messages from 2020-10-29 16:14:55 to 2020-11-05 01:47:33 UTC [more...]
[PATCH 0/5] tps65910: cleanup regmap use
2020-11-05 1:47 UTC (10+ messages)
` [PATCH 1/5] gpio: tps65910: use regmap accessors
` [PATCH 3/5] mfd: tps65911-comparator: "
` [PATCH 4/5] mfd: tps65910: clean up after switching to regmap
[PATCH 1/4] pinctrl: amd: fix incorrect way to disable debounce filter
2020-11-04 23:09 UTC (9+ messages)
` [PATCH 2/4] pinctrl: amd: use higher precision for 512 RtcClk
` [PATCH 3/4] pinctrl: amd: print debounce filter info in debugfs
` [PATCH 4/4] pinctrl: amd: remove debounce filter setting in irq type setting
[PATCH v2 1/4] pinctrl: amd: fix incorrect way to disable debounce filter
2020-11-04 23:07 UTC (4+ messages)
` [PATCH v2 2/4] pinctrl: amd: use higher precision for 512 RtcClk
` [PATCH v2 3/4] pinctrl: amd: print debounce filter info in debugfs
` [PATCH v2 4/4] pinctrl: amd: remove debounce filter setting in irq type setting
[PATCH 0/2] pinctrl: qcom: Add sm8250 lpass lpi pinctrl support
2020-11-04 22:05 UTC (4+ messages)
` [PATCH 1/2] dt-bindings: pinctrl: qcom: Add sm8250 lpass lpi pinctrl bindings
` [PATCH 2/2] pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver
[PATCH v2 0/8] gpio: exar: refactor the driver
2020-11-04 20:36 UTC (11+ messages)
` [PATCH v2 1/8] regmap: provide regmap_assign_bits()
` [PATCH v2 2/8] gpio: exar: add a newline after the copyright notice
` [PATCH v2 3/8] gpio: exar: include idr.h
` [PATCH v2 4/8] gpio: exar: switch to a simpler IDA interface
` [PATCH v2 5/8] gpio: exar: use a helper variable for &pdev->dev
` [RFT PATCH v2 6/8] gpio: exar: unduplicate address and offset computation
` [RFT PATCH v2 7/8] gpio: exar: switch to using regmap
` [PATCH v2 8/8] gpio: exar: use devm action for freeing the IDA and drop remove()
[PATCH v3 00/11] Raspberry Pi PoE HAT fan support
2020-11-04 19:55 UTC (14+ messages)
` [PATCH v3 01/11] firmware: raspberrypi: Introduce devm_rpi_firmware_get()
` [PATCH v3 02/11] clk: bcm: rpi: Release firmware handle on unbind
` [PATCH v3 03/11] gpio: raspberrypi-exp: "
` [PATCH v3 04/11] reset: raspberrypi: "
` [PATCH v3 05/11] soc: bcm: raspberrypi-power: "
` [PATCH v3 06/11] staging: vchiq: "
` [PATCH v3 07/11] input: raspberrypi-ts: Release firmware handle when not needed
` [PATCH v3 08/11] firmware: raspberrypi: Get rid of rpi_firmware_get()
` [PATCH v3 09/11] dt-bindings: pwm: Add binding for RPi firmware PWM bus
` [PATCH v3 10/11] DO NOT MERGE: ARM: dts: Add RPi's official PoE hat support
` [PATCH v3 11/11] pwm: Add Raspberry Pi Firmware based PWM bus
[PATCH v2 1/2] dt-bindings: pinctrl: qcom: Add SDX55 pinctrl bindings
2020-11-04 18:54 UTC (5+ messages)
` [PATCH v2 2/2] pinctrl: qcom: Add SDX55 pincontrol driver
gpiolib sysfs access when CONFIG_GPIO_CDEV is not set
2020-11-04 17:26 UTC
[PATCH v2 1/2] gpio: tegra: Add lockdep class
2020-11-04 17:04 UTC (2+ messages)
` [PATCH v2 2/2] gpio: tegra: Use raw_spinlock
[PATCH 0/7] gpio: exar: refactor the driver
2020-11-04 16:32 UTC (13+ messages)
` [RFT PATCH 5/7] gpio: exar: unduplicate address and offset computation
` [RFT PATCH 6/7] gpio: exar: switch to using regmap
[PATCH 0/3] gpio: pcie-idio-24: Fix IRQ handling
2020-11-04 15:47 UTC (8+ messages)
` [PATCH 1/3] gpio: pcie-idio-24: Fix irq mask when masking
` [PATCH 2/3] gpio: pcie-idio-24: Fix IRQ Enable Register value
` [PATCH 3/3] gpio: pcie-idio-24: Enable PEX8311 interrupts
[libgpiod][PATCH v3] treewide: rework struct gpiod_line_bulk
2020-11-04 15:45 UTC (2+ messages)
[libgpiod][RFC PATCH] bindings: cxx: demote the line's parent chip reference to a weak_ptr
2020-11-04 15:45 UTC (9+ messages)
[PATCH v1 1/2] gpio: tegra: Add lockdep class
2020-11-04 15:03 UTC (4+ messages)
` [PATCH v1 2/2] gpio: tegra: Use raw_spinlock
[PATCH] gpio: Do not trigger WARN() with sysfs gpio export/unexport
2020-11-04 11:53 UTC
[PATCH 1/4] selftests/gpio: Use TEST_GEN_PROGS_EXTENDED
2020-11-04 10:08 UTC (4+ messages)
` [PATCH 2/4] selftests/gpio: Move include of lib.mk up
` [PATCH 3/4] selftests/gpio: Fix build when source tree is read only
` [PATCH 4/4] selftests/gpio: Add to CLEAN rule rather than overriding
[libgpiod] libgpiod v2.0 API discussion
2020-11-04 7:47 UTC (2+ messages)
[RFC PATCH 1/3] PCI: Add the IDs for Etron EJ168 and EJ188
2020-11-03 22:32 UTC (2+ messages)
[libgpiod] C++ Bindings ABI Compatibility
2020-11-03 21:06 UTC (4+ messages)
[PATCH 30/33] docs: ABI: cleanup several ABI documents
2020-11-03 15:24 UTC (7+ messages)
[PATCH 1/2] dt-bindings: pinctrl: qcom: Add sc7280 pinctrl bindings
2020-11-03 10:39 UTC (4+ messages)
` [PATCH 2/2] pinctrl: qcom: Add sc7280 pinctrl driver
[PATCH v1] pinctrl: intel: Add Intel Elkhart Lake pin controller support
2020-11-03 11:29 UTC (3+ messages)
[PATCH v1] pinctrl: lynxpoint: Unify initcall location in the code
2020-11-03 11:29 UTC (3+ messages)
[PATCH 1/3 v3] x86/platform/geode: Convert net5501 LED to GPIO machine descriptor
2020-11-03 11:03 UTC (6+ messages)
` [PATCH 2/3 v3] x86/platform/geode: Convert geode "
` [PATCH 3/3 v3] x86/platform/geode: Convert alix "
Any other ways to debug GPIO interrupt controller (pinctrl-amd) for broken touchpads of a new laptop model?
2020-11-03 11:00 UTC (22+ messages)
[PATCH v2 0/8] slab: provide and use krealloc_array()
2020-11-03 10:55 UTC (15+ messages)
` [PATCH v2 1/8] mm: slab: provide krealloc_array()
` [PATCH v2 2/8] ALSA: pcm: use krealloc_array()
` [PATCH v2 3/8] vhost: vringh: "
` [PATCH v2 4/8] pinctrl: "
` [PATCH v2 5/8] edac: ghes: "
` [PATCH v2 6/8] drm: atomic: "
` [PATCH v2 7/8] hwtracing: intel: "
` [PATCH v2 8/8] dma-buf: "
[PATCH v2 1/3] gpiolib: acpi: Respect bias settings for GpioInt() resource
2020-11-03 8:35 UTC (5+ messages)
[PATCH v3 0/4] gpiolib: acpi: pin configuration fixes
2020-11-02 19:17 UTC (5+ messages)
` [PATCH v3 1/4] gpiolib: acpi: Respect bias settings for GpioInt() resource
` [PATCH v3 2/4] gpiolib: acpi: Use named item for enum gpiod_flags variable
` [PATCH v3 3/4] gpiolib: acpi: Take into account debounce settings
` [PATCH v3 4/4] gpiolib: acpi: Convert pin_index to be u16
[PATCH v7 0/3] Adding support for Microchip/Microsemi serial GPIO controller
2020-11-02 10:46 UTC (5+ messages)
` [PATCH v7 2/3] pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO
` [RFC PATCH] pinctrl: pinctrl-microchip-sgpio: properties_luton can be static
[PATCH v2 0/3] gpiolib: cdev: allow edge event timestamps to be configured as REALTIME
2020-11-02 8:56 UTC (7+ messages)
[PATCH v5 1/2] pinctrl: qcom: Allow pinctrl-msm code to be loadable as a module
2020-11-02 7:42 UTC (3+ messages)
` [PATCH v5 2/2] firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module
[PATCH v12 0/4] Introduce the for_each_set_clump macro
2020-11-01 20:08 UTC (5+ messages)
` [PATCH v12 4/4] gpio: xilinx: Utilize generic bitmap_get_value and _set_value
[PATCH 0/2] pinctrl: ingenic: Cleanup & add lcd-8bit group
2020-11-01 9:01 UTC (3+ messages)
` [PATCH 1/2] pinctrl: ingenic: Get rid of repetitive data
` [PATCH 2/2] pinctrl: ingenic: Add lcd-8bit group for JZ4770
[PATCH v2 0/5] Allow for qcom-pdc, pinctrl-msm and qcom-scm drivers to be loadable as modules
2020-10-31 0:12 UTC (14+ messages)
` [PATCH v2 5/5] firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module
[PATCH v2 24/39] docs: ABI: don't escape ReST-incompatible chars from obsolete and removed
2020-10-30 23:23 UTC (7+ messages)
` [PATCH v2 31/39] docs: ABI: cleanup several ABI documents
[PATCH 1/2] dt-bindings: pinctrl: qcom: Add SDX55 pinctrl bindings
2020-10-30 19:24 UTC (2+ messages)
[RFC 0/3] add available pwm for bananapi-r64
2020-10-30 18:36 UTC (4+ messages)
` [RFC 3/3] pinctl: mt7622: drop pwm ch7 as mt7622 only has 6 channels
[PATCH 1/2] dt-bindings: Fix entry name for I/O High Voltage property
2020-10-30 18:32 UTC (2+ messages)
[PATCH v2 00/10] Raspberry Pi PoE HAT fan support
2020-10-30 15:37 UTC (3+ messages)
` [PATCH v2 08/10] dt-bindings: pwm: Add binding for RPi firmware PWM bus
[PATCH 0/4] gpio: rcar: Cleanups and improvements
2020-10-30 14:58 UTC (2+ messages)
[PATCH] gpiolib: cdev: add GPIO_V2_LINE_FLAG_EDGE_BOTH and use it in edge_irq_thread()
2020-10-30 14:53 UTC (2+ messages)
Is consumer documentation correct?
2020-10-30 14:36 UTC (8+ messages)
[PATCH v4 1/2] pinctrl: qcom: Allow pinctrl-msm code to be loadable as a module
2020-10-30 7:29 UTC (3+ messages)
` [PATCH v4 2/2] firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module
[PATCH] pinctrl: aspeed: Fix GPI only function problem
2020-10-30 6:02 UTC (5+ messages)
` [PATCH v2] "
[gpio:for-next] BUILD SUCCESS 50afb29ae41368d750cf46bece2b13065b0e9cef
2020-10-30 1:33 UTC
[pinctrl:for-next] BUILD SUCCESS 03dec17c36a7376423bff60edbaf42df5d91af53
2020-10-30 1:26 UTC
[PATCH v2 1/3] Documentation: firmware-guide: gpio-properties: Fix factual mistakes
2020-10-29 19:59 UTC (4+ messages)
` [PATCH v2 2/3] Documentation: firmware-guide: gpio-properties: active_low only for GpioIo()
` [PATCH v2 3/3] Documentation: firmware-guide: gpio-properties: Clarify initial output state
[PATCH v1 1/3] Documentation: firmware-guide: gpio-properties: Fix factual mistakes
2020-10-29 19:11 UTC (14+ messages)
` [PATCH v1 2/3] Documentation: firmware-guide: gpio-properties: active_low only for GpioIo()
[PATCH 0/8] slab: provide and use krealloc_array()
2020-10-27 13:29 UTC (3+ messages)
` [PATCH 4/8] pinctrl: "
linusw/for-next baseline: 119 runs, 2 regressions (v5.10-rc1-11-g50afb29ae413)
2020-10-29 18:27 UTC
[PATCH] gpiolib: acpi: Support GpioInt with active_low polarity
2020-10-29 18:14 UTC (6+ messages)
linusw/for-next build: 7 builds: 0 failed, 7 passed, 11 warnings (v5.10-rc1-11-g50afb29ae413)
2020-10-29 17:42 UTC
[RFC PATCH 0/3] GPIO support on the Etron EJ168/EJ188/EJ198 xHCI controllers
2020-10-29 17:11 UTC (8+ messages)
` [RFC PATCH 2/3] dt-bindings: gpio: Add binding documentation for Etron EJ168/EJ188/EJ198
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).