[PATCH v2 00/33] pinctrl/arm64: qcom: continued - fix Qualcomm TLMM pinctrl schema warnings

[PATCH v2 00/33] pinctrl/arm64: qcom: continued - fix Qualcomm TLMM pinctrl schema warnings

[Krzysztof Kozlowski]

Hi,

Changes since v1
================
v1: https://lore.kernel.org/linux-devicetree/20220924080459.13084-1-krzysztof.kozlowski@linaro.org/T/#t
1. As Stephan suggested, move check for function on non-GPIO pins to common
   TLMM schema.  This affects few commits in the set named:
   "use common TLMM schema"
   "do not require function on non-GPIOs"

Overview
========
This is the third, independent patchset around Qualcomm pinctrl in recent days:
1. First round of TLMM fixes: merged
2. LPASS fixes:
   https://lore.kernel.org/linux-devicetree/20220922195651.345369-1-krzysztof.kozlowski@linaro.org/T/#t
3. ARMv7 TLMM fixes: *THIS PATCHSET*
4. ARMv8 remaining TLMM fixes: v1 send:
   https://lore.kernel.org/linux-devicetree/20220925110608.145728-1-krzysztof.kozlowski@linaro.org/T/#t

Dependencies
============
1. No dependencies.
2. dt-bindings are independent of DTS patches.

Best regards,
Krzysztof

Krzysztof Kozlowski (33):
  arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins
  arm64: dts: qcom: ipq6018: align TLMM pin configuration with DT schema
  ARM: dts: qcom: sdx55: add gpio-ranges to TLMM pinctrl
  ARM: dts: qcom: sdx55: align TLMM pin configuration with DT schema
  ARM: dts: qcom: msm8226: align TLMM pin configuration with DT schema
  ARM: dts: qcom: msm8974: align TLMM pin configuration with DT schema
  dt-bindings: pinctrl: qcom,tlmm-common: add common check for function
  dt-bindings: pinctrl: qcom,ipq6018: add qpic_pad function
  dt-bindings: pinctrl: qcom,ipq6018: increase number of pins in pinmux
  dt-bindings: pinctrl: qcom,ipq6018: fix matching pin config
  dt-bindings: pinctrl: qcom,ipq6018: use common TLMM schema
  dt-bindings: pinctrl: qcom,ipq6018: fix indentation in example
  dt-bindings: pinctrl: qcom,msm8226: fix matching pin config
  dt-bindings: pinctrl: qcom,msm8226: use common TLMM schema
  dt-bindings: pinctrl: qcom,msm8226: add functions and input-enable
  dt-bindings: pinctrl: qcom,msm8226: fix indentation in example
  dt-bindings: pinctrl: qcom,msm8909-tlmm: fix matching pin config
  dt-bindings: pinctrl: qcom,msm8909-tlmm: do not require function on
    non-GPIOs
  dt-bindings: pinctrl: qcom,msm8909-tlmm: fix indentation in example
  dt-bindings: pinctrl: qcom,msm8953: fix matching pin config
  dt-bindings: pinctrl: qcom,msm8953: use common TLMM schema
  dt-bindings: pinctrl: qcom,msm8953: fix indentation in example
  dt-bindings: pinctrl: qcom,mdm9607: do not require function on
    non-GPIOs
  dt-bindings: pinctrl: qcom,mdm9607: fix indentation in example
  dt-bindings: pinctrl: qcom,qcm2290: fix matching pin config
  dt-bindings: pinctrl: qcom,qcm2290: use common TLMM schema
  dt-bindings: pinctrl: qcom,sdx55: fix matching pin config
  dt-bindings: pinctrl: qcom,sdx55: use common TLMM schema
  dt-bindings: pinctrl: qcom,sdx55: fix indentation in example
  dt-bindings: pinctrl: qcom,sdx65: fix matching pin config
  dt-bindings: pinctrl: qcom,sdx65: use common TLMM schema
  dt-bindings: pinctrl: qcom,sc7280: fix matching pin config
  dt-bindings: pinctrl: qcom,sc8280xp: fix indentation in example
    (remaining piece)

 .../pinctrl/qcom,ipq6018-pinctrl.yaml         | 60 +++++++++--------
 .../pinctrl/qcom,mdm9607-pinctrl.yaml         | 23 ++++---
 .../pinctrl/qcom,msm8226-pinctrl.yaml         | 63 +++++++++---------
 .../bindings/pinctrl/qcom,msm8909-tlmm.yaml   | 64 +++++++++----------
 .../pinctrl/qcom,msm8953-pinctrl.yaml         | 51 ++++++++-------
 .../pinctrl/qcom,qcm2290-pinctrl.yaml         | 11 ++--
 .../bindings/pinctrl/qcom,sc7280-pinctrl.yaml | 14 +++-
 .../pinctrl/qcom,sc8280xp-pinctrl.yaml        |  4 +-
 .../bindings/pinctrl/qcom,sdx55-pinctrl.yaml  | 51 ++++++++-------
 .../bindings/pinctrl/qcom,sdx65-pinctrl.yaml  | 12 ++--
 .../bindings/pinctrl/qcom,tlmm-common.yaml    | 20 ++++--
 arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts   |  6 +-
 arch/arm/boot/dts/qcom-msm8226.dtsi           | 24 +++----
 .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 30 ++++-----
 .../boot/dts/qcom-sdx55-telit-fn980-tlb.dts   | 45 +++++--------
 arch/arm/boot/dts/qcom-sdx55.dtsi             |  1 +
 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts  |  8 ++-
 arch/arm64/boot/dts/qcom/ipq6018.dtsi         |  4 +-
 18 files changed, 264 insertions(+), 227 deletions(-)

-- 
2.34.1

[PATCH v2 01/33] arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins

[Krzysztof Kozlowski]

When BLSPI1 (originally SPI0, later renamed in commit f82c48d46852
("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added,
the device node lacked respective pin configuration assignment.   It
used also blsp0_spi function but that was probably the same mistake as
naming it SPI0.

Fixes: 5bf635621245 ("arm64: dts: ipq6018: Add a few device nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
index 1ba2eca33c7b..afc2dc79767d 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -37,6 +37,8 @@ &blsp1_i2c3 {
 
 &blsp1_spi1 {
 	cs-select = <0>;
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	flash@0 {
@@ -57,7 +59,7 @@ i2c_1_pins: i2c-1-pins {
 
 	spi_0_pins: spi-0-pins {
 		pins = "gpio38", "gpio39", "gpio40", "gpio41";
-		function = "blsp0_spi";
+		function = "blsp1_spi";
 		drive-strength = <8>;
 		bias-pull-down;
 	};
-- 
2.34.1

Re: [PATCH v2 01/33] arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins

[Konrad Dybcio]

On 26.09.2022 09:43, Krzysztof Kozlowski wrote:
> When BLSPI1 (originally SPI0, later renamed in commit f82c48d46852
> ("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added,
> the device node lacked respective pin configuration assignment.   It
> used also blsp0_spi function but that was probably the same mistake as
> naming it SPI0.
> 
> Fixes: 5bf635621245 ("arm64: dts: ipq6018: Add a few device nodes")
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> index 1ba2eca33c7b..afc2dc79767d 100644
> --- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> @@ -37,6 +37,8 @@ &blsp1_i2c3 {
>  
>  &blsp1_spi1 {
>  	cs-select = <0>;
> +	pinctrl-0 = <&spi_0_pins>;
> +	pinctrl-names = "default";
>  	status = "okay";
>  
>  	flash@0 {
> @@ -57,7 +59,7 @@ i2c_1_pins: i2c-1-pins {
>  
>  	spi_0_pins: spi-0-pins {
>  		pins = "gpio38", "gpio39", "gpio40", "gpio41";
> -		function = "blsp0_spi";
> +		function = "blsp1_spi";
>  		drive-strength = <8>;
>  		bias-pull-down;
>  	};

Re: [PATCH v2 01/33] arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins

[Robert Marko]

On 26. 09. 2022. 09:43, Krzysztof Kozlowski wrote:
> When BLSPI1 (originally SPI0, later renamed in commit f82c48d46852
> ("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added,
> the device node lacked respective pin configuration assignment.   It
> used also blsp0_spi function but that was probably the same mistake as
> naming it SPI0.

Hi,

Sorry for making it confusing, but "blsp0_spi" is the correct function.
Pinctrl driver and datasheets call functions blsp0-blps5, but usually in DT
we call the nodes blsp1-blsp6.

It would probably be better for me to rename the nodes to blsp0-5 instead.

Regards,
Robert

>
> Fixes: 5bf635621245 ("arm64: dts: ipq6018: Add a few device nodes")
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 4 +++-
>   1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> index 1ba2eca33c7b..afc2dc79767d 100644
> --- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> @@ -37,6 +37,8 @@ &blsp1_i2c3 {
>   
>   &blsp1_spi1 {
>   	cs-select = <0>;
> +	pinctrl-0 = <&spi_0_pins>;
> +	pinctrl-names = "default";
>   	status = "okay";
>   
>   	flash@0 {
> @@ -57,7 +59,7 @@ i2c_1_pins: i2c-1-pins {
>   
>   	spi_0_pins: spi-0-pins {
>   		pins = "gpio38", "gpio39", "gpio40", "gpio41";
> -		function = "blsp0_spi";
> +		function = "blsp1_spi";
>   		drive-strength = <8>;
>   		bias-pull-down;
>   	};

Re: [PATCH v2 01/33] arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins

[Krzysztof Kozlowski]

On 27/09/2022 16:01, Robert Marko wrote:
> 
> On 26. 09. 2022. 09:43, Krzysztof Kozlowski wrote:
>> When BLSPI1 (originally SPI0, later renamed in commit f82c48d46852
>> ("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added,
>> the device node lacked respective pin configuration assignment.   It
>> used also blsp0_spi function but that was probably the same mistake as
>> naming it SPI0.
> 
> Hi,
> 
> Sorry for making it confusing, but "blsp0_spi" is the correct function.
> Pinctrl driver and datasheets call functions blsp0-blps5, but usually in DT
> we call the nodes blsp1-blsp6.
> 
> It would probably be better for me to rename the nodes to blsp0-5 instead.

OK, so instead I will add blsp0_spi to the bindings.

Best regards,
Krzysztof

Re: [PATCH v2 01/33] arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins

[Robert Marko]

On 27. 09. 2022. 16:33, Krzysztof Kozlowski wrote:
> On 27/09/2022 16:01, Robert Marko wrote:
>> On 26. 09. 2022. 09:43, Krzysztof Kozlowski wrote:
>>> When BLSPI1 (originally SPI0, later renamed in commit f82c48d46852
>>> ("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added,
>>> the device node lacked respective pin configuration assignment.   It
>>> used also blsp0_spi function but that was probably the same mistake as
>>> naming it SPI0.
>> Hi,
>>
>> Sorry for making it confusing, but "blsp0_spi" is the correct function.
>> Pinctrl driver and datasheets call functions blsp0-blps5, but usually in DT
>> we call the nodes blsp1-blsp6.
>>
>> It would probably be better for me to rename the nodes to blsp0-5 instead.
> OK, so instead I will add blsp0_spi to the bindings.

Can you add blsp0_uart and blsp0_i2c as well?
All 6 of the QUP-s have same features.

I am adding MDIO to CP01, so I can add mdc and mdio to bindings
as they are lacking there as well.

Regards,
Robert

>
> Best regards,
> Krzysztof
>

Re: [PATCH v2 01/33] arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins

[Krzysztof Kozlowski]

On 27/09/2022 17:20, Robert Marko wrote:
> 
> On 27. 09. 2022. 16:33, Krzysztof Kozlowski wrote:
>> On 27/09/2022 16:01, Robert Marko wrote:
>>> On 26. 09. 2022. 09:43, Krzysztof Kozlowski wrote:
>>>> When BLSPI1 (originally SPI0, later renamed in commit f82c48d46852
>>>> ("arm64: dts: qcom: ipq6018: correct QUP peripheral labels")) was added,
>>>> the device node lacked respective pin configuration assignment.   It
>>>> used also blsp0_spi function but that was probably the same mistake as
>>>> naming it SPI0.
>>> Hi,
>>>
>>> Sorry for making it confusing, but "blsp0_spi" is the correct function.
>>> Pinctrl driver and datasheets call functions blsp0-blps5, but usually in DT
>>> we call the nodes blsp1-blsp6.
>>>
>>> It would probably be better for me to rename the nodes to blsp0-5 instead.
>> OK, so instead I will add blsp0_spi to the bindings.
> 
> Can you add blsp0_uart and blsp0_i2c as well?
> All 6 of the QUP-s have same features.

Sure

Best regards,
Krzysztof

[PATCH v2 02/33] arm64: dts: qcom: ipq6018: align TLMM pin configuration with DT schema

[Krzysztof Kozlowski]

DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 4 ++--
 arch/arm64/boot/dts/qcom/ipq6018.dtsi        | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
index afc2dc79767d..e1fe7d598580 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -51,13 +51,13 @@ flash@0 {
 };
 
 &tlmm {
-	i2c_1_pins: i2c-1-pins {
+	i2c_1_pins: i2c-1-state {
 		pins = "gpio42", "gpio43";
 		function = "blsp2_i2c";
 		drive-strength = <8>;
 	};
 
-	spi_0_pins: spi-0-pins {
+	spi_0_pins: spi-0-state {
 		pins = "gpio38", "gpio39", "gpio40", "gpio41";
 		function = "blsp1_spi";
 		drive-strength = <8>;
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index a7c7ca980a71..9b9f778090e1 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -218,14 +218,14 @@ tlmm: pinctrl@1000000 {
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			serial_3_pins: serial3-pinmux {
+			serial_3_pins: serial3-state {
 				pins = "gpio44", "gpio45";
 				function = "blsp2_uart";
 				drive-strength = <8>;
 				bias-pull-down;
 			};
 
-			qpic_pins: qpic-pins {
+			qpic_pins: qpic-state {
 				pins = "gpio1", "gpio3", "gpio4",
 					"gpio5", "gpio6", "gpio7",
 					"gpio8", "gpio10", "gpio11",
-- 
2.34.1

Re: [PATCH v2 02/33] arm64: dts: qcom: ipq6018: align TLMM pin configuration with DT schema

[Konrad Dybcio]

On 26.09.2022 09:43, Krzysztof Kozlowski wrote:
> DT schema expects TLMM pin configuration nodes to be named with
> '-state' suffix and their optional children with '-pins' suffix.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 4 ++--
>  arch/arm64/boot/dts/qcom/ipq6018.dtsi        | 4 ++--
>  2 files changed, 4 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> index afc2dc79767d..e1fe7d598580 100644
> --- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
> @@ -51,13 +51,13 @@ flash@0 {
>  };
>  
>  &tlmm {
> -	i2c_1_pins: i2c-1-pins {
> +	i2c_1_pins: i2c-1-state {
>  		pins = "gpio42", "gpio43";
>  		function = "blsp2_i2c";
>  		drive-strength = <8>;
>  	};
>  
> -	spi_0_pins: spi-0-pins {
> +	spi_0_pins: spi-0-state {
>  		pins = "gpio38", "gpio39", "gpio40", "gpio41";
>  		function = "blsp1_spi";
>  		drive-strength = <8>;
> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> index a7c7ca980a71..9b9f778090e1 100644
> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> @@ -218,14 +218,14 @@ tlmm: pinctrl@1000000 {
>  			interrupt-controller;
>  			#interrupt-cells = <2>;
>  
> -			serial_3_pins: serial3-pinmux {
> +			serial_3_pins: serial3-state {
>  				pins = "gpio44", "gpio45";
>  				function = "blsp2_uart";
>  				drive-strength = <8>;
>  				bias-pull-down;
>  			};
>  
> -			qpic_pins: qpic-pins {
> +			qpic_pins: qpic-state {
>  				pins = "gpio1", "gpio3", "gpio4",
>  					"gpio5", "gpio6", "gpio7",
>  					"gpio8", "gpio10", "gpio11",

[PATCH v2 03/33] ARM: dts: qcom: sdx55: add gpio-ranges to TLMM pinctrl

[Krzysztof Kozlowski]

Add required gpio-ranges property to TLMM pinctrl node:

  qcom-sdx55-mtp.dtb: pinctrl@f100000: 'gpio-ranges' is a required property

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm/boot/dts/qcom-sdx55.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi
index c72540223fa9..f1c0dab40992 100644
--- a/arch/arm/boot/dts/qcom-sdx55.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx55.dtsi
@@ -559,6 +559,7 @@ tlmm: pinctrl@f100000 {
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 109>;
 		};
 
 		sram@1468f000 {
-- 
2.34.1

Re: [PATCH v2 03/33] ARM: dts: qcom: sdx55: add gpio-ranges to TLMM pinctrl

[Konrad Dybcio]

On 26.09.2022 09:43, Krzysztof Kozlowski wrote:
> Add required gpio-ranges property to TLMM pinctrl node:
> 
>   qcom-sdx55-mtp.dtb: pinctrl@f100000: 'gpio-ranges' is a required property
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  arch/arm/boot/dts/qcom-sdx55.dtsi | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi
> index c72540223fa9..f1c0dab40992 100644
> --- a/arch/arm/boot/dts/qcom-sdx55.dtsi
> +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi
> @@ -559,6 +559,7 @@ tlmm: pinctrl@f100000 {
>  			#gpio-cells = <2>;
>  			interrupt-controller;
>  			#interrupt-cells = <2>;
> +			gpio-ranges = <&tlmm 0 0 109>;
>  		};
>  
>  		sram@1468f000 {

[PATCH v2 04/33] ARM: dts: qcom: sdx55: align TLMM pin configuration with DT schema

[Krzysztof Kozlowski]

DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.  Schema
also requires 'function' property, so two nodes for the same gpio (mux
and config) should be merged into one.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../boot/dts/qcom-sdx55-telit-fn980-tlb.dts   | 45 +++++++------------
 1 file changed, 15 insertions(+), 30 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
index a4fa468a095f..ac8b4626ae9a 100644
--- a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
+++ b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
@@ -282,40 +282,25 @@ &remoteproc_mpss {
 };
 
 &tlmm {
-	pcie_ep_clkreq_default: pcie_ep_clkreq_default {
-		mux {
-			pins = "gpio56";
-			function = "pcie_clkreq";
-		};
-		config {
-			pins = "gpio56";
-			drive-strength = <2>;
-			bias-disable;
-		};
+	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
+		pins = "gpio56";
+		function = "pcie_clkreq";
+		drive-strength = <2>;
+		bias-disable;
 	};
 
-	pcie_ep_perst_default: pcie_ep_perst_default {
-		mux {
-			pins = "gpio57";
-			function = "gpio";
-		};
-		config {
-			pins = "gpio57";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
+	pcie_ep_perst_default: pcie-ep-perst-default-state {
+		pins = "gpio57";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
 	};
 
-	pcie_ep_wake_default: pcie_ep_wake_default {
-		mux {
-			pins = "gpio53";
-			function = "gpio";
-		};
-		config {
-			pins = "gpio53";
-			drive-strength = <2>;
-			bias-disable;
-		};
+	pcie_ep_wake_default: pcie-ep-wake-default-state {
+		pins = "gpio53";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
 	};
 };
 
-- 
2.34.1

Re: [PATCH v2 04/33] ARM: dts: qcom: sdx55: align TLMM pin configuration with DT schema

[Konrad Dybcio]

On 26.09.2022 09:43, Krzysztof Kozlowski wrote:
> DT schema expects TLMM pin configuration nodes to be named with
> '-state' suffix and their optional children with '-pins' suffix.  Schema
> also requires 'function' property, so two nodes for the same gpio (mux
> and config) should be merged into one.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  .../boot/dts/qcom-sdx55-telit-fn980-tlb.dts   | 45 +++++++------------
>  1 file changed, 15 insertions(+), 30 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
> index a4fa468a095f..ac8b4626ae9a 100644
> --- a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
> +++ b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
> @@ -282,40 +282,25 @@ &remoteproc_mpss {
>  };
>  
>  &tlmm {
> -	pcie_ep_clkreq_default: pcie_ep_clkreq_default {
> -		mux {
> -			pins = "gpio56";
> -			function = "pcie_clkreq";
> -		};
> -		config {
> -			pins = "gpio56";
> -			drive-strength = <2>;
> -			bias-disable;
> -		};
> +	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
> +		pins = "gpio56";
> +		function = "pcie_clkreq";
> +		drive-strength = <2>;
> +		bias-disable;
>  	};
>  
> -	pcie_ep_perst_default: pcie_ep_perst_default {
> -		mux {
> -			pins = "gpio57";
> -			function = "gpio";
> -		};
> -		config {
> -			pins = "gpio57";
> -			drive-strength = <2>;
> -			bias-pull-down;
> -		};
> +	pcie_ep_perst_default: pcie-ep-perst-default-state {
> +		pins = "gpio57";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
>  	};
>  
> -	pcie_ep_wake_default: pcie_ep_wake_default {
> -		mux {
> -			pins = "gpio53";
> -			function = "gpio";
> -		};
> -		config {
> -			pins = "gpio53";
> -			drive-strength = <2>;
> -			bias-disable;
> -		};
> +	pcie_ep_wake_default: pcie-ep-wake-default-state {
> +		pins = "gpio53";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
>  	};
>  };
>  

[PATCH v2 05/33] ARM: dts: qcom: msm8226: align TLMM pin configuration with DT schema

[Krzysztof Kozlowski]

DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts |  6 +++---
 arch/arm/boot/dts/qcom-msm8226.dtsi         | 24 ++++++++++-----------
 2 files changed, 15 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
index 193569f0ca5f..02bef5870526 100644
--- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
@@ -299,8 +299,8 @@ bluetooth_default_state: bluetooth-default-state {
 		input-enable;
 	};
 
-	touch_pins: touch {
-		irq {
+	touch_pins: touch-state {
+		irq-pins {
 			pins = "gpio17";
 			function = "gpio";
 
@@ -309,7 +309,7 @@ irq {
 			input-enable;
 		};
 
-		reset {
+		reset-pins {
 			pins = "gpio16";
 			function = "gpio";
 
diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
index cf2d56929428..3b6e746a4af9 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -354,35 +354,35 @@ tlmm: pinctrl@fd510000 {
 			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 
-			blsp1_i2c1_pins: blsp1-i2c1 {
+			blsp1_i2c1_pins: blsp1-i2c1-state {
 				pins = "gpio2", "gpio3";
 				function = "blsp_i2c1";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c2_pins: blsp1-i2c2 {
+			blsp1_i2c2_pins: blsp1-i2c2-state {
 				pins = "gpio6", "gpio7";
 				function = "blsp_i2c2";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c3_pins: blsp1-i2c3 {
+			blsp1_i2c3_pins: blsp1-i2c3-state {
 				pins = "gpio10", "gpio11";
 				function = "blsp_i2c3";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c4_pins: blsp1-i2c4 {
+			blsp1_i2c4_pins: blsp1-i2c4-state {
 				pins = "gpio14", "gpio15";
 				function = "blsp_i2c4";
 				drive-strength = <2>;
 				bias-disable;
 			};
 
-			blsp1_i2c5_pins: blsp1-i2c5 {
+			blsp1_i2c5_pins: blsp1-i2c5-state {
 				pins = "gpio18", "gpio19";
 				function = "blsp_i2c5";
 				drive-strength = <2>;
@@ -390,13 +390,13 @@ blsp1_i2c5_pins: blsp1-i2c5 {
 			};
 
 			sdhc1_default_state: sdhc1-default-state {
-				clk {
+				clk-pins {
 					pins = "sdc1_clk";
 					drive-strength = <10>;
 					bias-disable;
 				};
 
-				cmd-data {
+				cmd-data-pins {
 					pins = "sdc1_cmd", "sdc1_data";
 					drive-strength = <10>;
 					bias-pull-up;
@@ -404,13 +404,13 @@ cmd-data {
 			};
 
 			sdhc2_default_state: sdhc2-default-state {
-				clk {
+				clk-pins {
 					pins = "sdc2_clk";
 					drive-strength = <10>;
 					bias-disable;
 				};
 
-				cmd-data {
+				cmd-data-pins {
 					pins = "sdc2_cmd", "sdc2_data";
 					drive-strength = <10>;
 					bias-pull-up;
@@ -418,21 +418,21 @@ cmd-data {
 			};
 
 			sdhc3_default_state: sdhc3-default-state {
-				clk {
+				clk-pins {
 					pins = "gpio44";
 					function = "sdc3";
 					drive-strength = <8>;
 					bias-disable;
 				};
 
-				cmd {
+				cmd-pins {
 					pins = "gpio43";
 					function = "sdc3";
 					drive-strength = <8>;
 					bias-pull-up;
 				};
 
-				data {
+				data-pins {
 					pins = "gpio39", "gpio40", "gpio41", "gpio42";
 					function = "sdc3";
 					drive-strength = <8>;
-- 
2.34.1

Re: [PATCH v2 05/33] ARM: dts: qcom: msm8226: align TLMM pin configuration with DT schema

[Konrad Dybcio]

On 26.09.2022 09:43, Krzysztof Kozlowski wrote:
> DT schema expects TLMM pin configuration nodes to be named with
> '-state' suffix and their optional children with '-pins' suffix.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts |  6 +++---
>  arch/arm/boot/dts/qcom-msm8226.dtsi         | 24 ++++++++++-----------
>  2 files changed, 15 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
> index 193569f0ca5f..02bef5870526 100644
> --- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
> +++ b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
> @@ -299,8 +299,8 @@ bluetooth_default_state: bluetooth-default-state {
>  		input-enable;
>  	};
>  
> -	touch_pins: touch {
> -		irq {
> +	touch_pins: touch-state {
> +		irq-pins {
>  			pins = "gpio17";
>  			function = "gpio";
>  
> @@ -309,7 +309,7 @@ irq {
>  			input-enable;
>  		};
>  
> -		reset {
> +		reset-pins {
>  			pins = "gpio16";
>  			function = "gpio";
>  
> diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
> index cf2d56929428..3b6e746a4af9 100644
> --- a/arch/arm/boot/dts/qcom-msm8226.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
> @@ -354,35 +354,35 @@ tlmm: pinctrl@fd510000 {
>  			#interrupt-cells = <2>;
>  			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>  
> -			blsp1_i2c1_pins: blsp1-i2c1 {
> +			blsp1_i2c1_pins: blsp1-i2c1-state {
>  				pins = "gpio2", "gpio3";
>  				function = "blsp_i2c1";
>  				drive-strength = <2>;
>  				bias-disable;
>  			};
>  
> -			blsp1_i2c2_pins: blsp1-i2c2 {
> +			blsp1_i2c2_pins: blsp1-i2c2-state {
>  				pins = "gpio6", "gpio7";
>  				function = "blsp_i2c2";
>  				drive-strength = <2>;
>  				bias-disable;
>  			};
>  
> -			blsp1_i2c3_pins: blsp1-i2c3 {
> +			blsp1_i2c3_pins: blsp1-i2c3-state {
>  				pins = "gpio10", "gpio11";
>  				function = "blsp_i2c3";
>  				drive-strength = <2>;
>  				bias-disable;
>  			};
>  
> -			blsp1_i2c4_pins: blsp1-i2c4 {
> +			blsp1_i2c4_pins: blsp1-i2c4-state {
>  				pins = "gpio14", "gpio15";
>  				function = "blsp_i2c4";
>  				drive-strength = <2>;
>  				bias-disable;
>  			};
>  
> -			blsp1_i2c5_pins: blsp1-i2c5 {
> +			blsp1_i2c5_pins: blsp1-i2c5-state {
>  				pins = "gpio18", "gpio19";
>  				function = "blsp_i2c5";
>  				drive-strength = <2>;
> @@ -390,13 +390,13 @@ blsp1_i2c5_pins: blsp1-i2c5 {
>  			};
>  
>  			sdhc1_default_state: sdhc1-default-state {
> -				clk {
> +				clk-pins {
>  					pins = "sdc1_clk";
>  					drive-strength = <10>;
>  					bias-disable;
>  				};
>  
> -				cmd-data {
> +				cmd-data-pins {
>  					pins = "sdc1_cmd", "sdc1_data";
>  					drive-strength = <10>;
>  					bias-pull-up;
> @@ -404,13 +404,13 @@ cmd-data {
>  			};
>  
>  			sdhc2_default_state: sdhc2-default-state {
> -				clk {
> +				clk-pins {
>  					pins = "sdc2_clk";
>  					drive-strength = <10>;
>  					bias-disable;
>  				};
>  
> -				cmd-data {
> +				cmd-data-pins {
>  					pins = "sdc2_cmd", "sdc2_data";
>  					drive-strength = <10>;
>  					bias-pull-up;
> @@ -418,21 +418,21 @@ cmd-data {
>  			};
>  
>  			sdhc3_default_state: sdhc3-default-state {
> -				clk {
> +				clk-pins {
>  					pins = "gpio44";
>  					function = "sdc3";
>  					drive-strength = <8>;
>  					bias-disable;
>  				};
>  
> -				cmd {
> +				cmd-pins {
>  					pins = "gpio43";
>  					function = "sdc3";
>  					drive-strength = <8>;
>  					bias-pull-up;
>  				};
>  
> -				data {
> +				data-pins {
>  					pins = "gpio39", "gpio40", "gpio41", "gpio42";
>  					function = "sdc3";
>  					drive-strength = <8>;

[PATCH v2 06/33] ARM: dts: qcom: msm8974: align TLMM pin configuration with DT schema

[Krzysztof Kozlowski]

DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 30 +++++++++----------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 6daceaa87802..8138f37233aa 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -573,43 +573,43 @@ bcrmf@1 {
 };
 
 &tlmm {
-	sdc1_on: sdc1-on {
-		clk {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
 			pins = "sdc1_clk";
 			drive-strength = <16>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc1_cmd", "sdc1_data";
 			drive-strength = <10>;
 			bias-pull-up;
 		};
 	};
 
-	sdc2_on: sdc2-on {
-		clk {
+	sdc2_on: sdc2-on-state {
+		clk-pins {
 			pins = "sdc2_clk";
 			drive-strength = <6>;
 			bias-disable;
 		};
 
-		cmd-data {
+		cmd-data-pins {
 			pins = "sdc2_cmd", "sdc2_data";
 			drive-strength = <6>;
 			bias-pull-up;
 		};
 	};
 
-	mpu6515_pin: mpu6515 {
+	mpu6515_pin: mpu6515-state {
 		pins = "gpio73";
 		function = "gpio";
 		bias-disable;
 		input-enable;
 	};
 
-	touch_pin: touch {
-		int {
+	touch_pin: touch-state {
+		int-pins {
 			pins = "gpio5";
 			function = "gpio";
 
@@ -618,7 +618,7 @@ int {
 			input-enable;
 		};
 
-		reset {
+		reset-pins {
 			pins = "gpio8";
 			function = "gpio";
 
@@ -627,25 +627,25 @@ reset {
 		};
 	};
 
-	panel_pin: panel {
+	panel_pin: panel-state {
 		pins = "gpio12";
 		function = "mdp_vsync";
 		drive-strength = <2>;
 		bias-disable;
 	};
 
-	bt_pin: bt {
-		hostwake {
+	bt_pin: bt-state {
+		hostwake-pins {
 			pins = "gpio42";
 			function = "gpio";
 		};
 
-		devwake {
+		devwake-pins {
 			pins = "gpio62";
 			function = "gpio";
 		};
 
-		shutdown {
+		shutdown-pins {
 			pins = "gpio41";
 			function = "gpio";
 		};
-- 
2.34.1

Re: [PATCH v2 06/33] ARM: dts: qcom: msm8974: align TLMM pin configuration with DT schema

[Konrad Dybcio]

On 26.09.2022 09:43, Krzysztof Kozlowski wrote:
> DT schema expects TLMM pin configuration nodes to be named with
> '-state' suffix and their optional children with '-pins' suffix.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 30 +++++++++----------
>  1 file changed, 15 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
> index 6daceaa87802..8138f37233aa 100644
> --- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
> +++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
> @@ -573,43 +573,43 @@ bcrmf@1 {
>  };
>  
>  &tlmm {
> -	sdc1_on: sdc1-on {
> -		clk {
> +	sdc1_on: sdc1-on-state {
> +		clk-pins {
>  			pins = "sdc1_clk";
>  			drive-strength = <16>;
>  			bias-disable;
>  		};
>  
> -		cmd-data {
> +		cmd-data-pins {
>  			pins = "sdc1_cmd", "sdc1_data";
>  			drive-strength = <10>;
>  			bias-pull-up;
>  		};
>  	};
>  
> -	sdc2_on: sdc2-on {
> -		clk {
> +	sdc2_on: sdc2-on-state {
> +		clk-pins {
>  			pins = "sdc2_clk";
>  			drive-strength = <6>;
>  			bias-disable;
>  		};
>  
> -		cmd-data {
> +		cmd-data-pins {
>  			pins = "sdc2_cmd", "sdc2_data";
>  			drive-strength = <6>;
>  			bias-pull-up;
>  		};
>  	};
>  
> -	mpu6515_pin: mpu6515 {
> +	mpu6515_pin: mpu6515-state {
>  		pins = "gpio73";
>  		function = "gpio";
>  		bias-disable;
>  		input-enable;
>  	};
>  
> -	touch_pin: touch {
> -		int {
> +	touch_pin: touch-state {
> +		int-pins {
>  			pins = "gpio5";
>  			function = "gpio";
>  
> @@ -618,7 +618,7 @@ int {
>  			input-enable;
>  		};
>  
> -		reset {
> +		reset-pins {
>  			pins = "gpio8";
>  			function = "gpio";
>  
> @@ -627,25 +627,25 @@ reset {
>  		};
>  	};
>  
> -	panel_pin: panel {
> +	panel_pin: panel-state {
>  		pins = "gpio12";
>  		function = "mdp_vsync";
>  		drive-strength = <2>;
>  		bias-disable;
>  	};
>  
> -	bt_pin: bt {
> -		hostwake {
> +	bt_pin: bt-state {
> +		hostwake-pins {
>  			pins = "gpio42";
>  			function = "gpio";
>  		};
>  
> -		devwake {
> +		devwake-pins {
>  			pins = "gpio62";
>  			function = "gpio";
>  		};
>  
> -		shutdown {
> +		shutdown-pins {
>  			pins = "gpio41";
>  			function = "gpio";
>  		};

[PATCH v2 07/33] dt-bindings: pinctrl: qcom,tlmm-common: add common check for function

[Krzysztof Kozlowski]

Certain pins, like SDcard related, do not have functions and such should
not be required.  Add a check for this in common Qualcomm TLMM pin
controller schema.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,tlmm-common.yaml    | 20 +++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml
index c88c8dcb69d9..e1354f0c64f8 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml
@@ -65,10 +65,6 @@ additionalProperties: true
 
 $defs:
   qcom-tlmm-state:
-    allOf:
-      - $ref: pincfg-node.yaml#
-      - $ref: pinmux-node.yaml#
-
     properties:
       drive-strength:
         enum: [2, 4, 6, 8, 10, 12, 14, 16]
@@ -82,5 +78,21 @@ $defs:
       output-high: true
       output-low: true
 
+    allOf:
+      - $ref: pincfg-node.yaml#
+      - $ref: pinmux-node.yaml#
+
+      - if:
+          properties:
+            pins:
+              items:
+                pattern: "^gpio"
+        then:
+          required:
+            - function
+        else:
+          properties:
+            function: false
+
     additionalProperties: true
 ...
-- 
2.34.1

[PATCH v2 08/33] dt-bindings: pinctrl: qcom,ipq6018: add qpic_pad function

[Krzysztof Kozlowski]

The IPQ6018 pinctrl driver supports qpic_pad and DTS already uses it:

  'qpic_pad' is not one of ['adsp_ext', 'alsp_int', 'atest_bbrx0', ...

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml   | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
index 9c6e2cb0c6a5..0bd1aded132d 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -92,9 +92,9 @@ patternProperties:
                 qdss_ctitrig_in_b0, qdss_ctitrig_in_b1, qdss_ctitrig_out_a0,
                 qdss_ctitrig_out_a1, qdss_ctitrig_out_b0, qdss_ctitrig_out_b1,
                 qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b,
-                qdss_tracedata_a, qdss_tracedata_b, reset_n, sd_card, sd_write,
-                sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3,
-                uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
+                qdss_tracedata_a, qdss_tracedata_b, qpic_pad, reset_n, sd_card,
+                sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2,
+                uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ]
 
       drive-strength:
         enum: [2, 4, 6, 8, 10, 12, 14, 16]
-- 
2.34.1

[PATCH v2 09/33] dt-bindings: pinctrl: qcom,ipq6018: increase number of pins in pinmux

[Krzysztof Kozlowski]

One pinxmux node can have more than 4 pins to configure:

  ['gpio1', 'gpio3', 'gpio4', 'gpio5', 'gpio6', 'gpio7', 'gpio8', 'gpio10', 'gpio11', 'gpio12', 'gpio13', 'gpio14', 'gpio15', 'gpio17'] is too long

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml       | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
index 0bd1aded132d..670eb7162e1a 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -63,7 +63,7 @@ patternProperties:
                       sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2,
                       qdsd_data3 ]
         minItems: 1
-        maxItems: 4
+        maxItems: 16
 
       function:
         description:
-- 
2.34.1

[PATCH v2 10/33] dt-bindings: pinctrl: qcom,ipq6018: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,ipq6018-pinctrl.yaml    | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
index 670eb7162e1a..50d8b04bb590 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -42,10 +42,17 @@ properties:
   gpio-ranges:
     maxItems: 1
 
-#PIN CONFIGURATION NODES
 patternProperties:
-  '-pinmux$':
-    type: object
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-ipq6018-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-ipq6018-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-ipq6018-tlmm-state:
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
       Client device subnodes use below standard properties.
@@ -146,7 +153,7 @@ examples:
               #gpio-cells = <2>;
               gpio-ranges = <&tlmm 0 0 80>;
 
-              serial3-pinmux {
+              serial3-state {
                       pins = "gpio44", "gpio45";
                       function = "blsp2_uart";
                       drive-strength = <8>;
-- 
2.34.1

[PATCH v2 11/33] dt-bindings: pinctrl: qcom,ipq6018: use common TLMM schema

[Krzysztof Kozlowski]

Reference common Qualcomm TLMM pin controller schema, to bring other
regular schemas and additional checks, like function required only for
GPIOs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml    | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
index 50d8b04bb590..111eb5b60e8a 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -56,7 +56,7 @@ $defs:
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
       Client device subnodes use below standard properties.
-    $ref: "/schemas/pinctrl/pincfg-node.yaml"
+    $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
 
     properties:
       pins:
@@ -121,12 +121,11 @@ $defs:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
 allOf:
-  - $ref: "pinctrl.yaml#"
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
 
 required:
   - compatible
-- 
2.34.1

[PATCH v2 12/33] dt-bindings: pinctrl: qcom,ipq6018: fix indentation in example

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../pinctrl/qcom,ipq6018-pinctrl.yaml         | 34 +++++++++----------
 1 file changed, 17 insertions(+), 17 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
index 111eb5b60e8a..fc00158069b0 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml
@@ -141,21 +141,21 @@ additionalProperties: false
 
 examples:
   - |
-        #include <dt-bindings/interrupt-controller/arm-gic.h>
-        tlmm: pinctrl@1000000 {
-              compatible = "qcom,ipq6018-pinctrl";
-              reg = <0x01000000 0x300000>;
-              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-              interrupt-controller;
-              #interrupt-cells = <2>;
-              gpio-controller;
-              #gpio-cells = <2>;
-              gpio-ranges = <&tlmm 0 0 80>;
-
-              serial3-state {
-                      pins = "gpio44", "gpio45";
-                      function = "blsp2_uart";
-                      drive-strength = <8>;
-                      bias-pull-down;
-              };
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@1000000 {
+        compatible = "qcom,ipq6018-pinctrl";
+        reg = <0x01000000 0x300000>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 80>;
+
+        serial3-state {
+            pins = "gpio44", "gpio45";
+            function = "blsp2_uart";
+            drive-strength = <8>;
+            bias-pull-down;
         };
+    };
-- 
2.34.1

[PATCH v2 13/33] dt-bindings: pinctrl: qcom,msm8226: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,msm8226-pinctrl.yaml     | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
index ab4a2b4cfda2..ecb90c77f666 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
@@ -45,9 +45,17 @@ properties:
   gpio-reserved-ranges:
     maxItems: 1
 
-#PIN CONFIGURATION NODES
 patternProperties:
-  '-pins$':
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-msm8226-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-msm8226-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-msm8226-tlmm-state:
     type: object
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
@@ -126,7 +134,7 @@ examples:
                 #interrupt-cells = <2>;
                 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 
-                serial-pins {
+                serial-state {
                         pins = "gpio8", "gpio9";
                         function = "blsp_uart3";
                         drive-strength = <8>;
-- 
2.34.1

[PATCH v2 14/33] dt-bindings: pinctrl: qcom,msm8226: use common TLMM schema

[Krzysztof Kozlowski]

Reference common Qualcomm TLMM pin controller schema, to bring other
regular schemas and additional checks, like function required only for
GPIOs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml    | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
index ecb90c77f666..4420bb23c9dc 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
@@ -60,7 +60,7 @@ $defs:
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
       Client device subnodes use below standard properties.
-    $ref: "/schemas/pinctrl/pincfg-node.yaml"
+    $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
 
     properties:
       pins:
@@ -101,12 +101,11 @@ $defs:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
 allOf:
-  - $ref: "pinctrl.yaml#"
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
 
 required:
   - compatible
-- 
2.34.1

[PATCH v2 15/33] dt-bindings: pinctrl: qcom,msm8226: add functions and input-enable

[Krzysztof Kozlowski]

The MSM8226 pinctrl driver supports input-enable, blsp_i2c4, blsp_uart4
and sdc3 functions and DTS already uses it:

  qcom-msm8226-samsung-s3ve3g.dtb: pinctrl@fd510000: 'blsp1-i2c1', 'blsp1-i2c2', 'blsp1-i2c3', 'blsp1-i2c4', 'blsp1-i2c5' ...
  qcom-apq8026-lg-lenok.dtb: pinctrl@fd510000: touch-state: 'oneOf' conditional failed, one must be fixed:
    'input-enable' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,msm8226-pinctrl.yaml         | 10 ++++------
 1 file changed, 4 insertions(+), 6 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
index 4420bb23c9dc..8c5c85807882 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
@@ -79,9 +79,10 @@ $defs:
           Specify the alternative function to be configured for the specified
           pins. Functions are only valid for gpio pins.
         enum: [ gpio, cci_i2c0, blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim5,
-                blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c5, blsp_spi1,
+                blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_spi1,
                 blsp_spi2, blsp_spi3, blsp_spi5, blsp_uart1, blsp_uart2,
-                blsp_uart3, blsp_uart5, cam_mclk0, cam_mclk1, wlan ]
+                blsp_uart3, blsp_uart4, blsp_uart5, cam_mclk0, cam_mclk1, sdc3,
+                wlan ]
 
       drive-strength:
         enum: [2, 4, 6, 8, 10, 12, 14, 16]
@@ -90,13 +91,10 @@ $defs:
           Selects the drive strength for the specified pins, in mA.
 
       bias-pull-down: true
-
       bias-pull-up: true
-
       bias-disable: true
-
+      input-enable: true
       output-high: true
-
       output-low: true
 
     required:
-- 
2.34.1

[PATCH v2 16/33] dt-bindings: pinctrl: qcom,msm8226: fix indentation in example

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../pinctrl/qcom,msm8226-pinctrl.yaml         | 36 +++++++++----------
 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
index 8c5c85807882..b466d2ffc437 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml
@@ -119,22 +119,22 @@ additionalProperties: false
 
 examples:
   - |
-        #include <dt-bindings/interrupt-controller/arm-gic.h>
-        msmgpio: pinctrl@fd510000 {
-                compatible = "qcom,msm8226-pinctrl";
-                reg = <0xfd510000 0x4000>;
-
-                gpio-controller;
-                #gpio-cells = <2>;
-                gpio-ranges = <&msmgpio 0 0 117>;
-                interrupt-controller;
-                #interrupt-cells = <2>;
-                interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-
-                serial-state {
-                        pins = "gpio8", "gpio9";
-                        function = "blsp_uart3";
-                        drive-strength = <8>;
-                        bias-disable;
-                };
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    msmgpio: pinctrl@fd510000 {
+        compatible = "qcom,msm8226-pinctrl";
+        reg = <0xfd510000 0x4000>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&msmgpio 0 0 117>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+        serial-state {
+            pins = "gpio8", "gpio9";
+            function = "blsp_uart3";
+            drive-strength = <8>;
+            bias-disable;
         };
+    };
-- 
2.34.1

[PATCH v2 17/33] dt-bindings: pinctrl: qcom,msm8909-tlmm: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml     | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
index e03530091478..b1735918fa90 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
@@ -43,8 +43,9 @@ patternProperties:
     oneOf:
       - $ref: "#/$defs/qcom-msm8909-tlmm-state"
       - patternProperties:
-          ".*":
+          "-pins$":
             $ref: "#/$defs/qcom-msm8909-tlmm-state"
+        additionalProperties: false
 
 $defs:
   qcom-msm8909-tlmm-state:
@@ -136,13 +137,13 @@ examples:
                 };
 
                 uart-w-subnodes-state {
-                        rx {
+                        rx-pins {
                                 pins = "gpio4";
                                 function = "blsp_uart1";
                                 bias-pull-up;
                         };
 
-                        tx {
+                        tx-pins {
                                 pins = "gpio5";
                                 function = "blsp_uart1";
                                 bias-disable;
-- 
2.34.1

[PATCH v2 18/33] dt-bindings: pinctrl: qcom,msm8909-tlmm: do not require function on non-GPIOs

[Krzysztof Kozlowski]

Certain pins, like SDcard related, do not have functions and such should
not be required.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml | 1 -
 1 file changed, 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
index b1735918fa90..08e2dd5cbebe 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
@@ -113,7 +113,6 @@ $defs:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
-- 
2.34.1

[PATCH v2 19/33] dt-bindings: pinctrl: qcom,msm8909-tlmm: fix indentation in example

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,msm8909-tlmm.yaml   | 60 +++++++++----------
 1 file changed, 30 insertions(+), 30 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
index 08e2dd5cbebe..9c647e24fa9a 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml
@@ -118,35 +118,35 @@ $defs:
 
 examples:
   - |
-        #include <dt-bindings/interrupt-controller/arm-gic.h>
-
-        pinctrl@1000000 {
-                compatible = "qcom,msm8909-tlmm";
-                reg = <0x1000000 0x300000>;
-                interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-                gpio-controller;
-                #gpio-cells = <2>;
-                gpio-ranges = <&tlmm 0 0 117>;
-                interrupt-controller;
-                #interrupt-cells = <2>;
-
-                gpio-wo-subnode-state {
-                        pins = "gpio1";
-                        function = "gpio";
-                };
-
-                uart-w-subnodes-state {
-                        rx-pins {
-                                pins = "gpio4";
-                                function = "blsp_uart1";
-                                bias-pull-up;
-                        };
-
-                        tx-pins {
-                                pins = "gpio5";
-                                function = "blsp_uart1";
-                                bias-disable;
-                        };
-                };
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    pinctrl@1000000 {
+        compatible = "qcom,msm8909-tlmm";
+        reg = <0x1000000 0x300000>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 117>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+
+        gpio-wo-subnode-state {
+            pins = "gpio1";
+            function = "gpio";
         };
+
+        uart-w-subnodes-state {
+            rx-pins {
+                pins = "gpio4";
+                function = "blsp_uart1";
+                bias-pull-up;
+            };
+
+            tx-pins {
+                pins = "gpio5";
+                function = "blsp_uart1";
+                bias-disable;
+            };
+        };
+    };
 ...
-- 
2.34.1

[PATCH v2 20/33] dt-bindings: pinctrl: qcom,msm8953: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,msm8953-pinctrl.yaml     | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
index d4da558cde54..c162796ab604 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
@@ -44,9 +44,17 @@ properties:
   gpio-ranges:
     maxItems: 1
 
-#PIN CONFIGURATION NODES
 patternProperties:
-  '-pins$':
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-msm8953-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-msm8953-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-msm8953-tlmm-state:
     type: object
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
@@ -163,7 +171,7 @@ examples:
               #gpio-cells = <2>;
               gpio-ranges = <&tlmm 0 0 142>;
 
-              serial_default: serial-pins {
+              serial_default: serial-state {
                     pins = "gpio4", "gpio5";
                     function = "blsp_uart2";
                     drive-strength = <2>;
-- 
2.34.1

[PATCH v2 21/33] dt-bindings: pinctrl: qcom,msm8953: use common TLMM schema

[Krzysztof Kozlowski]

Reference common Qualcomm TLMM pin controller schema, to bring other
regular schemas and additional checks, like function required only for
GPIOs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml    | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
index c162796ab604..c4ab54c9d5e8 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
@@ -59,7 +59,7 @@ $defs:
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
       Client device subnodes use below standard properties.
-    $ref: "/schemas/pinctrl/pincfg-node.yaml"
+    $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
 
     properties:
       pins:
@@ -139,12 +139,11 @@ $defs:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
 allOf:
-  - $ref: "pinctrl.yaml#"
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
 
 required:
   - compatible
-- 
2.34.1

[PATCH v2 22/33] dt-bindings: pinctrl: qcom,msm8953: fix indentation in example

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../pinctrl/qcom,msm8953-pinctrl.yaml         | 34 +++++++++----------
 1 file changed, 17 insertions(+), 17 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
index c4ab54c9d5e8..48676393352e 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
@@ -159,21 +159,21 @@ additionalProperties: false
 
 examples:
   - |
-        #include <dt-bindings/interrupt-controller/arm-gic.h>
-        tlmm: pinctrl@1000000 {
-              compatible = "qcom,msm8953-pinctrl";
-              reg = <0x01000000 0x300000>;
-              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-              interrupt-controller;
-              #interrupt-cells = <2>;
-              gpio-controller;
-              #gpio-cells = <2>;
-              gpio-ranges = <&tlmm 0 0 142>;
-
-              serial_default: serial-state {
-                    pins = "gpio4", "gpio5";
-                    function = "blsp_uart2";
-                    drive-strength = <2>;
-                    bias-disable;
-              };
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@1000000 {
+        compatible = "qcom,msm8953-pinctrl";
+        reg = <0x01000000 0x300000>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 142>;
+
+        serial_default: serial-state {
+            pins = "gpio4", "gpio5";
+            function = "blsp_uart2";
+            drive-strength = <2>;
+            bias-disable;
         };
+    };
-- 
2.34.1

[PATCH v2 23/33] dt-bindings: pinctrl: qcom,mdm9607: do not require function on non-GPIOs

[Krzysztof Kozlowski]

Certain pins, like SDcard related, do not have functions and such should
not be required.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml        | 1 -
 1 file changed, 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
index f7bd4be1739e..57a4fed55de7 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
@@ -115,7 +115,6 @@ patternProperties:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
-- 
2.34.1

[PATCH v2 24/33] dt-bindings: pinctrl: qcom,mdm9607: fix indentation in example

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../pinctrl/qcom,mdm9607-pinctrl.yaml         | 22 +++++++++----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
index 57a4fed55de7..a37b358715a3 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-pinctrl.yaml
@@ -120,14 +120,14 @@ patternProperties:
 
 examples:
   - |
-        #include <dt-bindings/interrupt-controller/arm-gic.h>
-        tlmm: pinctrl@1000000 {
-          compatible = "qcom,mdm9607-tlmm";
-          reg = <0x01000000 0x300000>;
-          interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-          gpio-controller;
-          gpio-ranges = <&msmgpio 0 0 80>;
-          #gpio-cells = <2>;
-          interrupt-controller;
-          #interrupt-cells = <2>;
-        };
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@1000000 {
+        compatible = "qcom,mdm9607-tlmm";
+        reg = <0x01000000 0x300000>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+        gpio-controller;
+        gpio-ranges = <&msmgpio 0 0 80>;
+        #gpio-cells = <2>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+    };
-- 
2.34.1

[PATCH v2 25/33] dt-bindings: pinctrl: qcom,qcm2290: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,qcm2290-pinctrl.yaml           | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml
index 3f4f1c0360b5..5324b61eb4f7 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml
@@ -50,8 +50,9 @@ patternProperties:
     oneOf:
       - $ref: "#/$defs/qcom-qcm2290-tlmm-state"
       - patternProperties:
-          ".*":
+          "-pins$":
             $ref: "#/$defs/qcom-qcm2290-tlmm-state"
+        additionalProperties: false
 
 '$defs':
   qcom-qcm2290-tlmm-state:
@@ -146,19 +147,19 @@ examples:
         gpio-ranges = <&tlmm 0 0 127>;
 
         sdc2_on_state: sdc2-on-state {
-            clk {
+            clk-pins {
                 pins = "sdc2_clk";
                 bias-disable;
                 drive-strength = <16>;
             };
 
-            cmd {
+            cmd-pins {
                 pins = "sdc2_cmd";
                 bias-pull-up;
                 drive-strength = <10>;
             };
 
-            data {
+            data-pins {
                 pins = "sdc2_data";
                 bias-pull-up;
                 drive-strength = <10>;
-- 
2.34.1

[PATCH v2 26/33] dt-bindings: pinctrl: qcom,qcm2290: use common TLMM schema

[Krzysztof Kozlowski]

Reference common Qualcomm TLMM pin controller schema, to bring other
regular schemas and additional checks, like function required only for
GPIOs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml       | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml
index 5324b61eb4f7..2a23f413c8c2 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-pinctrl.yaml
@@ -119,7 +119,7 @@ patternProperties:
     additionalProperties: false
 
 allOf:
-  - $ref: "pinctrl.yaml#"
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
 
 required:
   - compatible
-- 
2.34.1

[PATCH v2 27/33] dt-bindings: pinctrl: qcom,sdx55: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.

  qcom-sdx55-telit-fn980-tlb.dtb: pinctrl@f100000: 'pcie_ep_clkreq_default', 'pcie_ep_perst_default', 'pcie_ep_wake_default' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'

This method also unifies the bindings with other Qualcomm TLMM and LPASS
pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,sdx55-pinctrl.yaml       | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
index a38090b14aab..fff57abf4fbc 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
@@ -45,9 +45,17 @@ properties:
   gpio-reserved-ranges:
     maxItems: 1
 
-#PIN CONFIGURATION NODES
 patternProperties:
-  '-pins$':
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-sdx55-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-sdx55-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-sdx55-tlmm-state:
     type: object
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
@@ -146,7 +154,7 @@ examples:
                 #interrupt-cells = <2>;
                 interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
 
-                serial-pins {
+                serial-state {
                         pins = "gpio8", "gpio9";
                         function = "blsp_uart3";
                         drive-strength = <8>;
-- 
2.34.1

[PATCH v2 28/33] dt-bindings: pinctrl: qcom,sdx55: use common TLMM schema

[Krzysztof Kozlowski]

Reference common Qualcomm TLMM pin controller schema, to bring other
regular schemas and additional checks, like function required only for
GPIOs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml      | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
index fff57abf4fbc..52b7a557f452 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
@@ -60,7 +60,7 @@ $defs:
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
       Client device subnodes use below standard properties.
-    $ref: "/schemas/pinctrl/pincfg-node.yaml"
+    $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
 
     properties:
       pins:
@@ -122,12 +122,11 @@ $defs:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
 allOf:
-  - $ref: "pinctrl.yaml#"
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
 
 required:
   - compatible
-- 
2.34.1

[PATCH v2 29/33] dt-bindings: pinctrl: qcom,sdx55: fix indentation in example

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,sdx55-pinctrl.yaml  | 34 +++++++++----------
 1 file changed, 17 insertions(+), 17 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
index 52b7a557f452..b861feab73dd 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml
@@ -142,23 +142,23 @@ additionalProperties: false
 
 examples:
   - |
-        #include <dt-bindings/interrupt-controller/arm-gic.h>
-        tlmm: pinctrl@1f00000 {
-                compatible = "qcom,sdx55-pinctrl";
-                reg = <0x0f100000 0x300000>;
-                gpio-controller;
-                #gpio-cells = <2>;
-                gpio-ranges = <&tlmm 0 0 108>;
-                interrupt-controller;
-                #interrupt-cells = <2>;
-                interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
-
-                serial-state {
-                        pins = "gpio8", "gpio9";
-                        function = "blsp_uart3";
-                        drive-strength = <8>;
-                        bias-disable;
-                };
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@1f00000 {
+        compatible = "qcom,sdx55-pinctrl";
+        reg = <0x0f100000 0x300000>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 108>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+
+        serial-state {
+            pins = "gpio8", "gpio9";
+            function = "blsp_uart3";
+            drive-strength = <8>;
+            bias-disable;
         };
+    };
 
 ...
-- 
2.34.1

[PATCH v2 30/33] dt-bindings: pinctrl: qcom,sdx65: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml   | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml
index cdfcf29dffee..0f796f1f0104 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml
@@ -49,8 +49,10 @@ patternProperties:
     oneOf:
       - $ref: "#/$defs/qcom-sdx65-tlmm-state"
       - patternProperties:
-          ".*":
+          "-pins$":
             $ref: "#/$defs/qcom-sdx65-tlmm-state"
+        additionalProperties: false
+
 '$defs':
   qcom-sdx65-tlmm-state:
     type: object
@@ -175,13 +177,13 @@ examples:
         };
 
         uart-w-subnodes-state {
-            rx {
+            rx-pins {
                 pins = "gpio4";
                 function = "blsp_uart1";
                 bias-pull-up;
             };
 
-            tx {
+            tx-pins {
                 pins = "gpio5";
                 function = "blsp_uart1";
                 bias-disable;
-- 
2.34.1

[PATCH v2 31/33] dt-bindings: pinctrl: qcom,sdx65: use common TLMM schema

[Krzysztof Kozlowski]

Reference common Qualcomm TLMM pin controller schema, to bring other
regular schemas and additional checks, like function required only for
GPIOs.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml       | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml
index 0f796f1f0104..f5451b1a3a2f 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-pinctrl.yaml
@@ -142,10 +142,12 @@ patternProperties:
 
     required:
       - pins
-      - function
 
     additionalProperties: false
 
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
 required:
   - compatible
   - reg
-- 
2.34.1

[PATCH v2 32/33] dt-bindings: pinctrl: qcom,sc7280: fix matching pin config

[Krzysztof Kozlowski]

The TLMM pin controller follows generic pin-controller bindings, so
should have subnodes with '-state' and '-pins'.  Otherwise the subnodes
(level one and two) are not properly matched.  This method also unifies
the bindings with other Qualcomm TLMM and LPASS pinctrl bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,sc7280-pinctrl.yaml      | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml
index ad3496784678..4606ca980dc4 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml
@@ -47,9 +47,17 @@ properties:
 
   wakeup-parent: true
 
-#PIN CONFIGURATION NODES
 patternProperties:
-  '-pins$':
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-sc7280-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-sc7280-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-sc7280-tlmm-state:
     type: object
     description:
       Pinctrl node's client devices use subnodes for desired pin configuration.
@@ -162,7 +170,7 @@ examples:
         gpio-ranges = <&tlmm 0 0 175>;
         wakeup-parent = <&pdc>;
 
-        qup_uart5_default: qup-uart5-pins {
+        qup_uart5_default: qup-uart5-state {
             pins = "gpio46", "gpio47";
             function = "qup13";
             drive-strength = <2>;
-- 
2.34.1

[PATCH v2 33/33] dt-bindings: pinctrl: qcom,sc8280xp: fix indentation in example (remaining piece)

[Krzysztof Kozlowski]

Bindings example should be indented with 4-spaces.  Previous adjustment
missefd one spot.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml    | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
index b9ab130cd558..0b251caaebf2 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-pinctrl.yaml
@@ -139,8 +139,8 @@ examples:
         gpio-ranges = <&tlmm 0 0 230>;
 
         gpio-wo-subnode-state {
-                pins = "gpio1";
-                function = "gpio";
+            pins = "gpio1";
+            function = "gpio";
         };
 
         uart-w-subnodes-state {
-- 
2.34.1

Re: [PATCH v2 00/33] pinctrl/arm64: qcom: continued - fix Qualcomm TLMM pinctrl schema warnings

[Bjorn Andersson]

On Mon, Sep 26, 2022 at 09:43:42AM +0200, Krzysztof Kozlowski wrote:
> Hi,
> 
> Changes since v1
> ================
> v1: https://lore.kernel.org/linux-devicetree/20220924080459.13084-1-krzysztof.kozlowski@linaro.org/T/#t
> 1. As Stephan suggested, move check for function on non-GPIO pins to common
>    TLMM schema.  This affects few commits in the set named:
>    "use common TLMM schema"
>    "do not require function on non-GPIOs"
> 
> Overview
> ========
> This is the third, independent patchset around Qualcomm pinctrl in recent days:
> 1. First round of TLMM fixes: merged
> 2. LPASS fixes:
>    https://lore.kernel.org/linux-devicetree/20220922195651.345369-1-krzysztof.kozlowski@linaro.org/T/#t
> 3. ARMv7 TLMM fixes: *THIS PATCHSET*
> 4. ARMv8 remaining TLMM fixes: v1 send:
>    https://lore.kernel.org/linux-devicetree/20220925110608.145728-1-krzysztof.kozlowski@linaro.org/T/#t
> 
> Dependencies
> ============
> 1. No dependencies.
> 2. dt-bindings are independent of DTS patches.
> 
> Best regards,
> Krzysztof

Reviewed-by: Bjorn Andersson <andersson@kernel.org>

Regards,
Bjorn

> 
> Krzysztof Kozlowski (33):
>   arm64: dts: qcom: ipq6018-cp01-c1: correct blspi1 pins
>   arm64: dts: qcom: ipq6018: align TLMM pin configuration with DT schema
>   ARM: dts: qcom: sdx55: add gpio-ranges to TLMM pinctrl
>   ARM: dts: qcom: sdx55: align TLMM pin configuration with DT schema
>   ARM: dts: qcom: msm8226: align TLMM pin configuration with DT schema
>   ARM: dts: qcom: msm8974: align TLMM pin configuration with DT schema
>   dt-bindings: pinctrl: qcom,tlmm-common: add common check for function
>   dt-bindings: pinctrl: qcom,ipq6018: add qpic_pad function
>   dt-bindings: pinctrl: qcom,ipq6018: increase number of pins in pinmux
>   dt-bindings: pinctrl: qcom,ipq6018: fix matching pin config
>   dt-bindings: pinctrl: qcom,ipq6018: use common TLMM schema
>   dt-bindings: pinctrl: qcom,ipq6018: fix indentation in example
>   dt-bindings: pinctrl: qcom,msm8226: fix matching pin config
>   dt-bindings: pinctrl: qcom,msm8226: use common TLMM schema
>   dt-bindings: pinctrl: qcom,msm8226: add functions and input-enable
>   dt-bindings: pinctrl: qcom,msm8226: fix indentation in example
>   dt-bindings: pinctrl: qcom,msm8909-tlmm: fix matching pin config
>   dt-bindings: pinctrl: qcom,msm8909-tlmm: do not require function on
>     non-GPIOs
>   dt-bindings: pinctrl: qcom,msm8909-tlmm: fix indentation in example
>   dt-bindings: pinctrl: qcom,msm8953: fix matching pin config
>   dt-bindings: pinctrl: qcom,msm8953: use common TLMM schema
>   dt-bindings: pinctrl: qcom,msm8953: fix indentation in example
>   dt-bindings: pinctrl: qcom,mdm9607: do not require function on
>     non-GPIOs
>   dt-bindings: pinctrl: qcom,mdm9607: fix indentation in example
>   dt-bindings: pinctrl: qcom,qcm2290: fix matching pin config
>   dt-bindings: pinctrl: qcom,qcm2290: use common TLMM schema
>   dt-bindings: pinctrl: qcom,sdx55: fix matching pin config
>   dt-bindings: pinctrl: qcom,sdx55: use common TLMM schema
>   dt-bindings: pinctrl: qcom,sdx55: fix indentation in example
>   dt-bindings: pinctrl: qcom,sdx65: fix matching pin config
>   dt-bindings: pinctrl: qcom,sdx65: use common TLMM schema
>   dt-bindings: pinctrl: qcom,sc7280: fix matching pin config
>   dt-bindings: pinctrl: qcom,sc8280xp: fix indentation in example
>     (remaining piece)
> 
>  .../pinctrl/qcom,ipq6018-pinctrl.yaml         | 60 +++++++++--------
>  .../pinctrl/qcom,mdm9607-pinctrl.yaml         | 23 ++++---
>  .../pinctrl/qcom,msm8226-pinctrl.yaml         | 63 +++++++++---------
>  .../bindings/pinctrl/qcom,msm8909-tlmm.yaml   | 64 +++++++++----------
>  .../pinctrl/qcom,msm8953-pinctrl.yaml         | 51 ++++++++-------
>  .../pinctrl/qcom,qcm2290-pinctrl.yaml         | 11 ++--
>  .../bindings/pinctrl/qcom,sc7280-pinctrl.yaml | 14 +++-
>  .../pinctrl/qcom,sc8280xp-pinctrl.yaml        |  4 +-
>  .../bindings/pinctrl/qcom,sdx55-pinctrl.yaml  | 51 ++++++++-------
>  .../bindings/pinctrl/qcom,sdx65-pinctrl.yaml  | 12 ++--
>  .../bindings/pinctrl/qcom,tlmm-common.yaml    | 20 ++++--
>  arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts   |  6 +-
>  arch/arm/boot/dts/qcom-msm8226.dtsi           | 24 +++----
>  .../qcom-msm8974-lge-nexus5-hammerhead.dts    | 30 ++++-----
>  .../boot/dts/qcom-sdx55-telit-fn980-tlb.dts   | 45 +++++--------
>  arch/arm/boot/dts/qcom-sdx55.dtsi             |  1 +
>  arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts  |  8 ++-
>  arch/arm64/boot/dts/qcom/ipq6018.dtsi         |  4 +-
>  18 files changed, 264 insertions(+), 227 deletions(-)
> 
> -- 
> 2.34.1
>