[PATCH v5 08/11] gpio: max7360: Add MAX7360 gpio support

[Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>]

Add driver for Maxim Integrated MAX7360 GPIO/GPO controller.

Two sets of GPIOs are provided by the device:
- Up to 8 GPIOs, shared with the PWM and rotary encoder functionalities.
  These GPIOs also provide interrupts on input changes.
- Up to 6 GPOs, on unused keypad columns pins.

Co-developed-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
---
 drivers/gpio/Kconfig        |  12 +++
 drivers/gpio/Makefile       |   1 +
 drivers/gpio/gpio-max7360.c | 246 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 259 insertions(+)

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 98b4d1633b25..4ff68ec6a990 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1445,6 +1445,18 @@ config GPIO_MADERA
 	help
 	  Support for GPIOs on Cirrus Logic Madera class codecs.
 
+config GPIO_MAX7360
+	tristate "MAX7360 GPIO support"
+	depends on MFD_MAX7360
+	select GPIO_REGMAP
+	select PINCTRL_MAX7360
+	help
+	  Allows to use MAX7360 I/O Expander PWM lines as GPIO and keypad COL
+	  lines as GPO.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called gpio-max7360.
+
 config GPIO_MAX77620
 	tristate "GPIO support for PMIC MAX77620 and MAX20024"
 	depends on MFD_MAX77620
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index af3ba4d81b58..581341b3e3e4 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -100,6 +100,7 @@ obj-$(CONFIG_GPIO_MAX7300)		+= gpio-max7300.o
 obj-$(CONFIG_GPIO_MAX7301)		+= gpio-max7301.o
 obj-$(CONFIG_GPIO_MAX730X)		+= gpio-max730x.o
 obj-$(CONFIG_GPIO_MAX732X)		+= gpio-max732x.o
+obj-$(CONFIG_GPIO_MAX7360)		+= gpio-max7360.o
 obj-$(CONFIG_GPIO_MAX77620)		+= gpio-max77620.o
 obj-$(CONFIG_GPIO_MAX77650)		+= gpio-max77650.o
 obj-$(CONFIG_GPIO_MB86S7X)		+= gpio-mb86s7x.o
diff --git a/drivers/gpio/gpio-max7360.c b/drivers/gpio/gpio-max7360.c
new file mode 100644
index 000000000000..4acf0a9dbaba
--- /dev/null
+++ b/drivers/gpio/gpio-max7360.c
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2025 Bootlin
+ *
+ * Author: Kamel BOUHARA <kamel.bouhara@bootlin.com>
+ * Author: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
+ */
+
+#include <linux/bitmap.h>
+#include <linux/gpio/driver.h>
+#include <linux/gpio/regmap.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/max7360.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define MAX7360_GPIO_PORT	1
+#define MAX7360_GPIO_COL	2
+
+static int max7360_get_available_gpos(struct device *dev, unsigned int *available_gpios)
+{
+	u32 columns;
+	int ret;
+
+	ret = device_property_read_u32(dev->parent, "keypad,num-columns", &columns);
+	if (ret < 0) {
+		dev_err(dev, "Failed to read columns count\n");
+		return ret;
+	}
+
+	*available_gpios = min(MAX7360_MAX_GPO, MAX7360_MAX_KEY_COLS - columns);
+
+	return 0;
+}
+
+static int max7360_gpo_init_valid_mask(struct gpio_chip *gc,
+				       unsigned long *valid_mask,
+				       unsigned int ngpios)
+{
+	unsigned int available_gpios;
+	int ret;
+
+	ret = max7360_get_available_gpos(gc->parent, &available_gpios);
+	if (ret)
+		return ret;
+
+	bitmap_clear(valid_mask, 0, MAX7360_MAX_KEY_COLS - ngpios);
+
+	return 0;
+}
+
+static int max7360_set_gpos_count(struct device *dev, struct regmap *regmap)
+{
+	/*
+	 * MAX7360 COL0 to COL7 pins can be used either as keypad columns,
+	 * general purpose output or a mix of both.
+	 * By default, all pins are used as keypad, here we update this
+	 * configuration to allow to use some of them as GPIOs.
+	 */
+	unsigned int available_gpios;
+	unsigned int val;
+	int ret;
+
+	ret = max7360_get_available_gpos(dev, &available_gpios);
+	if (ret)
+		return ret;
+
+	/*
+	 * Configure which GPIOs will be used for keypad.
+	 * MAX7360_REG_DEBOUNCE contains configuration both for keypad debounce
+	 * timings and gpos/keypad columns repartition. Only the later is
+	 * modified here.
+	 */
+	val = FIELD_PREP(MAX7360_PORTS, available_gpios);
+	ret = regmap_write_bits(regmap, MAX7360_REG_DEBOUNCE, MAX7360_PORTS, val);
+	if (ret) {
+		dev_err(dev, "Failed to write max7360 columns/gpos configuration");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int max7360_gpio_reg_mask_xlate(struct gpio_regmap *gpio,
+				       unsigned int base, unsigned int offset,
+				       unsigned int *reg, unsigned int *mask)
+{
+	if (base == MAX7360_REG_PWMBASE) {
+		/*
+		 * GPIO output is using PWM duty cycle registers: one register
+		 * per line, with value being either 0 or 255.
+		 */
+		*reg = base + offset;
+		*mask = 0xFF;
+	} else {
+		*reg = base;
+		*mask = BIT(offset);
+	}
+
+	return 0;
+}
+
+static const struct regmap_irq max7360_regmap_irqs[MAX7360_MAX_GPIO] = {
+	REGMAP_IRQ_REG(0, 0, BIT(0)),
+	REGMAP_IRQ_REG(1, 0, BIT(1)),
+	REGMAP_IRQ_REG(2, 0, BIT(2)),
+	REGMAP_IRQ_REG(3, 0, BIT(3)),
+	REGMAP_IRQ_REG(4, 0, BIT(4)),
+	REGMAP_IRQ_REG(5, 0, BIT(5)),
+	REGMAP_IRQ_REG(6, 0, BIT(6)),
+	REGMAP_IRQ_REG(7, 0, BIT(7)),
+};
+
+static int max7360_handle_mask_sync(const int index,
+				    const unsigned int mask_buf_def,
+				    const unsigned int mask_buf,
+				    void *const irq_drv_data)
+{
+	struct regmap *regmap = irq_drv_data;
+	unsigned int val;
+
+	for (unsigned int i = 0; i < MAX7360_MAX_GPIO; ++i) {
+		val = (mask_buf & BIT(i)) ? MAX7360_PORT_CFG_INTERRUPT_MASK : 0;
+		regmap_write_bits(regmap, MAX7360_REG_PWMCFG(i),
+				  MAX7360_PORT_CFG_INTERRUPT_MASK, val);
+	}
+
+	return 0;
+}
+
+static int max7360_gpio_probe(struct platform_device *pdev)
+{
+	struct regmap_irq_chip *irq_chip;
+	struct gpio_regmap_config gpio_config = { };
+	struct device *dev = &pdev->dev;
+	unsigned long gpio_function;
+	struct regmap *regmap;
+	unsigned int outconf;
+	int ret;
+
+	regmap = dev_get_regmap(dev->parent, NULL);
+	if (!regmap)
+		return dev_err_probe(dev, -ENODEV, "could not get parent regmap\n");
+
+	gpio_function = (uintptr_t)device_get_match_data(dev);
+
+	if (gpio_function == MAX7360_GPIO_PORT &&
+	    (device_property_read_bool(dev, "interrupt-controller"))) {
+		/*
+		 * Port GPIOs with interrupt-controller property: add IRQ
+		 * controller.
+		 */
+		gpio_config.regmap_irq_flags = IRQF_TRIGGER_LOW | IRQF_ONESHOT | IRQF_SHARED;
+		gpio_config.regmap_irq_irqno = fwnode_irq_get_byname(dev_fwnode(dev->parent),
+								     "inti");
+		if (gpio_config.regmap_irq_irqno < 0)
+			return dev_err_probe(dev, gpio_config.regmap_irq_irqno,
+					     "Failed to get IRQ\n");
+
+		irq_chip = devm_kzalloc(dev, sizeof(*irq_chip), GFP_KERNEL);
+		gpio_config.regmap_irq_chip = irq_chip;
+		if (!irq_chip)
+			return -ENOMEM;
+
+		irq_chip->name = dev_name(dev);
+		irq_chip->status_base = MAX7360_REG_GPIOIN;
+		irq_chip->num_regs = 1;
+		irq_chip->num_irqs = MAX7360_MAX_GPIO;
+		irq_chip->irqs = max7360_regmap_irqs;
+		irq_chip->handle_mask_sync = max7360_handle_mask_sync;
+		irq_chip->status_is_level = true;
+		irq_chip->irq_drv_data = regmap;
+
+		for (unsigned int i = 0; i < MAX7360_MAX_GPIO; i++) {
+			regmap_write_bits(regmap, MAX7360_REG_PWMCFG(i),
+					  MAX7360_PORT_CFG_INTERRUPT_EDGES,
+					  MAX7360_PORT_CFG_INTERRUPT_EDGES);
+		}
+	}
+
+	if (gpio_function == MAX7360_GPIO_PORT) {
+		/*
+		 * Port GPIOs: set output mode configuration (constant-current or not).
+		 * This property is optional.
+		 */
+		outconf = 0;
+		ret = device_property_read_u32(dev, "maxim,constant-current-disable", &outconf);
+		if (ret && (ret != -EINVAL))
+			return dev_err_probe(dev, ret, "Failed to read %s device property\n",
+					     "maxim,constant-current-disable");
+
+		regmap_write(regmap, MAX7360_REG_GPIOOUTM, outconf);
+	}
+
+	/* Add gpio device. */
+	gpio_config.parent = dev;
+	gpio_config.regmap = regmap;
+	if (gpio_function == MAX7360_GPIO_PORT) {
+		gpio_config.ngpio = MAX7360_MAX_GPIO;
+		gpio_config.reg_dat_base = GPIO_REGMAP_ADDR(MAX7360_REG_GPIOIN);
+		gpio_config.reg_set_base = GPIO_REGMAP_ADDR(MAX7360_REG_PWMBASE);
+		gpio_config.reg_dir_out_base = GPIO_REGMAP_ADDR(MAX7360_REG_GPIOCTRL);
+		gpio_config.ngpio_per_reg = MAX7360_MAX_GPIO;
+		gpio_config.reg_mask_xlate = max7360_gpio_reg_mask_xlate;
+	} else {
+		ret = max7360_set_gpos_count(dev, regmap);
+		if (ret)
+			return dev_err_probe(dev, ret, "Failed to set GPOS pin count\n");
+
+		gpio_config.reg_set_base = GPIO_REGMAP_ADDR(MAX7360_REG_PORTS);
+		gpio_config.ngpio = MAX7360_MAX_KEY_COLS;
+		gpio_config.init_valid_mask = max7360_gpo_init_valid_mask;
+	}
+
+	return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(dev, &gpio_config));
+}
+
+static const struct of_device_id max7360_gpio_of_match[] = {
+	{
+		.compatible = "maxim,max7360-gpo",
+		.data = (void *)MAX7360_GPIO_COL
+	}, {
+		.compatible = "maxim,max7360-gpio",
+		.data = (void *)MAX7360_GPIO_PORT
+	}, {
+	}
+};
+MODULE_DEVICE_TABLE(of, max7360_gpio_of_match);
+
+static struct platform_driver max7360_gpio_driver = {
+	.driver = {
+		.name	= "max7360-gpio",
+		.of_match_table = max7360_gpio_of_match,
+	},
+	.probe		= max7360_gpio_probe,
+};
+module_platform_driver(max7360_gpio_driver);
+
+MODULE_DESCRIPTION("MAX7360 GPIO driver");
+MODULE_AUTHOR("Kamel BOUHARA <kamel.bouhara@bootlin.com>");
+MODULE_AUTHOR("Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>");
+MODULE_LICENSE("GPL");

-- 
2.39.5