linux-gpio.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Vignesh Raghavendra <vigneshr@ti.com>, Nishanth Menon <nm@ti.com>,
	Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
	Bryan Brattlof <bb@ti.com>
Subject: Re: [PATCH 4/4] arm64: dts: ti: Add support for AM62A7-SK
Date: Tue, 30 Aug 2022 12:57:17 +0300	[thread overview]
Message-ID: <323dc2e1-68fb-df0c-38b0-5af6d087248e@linaro.org> (raw)
In-Reply-To: <20220829082200.241653-5-vigneshr@ti.com>

On 29/08/2022 11:22, Vignesh Raghavendra wrote:
> AM62A StarterKit (SK) board is a low cost, small form factor board
> designed for TI’s AM62A7 SoC. It supports the following interfaces:
> * 2 GB LPDDR4 RAM
> * x1 Gigabit Ethernet interface
> * x1 HDMI Port with audio
> * x1 Headphone Jack
> * x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
> * x1 UHS-1 capable µSD card slot
> * M.2 SDIO Wifi + UART slot
> * 1Gb OSPI NAND flash
> * x4 UART through UART-USB bridge
> * XDS110 for onboard JTAG debug using USB
> * Temperature sensors, user push buttons and LEDs
> * 40-pin User Expansion Connector
> * 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
> * 20-pin header for Programmable Realtime Unit (PRU) IO pins
> * 40-pin CSI header
> 
> Add basic support for AM62A7-SK.
> 
> Schematics: https://www.ti.com/lit/zip/sprr459
> 
> Co-developed-by: Bryan Brattlof <bb@ti.com>
> Signed-off-by: Bryan Brattlof <bb@ti.com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---
>  arch/arm64/boot/dts/ti/Makefile         |   2 +
>  arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 224 ++++++++++++++++++++++++
>  2 files changed, 226 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> 
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 02e5d80344d0..4555a5be2257 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -23,3 +23,5 @@ dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
>  dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>  
>  dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
> +
> +dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> new file mode 100644
> index 000000000000..994ed6865551
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
> @@ -0,0 +1,224 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * AM62A SK: https://www.ti.com/lit/zip/sprr459
> + *
> + * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-am62a7.dtsi"
> +
> +/ {
> +	compatible =  "ti,am62a7-sk", "ti,am62a7";
> +	model = "Texas Instruments AM62A7 SK";
> +
> +	aliases {
> +		serial2 = &main_uart0;
> +		mmc1 = &sdhci1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial2:115200n8";
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		/* 2G RAM */
> +		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
> +

No need for blank line.

With that:

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

      reply	other threads:[~2022-08-30  9:59 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-29  8:21 [PATCH 0/4] arm64: dts: ti: Add support for AM62A family of SoCs Vignesh Raghavendra
2022-08-29  8:21 ` [PATCH 1/4] dt-bindings: arm: ti: Add bindings for AM62A7 SoC Vignesh Raghavendra
2022-08-30  9:52   ` Krzysztof Kozlowski
2022-09-01  5:30     ` Vignesh Raghavendra
2022-08-29  8:21 ` [PATCH 2/4] dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62A Vignesh Raghavendra
2022-08-30  9:53   ` Krzysztof Kozlowski
2022-09-01  5:32     ` Vignesh Raghavendra
2022-08-31 13:37   ` Linus Walleij
2022-08-29  8:21 ` [PATCH 3/4] arm64: dts: ti: Introduce AM62A7 family of SoCs Vignesh Raghavendra
2022-08-30  9:56   ` Krzysztof Kozlowski
2022-09-01  5:39     ` Vignesh Raghavendra
2022-08-29  8:22 ` [PATCH 4/4] arm64: dts: ti: Add support for AM62A7-SK Vignesh Raghavendra
2022-08-30  9:57   ` Krzysztof Kozlowski [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=323dc2e1-68fb-df0c-38b0-5af6d087248e@linaro.org \
    --to=krzysztof.kozlowski@linaro.org \
    --cc=bb@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=kristo@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).