[PATCH v5 0/2] ESWIN EIC7700 pinctrl driver

[PATCH v5 0/2] ESWIN EIC7700 pinctrl driver

[Yulin Lu]

  Implements support for the Eswin eic7700 SoC pinctrl controller.
  Provides API to manage pinctrl for the eic7700 SoC.
  Integration with the Linux pinctrl subsystem for consistency and
  scalability.

  Supported chips:
    Eswin eic7700 SoC.

  Test:
    Tested this patch on the Sifive HiFive Premier P550 (which uses
    the EIC7700 SoC), including system boot, networking, EMMC, display,
    and other peripherals. The drivers for these modules all use the
    pinctrl module, so this verifies that this pinctrl driver
    patch is working properly.

---
Changes since V4:
  pinctrl: eswin: Add EIC7700 pinctrl driver
  - Added #ifdef CONFIG_OF to fix the kernel robot test compilation error.
  - Removed "Reviewed-by" tag of "Krzysztof Kozlowski"
  - Link: https://lore.kernel.org/all/20250515054524.390-1-luyulin@eswincomputing.com/

Yulin Lu (2):
  dt-bindings: pinctrl: eswin: Document for EIC7700 SoC
  pinctrl: eswin: Add EIC7700 pinctrl driver

 .../pinctrl/eswin,eic7700-pinctrl.yaml        | 156 ++++
 drivers/pinctrl/Kconfig                       |  11 +
 drivers/pinctrl/Makefile                      |   1 +
 drivers/pinctrl/pinctrl-eic7700.c             | 704 ++++++++++++++++++
 4 files changed, 872 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml
 create mode 100644 drivers/pinctrl/pinctrl-eic7700.c

-- 
2.25.1

[PATCH v5 1/2] dt-bindings: pinctrl: eswin: Document for EIC7700 SoC

[Yulin Lu]

Add EIC7700 pinctrl device for all configurable pins.
For the EIC7700 pinctrl registers, each register (32 bits)
controls the characteristics of a single pin.
It supports setting function multiplexing, Schmitt trigger,
drive strength, pull-up/pull-down, and input enable.

Co-developed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Yulin Lu <luyulin@eswincomputing.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../pinctrl/eswin,eic7700-pinctrl.yaml        | 156 ++++++++++++++++++
 1 file changed, 156 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml
new file mode 100644
index 000000000000..d46e7ee6372d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/eswin,eic7700-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Eswin Eic7700 Pinctrl
+
+maintainers:
+  - Yulin Lu <luyulin@eswincomputing.com>
+
+allOf:
+  - $ref: pinctrl.yaml#
+
+description: |
+  eic7700 pin configuration nodes act as a container for an arbitrary number of
+  subnodes. Each of these subnodes represents some desired configuration for one or
+  more pins. This configuration can include the mux function to select on those pin(s),
+  and various pin configuration parameters, such as input-enable, pull-up, etc.
+
+properties:
+  compatible:
+    const: eswin,eic7700-pinctrl
+
+  reg:
+    maxItems: 1
+
+  vrgmii-supply:
+    description:
+      Regulator supply for the RGMII interface IO power domain.
+      This property should reference a regulator that provides either 1.8V or 3.3V,
+      depending on the board-level voltage configuration required by the RGMII interface.
+
+patternProperties:
+  '-grp$':
+    type: object
+    additionalProperties: false
+
+    patternProperties:
+      '-pins$':
+        type: object
+
+        properties:
+          pins:
+            description:
+              For eic7700, specifies the name(s) of one or more pins to be configured by
+              this node.
+            items:
+              enum: [ chip_mode, mode_set0, mode_set1, mode_set2, mode_set3, xin,
+                      rst_out_n, key_reset_n, gpio0, por_sel, jtag0_tck, jtag0_tms,
+                      jtag0_tdi, jtag0_tdo, gpio5, spi2_cs0_n, jtag1_tck, jtag1_tms,
+                      jtag1_tdi, jtag1_tdo, gpio11, spi2_cs1_n, pcie_clkreq_n,
+                      pcie_wake_n, pcie_perst_n, hdmi_scl, hdmi_sda, hdmi_cec,
+                      jtag2_trst, rgmii0_clk_125, rgmii0_txen, rgmii0_txclk,
+                      rgmii0_txd0, rgmii0_txd1, rgmii0_txd2, rgmii0_txd3, i2s0_bclk,
+                      i2s0_wclk, i2s0_sdi, i2s0_sdo, i2s_mclk, rgmii0_rxclk,
+                      rgmii0_rxdv, rgmii0_rxd0, rgmii0_rxd1, rgmii0_rxd2, rgmii0_rxd3,
+                      i2s2_bclk, i2s2_wclk, i2s2_sdi, i2s2_sdo, gpio27, gpio28, gpio29,
+                      rgmii0_mdc, rgmii0_mdio, rgmii0_intb, rgmii1_clk_125, rgmii1_txen,
+                      rgmii1_txclk, rgmii1_txd0, rgmii1_txd1, rgmii1_txd2, rgmii1_txd3,
+                      i2s1_bclk, i2s1_wclk, i2s1_sdi, i2s1_sdo, gpio34, rgmii1_rxclk,
+                      rgmii1_rxdv, rgmii1_rxd0, rgmii1_rxd1, rgmii1_rxd2, rgmii1_rxd3,
+                      spi1_cs0_n, spi1_clk, spi1_d0, spi1_d1, spi1_d2, spi1_d3, spi1_cs1_n,
+                      rgmii1_mdc, rgmii1_mdio, rgmii1_intb, usb0_pwren, usb1_pwren,
+                      i2c0_scl, i2c0_sda, i2c1_scl, i2c1_sda, i2c2_scl, i2c2_sda,
+                      i2c3_scl, i2c3_sda, i2c4_scl, i2c4_sda, i2c5_scl, i2c5_sda,
+                      uart0_tx, uart0_rx, uart1_tx, uart1_rx, uart1_cts, uart1_rts,
+                      uart2_tx, uart2_rx, jtag2_tck, jtag2_tms, jtag2_tdi, jtag2_tdo,
+                      fan_pwm, fan_tach, mipi_csi0_xvs, mipi_csi0_xhs, mipi_csi0_mclk,
+                      mipi_csi1_xvs, mipi_csi1_xhs, mipi_csi1_mclk, mipi_csi2_xvs,
+                      mipi_csi2_xhs, mipi_csi2_mclk, mipi_csi3_xvs, mipi_csi3_xhs,
+                      mipi_csi3_mclk, mipi_csi4_xvs, mipi_csi4_xhs, mipi_csi4_mclk,
+                      mipi_csi5_xvs, mipi_csi5_xhs, mipi_csi5_mclk, spi3_cs_n, spi3_clk,
+                      spi3_di, spi3_do, gpio92, gpio93, s_mode, gpio95, spi0_cs_n,
+                      spi0_clk, spi0_d0, spi0_d1, spi0_d2, spi0_d3, i2c10_scl,
+                      i2c10_sda, i2c11_scl, i2c11_sda, gpio106, boot_sel0, boot_sel1,
+                      boot_sel2, boot_sel3, gpio111, lpddr_ref_clk ]
+
+          function:
+            description:
+              Specify the alternative function to be configured for the
+              given pins.
+            enum: [ disabled, boot_sel, chip_mode, emmc, fan_tach,
+                    gpio, hdmi, i2c, i2s, jtag, ddr_ref_clk_sel,
+                    lpddr_ref_clk, mipi_csi, osc, pcie, pwm,
+                    rgmii, reset, sata, sdio, spi, s_mode, uart, usb ]
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+          bias-disable: true
+
+          bias-pull-down: true
+
+          bias-pull-up: true
+
+          input-enable: true
+
+          input-disable: true
+
+          drive-strength-microamp: true
+
+        required:
+          - pins
+
+        additionalProperties: false
+
+        allOf:
+          - $ref: pincfg-node.yaml#
+          - $ref: pinmux-node.yaml#
+
+          - if:
+              properties:
+                pins:
+                  anyOf:
+                    - pattern: '^rgmii'
+                    - const: lpddr_ref_clk
+            then:
+              properties:
+                drive-strength-microamp:
+                  enum: [3000, 6000, 9000, 12000, 15000, 18000, 21000, 24000]
+            else:
+              properties:
+                drive-strength-microamp:
+                  enum: [6000, 9000, 12000, 15000, 18000, 21000, 24000, 27000]
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    pinctrl@51600080 {
+      compatible = "eswin,eic7700-pinctrl";
+      reg = <0x51600080 0x1fff80>;
+      vrgmii-supply = <&vcc_1v8>;
+
+      dev-active-grp {
+        /* group node defining 1 standard pin */
+        gpio10-pins {
+          pins = "jtag1_tdo";
+          function = "gpio";
+          input-enable;
+          bias-pull-up;
+        };
+
+        /* group node defining 2 I2C pins */
+        i2c6-pins {
+          pins = "uart1_cts", "uart1_rts";
+          function = "i2c";
+        };
+      };
+    };
-- 
2.25.1

[PATCH v5 1/2] dt-bindings: pinctrl: eswin: Document for EIC7700 SoC

[Yulin Lu]

Add EIC7700 pinctrl device for all configurable pins.
For the EIC7700 pinctrl registers, each register (32 bits)
controls the characteristics of a single pin.
It supports setting function multiplexing, Schmitt trigger,
drive strength, pull-up/pull-down, and input enable.

Co-developed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Yulin Lu <luyulin@eswincomputing.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../pinctrl/eswin,eic7700-pinctrl.yaml        | 156 ++++++++++++++++++
 1 file changed, 156 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml
new file mode 100644
index 000000000000..d46e7ee6372d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/eswin,eic7700-pinctrl.yaml
@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/eswin,eic7700-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Eswin Eic7700 Pinctrl
+
+maintainers:
+  - Yulin Lu <luyulin@eswincomputing.com>
+
+allOf:
+  - $ref: pinctrl.yaml#
+
+description: |
+  eic7700 pin configuration nodes act as a container for an arbitrary number of
+  subnodes. Each of these subnodes represents some desired configuration for one or
+  more pins. This configuration can include the mux function to select on those pin(s),
+  and various pin configuration parameters, such as input-enable, pull-up, etc.
+
+properties:
+  compatible:
+    const: eswin,eic7700-pinctrl
+
+  reg:
+    maxItems: 1
+
+  vrgmii-supply:
+    description:
+      Regulator supply for the RGMII interface IO power domain.
+      This property should reference a regulator that provides either 1.8V or 3.3V,
+      depending on the board-level voltage configuration required by the RGMII interface.
+
+patternProperties:
+  '-grp$':
+    type: object
+    additionalProperties: false
+
+    patternProperties:
+      '-pins$':
+        type: object
+
+        properties:
+          pins:
+            description:
+              For eic7700, specifies the name(s) of one or more pins to be configured by
+              this node.
+            items:
+              enum: [ chip_mode, mode_set0, mode_set1, mode_set2, mode_set3, xin,
+                      rst_out_n, key_reset_n, gpio0, por_sel, jtag0_tck, jtag0_tms,
+                      jtag0_tdi, jtag0_tdo, gpio5, spi2_cs0_n, jtag1_tck, jtag1_tms,
+                      jtag1_tdi, jtag1_tdo, gpio11, spi2_cs1_n, pcie_clkreq_n,
+                      pcie_wake_n, pcie_perst_n, hdmi_scl, hdmi_sda, hdmi_cec,
+                      jtag2_trst, rgmii0_clk_125, rgmii0_txen, rgmii0_txclk,
+                      rgmii0_txd0, rgmii0_txd1, rgmii0_txd2, rgmii0_txd3, i2s0_bclk,
+                      i2s0_wclk, i2s0_sdi, i2s0_sdo, i2s_mclk, rgmii0_rxclk,
+                      rgmii0_rxdv, rgmii0_rxd0, rgmii0_rxd1, rgmii0_rxd2, rgmii0_rxd3,
+                      i2s2_bclk, i2s2_wclk, i2s2_sdi, i2s2_sdo, gpio27, gpio28, gpio29,
+                      rgmii0_mdc, rgmii0_mdio, rgmii0_intb, rgmii1_clk_125, rgmii1_txen,
+                      rgmii1_txclk, rgmii1_txd0, rgmii1_txd1, rgmii1_txd2, rgmii1_txd3,
+                      i2s1_bclk, i2s1_wclk, i2s1_sdi, i2s1_sdo, gpio34, rgmii1_rxclk,
+                      rgmii1_rxdv, rgmii1_rxd0, rgmii1_rxd1, rgmii1_rxd2, rgmii1_rxd3,
+                      spi1_cs0_n, spi1_clk, spi1_d0, spi1_d1, spi1_d2, spi1_d3, spi1_cs1_n,
+                      rgmii1_mdc, rgmii1_mdio, rgmii1_intb, usb0_pwren, usb1_pwren,
+                      i2c0_scl, i2c0_sda, i2c1_scl, i2c1_sda, i2c2_scl, i2c2_sda,
+                      i2c3_scl, i2c3_sda, i2c4_scl, i2c4_sda, i2c5_scl, i2c5_sda,
+                      uart0_tx, uart0_rx, uart1_tx, uart1_rx, uart1_cts, uart1_rts,
+                      uart2_tx, uart2_rx, jtag2_tck, jtag2_tms, jtag2_tdi, jtag2_tdo,
+                      fan_pwm, fan_tach, mipi_csi0_xvs, mipi_csi0_xhs, mipi_csi0_mclk,
+                      mipi_csi1_xvs, mipi_csi1_xhs, mipi_csi1_mclk, mipi_csi2_xvs,
+                      mipi_csi2_xhs, mipi_csi2_mclk, mipi_csi3_xvs, mipi_csi3_xhs,
+                      mipi_csi3_mclk, mipi_csi4_xvs, mipi_csi4_xhs, mipi_csi4_mclk,
+                      mipi_csi5_xvs, mipi_csi5_xhs, mipi_csi5_mclk, spi3_cs_n, spi3_clk,
+                      spi3_di, spi3_do, gpio92, gpio93, s_mode, gpio95, spi0_cs_n,
+                      spi0_clk, spi0_d0, spi0_d1, spi0_d2, spi0_d3, i2c10_scl,
+                      i2c10_sda, i2c11_scl, i2c11_sda, gpio106, boot_sel0, boot_sel1,
+                      boot_sel2, boot_sel3, gpio111, lpddr_ref_clk ]
+
+          function:
+            description:
+              Specify the alternative function to be configured for the
+              given pins.
+            enum: [ disabled, boot_sel, chip_mode, emmc, fan_tach,
+                    gpio, hdmi, i2c, i2s, jtag, ddr_ref_clk_sel,
+                    lpddr_ref_clk, mipi_csi, osc, pcie, pwm,
+                    rgmii, reset, sata, sdio, spi, s_mode, uart, usb ]
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+          bias-disable: true
+
+          bias-pull-down: true
+
+          bias-pull-up: true
+
+          input-enable: true
+
+          input-disable: true
+
+          drive-strength-microamp: true
+
+        required:
+          - pins
+
+        additionalProperties: false
+
+        allOf:
+          - $ref: pincfg-node.yaml#
+          - $ref: pinmux-node.yaml#
+
+          - if:
+              properties:
+                pins:
+                  anyOf:
+                    - pattern: '^rgmii'
+                    - const: lpddr_ref_clk
+            then:
+              properties:
+                drive-strength-microamp:
+                  enum: [3000, 6000, 9000, 12000, 15000, 18000, 21000, 24000]
+            else:
+              properties:
+                drive-strength-microamp:
+                  enum: [6000, 9000, 12000, 15000, 18000, 21000, 24000, 27000]
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    pinctrl@51600080 {
+      compatible = "eswin,eic7700-pinctrl";
+      reg = <0x51600080 0x1fff80>;
+      vrgmii-supply = <&vcc_1v8>;
+
+      dev-active-grp {
+        /* group node defining 1 standard pin */
+        gpio10-pins {
+          pins = "jtag1_tdo";
+          function = "gpio";
+          input-enable;
+          bias-pull-up;
+        };
+
+        /* group node defining 2 I2C pins */
+        i2c6-pins {
+          pins = "uart1_cts", "uart1_rts";
+          function = "i2c";
+        };
+      };
+    };
-- 
2.25.1

[PATCH v5 2/2] pinctrl: eswin: Add EIC7700 pinctrl driver

[Yulin Lu]

Add support for the pin controller in ESWIN's EIC7700 SoC,
which supports pin multiplexing, pin configuration,
and rgmii voltage control.

Co-developed-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Yulin Lu <luyulin@eswincomputing.com>
---
 drivers/pinctrl/Kconfig           |  11 +
 drivers/pinctrl/Makefile          |   1 +
 drivers/pinctrl/pinctrl-eic7700.c | 704 ++++++++++++++++++++++++++++++
 3 files changed, 716 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-eic7700.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 33db9104df17..e3e0cac002d2 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -206,6 +206,17 @@ config PINCTRL_DIGICOLOR
 	select PINMUX
 	select GENERIC_PINCONF
 
+config PINCTRL_EIC7700
+	tristate "EIC7700 PINCTRL driver"
+	depends on ARCH_ESWIN || COMPILE_TEST
+	select PINMUX
+	select GENERIC_PINCONF
+	help
+	  This driver support for the pin controller in ESWIN's EIC7700 SoC,
+	  which supports pin multiplexing, pin configuration,and rgmii voltage
+	  control.
+	  Say Y here to enable the eic7700 pinctrl driver
+
 config PINCTRL_EP93XX
 	bool
 	depends on ARCH_EP93XX || COMPILE_TEST
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index ac27e88677d1..82e0d4cf5045 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_PINCTRL_CY8C95X0)	+= pinctrl-cy8c95x0.o
 obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o
 obj-$(CONFIG_PINCTRL_DA9062)	+= pinctrl-da9062.o
 obj-$(CONFIG_PINCTRL_DIGICOLOR)	+= pinctrl-digicolor.o
+obj-$(CONFIG_PINCTRL_EIC7700)	+= pinctrl-eic7700.o
 obj-$(CONFIG_PINCTRL_EQUILIBRIUM)   += pinctrl-equilibrium.o
 obj-$(CONFIG_PINCTRL_EP93XX)	+= pinctrl-ep93xx.o
 obj-$(CONFIG_PINCTRL_EYEQ5)	+= pinctrl-eyeq5.o
diff --git a/drivers/pinctrl/pinctrl-eic7700.c b/drivers/pinctrl/pinctrl-eic7700.c
new file mode 100644
index 000000000000..719cd11e276a
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-eic7700.c
@@ -0,0 +1,704 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ESWIN Pinctrl Controller Platform Device Driver
+ *
+ * Copyright 2024, Beijing ESWIN Computing Technology Co., Ltd.. All rights reserved.
+ *
+ * Authors: Samuel Holland <samuel.holland@sifive.com>
+ *          Yulin Lu <luyulin@eswincomputing.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/seq_file.h>
+#include <linux/regulator/consumer.h>
+
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include "core.h"
+#include "pinmux.h"
+#include "pinconf.h"
+
+#define EIC7700_PIN_REG(i)		(4 * (i))
+#define EIC7700_IE			BIT(0)
+#define EIC7700_PU			BIT(1)
+#define EIC7700_PD			BIT(2)
+#define EIC7700_DS			GENMASK(6, 3)
+#define EIC7700_ST			BIT(7)
+#define EIC7700_FUNC_SEL		GENMASK(18, 16)
+
+#define EIC7700_BIAS			(EIC7700_PD | EIC7700_PU)
+#define EIC7700_PINCONF			GENMASK(7, 0)
+
+#define EIC7700_RGMII0_SEL_MODE		(0x310 - 0x80)
+#define EIC7700_RGMII1_SEL_MODE		(0x314 - 0x80)
+#define EIC7700_MS			GENMASK(1, 0)
+#define EIC7700_MS_3V3			0x0
+#define EIC7700_MS_1V8			0x3
+
+#define EIC7700_FUNCTIONS_PER_PIN	8
+
+struct eic7700_pin {
+	u8 functions[EIC7700_FUNCTIONS_PER_PIN];
+};
+
+struct eic7700_pinctrl {
+	void __iomem *base;
+	struct pinctrl_desc desc;
+	unsigned int functions_count;
+	struct pinfunction functions[] __counted_by(functions_count);
+};
+
+enum {
+	F_DISABLED,
+	F_BOOT_SEL,
+	F_CHIP_MODE,
+	F_EMMC,
+	F_FAN_TACH,
+	F_GPIO,
+	F_HDMI,
+	F_I2C,
+	F_I2S,
+	F_JTAG,
+	F_DDR_REF_CLK_SEL,
+	F_LPDDR_REF_CLK,
+	F_MIPI_CSI,
+	F_OSC,
+	F_PCIE,
+	F_PWM,
+	F_RGMII,
+	F_RESET,
+	F_SATA,
+	F_SDIO,
+	F_SPI,
+	F_S_MODE,
+	F_UART,
+	F_USB,
+	EIC7700_FUNCTIONS_COUNT
+};
+
+static const char *const eic7700_functions[EIC7700_FUNCTIONS_COUNT] = {
+	[F_DISABLED]		= "disabled",
+	[F_BOOT_SEL]		= "boot_sel",
+	[F_CHIP_MODE]		= "chip_mode",
+	[F_EMMC]		= "emmc",
+	[F_FAN_TACH]		= "fan_tach",
+	[F_GPIO]		= "gpio",
+	[F_HDMI]		= "hdmi",
+	[F_I2C]			= "i2c",
+	[F_I2S]			= "i2s",
+	[F_JTAG]		= "jtag",
+	[F_DDR_REF_CLK_SEL]	= "ddr_ref_clk_sel",
+	[F_LPDDR_REF_CLK]	= "lpddr_ref_clk",
+	[F_MIPI_CSI]		= "mipi_csi",
+	[F_OSC]			= "osc",
+	[F_PCIE]		= "pcie",
+	[F_PWM]			= "pwm",
+	[F_RGMII]		= "rgmii",
+	[F_RESET]		= "reset",
+	[F_SATA]		= "sata",
+	[F_SDIO]		= "sdio",
+	[F_SPI]			= "spi",
+	[F_S_MODE]		= "s_mode",
+	[F_UART]		= "uart",
+	[F_USB]			= "usb",
+};
+
+#define EIC7700_PIN(_number, _name, ...) \
+	{ \
+		.number	= _number, \
+		.name = _name, \
+		.drv_data = (void *)&(struct eic7700_pin) { { __VA_ARGS__ } } \
+	}
+
+static const struct pinctrl_pin_desc eic7700_pins[] = {
+	EIC7700_PIN(0,   "chip_mode",		[0] = F_CHIP_MODE),
+	EIC7700_PIN(1,   "mode_set0",		[0] = F_SDIO, [2] = F_GPIO),
+	EIC7700_PIN(2,   "mode_set1",		[0] = F_SDIO, [2] = F_GPIO),
+	EIC7700_PIN(3,   "mode_set2",		[0] = F_SDIO, [2] = F_GPIO),
+	EIC7700_PIN(4,   "mode_set3",		[0] = F_SDIO, [2] = F_GPIO),
+	EIC7700_PIN(5,   "xin",			[0] = F_OSC),
+	EIC7700_PIN(6,   "rtc_xin",		[0] = F_DISABLED),
+	EIC7700_PIN(7,   "rst_out_n",		[0] = F_RESET),
+	EIC7700_PIN(8,   "key_reset_n",		[0] = F_RESET),
+	EIC7700_PIN(9,   "rst_in_n",		[0] = F_DISABLED),
+	EIC7700_PIN(10,  "por_in_n",		[0] = F_DISABLED),
+	EIC7700_PIN(11,  "por_out_n",		[0] = F_DISABLED),
+	EIC7700_PIN(12,  "gpio0",		[0] = F_GPIO),
+	EIC7700_PIN(13,  "por_sel",		[0] = F_RESET),
+	EIC7700_PIN(14,  "jtag0_tck",		[0] = F_JTAG, [1] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(15,  "jtag0_tms",		[0] = F_JTAG, [1] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(16,  "jtag0_tdi",		[0] = F_JTAG, [1] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(17,  "jtag0_tdo",		[0] = F_JTAG, [1] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(18,  "gpio5",		[0] = F_GPIO, [1] = F_SPI),
+	EIC7700_PIN(19,  "spi2_cs0_n",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(20,  "jtag1_tck",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(21,  "jtag1_tms",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(22,  "jtag1_tdi",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(23,  "jtag1_tdo",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(24,  "gpio11",		[0] = F_GPIO),
+	EIC7700_PIN(25,  "spi2_cs1_n",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(26,  "pcie_clkreq_n",	[0] = F_PCIE),
+	EIC7700_PIN(27,  "pcie_wake_n",		[0] = F_PCIE),
+	EIC7700_PIN(28,  "pcie_perst_n",	[0] = F_PCIE),
+	EIC7700_PIN(29,  "hdmi_scl",		[0] = F_HDMI),
+	EIC7700_PIN(30,  "hdmi_sda",		[0] = F_HDMI),
+	EIC7700_PIN(31,  "hdmi_cec",		[0] = F_HDMI),
+	EIC7700_PIN(32,  "jtag2_trst",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(33,  "rgmii0_clk_125",	[0] = F_RGMII),
+	EIC7700_PIN(34,  "rgmii0_txen",		[0] = F_RGMII),
+	EIC7700_PIN(35,  "rgmii0_txclk",	[0] = F_RGMII),
+	EIC7700_PIN(36,  "rgmii0_txd0",		[0] = F_RGMII),
+	EIC7700_PIN(37,  "rgmii0_txd1",		[0] = F_RGMII),
+	EIC7700_PIN(38,  "rgmii0_txd2",		[0] = F_RGMII),
+	EIC7700_PIN(39,  "rgmii0_txd3",		[0] = F_RGMII),
+	EIC7700_PIN(40,  "i2s0_bclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(41,  "i2s0_wclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(42,  "i2s0_sdi",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(43,  "i2s0_sdo",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(44,  "i2s_mclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(45,  "rgmii0_rxclk",	[0] = F_RGMII),
+	EIC7700_PIN(46,  "rgmii0_rxdv",		[0] = F_RGMII),
+	EIC7700_PIN(47,  "rgmii0_rxd0",		[0] = F_RGMII),
+	EIC7700_PIN(48,  "rgmii0_rxd1",		[0] = F_RGMII),
+	EIC7700_PIN(49,  "rgmii0_rxd2",		[0] = F_RGMII),
+	EIC7700_PIN(50,  "rgmii0_rxd3",		[0] = F_RGMII),
+	EIC7700_PIN(51,  "i2s2_bclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(52,  "i2s2_wclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(53,  "i2s2_sdi",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(54,  "i2s2_sdo",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(55,  "gpio27",		[0] = F_GPIO, [1] = F_SATA),
+	EIC7700_PIN(56,  "gpio28",		[0] = F_GPIO),
+	EIC7700_PIN(57,  "gpio29",		[0] = F_RESET, [1] = F_EMMC, [2] = F_GPIO),
+	EIC7700_PIN(58,  "rgmii0_mdc",		[0] = F_RGMII),
+	EIC7700_PIN(59,  "rgmii0_mdio",		[0] = F_RGMII),
+	EIC7700_PIN(60,  "rgmii0_intb",		[0] = F_RGMII),
+	EIC7700_PIN(61,  "rgmii1_clk_125",	[0] = F_RGMII),
+	EIC7700_PIN(62,  "rgmii1_txen",		[0] = F_RGMII),
+	EIC7700_PIN(63,  "rgmii1_txclk",	[0] = F_RGMII),
+	EIC7700_PIN(64,  "rgmii1_txd0",		[0] = F_RGMII),
+	EIC7700_PIN(65,  "rgmii1_txd1",		[0] = F_RGMII),
+	EIC7700_PIN(66,  "rgmii1_txd2",		[0] = F_RGMII),
+	EIC7700_PIN(67,  "rgmii1_txd3",		[0] = F_RGMII),
+	EIC7700_PIN(68,  "i2s1_bclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(69,  "i2s1_wclk",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(70,  "i2s1_sdi",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(71,  "i2s1_sdo",		[0] = F_I2S, [2] = F_GPIO),
+	EIC7700_PIN(72,  "gpio34",		[0] = F_RESET, [1] = F_SDIO, [2] = F_GPIO),
+	EIC7700_PIN(73,  "rgmii1_rxclk",	[0] = F_RGMII),
+	EIC7700_PIN(74,  "rgmii1_rxdv",		[0] = F_RGMII),
+	EIC7700_PIN(75,  "rgmii1_rxd0",		[0] = F_RGMII),
+	EIC7700_PIN(76,  "rgmii1_rxd1",		[0] = F_RGMII),
+	EIC7700_PIN(77,  "rgmii1_rxd2",		[0] = F_RGMII),
+	EIC7700_PIN(78,  "rgmii1_rxd3",		[0] = F_RGMII),
+	EIC7700_PIN(79,  "spi1_cs0_n",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(80,  "spi1_clk",        [0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(81,  "spi1_d0", [0] = F_SPI, [1] = F_I2C, [2] = F_GPIO, [3] = F_UART),
+	EIC7700_PIN(82,  "spi1_d1", [0] = F_SPI, [1] = F_I2C, [2] = F_GPIO, [3] = F_UART),
+	EIC7700_PIN(83,  "spi1_d2",		[0] = F_SPI, [1] = F_SDIO, [2] = F_GPIO),
+	EIC7700_PIN(84,  "spi1_d3",		[0] = F_SPI, [1] = F_PWM, [2] = F_GPIO),
+	EIC7700_PIN(85,  "spi1_cs1_n",		[0] = F_SPI, [1] = F_PWM, [2] = F_GPIO),
+	EIC7700_PIN(86,  "rgmii1_mdc",		[0] = F_RGMII),
+	EIC7700_PIN(87,  "rgmii1_mdio",		[0] = F_RGMII),
+	EIC7700_PIN(88,  "rgmii1_intb",		[0] = F_RGMII),
+	EIC7700_PIN(89,  "usb0_pwren",		[0] = F_USB, [2] = F_GPIO),
+	EIC7700_PIN(90,  "usb1_pwren",		[0] = F_USB, [2] = F_GPIO),
+	EIC7700_PIN(91,  "i2c0_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(92,  "i2c0_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(93,  "i2c1_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(94,  "i2c1_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(95,  "i2c2_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(96,  "i2c2_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(97,  "i2c3_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(98,  "i2c3_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(99,  "i2c4_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(100, "i2c4_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(101, "i2c5_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(102, "i2c5_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(103, "uart0_tx",		[0] = F_UART, [2] = F_GPIO),
+	EIC7700_PIN(104, "uart0_rx",		[0] = F_UART, [2] = F_GPIO),
+	EIC7700_PIN(105, "uart1_tx",		[0] = F_UART, [2] = F_GPIO),
+	EIC7700_PIN(106, "uart1_rx",		[0] = F_UART, [2] = F_GPIO),
+	EIC7700_PIN(107, "uart1_cts",		[0] = F_UART, [1] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(108, "uart1_rts",		[0] = F_UART, [1] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(109, "uart2_tx",		[0] = F_UART, [1] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(110, "uart2_rx",		[0] = F_UART, [1] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(111, "jtag2_tck",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(112, "jtag2_tms",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(113, "jtag2_tdi",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(114, "jtag2_tdo",		[0] = F_JTAG, [2] = F_GPIO),
+	EIC7700_PIN(115, "fan_pwm",		[0] = F_PWM, [2] = F_GPIO),
+	EIC7700_PIN(116, "fan_tach",		[0] = F_FAN_TACH, [2] = F_GPIO),
+	EIC7700_PIN(117, "mipi_csi0_xvs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(118, "mipi_csi0_xhs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(119, "mipi_csi0_mclk",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(120, "mipi_csi1_xvs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(121, "mipi_csi1_xhs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(122, "mipi_csi1_mclk",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(123, "mipi_csi2_xvs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(124, "mipi_csi2_xhs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(125, "mipi_csi2_mclk",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(126, "mipi_csi3_xvs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(127, "mipi_csi3_xhs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(128, "mipi_csi3_mclk",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(129, "mipi_csi4_xvs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(130, "mipi_csi4_xhs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(131, "mipi_csi4_mclk",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(132, "mipi_csi5_xvs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(133, "mipi_csi5_xhs",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(134, "mipi_csi5_mclk",	[0] = F_MIPI_CSI, [2] = F_GPIO),
+	EIC7700_PIN(135, "spi3_cs_n",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(136, "spi3_clk",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(137, "spi3_di",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(138, "spi3_do",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(139, "gpio92",	[0] = F_I2C, [1] = F_MIPI_CSI, [2] = F_GPIO, [3] = F_UART),
+	EIC7700_PIN(140, "gpio93",	[0] = F_I2C, [1] = F_MIPI_CSI, [2] = F_GPIO, [3] = F_UART),
+	EIC7700_PIN(141, "s_mode",		[0] = F_S_MODE, [2] = F_GPIO),
+	EIC7700_PIN(142, "gpio95",		[0] = F_DDR_REF_CLK_SEL, [2] = F_GPIO),
+	EIC7700_PIN(143, "spi0_cs_n",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(144, "spi0_clk",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(145, "spi0_d0",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(146, "spi0_d1",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(147, "spi0_d2",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(148, "spi0_d3",		[0] = F_SPI, [2] = F_GPIO),
+	EIC7700_PIN(149, "i2c10_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(150, "i2c10_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(151, "i2c11_scl",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(152, "i2c11_sda",		[0] = F_I2C, [2] = F_GPIO),
+	EIC7700_PIN(153, "gpio106",		[0] = F_GPIO),
+	EIC7700_PIN(154, "boot_sel0",		[0] = F_BOOT_SEL, [2] = F_GPIO),
+	EIC7700_PIN(155, "boot_sel1",		[0] = F_BOOT_SEL, [2] = F_GPIO),
+	EIC7700_PIN(156, "boot_sel2",		[0] = F_BOOT_SEL, [2] = F_GPIO),
+	EIC7700_PIN(157, "boot_sel3",		[0] = F_BOOT_SEL, [2] = F_GPIO),
+	EIC7700_PIN(158, "gpio111",		[0] = F_GPIO),
+	EIC7700_PIN(159, "reserved0",		[0] = F_DISABLED),
+	EIC7700_PIN(160, "reserved1",		[0] = F_DISABLED),
+	EIC7700_PIN(161, "reserved2",		[0] = F_DISABLED),
+	EIC7700_PIN(162, "reserved3",		[0] = F_DISABLED),
+	EIC7700_PIN(163, "lpddr_ref_clk",		[0] = F_LPDDR_REF_CLK),
+};
+
+static int eic7700_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+
+	return pc->desc.npins;
+}
+
+static const char *eic7700_get_group_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+
+	return pc->desc.pins[selector].name;
+}
+
+static int eic7700_get_group_pins(struct pinctrl_dev *pctldev, unsigned int selector,
+				  const unsigned int **pins, unsigned int *npins)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+
+	*pins = &pc->desc.pins[selector].number;
+	*npins = 1;
+
+	return 0;
+}
+
+static const struct pinctrl_ops eic7700_pinctrl_ops = {
+	.get_groups_count	= eic7700_get_groups_count,
+	.get_group_name		= eic7700_get_group_name,
+	.get_group_pins		= eic7700_get_group_pins,
+#ifdef CONFIG_OF
+	.dt_node_to_map		= pinconf_generic_dt_node_to_map_pin,
+	.dt_free_map		= pinconf_generic_dt_free_map,
+#endif
+};
+
+static int eic7700_pin_config_get(struct pinctrl_dev *pctldev, unsigned int pin,
+				  unsigned long *config)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+	const struct eic7700_pin *pin_data = pc->desc.pins[pin].drv_data;
+	u32 arg, value;
+	int param;
+
+	if (pin_data->functions[0] == F_OSC || pin_data->functions[0] == F_DISABLED)
+		return -EOPNOTSUPP;
+
+	value = readl_relaxed(pc->base + EIC7700_PIN_REG(pin));
+
+	param = pinconf_to_config_param(*config);
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+		arg = (value & EIC7700_BIAS) == 0;
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		arg = (value & EIC7700_BIAS) == EIC7700_PD;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		arg = (value & EIC7700_BIAS) == EIC7700_PU;
+		break;
+	case PIN_CONFIG_DRIVE_STRENGTH_UA:
+		if (pin_data->functions[0] == F_RGMII ||
+			pin_data->functions[0] == F_LPDDR_REF_CLK)
+			arg = FIELD_GET(EIC7700_DS, value) * 3000 + 3000;
+		else
+			arg = FIELD_GET(EIC7700_DS, value) * 3000 + 6000;
+		break;
+	case PIN_CONFIG_INPUT_ENABLE:
+		arg = value & EIC7700_IE;
+		break;
+	case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+		arg = value & EIC7700_ST;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	*config = pinconf_to_config_packed(param, arg);
+	return arg ? 0 : -EINVAL;
+}
+
+static int eic7700_pin_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
+				  unsigned long *configs, unsigned int num_configs)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+	const struct eic7700_pin *pin_data = pc->desc.pins[pin].drv_data;
+	u32 value;
+
+	if (pin_data->functions[0] == F_OSC || pin_data->functions[0] == F_DISABLED)
+		return -EOPNOTSUPP;
+
+	value = readl_relaxed(pc->base + EIC7700_PIN_REG(pin));
+
+	for (unsigned int i = 0; i < num_configs; i++) {
+		int param = pinconf_to_config_param(configs[i]);
+		u32 arg = pinconf_to_config_argument(configs[i]);
+
+		switch (param) {
+		case PIN_CONFIG_BIAS_DISABLE:
+			value &= ~EIC7700_BIAS;
+			break;
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			if (arg == 0)
+				return -EOPNOTSUPP;
+			value &= ~EIC7700_BIAS;
+			value |= EIC7700_PD;
+			break;
+		case PIN_CONFIG_BIAS_PULL_UP:
+			if (arg == 0)
+				return -EOPNOTSUPP;
+			value &= ~EIC7700_BIAS;
+			value |= EIC7700_PU;
+			break;
+		case PIN_CONFIG_DRIVE_STRENGTH_UA:
+			value &= ~EIC7700_DS;
+			if (pin_data->functions[0] == F_RGMII ||
+				pin_data->functions[0] == F_LPDDR_REF_CLK) {
+				if (arg < 3000 || arg > 24000)
+					return -EOPNOTSUPP;
+				value |= FIELD_PREP(EIC7700_DS, (arg - 3000) / 3000);
+			} else {
+				if (arg < 6000 || arg > 27000)
+					return -EOPNOTSUPP;
+				value |= FIELD_PREP(EIC7700_DS, (arg - 6000) / 3000);
+			}
+			break;
+		case PIN_CONFIG_INPUT_ENABLE:
+			if (arg)
+				value |= EIC7700_IE;
+			else
+				value &= ~EIC7700_IE;
+			break;
+		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+			if (arg)
+				value |= EIC7700_ST;
+			else
+				value &= ~EIC7700_ST;
+			break;
+		default:
+			return -EOPNOTSUPP;
+		}
+	}
+
+	writel_relaxed(value, pc->base + EIC7700_PIN_REG(pin));
+
+	return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void eic7700_pin_config_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
+					unsigned int pin)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+	u32 value = readl_relaxed(pc->base + EIC7700_PIN_REG(pin)) & EIC7700_PINCONF;
+
+	seq_printf(s, " [0x%02x]", value);
+}
+#else
+#define eic7700_pin_config_dbg_show NULL
+#endif
+
+static const struct pinconf_ops eic7700_pinconf_ops = {
+	.is_generic			= true,
+	.pin_config_get			= eic7700_pin_config_get,
+	.pin_config_set			= eic7700_pin_config_set,
+	.pin_config_group_get		= eic7700_pin_config_get,
+	.pin_config_group_set		= eic7700_pin_config_set,
+	.pin_config_dbg_show		= eic7700_pin_config_dbg_show,
+	.pin_config_group_dbg_show	= eic7700_pin_config_dbg_show,
+};
+
+static int eic7700_get_functions_count(struct pinctrl_dev *pctldev)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+
+	return pc->functions_count;
+}
+
+static const char *eic7700_get_function_name(struct pinctrl_dev *pctldev, unsigned int selector)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+
+	return pc->functions[selector].name;
+}
+
+static int eic7700_get_function_groups(struct pinctrl_dev *pctldev, unsigned int selector,
+				       const char *const **groups, unsigned int *num_groups)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+
+	*groups = pc->functions[selector].groups;
+	*num_groups = pc->functions[selector].ngroups;
+
+	return 0;
+}
+
+static int eic7700_set_mux(struct pinctrl_dev *pctldev, unsigned int func_selector,
+			   unsigned int group_selector)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+	const struct eic7700_pin *pin_data = pc->desc.pins[group_selector].drv_data;
+	u32 fs, value;
+
+	if (pin_data->functions[0] == F_OSC || pin_data->functions[0] == F_DISABLED)
+		return -EOPNOTSUPP;
+
+	for (fs = 0; fs < EIC7700_FUNCTIONS_PER_PIN; fs++)
+		if (pin_data->functions[fs] == func_selector)
+			break;
+
+	if (fs == EIC7700_FUNCTIONS_PER_PIN) {
+		dev_err(pctldev->dev, "invalid mux %s for pin %s\n",
+			pc->functions[func_selector].name,
+			pc->desc.pins[group_selector].name);
+		return -EINVAL;
+	}
+
+	value = readl_relaxed(pc->base + EIC7700_PIN_REG(group_selector));
+	value &= ~EIC7700_FUNC_SEL;
+	value |= FIELD_PREP(EIC7700_FUNC_SEL, fs);
+	writel_relaxed(value, pc->base + EIC7700_PIN_REG(group_selector));
+
+	return 0;
+}
+
+static int eic7700_gpio_request_enable(struct pinctrl_dev *pctldev,
+				       struct pinctrl_gpio_range *range, unsigned int offset)
+{
+	return eic7700_set_mux(pctldev, F_GPIO, offset);
+}
+
+static void eic7700_gpio_disable_free(struct pinctrl_dev *pctldev,
+				      struct pinctrl_gpio_range *range, unsigned int offset)
+{
+	eic7700_set_mux(pctldev, F_DISABLED, offset);
+}
+
+static int eic7700_gpio_set_direction(struct pinctrl_dev *pctldev,
+				      struct pinctrl_gpio_range *range, unsigned int offset,
+				      bool input)
+{
+	struct eic7700_pinctrl *pc = pinctrl_dev_get_drvdata(pctldev);
+	u32 value;
+
+	value = readl_relaxed(pc->base + EIC7700_PIN_REG(offset));
+	if (input)
+		value |= EIC7700_IE;
+	else
+		value &= ~EIC7700_IE;
+	writel_relaxed(value, pc->base + EIC7700_PIN_REG(offset));
+
+	return 0;
+}
+
+static const struct pinmux_ops eic7700_pinmux_ops = {
+	.get_functions_count	= eic7700_get_functions_count,
+	.get_function_name	= eic7700_get_function_name,
+	.get_function_groups	= eic7700_get_function_groups,
+	.set_mux		= eic7700_set_mux,
+	.gpio_request_enable	= eic7700_gpio_request_enable,
+	.gpio_disable_free	= eic7700_gpio_disable_free,
+	.gpio_set_direction	= eic7700_gpio_set_direction,
+	.strict			= true,
+};
+
+static int eic7700_pinctrl_init_function_groups(struct device *dev, struct eic7700_pinctrl *pc,
+						const char *const *function_names)
+{
+	unsigned int ngroups = 0;
+	const char **groups;
+
+	/* Count the number of groups for each function */
+	for (unsigned int pin = 0; pin < pc->desc.npins; pin++) {
+		const struct eic7700_pin *pin_data = pc->desc.pins[pin].drv_data;
+		bool found_disabled = false;
+
+		for (unsigned int fs = 0; fs < EIC7700_FUNCTIONS_PER_PIN; fs++) {
+			unsigned int selector = pin_data->functions[fs];
+			struct pinfunction *function = &pc->functions[selector];
+
+			/* Only count F_DISABLED once per pin */
+			if (selector == F_DISABLED) {
+				if (found_disabled)
+					continue;
+				found_disabled = true;
+			}
+
+			function->ngroups++;
+			ngroups++;
+		}
+	}
+
+	groups = devm_kcalloc(dev, ngroups, sizeof(*groups), GFP_KERNEL);
+	if (!groups)
+		return -ENOMEM;
+
+	for (unsigned int selector = 0; selector < pc->functions_count; selector++) {
+		struct pinfunction *function = &pc->functions[selector];
+
+		function->name = function_names[selector];
+		function->groups = groups;
+		groups += function->ngroups;
+
+		/* Reset per-function ngroups for use as iterator below */
+		function->ngroups = 0;
+	}
+
+	/* Fill in the group pointers for each function */
+	for (unsigned int pin = 0; pin < pc->desc.npins; pin++) {
+		const struct pinctrl_pin_desc *desc = &pc->desc.pins[pin];
+		const struct eic7700_pin *pin_data = desc->drv_data;
+		bool found_disabled = false;
+
+		for (unsigned int fs = 0; fs < EIC7700_FUNCTIONS_PER_PIN; fs++) {
+			unsigned int selector = pin_data->functions[fs];
+			struct pinfunction *function = &pc->functions[selector];
+
+			/* Only count F_DISABLED once per pin */
+			if (selector == F_DISABLED) {
+				if (found_disabled)
+					continue;
+				found_disabled = true;
+			}
+
+			((const char **)function->groups)[function->ngroups++] = desc->name;
+		}
+	}
+
+	return 0;
+}
+
+static int eic7700_pinctrl_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct pinctrl_dev *pctldev;
+	struct eic7700_pinctrl *pc;
+	struct regulator *regulator;
+	u32 voltage, rgmii0_mode, rgmii1_mode;
+	int ret;
+
+	pc = devm_kzalloc(dev, struct_size(pc, functions, EIC7700_FUNCTIONS_COUNT), GFP_KERNEL);
+	if (!pc)
+		return -ENOMEM;
+
+	pc->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(pc->base))
+		return PTR_ERR(pc->base);
+
+	regulator = devm_regulator_get(dev, "vrgmii");
+	if (IS_ERR_OR_NULL(regulator)) {
+		return dev_err_probe(dev, PTR_ERR(regulator),
+					 "failed to get vrgmii regulator\n");
+	}
+
+	voltage = regulator_get_voltage(regulator);
+	if (voltage < 0) {
+		return dev_err_probe(&pdev->dev, voltage,
+			 "Failed to get voltage from regulator\n");
+	}
+
+	rgmii0_mode = readl_relaxed(pc->base + EIC7700_RGMII0_SEL_MODE);
+	rgmii1_mode = readl_relaxed(pc->base + EIC7700_RGMII1_SEL_MODE);
+	rgmii0_mode &= ~EIC7700_MS;
+	rgmii1_mode &= ~EIC7700_MS;
+	if (voltage == 1800000) {
+		rgmii0_mode |= FIELD_PREP(EIC7700_MS, EIC7700_MS_1V8);
+		rgmii1_mode |= FIELD_PREP(EIC7700_MS, EIC7700_MS_1V8);
+	} else if (voltage == 3300000) {
+		rgmii0_mode |= FIELD_PREP(EIC7700_MS, EIC7700_MS_3V3);
+		rgmii1_mode |= FIELD_PREP(EIC7700_MS, EIC7700_MS_3V3);
+	} else {
+		return dev_err_probe(&pdev->dev, -EINVAL,
+			 "Invalid voltage configuration, should be either 1.8V or 3.3V\n");
+	}
+
+	writel_relaxed(rgmii0_mode, pc->base + EIC7700_RGMII0_SEL_MODE);
+	writel_relaxed(rgmii1_mode, pc->base + EIC7700_RGMII1_SEL_MODE);
+
+	pc->desc.name = dev_name(dev);
+	pc->desc.pins = eic7700_pins;
+	pc->desc.npins = ARRAY_SIZE(eic7700_pins);
+	pc->desc.pctlops = &eic7700_pinctrl_ops;
+	pc->desc.pmxops = &eic7700_pinmux_ops;
+	pc->desc.confops = &eic7700_pinconf_ops;
+	pc->desc.owner = THIS_MODULE;
+
+	pc->functions_count = EIC7700_FUNCTIONS_COUNT;
+	ret = eic7700_pinctrl_init_function_groups(dev, pc, eic7700_functions);
+	if (ret)
+		return ret;
+
+	ret = devm_pinctrl_register_and_init(dev, &pc->desc, pc, &pctldev);
+	if (ret)
+		return dev_err_probe(dev, ret, "could not register pinctrl driver\n");
+
+	return pinctrl_enable(pctldev);
+}
+
+static const struct of_device_id eic7700_pinctrl_of_match[] = {
+	{ .compatible = "eswin,eic7700-pinctrl" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, eic7700_pinctrl_of_match);
+
+static struct platform_driver eic7700_pinctrl_driver = {
+	.probe	= eic7700_pinctrl_probe,
+	.driver	= {
+		.name		= "pinctrl-eic7700",
+		.of_match_table	= eic7700_pinctrl_of_match,
+	},
+};
+module_platform_driver(eic7700_pinctrl_driver);
+
+MODULE_DESCRIPTION("Pinctrl driver for the ESWIN EIC7700 SoC");
+MODULE_AUTHOR("Samuel Holland <samuel.holland@sifive.com>");
+MODULE_AUTHOR("Yulin Lu <luyulin@eswincomputing.com>");
+MODULE_LICENSE("GPL");
-- 
2.25.1

Re: [PATCH v5 0/2] ESWIN EIC7700 pinctrl driver

[Linus Walleij]

On Thu, Jun 12, 2025 at 12:45 PM Yulin Lu <luyulin@eswincomputing.com> wrote:

>   Implements support for the Eswin eic7700 SoC pinctrl controller.
>   Provides API to manage pinctrl for the eic7700 SoC.
>   Integration with the Linux pinctrl subsystem for consistency and
>   scalability.
>
>   Supported chips:
>     Eswin eic7700 SoC.
>
>   Test:
>     Tested this patch on the Sifive HiFive Premier P550 (which uses
>     the EIC7700 SoC), including system boot, networking, EMMC, display,
>     and other peripherals. The drivers for these modules all use the
>     pinctrl module, so this verifies that this pinctrl driver
>     patch is working properly.

This v5 patch set applied, any further comments or snags can certainly
be addressed in-tree.

Yours,
Linus Walleij