[PATCH v3 0/4] samsung: pinctrl: Add support for eint_fltcon_offset and filter selection on gs101

[PATCH v3 0/4] samsung: pinctrl: Add support for eint_fltcon_offset and filter selection on gs101

[Peter Griffin]

Hi folks,

This series fixes support for correctly saving and restoring fltcon0
and fltcon1 registers on gs101 for non-alive banks where the fltcon
register offset is not at a fixed offset (unlike previous SoCs).
This is done by adding a eint_fltcon_offset and providing GS101
specific pin macros that take an additional parameter (similar to
how exynosautov920 handles it's eint_con_offset).

Additionally the SoC specific suspend and resume callbacks are
re-factored so that each SoC variant has it's own callback containing
the peculiarities for that SoC.

Finally support for filter selection on alive banks is added, this is
currently only enabled for gs101. The code path can be excercised using
`echo mem > /sys/power/state`

regards,

Peter

To: Krzysztof Kozlowski <krzk@kernel.org>
To: Sylwester Nawrocki <s.nawrocki@samsung.com>
To: Alim Akhtar <alim.akhtar@samsung.com>
To: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andre.draszik@linaro.org
Cc: tudor.ambarus@linaro.org
Cc: willmcvicker@google.com
Cc: semen.protsenko@linaro.org
Cc: kernel-team@android.com
Cc: jaewon02.kim@samsung.com

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
Changes in v3:

- Ensure EXYNOS_FLTCON_DIGITAL bit is cleared (Andre)
- Make it obvious that exynos_eint_set_filter() is conditional on bank type (Andre)
- Make it obvious exynos_set_wakeup() is conditional on bank type (Andre)
- Align style where the '+' is placed first (Andre)
- Remove unnecessary braces (Andre)
- Link to v2: https://lore.kernel.org/r/20250301-pinctrl-fltcon-suspend-v2-0-a7eef9bb443b@linaro.org

Changes in v2:
- Remove eint_flt_selectable bool as it can be deduced from EINT_TYPE_WKUP (Peter)
- Move filter config register comment to header file (Andre)
- Rename EXYNOS_FLTCON_DELAY to EXYNOS_FLTCON_ANALOG (Andre)
- Remove misleading old comment (Andre)
- Refactor exynos_eint_update_flt_reg() into a loop (Andre)
- Split refactor of suspend/resume callbacks & gs101 parts into separate patches (Andre)
- Link to v1: https://lore.kernel.org/r/20250120-pinctrl-fltcon-suspend-v1-0-e77900b2a854@linaro.org

---
Peter Griffin (4):
      pinctrl: samsung: add support for eint_fltcon_offset
      pinctrl: samsung: add dedicated SoC eint suspend/resume callbacks
      pinctrl: samsung: add gs101 specific eint suspend/resume callbacks
      pinctrl: samsung: Add filter selection support for alive bank on gs101

 drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 150 ++++++-------
 drivers/pinctrl/samsung/pinctrl-exynos.c       | 294 +++++++++++++++----------
 drivers/pinctrl/samsung/pinctrl-exynos.h       |  50 ++++-
 drivers/pinctrl/samsung/pinctrl-samsung.c      |  12 +-
 drivers/pinctrl/samsung/pinctrl-samsung.h      |  12 +-
 5 files changed, 318 insertions(+), 200 deletions(-)
---
base-commit: 0761652a3b3b607787aebc386d412b1d0ae8008c
change-id: 20250120-pinctrl-fltcon-suspend-2333a137c4d4

Best regards,
-- 
Peter Griffin <peter.griffin@linaro.org>

[PATCH v3 1/4] pinctrl: samsung: add support for eint_fltcon_offset

[Peter Griffin]

On gs101 SoC the fltcon0 (filter configuration 0) offset
isn't at a fixed offset like previous SoCs as the fltcon1
register only exists when there are more than 4 pins in the
bank.

Add a eint_fltcon_offset and new GS101_PIN_BANK_EINT*
macros that take an additional fltcon_offs variable.

This can then be used in suspend/resume callbacks to
save and restore the fltcon0 and fltcon1 registers.

Fixes: 4a8be01a1a7a ("pinctrl: samsung: Add gs101 SoC pinctrl configuration")
Cc: stable@vger.kernel.org
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 98 +++++++++++++-------------
 drivers/pinctrl/samsung/pinctrl-exynos.h       | 22 ++++++
 drivers/pinctrl/samsung/pinctrl-samsung.c      |  1 +
 drivers/pinctrl/samsung/pinctrl-samsung.h      |  4 ++
 4 files changed, 76 insertions(+), 49 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
index 3ea7106ce5eae3c21f11790b5a40037042c1d407..e28fe81776466b693417c66bb15752d609b79eb1 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
@@ -1370,83 +1370,83 @@ const struct samsung_pinctrl_of_match_data fsd_of_data __initconst = {
 
 /* pin banks of gs101 pin-controller (ALIVE) */
 static const struct samsung_pin_bank_data gs101_pin_alive[] = {
-	EXYNOS850_PIN_BANK_EINTW(8, 0x0, "gpa0", 0x00),
-	EXYNOS850_PIN_BANK_EINTW(7, 0x20, "gpa1", 0x04),
-	EXYNOS850_PIN_BANK_EINTW(5, 0x40, "gpa2", 0x08),
-	EXYNOS850_PIN_BANK_EINTW(4, 0x60, "gpa3", 0x0c),
-	EXYNOS850_PIN_BANK_EINTW(4, 0x80, "gpa4", 0x10),
-	EXYNOS850_PIN_BANK_EINTW(7, 0xa0, "gpa5", 0x14),
-	EXYNOS850_PIN_BANK_EINTW(8, 0xc0, "gpa9", 0x18),
-	EXYNOS850_PIN_BANK_EINTW(2, 0xe0, "gpa10", 0x1c),
+	GS101_PIN_BANK_EINTW(8, 0x0, "gpa0", 0x00, 0x00),
+	GS101_PIN_BANK_EINTW(7, 0x20, "gpa1", 0x04, 0x08),
+	GS101_PIN_BANK_EINTW(5, 0x40, "gpa2", 0x08, 0x10),
+	GS101_PIN_BANK_EINTW(4, 0x60, "gpa3", 0x0c, 0x18),
+	GS101_PIN_BANK_EINTW(4, 0x80, "gpa4", 0x10, 0x1c),
+	GS101_PIN_BANK_EINTW(7, 0xa0, "gpa5", 0x14, 0x20),
+	GS101_PIN_BANK_EINTW(8, 0xc0, "gpa9", 0x18, 0x28),
+	GS101_PIN_BANK_EINTW(2, 0xe0, "gpa10", 0x1c, 0x30),
 };
 
 /* pin banks of gs101 pin-controller (FAR_ALIVE) */
 static const struct samsung_pin_bank_data gs101_pin_far_alive[] = {
-	EXYNOS850_PIN_BANK_EINTW(8, 0x0, "gpa6", 0x00),
-	EXYNOS850_PIN_BANK_EINTW(4, 0x20, "gpa7", 0x04),
-	EXYNOS850_PIN_BANK_EINTW(8, 0x40, "gpa8", 0x08),
-	EXYNOS850_PIN_BANK_EINTW(2, 0x60, "gpa11", 0x0c),
+	GS101_PIN_BANK_EINTW(8, 0x0, "gpa6", 0x00, 0x00),
+	GS101_PIN_BANK_EINTW(4, 0x20, "gpa7", 0x04, 0x08),
+	GS101_PIN_BANK_EINTW(8, 0x40, "gpa8", 0x08, 0x0c),
+	GS101_PIN_BANK_EINTW(2, 0x60, "gpa11", 0x0c, 0x14),
 };
 
 /* pin banks of gs101 pin-controller (GSACORE) */
 static const struct samsung_pin_bank_data gs101_pin_gsacore[] = {
-	EXYNOS850_PIN_BANK_EINTG(2, 0x0, "gps0", 0x00),
-	EXYNOS850_PIN_BANK_EINTG(8, 0x20, "gps1", 0x04),
-	EXYNOS850_PIN_BANK_EINTG(3, 0x40, "gps2", 0x08),
+	GS101_PIN_BANK_EINTG(2, 0x0, "gps0", 0x00, 0x00),
+	GS101_PIN_BANK_EINTG(8, 0x20, "gps1", 0x04, 0x04),
+	GS101_PIN_BANK_EINTG(3, 0x40, "gps2", 0x08, 0x0c),
 };
 
 /* pin banks of gs101 pin-controller (GSACTRL) */
 static const struct samsung_pin_bank_data gs101_pin_gsactrl[] = {
-	EXYNOS850_PIN_BANK_EINTW(6, 0x0, "gps3", 0x00),
+	GS101_PIN_BANK_EINTW(6, 0x0, "gps3", 0x00, 0x00),
 };
 
 /* pin banks of gs101 pin-controller (PERIC0) */
 static const struct samsung_pin_bank_data gs101_pin_peric0[] = {
-	EXYNOS850_PIN_BANK_EINTG(5, 0x0, "gpp0", 0x00),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x20, "gpp1", 0x04),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x40, "gpp2", 0x08),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x60, "gpp3", 0x0c),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x80, "gpp4", 0x10),
-	EXYNOS850_PIN_BANK_EINTG(2, 0xa0, "gpp5", 0x14),
-	EXYNOS850_PIN_BANK_EINTG(4, 0xc0, "gpp6", 0x18),
-	EXYNOS850_PIN_BANK_EINTG(2, 0xe0, "gpp7", 0x1c),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x100, "gpp8", 0x20),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x120, "gpp9", 0x24),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x140, "gpp10", 0x28),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x160, "gpp11", 0x2c),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x180, "gpp12", 0x30),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x1a0, "gpp13", 0x34),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x1c0, "gpp14", 0x38),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x1e0, "gpp15", 0x3c),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x200, "gpp16", 0x40),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x220, "gpp17", 0x44),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x240, "gpp18", 0x48),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x260, "gpp19", 0x4c),
+	GS101_PIN_BANK_EINTG(5, 0x0, "gpp0", 0x00, 0x00),
+	GS101_PIN_BANK_EINTG(4, 0x20, "gpp1", 0x04, 0x08),
+	GS101_PIN_BANK_EINTG(4, 0x40, "gpp2", 0x08, 0x0c),
+	GS101_PIN_BANK_EINTG(2, 0x60, "gpp3", 0x0c, 0x10),
+	GS101_PIN_BANK_EINTG(4, 0x80, "gpp4", 0x10, 0x14),
+	GS101_PIN_BANK_EINTG(2, 0xa0, "gpp5", 0x14, 0x18),
+	GS101_PIN_BANK_EINTG(4, 0xc0, "gpp6", 0x18, 0x1c),
+	GS101_PIN_BANK_EINTG(2, 0xe0, "gpp7", 0x1c, 0x20),
+	GS101_PIN_BANK_EINTG(4, 0x100, "gpp8", 0x20, 0x24),
+	GS101_PIN_BANK_EINTG(2, 0x120, "gpp9", 0x24, 0x28),
+	GS101_PIN_BANK_EINTG(4, 0x140, "gpp10", 0x28, 0x2c),
+	GS101_PIN_BANK_EINTG(2, 0x160, "gpp11", 0x2c, 0x30),
+	GS101_PIN_BANK_EINTG(4, 0x180, "gpp12", 0x30, 0x34),
+	GS101_PIN_BANK_EINTG(2, 0x1a0, "gpp13", 0x34, 0x38),
+	GS101_PIN_BANK_EINTG(4, 0x1c0, "gpp14", 0x38, 0x3c),
+	GS101_PIN_BANK_EINTG(2, 0x1e0, "gpp15", 0x3c, 0x40),
+	GS101_PIN_BANK_EINTG(4, 0x200, "gpp16", 0x40, 0x44),
+	GS101_PIN_BANK_EINTG(2, 0x220, "gpp17", 0x44, 0x48),
+	GS101_PIN_BANK_EINTG(4, 0x240, "gpp18", 0x48, 0x4c),
+	GS101_PIN_BANK_EINTG(4, 0x260, "gpp19", 0x4c, 0x50),
 };
 
 /* pin banks of gs101 pin-controller (PERIC1) */
 static const struct samsung_pin_bank_data gs101_pin_peric1[] = {
-	EXYNOS850_PIN_BANK_EINTG(8, 0x0, "gpp20", 0x00),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x20, "gpp21", 0x04),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x40, "gpp22", 0x08),
-	EXYNOS850_PIN_BANK_EINTG(8, 0x60, "gpp23", 0x0c),
-	EXYNOS850_PIN_BANK_EINTG(4, 0x80, "gpp24", 0x10),
-	EXYNOS850_PIN_BANK_EINTG(4, 0xa0, "gpp25", 0x14),
-	EXYNOS850_PIN_BANK_EINTG(5, 0xc0, "gpp26", 0x18),
-	EXYNOS850_PIN_BANK_EINTG(4, 0xe0, "gpp27", 0x1c),
+	GS101_PIN_BANK_EINTG(8, 0x0, "gpp20", 0x00, 0x00),
+	GS101_PIN_BANK_EINTG(4, 0x20, "gpp21", 0x04, 0x08),
+	GS101_PIN_BANK_EINTG(2, 0x40, "gpp22", 0x08, 0x0c),
+	GS101_PIN_BANK_EINTG(8, 0x60, "gpp23", 0x0c, 0x10),
+	GS101_PIN_BANK_EINTG(4, 0x80, "gpp24", 0x10, 0x18),
+	GS101_PIN_BANK_EINTG(4, 0xa0, "gpp25", 0x14, 0x1c),
+	GS101_PIN_BANK_EINTG(5, 0xc0, "gpp26", 0x18, 0x20),
+	GS101_PIN_BANK_EINTG(4, 0xe0, "gpp27", 0x1c, 0x28),
 };
 
 /* pin banks of gs101 pin-controller (HSI1) */
 static const struct samsung_pin_bank_data gs101_pin_hsi1[] = {
-	EXYNOS850_PIN_BANK_EINTG(6, 0x0, "gph0", 0x00),
-	EXYNOS850_PIN_BANK_EINTG(7, 0x20, "gph1", 0x04),
+	GS101_PIN_BANK_EINTG(6, 0x0, "gph0", 0x00, 0x00),
+	GS101_PIN_BANK_EINTG(7, 0x20, "gph1", 0x04, 0x08),
 };
 
 /* pin banks of gs101 pin-controller (HSI2) */
 static const struct samsung_pin_bank_data gs101_pin_hsi2[] = {
-	EXYNOS850_PIN_BANK_EINTG(6, 0x0, "gph2", 0x00),
-	EXYNOS850_PIN_BANK_EINTG(2, 0x20, "gph3", 0x04),
-	EXYNOS850_PIN_BANK_EINTG(6, 0x40, "gph4", 0x08),
+	GS101_PIN_BANK_EINTG(6, 0x0, "gph2", 0x00, 0x00),
+	GS101_PIN_BANK_EINTG(2, 0x20, "gph3", 0x04, 0x08),
+	GS101_PIN_BANK_EINTG(6, 0x40, "gph4", 0x08, 0x0c),
 };
 
 static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = {
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h
index 7b7ff7ffeb56bdde2504ec90c8df13bdd1ace70e..33df21d5c9d61e852834031570d4a0ac0e51f6a4 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.h
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.h
@@ -175,6 +175,28 @@
 		.name			= id				\
 	}
 
+#define GS101_PIN_BANK_EINTG(pins, reg, id, offs, fltcon_offs) \
+	{							\
+		.type			= &exynos850_bank_type_off,	\
+		.pctl_offset		= reg,			\
+		.nr_pins		= pins,			\
+		.eint_type		= EINT_TYPE_GPIO,	\
+		.eint_offset		= offs,			\
+		.eint_fltcon_offset	= fltcon_offs,		\
+		.name			= id			\
+	}
+
+#define GS101_PIN_BANK_EINTW(pins, reg, id, offs, fltcon_offs) \
+	{								\
+		.type			= &exynos850_bank_type_alive,	\
+		.pctl_offset		= reg,				\
+		.nr_pins		= pins,				\
+		.eint_type		= EINT_TYPE_WKUP,		\
+		.eint_offset		= offs,				\
+		.eint_fltcon_offset	= fltcon_offs,			\
+		.name			= id				\
+	}
+
 /**
  * struct exynos_weint_data: irq specific data for all the wakeup interrupts
  * generated by the external wakeup interrupt controller.
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index cfced7afd4ca6e99c7e72a588d780f0542990ed9..963060920301ec90affb2ee6d758d3d602ffb4a9 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -1230,6 +1230,7 @@ samsung_pinctrl_get_soc_data(struct samsung_pinctrl_drv_data *d,
 		bank->eint_con_offset = bdata->eint_con_offset;
 		bank->eint_mask_offset = bdata->eint_mask_offset;
 		bank->eint_pend_offset = bdata->eint_pend_offset;
+		bank->eint_fltcon_offset = bdata->eint_fltcon_offset;
 		bank->name = bdata->name;
 
 		raw_spin_lock_init(&bank->slock);
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
index bb0689d52ea0b4392714fa9bcdcbae8d253c73a1..371e4f02bbfb375964b7833beb9bbc098a51f4a3 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.h
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
@@ -144,6 +144,7 @@ struct samsung_pin_bank_type {
  * @eint_con_offset: ExynosAuto SoC-specific EINT control register offset of bank.
  * @eint_mask_offset: ExynosAuto SoC-specific EINT mask register offset of bank.
  * @eint_pend_offset: ExynosAuto SoC-specific EINT pend register offset of bank.
+ * @eint_fltcon_offset: GS101 SoC-specific EINT filter config register offset.
  * @name: name to be prefixed for each pin in this pin bank.
  */
 struct samsung_pin_bank_data {
@@ -158,6 +159,7 @@ struct samsung_pin_bank_data {
 	u32		eint_con_offset;
 	u32		eint_mask_offset;
 	u32		eint_pend_offset;
+	u32		eint_fltcon_offset;
 	const char	*name;
 };
 
@@ -175,6 +177,7 @@ struct samsung_pin_bank_data {
  * @eint_con_offset: ExynosAuto SoC-specific EINT register or interrupt offset of bank.
  * @eint_mask_offset: ExynosAuto SoC-specific EINT mask register offset of bank.
  * @eint_pend_offset: ExynosAuto SoC-specific EINT pend register offset of bank.
+ * @eint_fltcon_offset: GS101 SoC-specific EINT filter config register offset.
  * @name: name to be prefixed for each pin in this pin bank.
  * @id: id of the bank, propagated to the pin range.
  * @pin_base: starting pin number of the bank.
@@ -201,6 +204,7 @@ struct samsung_pin_bank {
 	u32		eint_con_offset;
 	u32		eint_mask_offset;
 	u32		eint_pend_offset;
+	u32		eint_fltcon_offset;
 	const char	*name;
 	u32		id;
 

-- 
2.49.0.rc0.332.g42c0ae87b1-goog

[PATCH v3 2/4] pinctrl: samsung: add dedicated SoC eint suspend/resume callbacks

[Peter Griffin]

gs101 needs it's own suspend/resume callbacks to use the newly
added eint_fltcon_offset for saving & restoring fltcon0 & fltcon1
registers. It also differs to previous SoCs in that fltcon1
register doesn't always exist for each bank.

exynosautov920 also has dedicated logic for using eint_con_offset
and eint_mask_offset for saving & restoring it's registers.

Refactor the existing platform specific suspend/resume callback
so that each SoC variant has their own callback containing the
SoC specific logic.

Additionally we now call drvdata->suspend() & drvdata->resume()
from within the loop that iterates the banks in
samsung_pinctrl_suspend() and samsung_pinctrl_resume().

This simplifies the logic, and allows us to remove the
clk_enable() and clk_disable() from the callbacks.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
Changes since v2:
* Remove useless init (Andre)
* make it clear set_wakeup is conditional on bank->eint_type (Andre)

Changes since v1:
* Split code refactor & gs101 parts into separate patches (Andre)
---
 drivers/pinctrl/samsung/pinctrl-exynos-arm64.c |  28 ++--
 drivers/pinctrl/samsung/pinctrl-exynos.c       | 201 ++++++++++---------------
 drivers/pinctrl/samsung/pinctrl-exynos.h       |   6 +-
 drivers/pinctrl/samsung/pinctrl-samsung.c      |  11 +-
 drivers/pinctrl/samsung/pinctrl-samsung.h      |   8 +-
 5 files changed, 109 insertions(+), 145 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
index e28fe81776466b693417c66bb15752d609b79eb1..57c98d2451b54b00d50e0e948e272ed53d386c34 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
@@ -1112,8 +1112,8 @@ static const struct samsung_pin_ctrl exynosautov920_pin_ctrl[] = {
 		.pin_banks	= exynosautov920_pin_banks0,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks0),
 		.eint_wkup_init	= exynos_eint_wkup_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 		.retention_data	= &exynosautov920_retention_data,
 	}, {
 		/* pin-controller instance 1 AUD data */
@@ -1124,43 +1124,43 @@ static const struct samsung_pin_ctrl exynosautov920_pin_ctrl[] = {
 		.pin_banks	= exynosautov920_pin_banks2,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks2),
 		.eint_gpio_init	= exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 	}, {
 		/* pin-controller instance 3 HSI1 data */
 		.pin_banks	= exynosautov920_pin_banks3,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks3),
 		.eint_gpio_init	= exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 	}, {
 		/* pin-controller instance 4 HSI2 data */
 		.pin_banks	= exynosautov920_pin_banks4,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks4),
 		.eint_gpio_init	= exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 	}, {
 		/* pin-controller instance 5 HSI2UFS data */
 		.pin_banks	= exynosautov920_pin_banks5,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks5),
 		.eint_gpio_init	= exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 	}, {
 		/* pin-controller instance 6 PERIC0 data */
 		.pin_banks	= exynosautov920_pin_banks6,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks6),
 		.eint_gpio_init	= exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 	}, {
 		/* pin-controller instance 7 PERIC1 data */
 		.pin_banks	= exynosautov920_pin_banks7,
 		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks7),
 		.eint_gpio_init	= exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= exynosautov920_pinctrl_suspend,
+		.resume		= exynosautov920_pinctrl_resume,
 	},
 };
 
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index ac6dc22b37c98ed5b7fca3335764f19abb2f71cc..f10ff09c1af01c11ff9229aaef77df32eb057b7b 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -761,153 +761,114 @@ __init int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
 	return 0;
 }
 
-static void exynos_pinctrl_suspend_bank(
-				struct samsung_pinctrl_drv_data *drvdata,
-				struct samsung_pin_bank *bank)
+static void exynos_set_wakeup(struct samsung_pin_bank *bank)
 {
-	struct exynos_eint_gpio_save *save = bank->soc_priv;
-	const void __iomem *regs = bank->eint_base;
+	struct exynos_irq_chip *irq_chip;
 
-	if (clk_enable(bank->drvdata->pclk)) {
-		dev_err(bank->gpio_chip.parent,
-			"unable to enable clock for saving state\n");
-		return;
+	if (bank->irq_chip) {
+		irq_chip = bank->irq_chip;
+		irq_chip->set_eint_wakeup_mask(bank->drvdata, irq_chip);
 	}
-
-	save->eint_con = readl(regs + EXYNOS_GPIO_ECON_OFFSET
-						+ bank->eint_offset);
-	save->eint_fltcon0 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
-						+ 2 * bank->eint_offset);
-	save->eint_fltcon1 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
-						+ 2 * bank->eint_offset + 4);
-	save->eint_mask = readl(regs + bank->irq_chip->eint_mask
-						+ bank->eint_offset);
-
-	clk_disable(bank->drvdata->pclk);
-
-	pr_debug("%s: save     con %#010x\n", bank->name, save->eint_con);
-	pr_debug("%s: save fltcon0 %#010x\n", bank->name, save->eint_fltcon0);
-	pr_debug("%s: save fltcon1 %#010x\n", bank->name, save->eint_fltcon1);
-	pr_debug("%s: save    mask %#010x\n", bank->name, save->eint_mask);
 }
 
-static void exynosauto_pinctrl_suspend_bank(struct samsung_pinctrl_drv_data *drvdata,
-					    struct samsung_pin_bank *bank)
+void exynos_pinctrl_suspend(struct samsung_pin_bank *bank)
 {
 	struct exynos_eint_gpio_save *save = bank->soc_priv;
 	const void __iomem *regs = bank->eint_base;
 
-	if (clk_enable(bank->drvdata->pclk)) {
-		dev_err(bank->gpio_chip.parent,
-			"unable to enable clock for saving state\n");
-		return;
-	}
-
-	save->eint_con = readl(regs + bank->pctl_offset + bank->eint_con_offset);
-	save->eint_mask = readl(regs + bank->pctl_offset + bank->eint_mask_offset);
-
-	clk_disable(bank->drvdata->pclk);
-
-	pr_debug("%s: save     con %#010x\n", bank->name, save->eint_con);
-	pr_debug("%s: save    mask %#010x\n", bank->name, save->eint_mask);
+	if (bank->eint_type == EINT_TYPE_GPIO) {
+		save->eint_con = readl(regs + EXYNOS_GPIO_ECON_OFFSET
+				       + bank->eint_offset);
+		save->eint_fltcon0 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+					   + 2 * bank->eint_offset);
+		save->eint_fltcon1 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+					   + 2 * bank->eint_offset + 4);
+		save->eint_mask = readl(regs + bank->irq_chip->eint_mask
+					+ bank->eint_offset);
+
+		pr_debug("%s: save     con %#010x\n",
+			 bank->name, save->eint_con);
+		pr_debug("%s: save fltcon0 %#010x\n",
+			 bank->name, save->eint_fltcon0);
+		pr_debug("%s: save fltcon1 %#010x\n",
+			 bank->name, save->eint_fltcon1);
+		pr_debug("%s: save    mask %#010x\n",
+			 bank->name, save->eint_mask);
+	} else if (bank->eint_type == EINT_TYPE_WKUP)
+		exynos_set_wakeup(bank);
 }
 
-void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata)
+void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank)
 {
-	struct samsung_pin_bank *bank = drvdata->pin_banks;
-	struct exynos_irq_chip *irq_chip = NULL;
-	int i;
+	struct exynos_eint_gpio_save *save = bank->soc_priv;
+	const void __iomem *regs = bank->eint_base;
 
-	for (i = 0; i < drvdata->nr_banks; ++i, ++bank) {
-		if (bank->eint_type == EINT_TYPE_GPIO) {
-			if (bank->eint_con_offset)
-				exynosauto_pinctrl_suspend_bank(drvdata, bank);
-			else
-				exynos_pinctrl_suspend_bank(drvdata, bank);
-		}
-		else if (bank->eint_type == EINT_TYPE_WKUP) {
-			if (!irq_chip) {
-				irq_chip = bank->irq_chip;
-				irq_chip->set_eint_wakeup_mask(drvdata,
-							       irq_chip);
-			}
-		}
-	}
+	if (bank->eint_type == EINT_TYPE_GPIO) {
+		save->eint_con = readl(regs + bank->pctl_offset +
+				       bank->eint_con_offset);
+		save->eint_mask = readl(regs + bank->pctl_offset +
+					bank->eint_mask_offset);
+		pr_debug("%s: save     con %#010x\n",
+			 bank->name, save->eint_con);
+		pr_debug("%s: save    mask %#010x\n",
+			 bank->name, save->eint_mask);
+	} else if (bank->eint_type == EINT_TYPE_WKUP)
+		exynos_set_wakeup(bank);
 }
 
-static void exynos_pinctrl_resume_bank(
-				struct samsung_pinctrl_drv_data *drvdata,
-				struct samsung_pin_bank *bank)
+void exynos_pinctrl_resume(struct samsung_pin_bank *bank)
 {
 	struct exynos_eint_gpio_save *save = bank->soc_priv;
 	void __iomem *regs = bank->eint_base;
 
-	if (clk_enable(bank->drvdata->pclk)) {
-		dev_err(bank->gpio_chip.parent,
-			"unable to enable clock for restoring state\n");
-		return;
+	if (bank->eint_type == EINT_TYPE_GPIO) {
+		pr_debug("%s:     con %#010x => %#010x\n", bank->name,
+			 readl(regs + EXYNOS_GPIO_ECON_OFFSET
+			       + bank->eint_offset), save->eint_con);
+		pr_debug("%s: fltcon0 %#010x => %#010x\n", bank->name,
+			 readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+			       + 2 * bank->eint_offset), save->eint_fltcon0);
+		pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
+			 readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+			       + 2 * bank->eint_offset + 4),
+			       save->eint_fltcon1);
+		pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
+			 readl(regs + bank->irq_chip->eint_mask
+			       + bank->eint_offset), save->eint_mask);
+
+		writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
+		       + bank->eint_offset);
+		writel(save->eint_fltcon0, regs + EXYNOS_GPIO_EFLTCON_OFFSET
+		       + 2 * bank->eint_offset);
+		writel(save->eint_fltcon1, regs + EXYNOS_GPIO_EFLTCON_OFFSET
+		       + 2 * bank->eint_offset + 4);
+		writel(save->eint_mask, regs + bank->irq_chip->eint_mask
+		       + bank->eint_offset);
 	}
-
-	pr_debug("%s:     con %#010x => %#010x\n", bank->name,
-			readl(regs + EXYNOS_GPIO_ECON_OFFSET
-			+ bank->eint_offset), save->eint_con);
-	pr_debug("%s: fltcon0 %#010x => %#010x\n", bank->name,
-			readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
-			+ 2 * bank->eint_offset), save->eint_fltcon0);
-	pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
-			readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
-			+ 2 * bank->eint_offset + 4), save->eint_fltcon1);
-	pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
-			readl(regs + bank->irq_chip->eint_mask
-			+ bank->eint_offset), save->eint_mask);
-
-	writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
-						+ bank->eint_offset);
-	writel(save->eint_fltcon0, regs + EXYNOS_GPIO_EFLTCON_OFFSET
-						+ 2 * bank->eint_offset);
-	writel(save->eint_fltcon1, regs + EXYNOS_GPIO_EFLTCON_OFFSET
-						+ 2 * bank->eint_offset + 4);
-	writel(save->eint_mask, regs + bank->irq_chip->eint_mask
-						+ bank->eint_offset);
-
-	clk_disable(bank->drvdata->pclk);
 }
 
-static void exynosauto_pinctrl_resume_bank(struct samsung_pinctrl_drv_data *drvdata,
-					   struct samsung_pin_bank *bank)
+void exynosautov920_pinctrl_resume(struct samsung_pin_bank *bank)
 {
 	struct exynos_eint_gpio_save *save = bank->soc_priv;
 	void __iomem *regs = bank->eint_base;
 
-	if (clk_enable(bank->drvdata->pclk)) {
-		dev_err(bank->gpio_chip.parent,
-			"unable to enable clock for restoring state\n");
-		return;
+	if (bank->eint_type == EINT_TYPE_GPIO) {
+		/* exynosautov920 has eint_con_offset for all but one bank */
+		if (!bank->eint_con_offset)
+			exynos_pinctrl_resume(bank);
+
+		pr_debug("%s:     con %#010x => %#010x\n", bank->name,
+			 readl(regs + bank->pctl_offset + bank->eint_con_offset),
+			       save->eint_con);
+		pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
+			 readl(regs + bank->pctl_offset +
+			       bank->eint_mask_offset), save->eint_mask);
+
+		writel(save->eint_con,
+		       regs + bank->pctl_offset + bank->eint_con_offset);
+		writel(save->eint_mask,
+		       regs + bank->pctl_offset + bank->eint_mask_offset);
 	}
-
-	pr_debug("%s:     con %#010x => %#010x\n", bank->name,
-		 readl(regs + bank->pctl_offset + bank->eint_con_offset), save->eint_con);
-	pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
-		 readl(regs + bank->pctl_offset + bank->eint_mask_offset), save->eint_mask);
-
-	writel(save->eint_con, regs + bank->pctl_offset + bank->eint_con_offset);
-	writel(save->eint_mask, regs + bank->pctl_offset + bank->eint_mask_offset);
-
-	clk_disable(bank->drvdata->pclk);
-}
-
-void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
-{
-	struct samsung_pin_bank *bank = drvdata->pin_banks;
-	int i;
-
-	for (i = 0; i < drvdata->nr_banks; ++i, ++bank)
-		if (bank->eint_type == EINT_TYPE_GPIO) {
-			if (bank->eint_con_offset)
-				exynosauto_pinctrl_resume_bank(drvdata, bank);
-			else
-				exynos_pinctrl_resume_bank(drvdata, bank);
-		}
 }
 
 static void exynos_retention_enable(struct samsung_pinctrl_drv_data *drvdata)
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h
index 33df21d5c9d61e852834031570d4a0ac0e51f6a4..35c2bc4ea488bda600ebfbda1492f5f49dbd9849 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.h
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.h
@@ -221,8 +221,10 @@ struct exynos_muxed_weint_data {
 
 int exynos_eint_gpio_init(struct samsung_pinctrl_drv_data *d);
 int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d);
-void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata);
-void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata);
+void exynosautov920_pinctrl_resume(struct samsung_pin_bank *bank);
+void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank);
+void exynos_pinctrl_suspend(struct samsung_pin_bank *bank);
+void exynos_pinctrl_resume(struct samsung_pin_bank *bank);
 struct samsung_retention_ctrl *
 exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
 		      const struct samsung_retention_data *data);
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 963060920301ec90affb2ee6d758d3d602ffb4a9..375634d8cc79d6533603e3eed562452181e2ee25 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -1349,6 +1349,9 @@ static int __maybe_unused samsung_pinctrl_suspend(struct device *dev)
 		const u8 *widths = bank->type->fld_width;
 		enum pincfg_type type;
 
+		if (drvdata->suspend)
+			drvdata->suspend(bank);
+
 		/* Registers without a powerdown config aren't lost */
 		if (!widths[PINCFG_TYPE_CON_PDN])
 			continue;
@@ -1373,8 +1376,6 @@ static int __maybe_unused samsung_pinctrl_suspend(struct device *dev)
 
 	clk_disable(drvdata->pclk);
 
-	if (drvdata->suspend)
-		drvdata->suspend(drvdata);
 	if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
 		drvdata->retention_ctrl->enable(drvdata);
 
@@ -1406,9 +1407,6 @@ static int __maybe_unused samsung_pinctrl_resume(struct device *dev)
 		return ret;
 	}
 
-	if (drvdata->resume)
-		drvdata->resume(drvdata);
-
 	for (i = 0; i < drvdata->nr_banks; i++) {
 		struct samsung_pin_bank *bank = &drvdata->pin_banks[i];
 		void __iomem *reg = bank->pctl_base + bank->pctl_offset;
@@ -1416,6 +1414,9 @@ static int __maybe_unused samsung_pinctrl_resume(struct device *dev)
 		const u8 *widths = bank->type->fld_width;
 		enum pincfg_type type;
 
+		if (drvdata->resume)
+			drvdata->resume(bank);
+
 		/* Registers without a powerdown config aren't lost */
 		if (!widths[PINCFG_TYPE_CON_PDN])
 			continue;
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
index 371e4f02bbfb375964b7833beb9bbc098a51f4a3..e939e5bb0347458ae4a9014fd9657fc59c5c3994 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.h
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
@@ -285,8 +285,8 @@ struct samsung_pin_ctrl {
 	int		(*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
 	int		(*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
 	void		(*pud_value_init)(struct samsung_pinctrl_drv_data *drvdata);
-	void		(*suspend)(struct samsung_pinctrl_drv_data *);
-	void		(*resume)(struct samsung_pinctrl_drv_data *);
+	void		(*suspend)(struct samsung_pin_bank *bank);
+	void		(*resume)(struct samsung_pin_bank *bank);
 };
 
 /**
@@ -335,8 +335,8 @@ struct samsung_pinctrl_drv_data {
 
 	struct samsung_retention_ctrl	*retention_ctrl;
 
-	void (*suspend)(struct samsung_pinctrl_drv_data *);
-	void (*resume)(struct samsung_pinctrl_drv_data *);
+	void (*suspend)(struct samsung_pin_bank *bank);
+	void (*resume)(struct samsung_pin_bank *bank);
 };
 
 /**

-- 
2.49.0.rc0.332.g42c0ae87b1-goog

[PATCH v3 3/4] pinctrl: samsung: add gs101 specific eint suspend/resume callbacks

[Peter Griffin]

gs101 differs to other SoCs in that fltcon1 register doesn't
always exist. Additionally the offset of fltcon0 is not fixed
and needs to use the newly added eint_fltcon_offset variable.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Fixes: 4a8be01a1a7a ("pinctrl: samsung: Add gs101 SoC pinctrl configuration")
Cc: stable@vger.kernel.org
---
Changes since v2:
* make it clear exynos_set_wakeup(bank) is conditional on bank type (Andre)
* align style where the '+' is placed (Andre)
* remove unnecessary braces (Andre)
---
 drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 24 ++++-----
 drivers/pinctrl/samsung/pinctrl-exynos.c       | 70 ++++++++++++++++++++++++++
 drivers/pinctrl/samsung/pinctrl-exynos.h       |  2 +
 3 files changed, 84 insertions(+), 12 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
index 57c98d2451b54b00d50e0e948e272ed53d386c34..fca447ebc5f5956b7e8d2f2d08f23622095b1ee6 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
@@ -1455,15 +1455,15 @@ static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = {
 		.pin_banks	= gs101_pin_alive,
 		.nr_banks	= ARRAY_SIZE(gs101_pin_alive),
 		.eint_wkup_init = exynos_eint_wkup_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= gs101_pinctrl_suspend,
+		.resume		= gs101_pinctrl_resume,
 	}, {
 		/* pin banks of gs101 pin-controller (FAR_ALIVE) */
 		.pin_banks	= gs101_pin_far_alive,
 		.nr_banks	= ARRAY_SIZE(gs101_pin_far_alive),
 		.eint_wkup_init = exynos_eint_wkup_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= gs101_pinctrl_suspend,
+		.resume		= gs101_pinctrl_resume,
 	}, {
 		/* pin banks of gs101 pin-controller (GSACORE) */
 		.pin_banks	= gs101_pin_gsacore,
@@ -1477,29 +1477,29 @@ static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = {
 		.pin_banks	= gs101_pin_peric0,
 		.nr_banks	= ARRAY_SIZE(gs101_pin_peric0),
 		.eint_gpio_init = exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= gs101_pinctrl_suspend,
+		.resume		= gs101_pinctrl_resume,
 	}, {
 		/* pin banks of gs101 pin-controller (PERIC1) */
 		.pin_banks	= gs101_pin_peric1,
 		.nr_banks	= ARRAY_SIZE(gs101_pin_peric1),
 		.eint_gpio_init = exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume	= exynos_pinctrl_resume,
+		.suspend	= gs101_pinctrl_suspend,
+		.resume		= gs101_pinctrl_resume,
 	}, {
 		/* pin banks of gs101 pin-controller (HSI1) */
 		.pin_banks	= gs101_pin_hsi1,
 		.nr_banks	= ARRAY_SIZE(gs101_pin_hsi1),
 		.eint_gpio_init = exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= gs101_pinctrl_suspend,
+		.resume		= gs101_pinctrl_resume,
 	}, {
 		/* pin banks of gs101 pin-controller (HSI2) */
 		.pin_banks	= gs101_pin_hsi2,
 		.nr_banks	= ARRAY_SIZE(gs101_pin_hsi2),
 		.eint_gpio_init = exynos_eint_gpio_init,
-		.suspend	= exynos_pinctrl_suspend,
-		.resume		= exynos_pinctrl_resume,
+		.suspend	= gs101_pinctrl_suspend,
+		.resume		= gs101_pinctrl_resume,
 	},
 };
 
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index f10ff09c1af01c11ff9229aaef77df32eb057b7b..9cffbe9ee64aa5236026978ac2466b709da5bffc 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -798,6 +798,40 @@ void exynos_pinctrl_suspend(struct samsung_pin_bank *bank)
 		exynos_set_wakeup(bank);
 }
 
+void gs101_pinctrl_suspend(struct samsung_pin_bank *bank)
+{
+	struct exynos_eint_gpio_save *save = bank->soc_priv;
+	const void __iomem *regs = bank->eint_base;
+
+	if (bank->eint_type == EINT_TYPE_GPIO) {
+		save->eint_con = readl(regs + EXYNOS_GPIO_ECON_OFFSET
+				       + bank->eint_offset);
+
+		save->eint_fltcon0 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
+					   + bank->eint_fltcon_offset);
+
+		/* fltcon1 register only exists for pins 4-7 */
+		if (bank->nr_pins > 4)
+			save->eint_fltcon1 = readl(regs +
+						EXYNOS_GPIO_EFLTCON_OFFSET
+						+ bank->eint_fltcon_offset + 4);
+
+		save->eint_mask = readl(regs + bank->irq_chip->eint_mask
+					+ bank->eint_offset);
+
+		pr_debug("%s: save     con %#010x\n",
+			 bank->name, save->eint_con);
+		pr_debug("%s: save fltcon0 %#010x\n",
+			 bank->name, save->eint_fltcon0);
+		if (bank->nr_pins > 4)
+			pr_debug("%s: save fltcon1 %#010x\n",
+				 bank->name, save->eint_fltcon1);
+		pr_debug("%s: save    mask %#010x\n",
+			 bank->name, save->eint_mask);
+	} else if (bank->eint_type == EINT_TYPE_WKUP)
+		exynos_set_wakeup(bank);
+}
+
 void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank)
 {
 	struct exynos_eint_gpio_save *save = bank->soc_priv;
@@ -816,6 +850,42 @@ void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank)
 		exynos_set_wakeup(bank);
 }
 
+void gs101_pinctrl_resume(struct samsung_pin_bank *bank)
+{
+	struct exynos_eint_gpio_save *save = bank->soc_priv;
+
+	void __iomem *regs = bank->eint_base;
+	void __iomem *eint_fltcfg0 = regs + EXYNOS_GPIO_EFLTCON_OFFSET
+		     + bank->eint_fltcon_offset;
+
+	if (bank->eint_type == EINT_TYPE_GPIO) {
+		pr_debug("%s:     con %#010x => %#010x\n", bank->name,
+			 readl(regs + EXYNOS_GPIO_ECON_OFFSET
+			       + bank->eint_offset), save->eint_con);
+
+		pr_debug("%s: fltcon0 %#010x => %#010x\n", bank->name,
+			 readl(eint_fltcfg0), save->eint_fltcon0);
+
+		/* fltcon1 register only exists for pins 4-7 */
+		if (bank->nr_pins > 4)
+			pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
+				 readl(eint_fltcfg0 + 4), save->eint_fltcon1);
+
+		pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
+			 readl(regs + bank->irq_chip->eint_mask
+			       + bank->eint_offset), save->eint_mask);
+
+		writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
+		       + bank->eint_offset);
+		writel(save->eint_fltcon0, eint_fltcfg0);
+
+		if (bank->nr_pins > 4)
+			writel(save->eint_fltcon1, eint_fltcfg0 + 4);
+		writel(save->eint_mask, regs + bank->irq_chip->eint_mask
+		       + bank->eint_offset);
+	}
+}
+
 void exynos_pinctrl_resume(struct samsung_pin_bank *bank)
 {
 	struct exynos_eint_gpio_save *save = bank->soc_priv;
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h
index 35c2bc4ea488bda600ebfbda1492f5f49dbd9849..773f161a82a38cbaad05fcbc09a936300f5c7595 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.h
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.h
@@ -225,6 +225,8 @@ void exynosautov920_pinctrl_resume(struct samsung_pin_bank *bank);
 void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank);
 void exynos_pinctrl_suspend(struct samsung_pin_bank *bank);
 void exynos_pinctrl_resume(struct samsung_pin_bank *bank);
+void gs101_pinctrl_suspend(struct samsung_pin_bank *bank);
+void gs101_pinctrl_resume(struct samsung_pin_bank *bank);
 struct samsung_retention_ctrl *
 exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
 		      const struct samsung_retention_data *data);

-- 
2.49.0.rc0.332.g42c0ae87b1-goog

[PATCH v3 4/4] pinctrl: samsung: Add filter selection support for alive bank on gs101

[Peter Griffin]

Newer Exynos based SoCs have a filter selection bitfield in the filter
configuration registers on alive bank pins. This allows the selection of
a digital or analog delay filter for each pin. Add support for selecting
and enabling the filter.

On suspend we set the analog filter to all pins in the bank (as the
digital filter relies on a clock). On resume the digital filter is
reapplied to all pins in the bank. The digital filter is working via
a clock and has an adjustable filter delay flt_width bitfield, whereas
the analog filter uses a fixed delay.

The filter determines to what extent signal fluctuations received through
the pad are considered glitches.

The code path can be exercised using
echo mem > /sys/power/state
And then wake the device using a eint gpio

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---

Changes since v2:
* Ensure EXYNOS_FLTCON_DIGITAL bit is cleared (Andre)
* Make it obvious that exynos_eint_set_filter() is conditional on bank type (Andre)

Changes since v1:
* Remove eint_flt_selectable bool as it can be deduced from EINT_TYPE_WKUP (Peter)
* Move filter config comment to header (Andre)
* Rename EXYNOS_FLTCON_DELAY to EXYNOS_FLTCON_ANALOG (Andre)
* Remove misleading old comment (Andre)
* Refactor exynos_eint_update_flt_reg() into a loop (Andre)

Note: this patch was previously sent as part of the initial gs101/ Pixel 6
series and was dropped in v6. This new version incorporates the review
feedback from Sam Protsenko here in v5.

Link: https://lore.kernel.org/all/20231201160925.3136868-1-peter.griffin@linaro.org/T/#m79ced98939e895c840d812c8b4c2b3f33ce604c8

Changes since previous version
* Drop fltcon_type enum and use bool eint_flt_selectable (Sam)
* Refactor and add exynos_eint_update_flt_reg() (Sam)
* Rename function to exynos_eint_set_filter() for easier readability (Sam)
* Remove comments and `if bank->fltcon_type != FLT_DEFAULT)` checks and indentation (Sam)
---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 37 +++++++++++++++++++++++++++++++-
 drivers/pinctrl/samsung/pinctrl-exynos.h | 20 +++++++++++++++++
 2 files changed, 56 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 9cffbe9ee64aa5236026978ac2466b709da5bffc..1176efc0ef0464d1a6fc70b0a04f5ddd73ef88a4 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -369,6 +369,37 @@ struct exynos_eint_gpio_save {
 	u32 eint_mask;
 };
 
+static void exynos_eint_update_flt_reg(void __iomem *reg, int cnt, int con)
+{
+	unsigned int val, shift;
+	int i;
+
+	val = readl(reg);
+	for (i = 0; i < cnt; i++) {
+		shift = i * EXYNOS_FLTCON_LEN;
+		val &= ~(EXYNOS_FLTCON_DIGITAL << shift);
+		val |= con << shift;
+	}
+	writel(val, reg);
+}
+
+/*
+ * Set the desired filter (digital or analog delay) and enable it to
+ * every pin in the bank. Note the filter selection bitfield is only
+ * found on alive banks. The filter determines to what extent signal
+ * fluctuations received through the pad are considered glitches.
+ */
+static void exynos_eint_set_filter(struct samsung_pin_bank *bank, int filter)
+{
+	unsigned int off = EXYNOS_GPIO_EFLTCON_OFFSET + bank->eint_fltcon_offset;
+	void __iomem *reg = bank->drvdata->virt_base + off;
+	unsigned int con = EXYNOS_FLTCON_EN | filter;
+
+	for (int n = 0; n < bank->nr_pins; n += 4)
+		exynos_eint_update_flt_reg(reg + n,
+					   min(bank->nr_pins - n, 4), con);
+}
+
 /*
  * exynos_eint_gpio_init() - setup handling of external gpio interrupts.
  * @d: driver data of samsung pinctrl driver.
@@ -828,8 +859,10 @@ void gs101_pinctrl_suspend(struct samsung_pin_bank *bank)
 				 bank->name, save->eint_fltcon1);
 		pr_debug("%s: save    mask %#010x\n",
 			 bank->name, save->eint_mask);
-	} else if (bank->eint_type == EINT_TYPE_WKUP)
+	} else if (bank->eint_type == EINT_TYPE_WKUP) {
 		exynos_set_wakeup(bank);
+		exynos_eint_set_filter(bank, EXYNOS_FLTCON_ANALOG);
+	}
 }
 
 void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank)
@@ -883,6 +916,8 @@ void gs101_pinctrl_resume(struct samsung_pin_bank *bank)
 			writel(save->eint_fltcon1, eint_fltcfg0 + 4);
 		writel(save->eint_mask, regs + bank->irq_chip->eint_mask
 		       + bank->eint_offset);
+	} else if (bank->eint_type == EINT_TYPE_WKUP) {
+		exynos_eint_set_filter(bank, EXYNOS_FLTCON_DIGITAL);
 	}
 }
 
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h
index 773f161a82a38cbaad05fcbc09a936300f5c7595..66acbd08d3445ca6ee7358d3c4a6cb2be5d82842 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.h
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.h
@@ -52,6 +52,26 @@
 #define EXYNOS_EINT_MAX_PER_BANK	8
 #define EXYNOS_EINT_NR_WKUP_EINT
 
+/*
+ * EINT filter configuration register (on alive banks) has
+ * the following layout.
+ *
+ * BitfieldName[PinNum][Bit:Bit]
+ * FLT_EN[3][31] FLT_SEL[3][30] FLT_WIDTH[3][29:24]
+ * FLT_EN[2][23] FLT_SEL[2][22] FLT_WIDTH[2][21:16]
+ * FLT_EN[1][15] FLT_SEL[1][14] FLT_WIDTH[1][13:8]
+ * FLT_EN[0][7]  FLT_SEL[0][6]  FLT_WIDTH[0][5:0]
+ *
+ * FLT_EN	0x0 = Disable, 0x1=Enable
+ * FLT_SEL	0x0 = Analog delay filter, 0x1 Digital filter (clock count)
+ * FLT_WIDTH	Filtering width. Valid when FLT_SEL is 0x1
+ */
+
+#define EXYNOS_FLTCON_EN		BIT(7)
+#define EXYNOS_FLTCON_DIGITAL		BIT(6)
+#define EXYNOS_FLTCON_ANALOG		(0 << 6)
+#define EXYNOS_FLTCON_LEN		8
+
 #define EXYNOS_PIN_BANK_EINTN(pins, reg, id)		\
 	{						\
 		.type		= &bank_type_off,	\

-- 
2.49.0.rc0.332.g42c0ae87b1-goog

Re: [PATCH v3 2/4] pinctrl: samsung: add dedicated SoC eint suspend/resume callbacks

[André Draszik]

On Thu, 2025-03-06 at 20:42 +0000, Peter Griffin wrote:
> gs101 needs it's own suspend/resume callbacks to use the newly
> added eint_fltcon_offset for saving & restoring fltcon0 & fltcon1
> registers. It also differs to previous SoCs in that fltcon1
> register doesn't always exist for each bank.
> 
> exynosautov920 also has dedicated logic for using eint_con_offset
> and eint_mask_offset for saving & restoring it's registers.
> 
> Refactor the existing platform specific suspend/resume callback
> so that each SoC variant has their own callback containing the
> SoC specific logic.
> 
> Additionally we now call drvdata->suspend() & drvdata->resume()
> from within the loop that iterates the banks in
> samsung_pinctrl_suspend() and samsung_pinctrl_resume().
> 
> This simplifies the logic, and allows us to remove the
> clk_enable() and clk_disable() from the callbacks.
> 
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> ---
> Changes since v2:
> * Remove useless init (Andre)
> * make it clear set_wakeup is conditional on bank->eint_type (Andre)
> 
> Changes since v1:
> * Split code refactor & gs101 parts into separate patches (Andre)
> ---
>  drivers/pinctrl/samsung/pinctrl-exynos-arm64.c |  28 ++--
>  drivers/pinctrl/samsung/pinctrl-exynos.c       | 201 ++++++++++---------------
>  drivers/pinctrl/samsung/pinctrl-exynos.h       |   6 +-
>  drivers/pinctrl/samsung/pinctrl-samsung.c      |  11 +-
>  drivers/pinctrl/samsung/pinctrl-samsung.h      |   8 +-
>  5 files changed, 109 insertions(+), 145 deletions(-)

Reviewed-by: André Draszik <andre.draszik@linaro.org>

Re: [PATCH v3 4/4] pinctrl: samsung: Add filter selection support for alive bank on gs101

[André Draszik]

On Thu, 2025-03-06 at 20:42 +0000, Peter Griffin wrote:
> Newer Exynos based SoCs have a filter selection bitfield in the filter
> configuration registers on alive bank pins. This allows the selection of
> a digital or analog delay filter for each pin. Add support for selecting
> and enabling the filter.
> 
> On suspend we set the analog filter to all pins in the bank (as the
> digital filter relies on a clock). On resume the digital filter is
> reapplied to all pins in the bank. The digital filter is working via
> a clock and has an adjustable filter delay flt_width bitfield, whereas
> the analog filter uses a fixed delay.
> 
> The filter determines to what extent signal fluctuations received through
> the pad are considered glitches.
> 
> The code path can be exercised using
> echo mem > /sys/power/state
> And then wake the device using a eint gpio
> 
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

Reviewed-by: André Draszik <andre.draszik@linaro.org>

Re: [PATCH v3 3/4] pinctrl: samsung: add gs101 specific eint suspend/resume callbacks

[André Draszik]

On Thu, 2025-03-06 at 20:42 +0000, Peter Griffin wrote:
> gs101 differs to other SoCs in that fltcon1 register doesn't
> always exist. Additionally the offset of fltcon0 is not fixed
> and needs to use the newly added eint_fltcon_offset variable.
> 
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> Fixes: 4a8be01a1a7a ("pinctrl: samsung: Add gs101 SoC pinctrl configuration")
> Cc: stable@vger.kernel.org
> ---
> Changes since v2:
> * make it clear exynos_set_wakeup(bank) is conditional on bank type (Andre)
> * align style where the '+' is placed (Andre)
> * remove unnecessary braces (Andre)
> ---
>  drivers/pinctrl/samsung/pinctrl-exynos-arm64.c | 24 ++++-----
>  drivers/pinctrl/samsung/pinctrl-exynos.c       | 70 ++++++++++++++++++++++++++
>  drivers/pinctrl/samsung/pinctrl-exynos.h       |  2 +
>  3 files changed, 84 insertions(+), 12 deletions(-)

Reviewed-by: André Draszik <andre.draszik@linaro.org>

Re: [PATCH v3 2/4] pinctrl: samsung: add dedicated SoC eint suspend/resume callbacks

[André Draszik]

On Thu, 2025-03-06 at 20:42 +0000, Peter Griffin wrote:
> gs101 needs it's own suspend/resume callbacks to use the newly
> added eint_fltcon_offset for saving & restoring fltcon0 & fltcon1
> registers. It also differs to previous SoCs in that fltcon1
> register doesn't always exist for each bank.
> 
> exynosautov920 also has dedicated logic for using eint_con_offset
> and eint_mask_offset for saving & restoring it's registers.
> 
> Refactor the existing platform specific suspend/resume callback
> so that each SoC variant has their own callback containing the
> SoC specific logic.
> 
> Additionally we now call drvdata->suspend() & drvdata->resume()
> from within the loop that iterates the banks in
> samsung_pinctrl_suspend() and samsung_pinctrl_resume().
> 
> This simplifies the logic, and allows us to remove the
> clk_enable() and clk_disable() from the callbacks.
> 
> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> ---
> Changes since v2:
> * Remove useless init (Andre)
> * make it clear set_wakeup is conditional on bank->eint_type (Andre)

I think you missed
https://lore.kernel.org/all/4f91fe1c5eed00e58a3587bceaef3e5e2a1124cf.camel@linaro.org/

See below

> Changes since v1:
> * Split code refactor & gs101 parts into separate patches (Andre)
> ---
>  drivers/pinctrl/samsung/pinctrl-exynos-arm64.c |  28 ++--
>  drivers/pinctrl/samsung/pinctrl-exynos.c       | 201 ++++++++++---------------
>  drivers/pinctrl/samsung/pinctrl-exynos.h       |   6 +-
>  drivers/pinctrl/samsung/pinctrl-samsung.c      |  11 +-
>  drivers/pinctrl/samsung/pinctrl-samsung.h      |   8 +-
>  5 files changed, 109 insertions(+), 145 deletions(-)
> 
> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> index e28fe81776466b693417c66bb15752d609b79eb1..57c98d2451b54b00d50e0e948e272ed53d386c34 100644
> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c
> @@ -1112,8 +1112,8 @@ static const struct samsung_pin_ctrl exynosautov920_pin_ctrl[] = {
>  		.pin_banks	= exynosautov920_pin_banks0,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks0),
>  		.eint_wkup_init	= exynos_eint_wkup_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  		.retention_data	= &exynosautov920_retention_data,
>  	}, {
>  		/* pin-controller instance 1 AUD data */
> @@ -1124,43 +1124,43 @@ static const struct samsung_pin_ctrl exynosautov920_pin_ctrl[] = {
>  		.pin_banks	= exynosautov920_pin_banks2,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks2),
>  		.eint_gpio_init	= exynos_eint_gpio_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  	}, {
>  		/* pin-controller instance 3 HSI1 data */
>  		.pin_banks	= exynosautov920_pin_banks3,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks3),
>  		.eint_gpio_init	= exynos_eint_gpio_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  	}, {
>  		/* pin-controller instance 4 HSI2 data */
>  		.pin_banks	= exynosautov920_pin_banks4,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks4),
>  		.eint_gpio_init	= exynos_eint_gpio_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  	}, {
>  		/* pin-controller instance 5 HSI2UFS data */
>  		.pin_banks	= exynosautov920_pin_banks5,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks5),
>  		.eint_gpio_init	= exynos_eint_gpio_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  	}, {
>  		/* pin-controller instance 6 PERIC0 data */
>  		.pin_banks	= exynosautov920_pin_banks6,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks6),
>  		.eint_gpio_init	= exynos_eint_gpio_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  	}, {
>  		/* pin-controller instance 7 PERIC1 data */
>  		.pin_banks	= exynosautov920_pin_banks7,
>  		.nr_banks	= ARRAY_SIZE(exynosautov920_pin_banks7),
>  		.eint_gpio_init	= exynos_eint_gpio_init,
> -		.suspend	= exynos_pinctrl_suspend,
> -		.resume		= exynos_pinctrl_resume,
> +		.suspend	= exynosautov920_pinctrl_suspend,
> +		.resume		= exynosautov920_pinctrl_resume,
>  	},
>  };
>  
> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
> index ac6dc22b37c98ed5b7fca3335764f19abb2f71cc..f10ff09c1af01c11ff9229aaef77df32eb057b7b 100644
> --- a/drivers/pinctrl/samsung/pinctrl-exynos.c
> +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
> @@ -761,153 +761,114 @@ __init int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
>  	return 0;
>  }
>  
> -static void exynos_pinctrl_suspend_bank(
> -				struct samsung_pinctrl_drv_data *drvdata,
> -				struct samsung_pin_bank *bank)
> +static void exynos_set_wakeup(struct samsung_pin_bank *bank)
>  {
> -	struct exynos_eint_gpio_save *save = bank->soc_priv;
> -	const void __iomem *regs = bank->eint_base;
> +	struct exynos_irq_chip *irq_chip;
>  
> -	if (clk_enable(bank->drvdata->pclk)) {
> -		dev_err(bank->gpio_chip.parent,
> -			"unable to enable clock for saving state\n");
> -		return;
> +	if (bank->irq_chip) {
> +		irq_chip = bank->irq_chip;
> +		irq_chip->set_eint_wakeup_mask(bank->drvdata, irq_chip);
>  	}
> -
> -	save->eint_con = readl(regs + EXYNOS_GPIO_ECON_OFFSET
> -						+ bank->eint_offset);
> -	save->eint_fltcon0 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> -						+ 2 * bank->eint_offset);
> -	save->eint_fltcon1 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> -						+ 2 * bank->eint_offset + 4);
> -	save->eint_mask = readl(regs + bank->irq_chip->eint_mask
> -						+ bank->eint_offset);
> -
> -	clk_disable(bank->drvdata->pclk);
> -
> -	pr_debug("%s: save     con %#010x\n", bank->name, save->eint_con);
> -	pr_debug("%s: save fltcon0 %#010x\n", bank->name, save->eint_fltcon0);
> -	pr_debug("%s: save fltcon1 %#010x\n", bank->name, save->eint_fltcon1);
> -	pr_debug("%s: save    mask %#010x\n", bank->name, save->eint_mask);
>  }
>  
> -static void exynosauto_pinctrl_suspend_bank(struct samsung_pinctrl_drv_data *drvdata,
> -					    struct samsung_pin_bank *bank)
> +void exynos_pinctrl_suspend(struct samsung_pin_bank *bank)
>  {
>  	struct exynos_eint_gpio_save *save = bank->soc_priv;
>  	const void __iomem *regs = bank->eint_base;
>  
> -	if (clk_enable(bank->drvdata->pclk)) {
> -		dev_err(bank->gpio_chip.parent,
> -			"unable to enable clock for saving state\n");
> -		return;
> -	}
> -
> -	save->eint_con = readl(regs + bank->pctl_offset + bank->eint_con_offset);
> -	save->eint_mask = readl(regs + bank->pctl_offset + bank->eint_mask_offset);
> -
> -	clk_disable(bank->drvdata->pclk);
> -
> -	pr_debug("%s: save     con %#010x\n", bank->name, save->eint_con);
> -	pr_debug("%s: save    mask %#010x\n", bank->name, save->eint_mask);
> +	if (bank->eint_type == EINT_TYPE_GPIO) {
> +		save->eint_con = readl(regs + EXYNOS_GPIO_ECON_OFFSET
> +				       + bank->eint_offset);
> +		save->eint_fltcon0 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> +					   + 2 * bank->eint_offset);
> +		save->eint_fltcon1 = readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> +					   + 2 * bank->eint_offset + 4);
> +		save->eint_mask = readl(regs + bank->irq_chip->eint_mask
> +					+ bank->eint_offset);
> +
> +		pr_debug("%s: save     con %#010x\n",
> +			 bank->name, save->eint_con);
> +		pr_debug("%s: save fltcon0 %#010x\n",
> +			 bank->name, save->eint_fltcon0);
> +		pr_debug("%s: save fltcon1 %#010x\n",
> +			 bank->name, save->eint_fltcon1);
> +		pr_debug("%s: save    mask %#010x\n",
> +			 bank->name, save->eint_mask);
> +	} else if (bank->eint_type == EINT_TYPE_WKUP)
> +		exynos_set_wakeup(bank);
>  }
>  
> -void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata)
> +void exynosautov920_pinctrl_suspend(struct samsung_pin_bank *bank)
>  {
> -	struct samsung_pin_bank *bank = drvdata->pin_banks;
> -	struct exynos_irq_chip *irq_chip = NULL;
> -	int i;
> +	struct exynos_eint_gpio_save *save = bank->soc_priv;
> +	const void __iomem *regs = bank->eint_base;
>  
> -	for (i = 0; i < drvdata->nr_banks; ++i, ++bank) {
> -		if (bank->eint_type == EINT_TYPE_GPIO) {
> -			if (bank->eint_con_offset)
> -				exynosauto_pinctrl_suspend_bank(drvdata, bank);
> -			else
> -				exynos_pinctrl_suspend_bank(drvdata, bank);
> -		}
> -		else if (bank->eint_type == EINT_TYPE_WKUP) {
> -			if (!irq_chip) {
> -				irq_chip = bank->irq_chip;
> -				irq_chip->set_eint_wakeup_mask(drvdata,
> -							       irq_chip);
> -			}
> -		}
> -	}
> +	if (bank->eint_type == EINT_TYPE_GPIO) {
> +		save->eint_con = readl(regs + bank->pctl_offset +
> +				       bank->eint_con_offset);
> +		save->eint_mask = readl(regs + bank->pctl_offset +
> +					bank->eint_mask_offset);
> +		pr_debug("%s: save     con %#010x\n",
> +			 bank->name, save->eint_con);
> +		pr_debug("%s: save    mask %#010x\n",
> +			 bank->name, save->eint_mask);
> +	} else if (bank->eint_type == EINT_TYPE_WKUP)
> +		exynos_set_wakeup(bank);
>  }
>  
> -static void exynos_pinctrl_resume_bank(
> -				struct samsung_pinctrl_drv_data *drvdata,
> -				struct samsung_pin_bank *bank)
> +void exynos_pinctrl_resume(struct samsung_pin_bank *bank)
>  {
>  	struct exynos_eint_gpio_save *save = bank->soc_priv;
>  	void __iomem *regs = bank->eint_base;
>  
> -	if (clk_enable(bank->drvdata->pclk)) {
> -		dev_err(bank->gpio_chip.parent,
> -			"unable to enable clock for restoring state\n");
> -		return;
> +	if (bank->eint_type == EINT_TYPE_GPIO) {
> +		pr_debug("%s:     con %#010x => %#010x\n", bank->name,
> +			 readl(regs + EXYNOS_GPIO_ECON_OFFSET
> +			       + bank->eint_offset), save->eint_con);
> +		pr_debug("%s: fltcon0 %#010x => %#010x\n", bank->name,
> +			 readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> +			       + 2 * bank->eint_offset), save->eint_fltcon0);
> +		pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
> +			 readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> +			       + 2 * bank->eint_offset + 4),
> +			       save->eint_fltcon1);

here

> +		pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
> +			 readl(regs + bank->irq_chip->eint_mask
> +			       + bank->eint_offset), save->eint_mask);
> +
> +		writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
> +		       + bank->eint_offset);
> +		writel(save->eint_fltcon0, regs + EXYNOS_GPIO_EFLTCON_OFFSET
> +		       + 2 * bank->eint_offset);
> +		writel(save->eint_fltcon1, regs + EXYNOS_GPIO_EFLTCON_OFFSET
> +		       + 2 * bank->eint_offset + 4);
> +		writel(save->eint_mask, regs + bank->irq_chip->eint_mask
> +		       + bank->eint_offset);
>  	}
> -
> -	pr_debug("%s:     con %#010x => %#010x\n", bank->name,
> -			readl(regs + EXYNOS_GPIO_ECON_OFFSET
> -			+ bank->eint_offset), save->eint_con);
> -	pr_debug("%s: fltcon0 %#010x => %#010x\n", bank->name,
> -			readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> -			+ 2 * bank->eint_offset), save->eint_fltcon0);
> -	pr_debug("%s: fltcon1 %#010x => %#010x\n", bank->name,
> -			readl(regs + EXYNOS_GPIO_EFLTCON_OFFSET
> -			+ 2 * bank->eint_offset + 4), save->eint_fltcon1);
> -	pr_debug("%s:    mask %#010x => %#010x\n", bank->name,
> -			readl(regs + bank->irq_chip->eint_mask
> -			+ bank->eint_offset), save->eint_mask);
> -
> -	writel(save->eint_con, regs + EXYNOS_GPIO_ECON_OFFSET
> -						+ bank->eint_offset);
> -	writel(save->eint_fltcon0, regs + EXYNOS_GPIO_EFLTCON_OFFSET
> -						+ 2 * bank->eint_offset);
> -	writel(save->eint_fltcon1, regs + EXYNOS_GPIO_EFLTCON_OFFSET
> -						+ 2 * bank->eint_offset + 4);
> -	writel(save->eint_mask, regs + bank->irq_chip->eint_mask
> -						+ bank->eint_offset);
> -
> -	clk_disable(bank->drvdata->pclk);
>  }
>  
> -static void exynosauto_pinctrl_resume_bank(struct samsung_pinctrl_drv_data *drvdata,
> -					   struct samsung_pin_bank *bank)
> +void exynosautov920_pinctrl_resume(struct samsung_pin_bank *bank)
>  {
>  	struct exynos_eint_gpio_save *save = bank->soc_priv;
>  	void __iomem *regs = bank->eint_base;
>  
> -	if (clk_enable(bank->drvdata->pclk)) {
> -		dev_err(bank->gpio_chip.parent,
> -			"unable to enable clock for restoring state\n");
> -		return;
> +	if (bank->eint_type == EINT_TYPE_GPIO) {
> +		/* exynosautov920 has eint_con_offset for all but one bank */
> +		if (!bank->eint_con_offset)
> +			exynos_pinctrl_resume(bank);
> +
> +		pr_debug("%s:     con %#010x => %#010x\n", bank->name,
> +			 readl(regs + bank->pctl_offset + bank->eint_con_offset),
> +			       save->eint_con);

and here.

Cheers,
A.