From: Richard Genoud <richard.genoud@gmail.com>
To: Janusz Uzycki <j.uzycki@elproma.com.pl>
Cc: "Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Linus Walleij" <linus.walleij@linaro.org>,
"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
"Alexander Shiyan" <shc_work@mail.ru>,
fabio.estevam@freescale.com, "Fabio Estevam" <festevam@gmail.com>,
"linux-serial@vger.kernel.org" <linux-serial@vger.kernel.org>,
"linux-gpio@vger.kernel.org" <linux-gpio@vger.kernel.org>,
"Alexandre Courbot" <gnurou@gmail.com>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>
Subject: Re: [RFC PATCH v2 3/4] serial: at91: Use helpers for gpio irqs
Date: Tue, 13 Jan 2015 17:08:46 +0100 [thread overview]
Message-ID: <CACQ1gAjS4TG82VzphC5Hd44SekJv8M322x7dvf91m-n-VqN_=A@mail.gmail.com> (raw)
In-Reply-To: <1420900366-9169-3-git-send-email-j.uzycki@elproma.com.pl>
2015-01-10 15:32 GMT+01:00 Janusz Uzycki <j.uzycki@elproma.com.pl>:
> The patch updates atmel_serial driver to use new mctrl_gpio helpers for
> gpio irqs. The code is simpler now.
>
> Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
> ---
>
> The patch exists since v2.
> Compile-test only - please test it on real hardware.
>
> ---
> drivers/tty/serial/atmel_serial.c | 123 +++++++-------------------------------
> 1 file changed, 20 insertions(+), 103 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 4d848a2..a59a892 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -168,7 +168,6 @@ struct atmel_uart_port {
> struct circ_buf rx_ring;
>
> struct mctrl_gpios *gpios;
> - int gpio_irq[UART_GPIO_MAX];
> unsigned int tx_done_mask;
> bool ms_irq_enabled;
> bool is_usart; /* usart or uart */
> @@ -499,24 +498,18 @@ static void atmel_enable_ms(struct uart_port *port)
>
> atmel_port->ms_irq_enabled = true;
>
> - if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0)
> - enable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]);
> - else
> + mctrl_gpio_enable_ms(atmel_port->gpios);
> +
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_CTS))
> ier |= ATMEL_US_CTSIC;
>
> - if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0)
> - enable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]);
> - else
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DSR))
> ier |= ATMEL_US_DSRIC;
>
> - if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0)
> - enable_irq(atmel_port->gpio_irq[UART_GPIO_RI]);
> - else
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_RI))
> ier |= ATMEL_US_RIIC;
>
> - if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0)
> - enable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]);
> - else
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DCD))
> ier |= ATMEL_US_DCDIC;
>
> UART_PUT_IER(port, ier);
> @@ -538,24 +531,18 @@ static void atmel_disable_ms(struct uart_port *port)
>
> atmel_port->ms_irq_enabled = false;
>
> - if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0)
> - disable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]);
> - else
> + mctrl_gpio_disable_ms(atmel_port->gpios);
> +
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_CTS))
> idr |= ATMEL_US_CTSIC;
>
> - if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0)
> - disable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]);
> - else
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DSR))
> idr |= ATMEL_US_DSRIC;
>
> - if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0)
> - disable_irq(atmel_port->gpio_irq[UART_GPIO_RI]);
> - else
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_RI))
> idr |= ATMEL_US_RIIC;
>
> - if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0)
> - disable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]);
> - else
> + if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DCD))
> idr |= ATMEL_US_DCDIC;
>
> UART_PUT_IDR(port, idr);
> @@ -1161,31 +1148,11 @@ atmel_handle_status(struct uart_port *port, unsigned int pending,
> static irqreturn_t atmel_interrupt(int irq, void *dev_id)
> {
> struct uart_port *port = dev_id;
> - struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> unsigned int status, pending, pass_counter = 0;
> - bool gpio_handled = false;
>
> do {
> status = atmel_get_lines_status(port);
> pending = status & UART_GET_IMR(port);
> - if (!gpio_handled) {
> - /*
> - * Dealing with GPIO interrupt
> - */
> - if (irq == atmel_port->gpio_irq[UART_GPIO_CTS])
> - pending |= ATMEL_US_CTSIC;
> -
> - if (irq == atmel_port->gpio_irq[UART_GPIO_DSR])
> - pending |= ATMEL_US_DSRIC;
> -
> - if (irq == atmel_port->gpio_irq[UART_GPIO_RI])
> - pending |= ATMEL_US_RIIC;
> -
> - if (irq == atmel_port->gpio_irq[UART_GPIO_DCD])
> - pending |= ATMEL_US_DCDIC;
> -
> - gpio_handled = true;
> - }
> if (!pending)
> break;
>
> @@ -1665,45 +1632,6 @@ static void atmel_get_ip_name(struct uart_port *port)
> }
> }
>
> -static void atmel_free_gpio_irq(struct uart_port *port)
> -{
> - struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> - enum mctrl_gpio_idx i;
> -
> - for (i = 0; i < UART_GPIO_MAX; i++)
> - if (atmel_port->gpio_irq[i] >= 0)
> - free_irq(atmel_port->gpio_irq[i], port);
> -}
> -
> -static int atmel_request_gpio_irq(struct uart_port *port)
> -{
> - struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> - int *irq = atmel_port->gpio_irq;
> - enum mctrl_gpio_idx i;
> - int err = 0;
> -
> - for (i = 0; (i < UART_GPIO_MAX) && !err; i++) {
> - if (irq[i] < 0)
> - continue;
> -
> - irq_set_status_flags(irq[i], IRQ_NOAUTOEN);
> - err = request_irq(irq[i], atmel_interrupt, IRQ_TYPE_EDGE_BOTH,
> - "atmel_serial", port);
> - if (err)
> - dev_err(port->dev, "atmel_startup - Can't get %d irq\n",
> - irq[i]);
> - }
> -
> - /*
> - * If something went wrong, rollback.
> - */
> - while (err && (--i >= 0))
> - if (irq[i] >= 0)
> - free_irq(irq[i], port);
> -
> - return err;
> -}
> -
> /*
> * Perform initialization and enable port for reception
> */
> @@ -1735,7 +1663,7 @@ static int atmel_startup(struct uart_port *port)
> /*
> * Get the GPIO lines IRQ
> */
> - retval = atmel_request_gpio_irq(port);
> + retval = mctrl_gpio_request_irqs(atmel_port->gpios);
> if (retval)
> goto free_irq;
>
> @@ -1872,7 +1800,7 @@ static void atmel_shutdown(struct uart_port *port)
> * Free the interrupts
> */
> free_irq(port->irq, port);
> - atmel_free_gpio_irq(port);
> + mctrl_gpio_free_irqs(atmel_port->gpios);
>
> atmel_port->ms_irq_enabled = false;
>
> @@ -2501,24 +2429,13 @@ static int atmel_serial_resume(struct platform_device *pdev)
> #define atmel_serial_resume NULL
> #endif
>
> -static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev)
> +static bool atmel_init_gpios(struct atmel_uart_port *p)
> {
> - enum mctrl_gpio_idx i;
> - struct gpio_desc *gpiod;
> -
> - p->gpios = mctrl_gpio_init(dev, 0);
> + p->gpios = mctrl_gpio_init_dt(&p->uart, 0);
> if (IS_ERR_OR_NULL(p->gpios))
> - return -1;
> + return false;
>
> - for (i = 0; i < UART_GPIO_MAX; i++) {
> - gpiod = mctrl_gpio_to_gpiod(p->gpios, i);
> - if (gpiod && (gpiod_get_direction(gpiod) == GPIOF_DIR_IN))
> - p->gpio_irq[i] = gpiod_to_irq(gpiod);
> - else
> - p->gpio_irq[i] = -EINVAL;
> - }
> -
> - return 0;
> + return true;
> }
>
> static int atmel_serial_probe(struct platform_device *pdev)
> @@ -2558,8 +2475,8 @@ static int atmel_serial_probe(struct platform_device *pdev)
> port->backup_imr = 0;
> port->uart.line = ret;
>
> - ret = atmel_init_gpios(port, &pdev->dev);
> - if (ret < 0)
> + port->uart.dev = &pdev->dev;
> + if (!atmel_init_gpios(port))
> dev_err(&pdev->dev, "%s",
> "Failed to initialize GPIOs. The serial port may not work as expected");
>
> --
> 1.7.11.3
>
It's ok, no regression found in atmel-serial.
Tested on an at91sam9g35, full duplex between 2 serial ports at 57600
(one with CTS/RTS handled by the controller, the other with CTS/RTS
handled via GPIO).
Tested-by: Richard Genoud <richard.genoud@gmail.com>
next prev parent reply other threads:[~2015-01-13 16:09 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-10 14:32 [RFC PATCH v2 1/4] tty: serial_mctrl_gpio: Add irqs helpers for input lines Janusz Uzycki
2015-01-10 14:32 ` [RFC PATCH v2 2/4] serial: mxs-auart: Use helpers for gpio irqs Janusz Uzycki
2015-01-13 8:08 ` Uwe Kleine-König
2015-01-13 9:29 ` Janusz Użycki
2015-01-13 9:35 ` Uwe Kleine-König
2015-01-13 9:48 ` Janusz Użycki
2015-01-10 14:32 ` [RFC PATCH v2 3/4] serial: at91: " Janusz Uzycki
2015-01-13 16:08 ` Richard Genoud [this message]
2015-01-14 16:10 ` Nicolas Ferre
2015-01-19 10:14 ` Linus Walleij
2015-01-10 14:32 ` [RFC PATCH v2 4/4] serial: clps711x: Update to new mctrl_gpio_init_dt Janusz Uzycki
2015-01-12 22:25 ` [RFC PATCH v2 1/4] tty: serial_mctrl_gpio: Add irqs helpers for input lines Alexandre Courbot
2015-01-13 8:03 ` Uwe Kleine-König
2015-01-13 9:20 ` Janusz Użycki
2015-01-13 13:04 ` Richard Genoud
2015-01-13 13:52 ` Janusz Użycki
2015-01-13 14:30 ` Richard Genoud
2015-01-13 14:33 ` Janusz Użycki
2015-01-13 14:41 ` Richard Genoud
2015-01-13 14:44 ` Janusz Użycki
2015-01-22 10:33 ` Janusz Użycki
2015-01-22 11:37 ` Fabio Estevam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CACQ1gAjS4TG82VzphC5Hd44SekJv8M322x7dvf91m-n-VqN_=A@mail.gmail.com' \
--to=richard.genoud@gmail.com \
--cc=fabio.estevam@freescale.com \
--cc=festevam@gmail.com \
--cc=gnurou@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=j.uzycki@elproma.com.pl \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=shc_work@mail.ru \
--cc=u.kleine-koenig@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).