it needs to be
+ * canceled before the thread is freed. Therefore we can't use
+ * devm_delayed_work_autocancel() directly, because the order
+ * devm_delayed_work_autocancel();
+ * devm_request_threaded_irq();
+ * would cause improper release order:
+ * free_irq();
+ * cancel_delayed_work_sync();
+ * Instead we first initialize the work above, and only now
+ * after IRQ is requested we add the work devm action.
+ */
+ err = devm_add_action(dev, devm_delayed_work_drop,
+ &mcu->button_release_emul_work);
+ if (err)
+ return err;
+ }
+
+ return 0;
+}
diff --git a/drivers/platform/cznic/turris-omnia-mcu.h b/drivers/platform/cznic/turris-omnia-mcu.h
index 3d0daa6f13ef..3d2dd0054499 100644
--- a/drivers/platform/cznic/turris-omnia-mcu.h
+++ b/drivers/platform/cznic/turris-omnia-mcu.h
@@ -8,8 +8,12 @@
#ifndef __TURRIS_OMNIA_MCU_H
#define __TURRIS_OMNIA_MCU_H
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
#include <linux/if_ether.h>
+#include <linux/mutex.h>
#include <linux/types.h>
+#include <linux/workqueue.h>
#include <asm/byteorder.h>
struct i2c_client;
@@ -23,18 +27,78 @@ struct omnia_mcu {
u64 board_serial_number;
u8 board_first_mac[ETH_ALEN];
u8 board_revision;
+
+ /* GPIO chip */
+ struct gpio_chip gc;
+ struct mutex lock;
+ unsigned long mask, rising, falling, both, cached, is_cached;
+ /* Old MCU firmware handling needs the following */
+ struct delayed_work button_release_emul_work;
+ unsigned long last_status;
+ bool button_pressed_emul;
};
int omnia_cmd_write_read(const struct i2c_client *client,
void *cmd, unsigned int cmd_len,
void *reply, unsigned int reply_len);
+static inline int omnia_cmd_write(const struct i2c_client *client, void *cmd,
+ unsigned int len)
+{
+ return omnia_cmd_write_read(client, cmd, len, NULL, 0);
+}
+
static inline int omnia_cmd_read(const struct i2c_client *client, u8 cmd,
void *reply, unsigned int len)
{
return omnia_cmd_write_read(client, &cmd, 1, reply, len);
}
+static inline unsigned int
+omnia_compute_reply_length(unsigned long mask, bool interleaved,
+ unsigned int offset)
+{
+ if (!mask)
+ return 0;
+
+ return ((__fls(mask) >> 3) << interleaved) + 1 + offset;
+}
+
+/* Returns 0 on success */
+static inline int omnia_cmd_read_bits(const struct i2c_client *client, u8 cmd,
+ unsigned long bits, unsigned long *dst)
+{
+ __le32 reply;
+ int err;
+
+ if (!bits) {
+ *dst = 0;
+ return 0;
+ }
+
+ err = omnia_cmd_read(client, cmd, &reply,
+ omnia_compute_reply_length(bits, false, 0));
+ if (err)
+ return err;
+
+ *dst = le32_to_cpu(reply) & bits;
+
+ return 0;
+}
+
+static inline int omnia_cmd_read_bit(const struct i2c_client *client, u8 cmd,
+ unsigned long bit)
+{
+ unsigned long reply;
+ int err;
+
+ err = omnia_cmd_read_bits(client, cmd, bit, &reply);
+ if (err)
+ return err;
+
+ return !!reply;
+}
+
static inline int omnia_cmd_read_u32(const struct i2c_client *client, u8 cmd,
u32 *dst)
{
@@ -71,4 +135,8 @@ static inline int omnia_cmd_read_u8(const struct i2c_client *client, u8 cmd,
return omnia_cmd_read(client, cmd, reply, sizeof(*reply));
}
+extern const struct attribute_group omnia_mcu_gpio_group;
+
+int omnia_mcu_register_gpiochip(struct omnia_mcu *mcu);
+
#endif /* __TURRIS_OMNIA_MCU_H */
--
2.44.2
^ permalink raw reply related [flat|nested] 8+ messages in thread