Linux GPIO subsystem development
 help / color / mirror / Atom feed
 messages from 2026-11-17 14:53:30 to 2026-11-17 22:26:48 UTC [more...]

[PATCH v7 0/6] lx2160a: change the pad muxes through the RCW override
 2026-11-17 22:26 UTC  (14+ messages)
` [PATCH v7 1/6] dt-bindings: pinctrl: add the NXP LX2160A RCW pad mux
` [PATCH v7 2/6] dt-bindings: soc: fsl: layerscape-dcfg: add the LX2160A pad-mux child
` [PATCH v7 3/6] soc: fsl: guts: add the RCW override of the pad muxes
` [PATCH v7 4/6] pinctrl: freescale: add the Layerscape RCW pad-mux driver
` [PATCH v7 5/6] arm64: dts: lx2160a: describe the pad muxes as the DCFG RCW override
` [PATCH v7 6/6] arm64: dts: lx2160a: drop the I2C bus recovery of i2c6 and i2c7

[PATCH 0/5] gpio: fix IRQ handling and probe error paths in five drivers
 2026-11-17 21:22 UTC  (3+ messages)
` [PATCH 4/5] gpio: brcmstb: don't turn platform_get_irq errors into -ENOENT

[PATCH 0/2] gpio: davinci: fix probe-time IRQ setup
 2026-11-17 21:20 UTC  (5+ messages)
` [PATCH 1/2] gpio: davinci: use controller-specific MMIO for BINTEN
` [PATCH 2/2] gpio: davinci: allocate bank IRQ data before installing handlers

[PATCH 0/2] pinctrl: mediatek: Add MT8163 support
 2026-11-17 21:00 UTC  (3+ messages)
` [PATCH 1/2] dt-bindings: pinctrl: mediatek: Add MT8163
` [PATCH 2/2] pinctrl: mediatek: Add support for MT8163 pinctrl

[PATCH v6 0/5] lx2160a: change the pad muxes through the RCW override
 2026-11-17 21:02 UTC  (5+ messages)
` [PATCH v6 4/5] pinctrl: freescale: add the Layerscape RCW pad-mux driver

[PATCH v4 00/16] HID: ft260: add UART and GPIO support, plus I2C fixes
 2026-11-17 20:50 UTC  (20+ messages)
` [PATCH v4 01/16] HID: ft260: add serial driver
` [PATCH v4 02/16] HID: ft260: uart: fix "
` [PATCH v4 03/16] HID: ft260: add GPIO support
` [PATCH v4 04/16] HID: ft260: i2c: reduce driver module loading time
` [PATCH v4 05/16] HID: ft260: fix sysfs store failure notice for big numbers
` [PATCH v4 06/16] HID: ft260: i2c: reduce bus-error message severity
` [PATCH v4 07/16] HID: ft260: uart: enable flow control
` [PATCH v4 08/16] HID: ft260: uart: add modem pins control via ioctl
` [PATCH v4 09/16] HID: ft260: group sysfs attrs per HID interface
` [PATCH v4 10/16] HID: ft260: i2c: fix large write transaction failure
` [PATCH v4 11/16] HID: ft260: workaround for TN_189 errata endpoint STALL after enumeration
` [PATCH v4 12/16] HID: ft260: i2c: abort in-flight transfers with STOP before reset
` [PATCH v4 13/16] HID: ft260: i2c: reject an I2C clock outside the supported range
` [PATCH v4 14/16] HID: ft260: i2c: fix i2c_reset sysfs store return value
` [PATCH v4 15/16] HID: ft260: i2c: recover a bus held by a slave
` [PATCH v4 16/16] HID: ft260: use lock guards

[PATCH v2 0/2] gpio: Add the Siflower SF19A2890 GPIO controller
 2026-11-17 19:49 UTC  (4+ messages)
` [PATCH v2 2/2] gpio: Add Siflower GPIO controller driver

[PATCH v2 0/7] pinctrl: ingenic: Add X2600 support
 2026-11-17 19:09 UTC  (10+ messages)
` [PATCH v2 1/7] pinctrl: ingenic: Swap ID_X1600 and ID_X1830
` [PATCH v2 2/7] pinctrl: ingenic: Fix hardware dual-edge interrupts on X1600
` [PATCH v2 3/7] dt-bindings: pinctrl: ingenic: Add X2600 support
` [PATCH v2 4/7] pinctrl: ingenic: Add X2600 register and GPIO IRQ support
` [PATCH v2 5/7] pinctrl: ingenic: Add X2600 pin groups and functions
` [PATCH v2 6/7] pinctrl: ingenic: Handle X2600 Port E Schmitt trigger
` [PATCH v2 7/7] pinctrl: ingenic: Handle X2600 Port E pull configuration

[REGRESSION] gpio: shared-proxy: open-drain regulators on ODROID-HC4 fail with -EPERM
 2026-11-17 18:15 UTC  (3+ messages)

[PATCH v2 0/7] pinctrl: airoha: add AN7589 support
 2026-11-17 18:03 UTC  (7+ messages)
` [PATCH v2 5/7] dt-bindings: pinctrl: airoha: add AN7589

[PATCH] pinctrl: sunxi: a733: do not switch the mux to read IRQ lines
 2026-11-17 17:22 UTC  (2+ messages)

[PATCH v3 RESEND] pinctrl: sunxi: request the per-bank supply optionally
 2026-11-17 16:17 UTC  (2+ messages)

[PATCH v2 0/5] lx2160a: change the pad muxes through the RCW override
 2026-11-17 14:57 UTC  (6+ messages)
` [PATCH v2 4/5] pinctrl: freescale: add the LX2160A RCW pad-mux driver


This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox