Re: [PATCH v3 6/6] gpiolib: notify user-space about in-kernel line state changes

[Kent Gibson <warthog618@gmail.com>]

On Wed, Oct 16, 2024 at 11:02:37AM +0200, Bartosz Golaszewski wrote:
> On Wed, Oct 16, 2024 at 10:57 AM Kent Gibson <warthog618@gmail.com> wrote:
> >
> > On Wed, Oct 16, 2024 at 09:50:58AM +0200, Bartosz Golaszewski wrote:
> > > On Wed, Oct 16, 2024 at 9:27 AM Kent Gibson <warthog618@gmail.com> wrote:
> > > >
> > > > On Wed, Oct 16, 2024 at 01:19:44PM +0800, Kent Gibson wrote:
> > > > > On Tue, Oct 15, 2024 at 12:56:18PM +0200, Bartosz Golaszewski wrote:
> > > > > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > > > > >
> > > > > > -   return gpio_do_set_config(guard.gc, gpio_chip_hwgpio(desc), config);
> > > > > > +   ret = gpio_do_set_config(guard.gc, gpio_chip_hwgpio(desc), config);
> > > > > > +   if (ret == 0) {
> > > > > > +           /* These are the only options we notify the userspace about. */
> > > > > > +           switch (pinconf_to_config_param(config)) {
> > > > > > +           case PIN_CONFIG_BIAS_DISABLE:
> > > > > > +           case PIN_CONFIG_BIAS_PULL_DOWN:
> > > > > > +           case PIN_CONFIG_BIAS_PULL_UP:
> > > > > > +           case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> > > > > > +           case PIN_CONFIG_DRIVE_OPEN_SOURCE:
> > > > > > +           case PIN_CONFIG_DRIVE_PUSH_PULL:
> > > > > > +           case PIN_CONFIG_INPUT_DEBOUNCE:
> > > > > > +                   gpiod_line_state_notify(desc,
> > > > > > +                                           GPIO_V2_LINE_CHANGED_CONFIG);
> > > > > > +                   break;
> > > > > > +           default:
> > > > > > +                   break;
> > > > > > +           }
> > > > > > +   }
> > > > > > +
> > > > > > +   return ret;
> > > > > >  }
> > > > >
> > > > > Ah, the debounce - I forgot about that, and other features that cdev
> > > > > might emulate.
> > > > >
> > > > > What happens if userspace requests a line with debounce that is
> > > > > supported by hardware?  Seems to me we'll see both a LINE_REQUESTED and a
> > > > > LINE_CONFIG_CHANGED when the line is requested.
> > > > >
> > > >
> > > > This is problematic for me to test at the moment, as gpiosim doesn't support
> > > > debounce. Any chance we could make that configurable?  Similarly drive.
> > > >
> > > > > Conversely, what if a config change impacts features that don't result in a
> > > > > notification from gpiod_set_config(), like active low, or emulated
> > > > > drive or debounce?
> > > > >
> > > >
> > > > Bah, drive is emulated in gpiolib itself, so that should be fine.
> > > >
> > > > When changing config cdev always calls gpiod_direction_input/output(), so I
> > > > think that covers the active low case.
> > > >
> > > > But I have a test taking a line from input to output|open_drain and I
> > > > get two change events.  The first is the most interesting as it reports
> > > > input|open_drain, the second then reports output|open_drain.
> > > > That is due to gpiod_direction_output() calling gpiod_set_config() to
> > >
> > > No, it never calls gpiod_set_config() but gpio_set_config() which
> > > never emits an event.
> > >
> >
> > Depends whether the driver supports drive or not.
> >
> > If it does then
> > line 2858:
> >
> >                 ret = gpio_set_config(desc, PIN_CONFIG_DRIVE_OPEN_DRAIN);
> >
>
> I'm seeing this:
>
> gpiod_direction_output_nonotify()
>   gpio_set_config()
>     gpio_set_config_with_argument()
>       gpio_do_set_config()
>         gc->set_config()
>
> There's no call to gpiod_line_state_notify() in this path.
>

Ah, my bad - thought it was gpiod_set_config().
So it is just the gpiod_direction_input() calls.

Cheers,
Kent.