Re: [PATCH] pinctrl: rockchip: fix reading pull type on rk3568

["Heiko Stübner" <heiko@sntech.de>]

Hi Jay,

Am Mittwoch, 11. Januar 2023, 11:26:18 CET schrieb jay.xu@rock-chips.com:
> Hi Jonas
> 
> --------------
> jay.xu@rock-chips.com
> >When reading pinconf-pins from debugfs it fails to get the configured pull
> >type on RK3568, "unsupported pinctrl type" error messages is also reported.
> >
> >Fix this by adding support for RK3568 in rockchip_get_pull, including a
> >reverse of the pull-up value swap applied in rockchip_set_pull so that
> >pull-up is correctly reported in pinconf-pins.
> >Also update the workaround comment to reflect affected pins, GPIO0_D3-D6.
> >
> >Fixes: c0dadc0e47a8 ("pinctrl: rockchip: add support for rk3568")
> >Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
> >--- 
> 
> Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>

Did you want one of

- Reviewed-by:
- Tested-by:
- Acked-by:

instead?


Heiko

> > drivers/pinctrl/pinctrl-rockchip.c | 11 ++++++++++-
> > 1 file changed, 10 insertions(+), 1 deletion(-)
> >
> >diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
> >index 849d5fa2a362..5eeac92f610a 100644
> >--- a/drivers/pinctrl/pinctrl-rockchip.c
> >+++ b/drivers/pinctrl/pinctrl-rockchip.c
> >@@ -2436,10 +2436,19 @@ static int rockchip_get_pull(struct rockchip_pin_bank *bank, int pin_num)
> > case RK3308:
> > case RK3368:
> > case RK3399:
> >+	case RK3568:
> > case RK3588:
> > pull_type = bank->pull_type[pin_num / 8];
> > data >>= bit;
> > data &= (1 << RK3188_PULL_BITS_PER_PIN) - 1;
> >+	/*
> >+	* In the TRM, pull-up being 1 for everything except the GPIO0_D3-D6,
> >+	* where that pull up value becomes 3.
> >+	*/
> >+	if (ctrl->type == RK3568 && bank->bank_num == 0 && pin_num >= 27 && pin_num <= 30) {
> >+	if (data == 3)
> >+	data = 1;
> >+	}
> >
> > return rockchip_pull_list[pull_type][data];
> > default:
> >@@ -2497,7 +2506,7 @@ static int rockchip_set_pull(struct rockchip_pin_bank *bank,
> > }
> > }
> > /*
> >-	* In the TRM, pull-up being 1 for everything except the GPIO0_D0-D6,
> >+	* In the TRM, pull-up being 1 for everything except the GPIO0_D3-D6,
> > * where that pull up value becomes 3.
> > */
> > if (ctrl->type == RK3568 && bank->bank_num == 0 && pin_num >= 27 && pin_num <= 30) {
> >--
> >2.39.0
> >
>