[PATCH v3 0/3] TI TPS6594 PMIC support (RTC, pinctrl, regulators)

[PATCH v3 0/3] TI TPS6594 PMIC support (RTC, pinctrl, regulators)

[Esteban Blanc]

TPS6594 is a Power Management IC which provides regulators and others
features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.

This series adds support to TI TPS6594 PMIC and its derivatives.

This should be applied on top of other patch series:
- https://lore.kernel.org/all/20230406075622.8990-1-jpanis@baylibre.com/
  For core MFD driver

The features implemented in this series are:
- RTC (child device)
- Pinmux/GPIO (child device)
- Regulator (child device)

RTC description:
The TPS6594 family has an RTC built-in, except for LP8764.
It provides time and an alarm.

Pinmux/GPIO:
TPS6594 family has 11 GPIOs. Those GPIO can also serve different
functions such as I2C or SPI interface, watchdog disable functions.
The driver provides both pinmuxing for the functions and GPIO capability.

Regulator:
TPS6594/TPS6593: 5 BUCKs and 4LDOs
LP8764: 4 BUCKs and no LDO
Bucks can be used in multipahse mode.

Changes since v1:
https://lore.kernel.org/all/20230224133129.887203-1-eblanc@baylibre.com/
Rtc:
- Removed struct tps6594_rtc.
- Removed some dev_err messages.
- Removed some comments.
- Remove some whitespaces in comments and error messages.
- Check if RTC is running before reading a timestamp in read_rtc.
- Stop RTC at the end of probe to wait for a timestamp to be set.
- Add default MFD_TPS6594 to Kconfig.

Pinctrl:
- Removed #define DEBUG.
- Add default MFD_TPS6594 to Kconfig.
- Fix typo and reword help message of Kconfig.

Regulators:
Further to Mark Brown review:
- File header whole block C++ style.
- Configuring modes not supported: omit all mode operations
- Log the error before notifying.
- Request the interrupts while registering the regulators (then remove
  the lookup function).
Further to Matti review:
- Postponed: devm_regulator_irq_helper() and
  regulator_irq_map_event_simple() can probably be used but code.
  refactoring is not so trivial. This can be done later as an enhancement
  after this patch list is merged.
Buck Multi phase management:
- Multiphase property can take an array when 2 multi phase buck, buck12
  and buck34.
- Configuration multi phase buck34 without multiphase buck12 is not
  supported (when only one multiphase, must be buck12). Not clear from the
  spec but confirmed by TI.
- Supported multiphase conficurations: buck12, buck123, buck1234,
  buck12 + buck34.
- All interrupts are attached to the multiphase buck (ie: for regulator
  buck12, buck1 & buck2 interrupts are registered).

Changes since v2:
https://lore.kernel.org/all/20230328091448.648452-1-eblanc@baylibre.com/
Rtc:
- Add logic to avoid reinitializing a working clock.
- Fix some multiline comments format.

Regulators:
Further to Mark Brown review:
- Log the error before notifying.
- Request the interrupts while registering the regulators.
Further to Krzysztof Kozlowski:
https://lore.kernel.org/all/75f0a18d-aed9-8610-2925-4e604b4b0241@baylibre.com/
- Remove ti, multi-phase-id property which is redundant with buck dts naming
  rules.

Esteban Blanc (2):
  rtc: tps6594: add driver for TPS6594 PMIC RTC
  pinctrl: tps6594: add for TPS6594 PMIC

Jerome Neanne (1):
  regulator: tps6594-regulator: Add driver for TI TPS6594 regulators

 drivers/pinctrl/Kconfig               |  10 +
 drivers/pinctrl/Makefile              |   1 +
 drivers/pinctrl/pinctrl-tps6594.c     | 365 +++++++++++++++
 drivers/regulator/Kconfig             |  13 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/tps6594-regulator.c | 620 ++++++++++++++++++++++++++
 drivers/rtc/Kconfig                   |   9 +
 drivers/rtc/Makefile                  |   1 +
 drivers/rtc/rtc-tps6594.c             | 473 ++++++++++++++++++++
 9 files changed, 1493 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-tps6594.c
 create mode 100644 drivers/regulator/tps6594-regulator.c
 create mode 100644 drivers/rtc/rtc-tps6594.c

-- 
2.39.2

[PATCH v3 1/3] rtc: tps6594: add driver for TPS6594 PMIC RTC

[Esteban Blanc]

TPS6594 PMIC is a MFD driver. This adds support for the RTC found inside
TPS6594 family of PMIC.

Alarm is also supported.

Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 drivers/rtc/Kconfig       |   9 +
 drivers/rtc/Makefile      |   1 +
 drivers/rtc/rtc-tps6594.c | 473 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 483 insertions(+)
 create mode 100644 drivers/rtc/rtc-tps6594.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index 5a71579af0a1..e5614a570d7e 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -578,6 +578,15 @@ config RTC_DRV_TPS6586X
 	  along with alarm. This driver supports the RTC driver for
 	  the TPS6586X RTC module.
 
+config RTC_DRV_TPS6594
+	tristate "TI TPS6594 RTC driver"
+	depends on MFD_TPS6594
+	default MFD_TPS6594
+	help
+	  TI Power Management IC TPS6594 supports RTC functionality
+	  along with alarm. This driver supports the RTC driver for
+	  the TPS6594 RTC module.
+
 config RTC_DRV_TPS65910
 	tristate "TI TPS65910 RTC driver"
 	depends on MFD_TPS65910
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index ea445d1ebb17..3d3f8c9d0697 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -175,6 +175,7 @@ obj-$(CONFIG_RTC_DRV_TEGRA)	+= rtc-tegra.o
 obj-$(CONFIG_RTC_DRV_TEST)	+= rtc-test.o
 obj-$(CONFIG_RTC_DRV_TI_K3)	+= rtc-ti-k3.o
 obj-$(CONFIG_RTC_DRV_TPS6586X)	+= rtc-tps6586x.o
+obj-$(CONFIG_RTC_DRV_TPS6594)	+= rtc-tps6594.o
 obj-$(CONFIG_RTC_DRV_TPS65910)	+= rtc-tps65910.o
 obj-$(CONFIG_RTC_DRV_TWL4030)	+= rtc-twl.o
 obj-$(CONFIG_RTC_DRV_VT8500)	+= rtc-vt8500.o
diff --git a/drivers/rtc/rtc-tps6594.c b/drivers/rtc/rtc-tps6594.c
new file mode 100644
index 000000000000..f430592312e6
--- /dev/null
+++ b/drivers/rtc/rtc-tps6594.c
@@ -0,0 +1,473 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * RTC driver for tps6594 PMIC
+ *
+ * Copyright (C) 2022 BayLibre Incorporated - https://www.baylibre.com/
+ */
+
+#include <linux/bcd.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/rtc.h>
+#include <linux/types.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+
+#include <linux/mfd/tps6594.h>
+
+#define TPS6594_GET_TIME_ON TPS6594_BIT_GET_TIME
+#define TPS6594_GET_TIME_OFF 0
+#define TPS6594_IT_ALARM_ON TPS6594_BIT_IT_ALARM
+#define TPS6594_IT_ALARM_OFF 0
+#define TPS6594_AUTO_COMP_ON TPS6594_BIT_IT_ALARM
+
+/* Total number of RTC registers needed to set time*/
+#define NUM_TIME_REGS (TPS6594_REG_RTC_WEEKS - TPS6594_REG_RTC_SECONDS + 1)
+
+/* Total number of RTC alarm register */
+#define NUM_TIME_ALARM_REGS (NUM_TIME_REGS - 1)
+
+/* Total number of RTC registers needed to set compensation registers */
+#define NUM_COMP_REGS (TPS6594_REG_RTC_COMP_MSB - TPS6594_REG_RTC_COMP_LSB + 1)
+
+/*
+ * Min and max values supported with 'offset' interface (swapped sign)
+ * After conversion, the values does not exceed the range [-32767, 33767] which COMP_REG must
+ * conform to
+ */
+#define MIN_OFFSET (-277774)
+#define MAX_OFFSET (277774)
+
+/* Number of ticks per hour */
+#define TICKS_PER_HOUR (32768 * 3600)
+
+/* Multiplier for ppb conversions */
+#define PPB_MULT (1000000000LL)
+
+static int tps6594_rtc_alarm_irq_enable(struct device *dev,
+					unsigned int enabled)
+{
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	u8 val = 0;
+	int ret;
+
+	val = enabled ? TPS6594_IT_ALARM_ON : TPS6594_IT_ALARM_OFF;
+
+	ret = regmap_update_bits(tps->regmap, TPS6594_REG_RTC_INTERRUPTS,
+				 TPS6594_BIT_IT_ALARM, val);
+
+	return ret;
+}
+
+/* Pulse GET_TIME field of RTC_CTRL_1 to store a timestamp in shadow registers */
+static int tps6594_rtc_shadow_timestamp(struct device *dev, struct tps6594 *tps)
+{
+	int ret;
+
+	/*
+	 * Set GET_TIME to 0. This way, next time we set GET_TIME to 1 we are sure to store an
+	 * up-to-date timestamp
+	 */
+	ret = regmap_clear_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+				TPS6594_BIT_GET_TIME);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Copy content of RTC registers to shadow registers or latches to read a coherent
+	 * timestamp
+	 */
+	return regmap_set_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+			       TPS6594_BIT_GET_TIME);
+}
+
+/*
+ * Gets current tps6594 RTC time and date parameters.
+ *
+ * The RTC's time/alarm representation is not what gmtime(3) requires
+ * Linux to use:
+ *
+ *  - Months are 1..12 vs Linux 0-11
+ *  - Years are 0..99 vs Linux 1900..N (we assume 21st century)
+ */
+static int tps6594_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+	unsigned char rtc_data[NUM_TIME_REGS];
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	int ret;
+
+	/* Check if RTC is running. */
+	ret = regmap_test_bits(tps->regmap, TPS6594_REG_RTC_STATUS,
+			       TPS6594_BIT_RUN);
+	if (ret < 0)
+		return ret;
+	if (ret == 0)
+		return -EINVAL;
+
+	ret = tps6594_rtc_shadow_timestamp(dev, tps);
+	if (ret < 0)
+		return ret;
+
+	/* Read shadowed RTC registers */
+	ret = regmap_bulk_read(tps->regmap, TPS6594_REG_RTC_SECONDS, rtc_data,
+			       NUM_TIME_REGS);
+	if (ret < 0)
+		return ret;
+
+	tm->tm_sec = bcd2bin(rtc_data[0]);
+	tm->tm_min = bcd2bin(rtc_data[1]);
+	tm->tm_hour = bcd2bin(rtc_data[2]);
+	tm->tm_mday = bcd2bin(rtc_data[3]);
+	tm->tm_mon = bcd2bin(rtc_data[4]) - 1;
+	tm->tm_year = bcd2bin(rtc_data[5]) + 100;
+	tm->tm_wday = bcd2bin(rtc_data[6]);
+
+	return ret;
+}
+
+/*
+ * Sets current tps6594 RTC time and date parameters.
+ *
+ * The RTC's time/alarm representation is not what gmtime(3) requires
+ * Linux to use:
+ *
+ *  - Months are 1..12 vs Linux 0-11
+ *  - Years are 0..99 vs Linux 1900..N (we assume 21st century)
+ */
+static int tps6594_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+	unsigned char rtc_data[NUM_TIME_REGS];
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	int ret;
+
+	rtc_data[0] = bin2bcd(tm->tm_sec);
+	rtc_data[1] = bin2bcd(tm->tm_min);
+	rtc_data[2] = bin2bcd(tm->tm_hour);
+	rtc_data[3] = bin2bcd(tm->tm_mday);
+	rtc_data[4] = bin2bcd(tm->tm_mon + 1);
+	rtc_data[5] = bin2bcd(tm->tm_year - 100);
+	rtc_data[6] = bin2bcd(tm->tm_wday);
+
+	/* Stop RTC while updating the RTC time registers */
+	ret = regmap_clear_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+				TPS6594_BIT_STOP_RTC);
+	if (ret < 0)
+		return ret;
+
+	/* Update all the time registers in one shot */
+	ret = regmap_bulk_write(tps->regmap, TPS6594_REG_RTC_SECONDS, rtc_data,
+				NUM_TIME_REGS);
+	if (ret < 0)
+		return ret;
+
+	/* Start back RTC */
+	return regmap_set_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+			       TPS6594_BIT_STOP_RTC);
+}
+
+/*
+ * Gets current tps6594 RTC alarm time.
+ */
+static int tps6594_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm)
+{
+	unsigned char alarm_data[NUM_TIME_ALARM_REGS];
+	u32 int_val;
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	int ret;
+
+	ret = regmap_bulk_read(tps->regmap, TPS6594_REG_ALARM_SECONDS,
+			       alarm_data, NUM_TIME_ALARM_REGS);
+	if (ret < 0)
+		return ret;
+
+	alm->time.tm_sec = bcd2bin(alarm_data[0]);
+	alm->time.tm_min = bcd2bin(alarm_data[1]);
+	alm->time.tm_hour = bcd2bin(alarm_data[2]);
+	alm->time.tm_mday = bcd2bin(alarm_data[3]);
+	alm->time.tm_mon = bcd2bin(alarm_data[4]) - 1;
+	alm->time.tm_year = bcd2bin(alarm_data[5]) + 100;
+
+	ret = regmap_read(tps->regmap, TPS6594_REG_RTC_INTERRUPTS, &int_val);
+	if (ret < 0)
+		return ret;
+
+	alm->enabled = int_val & TPS6594_BIT_IT_ALARM ? 1 : 0;
+
+	return ret;
+}
+
+static int tps6594_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alm)
+{
+	unsigned char alarm_data[NUM_TIME_ALARM_REGS];
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	int ret;
+
+	/* Disable alarm irq before changing the alarm timestamp */
+	ret = tps6594_rtc_alarm_irq_enable(dev, 0);
+	if (ret)
+		return ret;
+
+	alarm_data[0] = bin2bcd(alm->time.tm_sec);
+	alarm_data[1] = bin2bcd(alm->time.tm_min);
+	alarm_data[2] = bin2bcd(alm->time.tm_hour);
+	alarm_data[3] = bin2bcd(alm->time.tm_mday);
+	alarm_data[4] = bin2bcd(alm->time.tm_mon + 1);
+	alarm_data[5] = bin2bcd(alm->time.tm_year - 100);
+
+	/* Update all the alarm registers in one shot */
+	ret = regmap_bulk_write(tps->regmap, TPS6594_REG_ALARM_SECONDS,
+				alarm_data, NUM_TIME_ALARM_REGS);
+	if (ret < 0)
+		return ret;
+
+	if (alm->enabled)
+		ret = tps6594_rtc_alarm_irq_enable(dev, 1);
+
+	return ret;
+}
+
+static int tps6594_rtc_set_calibration(struct device *dev, int calibration)
+{
+	unsigned char comp_data[NUM_COMP_REGS];
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	s16 value;
+	int ret;
+
+	/*
+	 * TPS6594 uses two's complement 16 bit value for compensation for RTC
+	 * crystal inaccuracies. One time every hour when seconds counter
+	 * increments from 0 to 1 compensation value will be added to internal
+	 * RTC counter value.
+	 *
+	 *
+	 * Valid range for compensation value: [-32767 .. 32767]
+	 */
+	if (calibration < -32767 || calibration > 32767) {
+		dev_err(dev, "RTC calibration value out of range: %d\n",
+			calibration);
+		return -EINVAL;
+	}
+
+	value = (s16)calibration;
+
+	comp_data[0] = (u16)value & 0xFF;
+	comp_data[1] = ((u16)value >> 8) & 0xFF;
+
+	/* Update all the compensation registers in one shot */
+	ret = regmap_bulk_write(tps->regmap, TPS6594_REG_RTC_COMP_LSB,
+				comp_data, NUM_COMP_REGS);
+	if (ret < 0)
+		return ret;
+
+	/* Enable automatic compensation */
+	return regmap_set_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+			       TPS6594_BIT_AUTO_COMP);
+}
+
+static int tps6594_rtc_get_calibration(struct device *dev, int *calibration)
+{
+	unsigned char comp_data[NUM_COMP_REGS];
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	unsigned int ctrl;
+	u16 value;
+	int ret;
+
+	ret = regmap_read(tps->regmap, TPS6594_REG_RTC_CTRL_1, &ctrl);
+	if (ret < 0)
+		return ret;
+
+	/* If automatic compensation is not enabled report back zero */
+	if (!(ctrl & TPS6594_BIT_AUTO_COMP)) {
+		*calibration = 0;
+		return 0;
+	}
+
+	ret = regmap_bulk_read(tps->regmap, TPS6594_REG_RTC_COMP_LSB, comp_data,
+			       NUM_COMP_REGS);
+	if (ret < 0)
+		return ret;
+
+	value = (u16)comp_data[0] | ((u16)comp_data[1] << 8);
+
+	*calibration = (s16)value;
+
+	return ret;
+}
+
+static int tps6594_rtc_read_offset(struct device *dev, long *offset)
+{
+	int calibration;
+	s64 tmp;
+	int ret;
+
+	ret = tps6594_rtc_get_calibration(dev, &calibration);
+	if (ret < 0)
+		return ret;
+
+	/* Convert from RTC calibration register format to ppb format */
+	tmp = calibration * (s64)PPB_MULT;
+	if (tmp < 0)
+		tmp -= TICKS_PER_HOUR / 2LL;
+	else
+		tmp += TICKS_PER_HOUR / 2LL;
+	tmp = div_s64(tmp, TICKS_PER_HOUR);
+
+	/*
+	 * Offset value operates in negative way, so swap sign.
+	 * See 8.3.10.5, (32768 - COMP_REG)
+	 */
+	*offset = (long)-tmp;
+
+	return ret;
+}
+
+static int tps6594_rtc_set_offset(struct device *dev, long offset)
+{
+	int calibration;
+	s64 tmp;
+
+	/* Make sure offset value is within supported range */
+	if (offset < MIN_OFFSET || offset > MAX_OFFSET)
+		return -ERANGE;
+
+	/* Convert from ppb format to RTC calibration register format */
+	tmp = offset * (s64)TICKS_PER_HOUR;
+	if (tmp < 0)
+		tmp -= PPB_MULT / 2LL;
+	else
+		tmp += PPB_MULT / 2LL;
+	tmp = div_s64(tmp, PPB_MULT);
+
+	/* Offset value operates in negative way, so swap sign */
+	calibration = (int)-tmp;
+
+	return tps6594_rtc_set_calibration(dev, calibration);
+}
+
+static irqreturn_t tps6594_rtc_interrupt(int irq, void *rtc)
+{
+	struct device *dev = rtc;
+	unsigned long events = 0;
+	struct tps6594 *tps = dev_get_drvdata(dev->parent);
+	struct rtc_device *rtc_dev = dev_get_drvdata(dev);
+	int ret;
+	u32 rtc_reg;
+
+	ret = regmap_read(tps->regmap, TPS6594_REG_RTC_STATUS, &rtc_reg);
+	if (ret)
+		return IRQ_NONE;
+
+	if (rtc_reg & TPS6594_BIT_ALARM)
+		events = RTC_IRQF | RTC_AF;
+
+	/* Notify RTC core on event */
+	rtc_update_irq(rtc_dev, 1, events);
+
+	return IRQ_HANDLED;
+}
+
+static const struct rtc_class_ops tps6594_rtc_ops = {
+	.read_time = tps6594_rtc_read_time,
+	.set_time = tps6594_rtc_set_time,
+	.read_alarm = tps6594_rtc_read_alarm,
+	.set_alarm = tps6594_rtc_set_alarm,
+	.alarm_irq_enable = tps6594_rtc_alarm_irq_enable,
+	.read_offset = tps6594_rtc_read_offset,
+	.set_offset = tps6594_rtc_set_offset,
+};
+
+static int tps6594_rtc_probe(struct platform_device *pdev)
+{
+	struct tps6594 *tps;
+	struct rtc_device *rtc;
+	int irq;
+	int ret;
+
+	tps = dev_get_drvdata(pdev->dev.parent);
+
+	rtc = devm_kzalloc(&pdev->dev, sizeof(*rtc), GFP_KERNEL);
+	if (!rtc)
+		return -ENOMEM;
+
+	rtc = devm_rtc_allocate_device(&pdev->dev);
+	if (IS_ERR(rtc))
+		return PTR_ERR(rtc);
+
+	/* Enable crystal oscillator */
+	ret = regmap_set_bits(tps->regmap, TPS6594_REG_RTC_CTRL_2,
+			      TPS6594_BIT_XTAL_EN);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_test_bits(tps->regmap, TPS6594_REG_RTC_STATUS,
+			       TPS6594_BIT_RUN);
+	if (ret < 0)
+		return ret;
+	/* RTC not running */
+	if (ret == 0) {
+		/* Start rtc */
+		ret = regmap_set_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+				      TPS6594_BIT_STOP_RTC);
+		if (ret < 0)
+			return ret;
+
+		mdelay(100);
+
+		/*
+		 * RTC should be running now. Check if this is the case.
+		 * If not it might be a missing oscillator.
+		 */
+		ret = regmap_test_bits(tps->regmap, TPS6594_REG_RTC_STATUS,
+				       TPS6594_BIT_RUN);
+		if (ret < 0)
+			return ret;
+		if (ret == 0)
+			return -ENODEV;
+
+		/* Stop RTC until first call to `tps6594_rtc_set_time */
+		ret = regmap_clear_bits(tps->regmap, TPS6594_REG_RTC_CTRL_1,
+					TPS6594_BIT_STOP_RTC);
+		if (ret < 0)
+			return ret;
+	}
+
+	platform_set_drvdata(pdev, rtc);
+
+	irq = platform_get_irq_byname(pdev, TPS6594_IRQ_NAME_ALARM);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Failed to get irq\n");
+		return irq;
+	}
+
+	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+					tps6594_rtc_interrupt, IRQF_ONESHOT,
+					TPS6594_IRQ_NAME_ALARM, &pdev->dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "Failed to request_threaded_irq\n");
+		return ret;
+	}
+
+	rtc->ops = &tps6594_rtc_ops;
+	rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
+	rtc->range_max = RTC_TIMESTAMP_END_2099;
+
+	return devm_rtc_register_device(rtc);
+}
+
+static struct platform_driver tps6594_rtc_driver = {
+	.probe		= tps6594_rtc_probe,
+	.driver		= {
+		.name	= "tps6594-rtc",
+	},
+};
+
+module_platform_driver(tps6594_rtc_driver);
+
+MODULE_ALIAS("platform:tps6594-rtc");
+MODULE_AUTHOR("Esteban Blanc <eblanc@baylibre.com>");
+MODULE_DESCRIPTION("TPS6594 RTC driver");
+MODULE_LICENSE("GPL");
-- 
2.39.2

[PATCH v3 2/3] pinctrl: tps6594: add for TPS6594 PMIC

[Esteban Blanc]

TI TPS6594 PMIC has 11 GPIOs which can be used for different
functions.

This add a pinctrl and pinmux drivers in order to use those functions.

Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 drivers/pinctrl/Kconfig           |  10 +
 drivers/pinctrl/Makefile          |   1 +
 drivers/pinctrl/pinctrl-tps6594.c | 365 ++++++++++++++++++++++++++++++
 3 files changed, 376 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-tps6594.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index dcb53c4a9584..2c1826e86a54 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -499,6 +499,16 @@ config PINCTRL_THUNDERBAY
 	  rate control and direction control. This module will be
 	  called as pinctrl-thunderbay.
 
+config PINCTRL_TPS6594
+	tristate "Pinctrl and GPIO driver for TI TPS6594 PMIC"
+	depends on MFD_TPS6594
+	default MFD_TPS6594
+	select PINMUX
+	select GPIOLIB
+	help
+	  This driver supports GPIOs and pinmuxing for the TPS6594
+	  PMICs chip family.
+
 config PINCTRL_ZYNQ
 	bool "Pinctrl driver for Xilinx Zynq"
 	depends on ARCH_ZYNQ
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index d5939840bb2a..ddaee9459da7 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_PINCTRL_STMFX) 	+= pinctrl-stmfx.o
 obj-$(CONFIG_PINCTRL_SX150X)	+= pinctrl-sx150x.o
 obj-$(CONFIG_PINCTRL_TB10X)	+= pinctrl-tb10x.o
 obj-$(CONFIG_PINCTRL_THUNDERBAY) += pinctrl-thunderbay.o
+obj-$(CONFIG_PINCTRL_TPS6594)	+= pinctrl-tps6594.o
 obj-$(CONFIG_PINCTRL_ZYNQMP)	+= pinctrl-zynqmp.o
 obj-$(CONFIG_PINCTRL_ZYNQ)	+= pinctrl-zynq.o
 
diff --git a/drivers/pinctrl/pinctrl-tps6594.c b/drivers/pinctrl/pinctrl-tps6594.c
new file mode 100644
index 000000000000..0f424cbd21a8
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-tps6594.c
@@ -0,0 +1,365 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Pinmux and GPIO driver for tps6594 PMIC
+ *
+ * Copyright (C) 2022 BayLibre Incorporated - https://www.baylibre.com/
+ */
+
+#include <linux/gpio/driver.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/pinmux.h>
+
+#include <linux/mfd/tps6594.h>
+
+#define TPS6594_GPIO_DIR_IN 0
+#define TPS6594_GPIO_DIR_OUT TPS6594_BIT_GPIO_DIR
+#define TPS6594_PINCTRL_PINS_NB 11
+
+#define TPS6594_PINCTRL_GPIO_FUNCTION 0
+#define TPS6594_PINCTRL_SCL_I2C2_CS_SPI_FUNCTION 1
+#define TPS6594_PINCTRL_TRIG_WDOG_FUNCTION 1
+#define TPS6594_PINCTRL_CLK32KOUT_FUNCTION 1
+#define TPS6594_PINCTRL_SCLK_SPMI_FUNCTION 1
+#define TPS6594_PINCTRL_SDATA_SPMI_FUNCTION 1
+#define TPS6594_PINCTRL_NERR_MCU_FUNCTION 1
+#define TPS6594_PINCTRL_PDOG_FUNCTION 1
+#define TPS6594_PINCTRL_SYNCCLKIN_FUNCTION 1
+#define TPS6594_PINCTRL_NRSTOUT_SOC_FUNCTION 2
+#define TPS6594_PINCTRL_SYNCCLKOUT_FUNCTION 2
+#define TPS6594_PINCTRL_SDA_I2C2_SDO_SPI_FUNCTION 2
+#define TPS6594_PINCTRL_NERR_SOC_FUNCTION 2
+#define TPS6594_PINCTRL_DISABLE_WDOG_FUNCTION 3
+#define TPS6594_PINCTRL_NSLEEP1_FUNCTION 4
+#define TPS6594_PINCTRL_NSLEEP2_FUNCTION 5
+#define TPS6594_PINCTRL_WKUP1_FUNCTION 6
+#define TPS6594_PINCTRL_WKUP2_FUNCTION 7
+
+/* Special muxval for recalcitrant pins */
+#define TPS6594_PINCTRL_DISABLE_WDOG_FUNCTION_GPIO8 2
+#define TPS6594_PINCTRL_SYNCCLKOUT_FUNCTION_GPIO8 3
+#define TPS6594_PINCTRL_CLK32KOUT_FUNCTION_GPIO9 3
+
+#define TPS6594_OFFSET_GPIO_SEL 5
+
+static const struct pinctrl_pin_desc tps6594_pins[TPS6594_PINCTRL_PINS_NB] = {
+	PINCTRL_PIN(0, "GPIO0"),   PINCTRL_PIN(1, "GPIO1"),
+	PINCTRL_PIN(2, "GPIO2"),   PINCTRL_PIN(3, "GPIO3"),
+	PINCTRL_PIN(4, "GPIO4"),   PINCTRL_PIN(5, "GPIO5"),
+	PINCTRL_PIN(6, "GPIO6"),   PINCTRL_PIN(7, "GPIO7"),
+	PINCTRL_PIN(8, "GPIO8"),   PINCTRL_PIN(9, "GPIO9"),
+	PINCTRL_PIN(10, "GPIO10"),
+};
+
+static const char *groups_name[TPS6594_PINCTRL_PINS_NB] = {
+	"GPIO0", "GPIO1", "GPIO2", "GPIO3", "GPIO4", "GPIO5",
+	"GPIO6", "GPIO7", "GPIO8", "GPIO9", "GPIO10"
+};
+
+struct tps6594_pinctrl_function {
+	const char *name;
+	u8 muxval;
+	const char **groups;
+	unsigned long ngroups;
+};
+
+static const struct tps6594_pinctrl_function pinctrl_functions[] = {
+	{ "gpio", TPS6594_PINCTRL_GPIO_FUNCTION, groups_name,
+	  TPS6594_PINCTRL_PINS_NB },
+	{ "nsleep1", TPS6594_PINCTRL_NSLEEP1_FUNCTION, groups_name,
+	  TPS6594_PINCTRL_PINS_NB },
+	{ "nsleep2", TPS6594_PINCTRL_NSLEEP2_FUNCTION, groups_name,
+	  TPS6594_PINCTRL_PINS_NB },
+	{ "wkup1", TPS6594_PINCTRL_WKUP1_FUNCTION, groups_name,
+	  TPS6594_PINCTRL_PINS_NB },
+	{ "wkup2", TPS6594_PINCTRL_WKUP2_FUNCTION, groups_name,
+	  TPS6594_PINCTRL_PINS_NB },
+	{ "scl_i2c2-cs_spi", TPS6594_PINCTRL_SCL_I2C2_CS_SPI_FUNCTION,
+	  (const char *[]){ "GPIO0", "GPIO1" }, 2 },
+	{ "nrstout_soc", TPS6594_PINCTRL_NRSTOUT_SOC_FUNCTION,
+	  (const char *[]){ "GPIO0", "GPIO10" }, 2 },
+	{ "trig_wdog", TPS6594_PINCTRL_TRIG_WDOG_FUNCTION,
+	  (const char *[]){ "GPIO1", "GPIO10" }, 2 },
+	{ "sda_i2c2-sdo_spi", TPS6594_PINCTRL_SDA_I2C2_SDO_SPI_FUNCTION,
+	  (const char *[]){ "GPIO1" }, 1 },
+	{ "clk32kout", TPS6594_PINCTRL_CLK32KOUT_FUNCTION,
+	  (const char *[]){ "GPIO2", "GPIO3", "GPIO7" }, 3 },
+	{ "nerr_soc", TPS6594_PINCTRL_NERR_SOC_FUNCTION,
+	  (const char *[]){ "GPIO2" }, 1 },
+	{ "sclk_spmi", TPS6594_PINCTRL_SCLK_SPMI_FUNCTION,
+	  (const char *[]){ "GPIO4" }, 1 },
+	{ "sdata_spmi", TPS6594_PINCTRL_SDATA_SPMI_FUNCTION,
+	  (const char *[]){ "GPIO5" }, 1 },
+	{ "nerr_mcu", TPS6594_PINCTRL_NERR_MCU_FUNCTION,
+	  (const char *[]){ "GPIO6" }, 1 },
+	{ "syncclkout", TPS6594_PINCTRL_SYNCCLKOUT_FUNCTION,
+	  (const char *[]){ "GPIO7", "GPIO9" }, 2 },
+	{ "disable_wdog", TPS6594_PINCTRL_DISABLE_WDOG_FUNCTION,
+	  (const char *[]){ "GPIO7", "GPIO8" }, 2 },
+	{ "pdog", TPS6594_PINCTRL_PDOG_FUNCTION, (const char *[]){ "GPIO8" },
+	  1 },
+	{ "syncclkin", TPS6594_PINCTRL_SYNCCLKIN_FUNCTION,
+	  (const char *[]){ "GPIO9" }, 1 },
+};
+
+struct tps6594_pinctrl {
+	struct tps6594 *tps;
+	struct gpio_chip gpio_chip;
+	struct pinctrl_dev *pctl_dev;
+	const struct tps6594_pinctrl_function *funcs;
+	const struct pinctrl_pin_desc *pins;
+};
+
+static int tps6594_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+	struct tps6594_pinctrl *pinctrl = gpiochip_get_data(gc);
+	int ret, val;
+
+	ret = regmap_read(pinctrl->tps->regmap, TPS6594_REG_GPIOX_IN(offset),
+			  &val);
+	if (ret < 0)
+		return ret;
+
+	val = (val & TPS6594_BIT_GPIOX_IN(offset)) > 0;
+
+	return val;
+}
+
+static void tps6594_gpio_set(struct gpio_chip *gc, unsigned int offset,
+			     int value)
+{
+	struct tps6594_pinctrl *pinctrl = gpiochip_get_data(gc);
+	unsigned int set_register = TPS6594_REG_GPIOX_OUT(offset);
+	int ret;
+
+	ret = regmap_update_bits(pinctrl->tps->regmap, set_register,
+				 TPS6594_BIT_GPIOX_OUT(offset),
+				 value ? TPS6594_BIT_GPIOX_OUT(offset) : 0);
+	if (ret < 0)
+		dev_err(pinctrl->tps->dev,
+			"gpio_set failed to set GPIO%d to %d: %d\n", offset,
+			value, ret);
+}
+
+static int tps6594_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	struct tps6594_pinctrl *pinctrl = gpiochip_get_data(gc);
+	int ret;
+
+	ret = regmap_test_bits(pinctrl->tps->regmap,
+			       TPS6594_REG_GPIOX_CONF(offset),
+			       TPS6594_BIT_GPIO_DIR);
+	if (ret < 0) {
+		dev_err(pinctrl->tps->dev,
+			"gpio_get_direction for GPIO%d failed: %d\n", offset,
+			ret);
+		return ret;
+	}
+
+	/*
+	 * TPS6594 direction is 0 = input and 1 = output but Linux direction is 0 = output and
+	 * 1 = input
+	 * Let's invert our value
+	 */
+	return !ret;
+}
+
+static int tps6594_gpio_change_direction(struct gpio_chip *gc,
+					 unsigned int offset,
+					 unsigned int direction)
+{
+	struct tps6594_pinctrl *pinctrl = gpiochip_get_data(gc);
+	int ret;
+
+	ret = regmap_update_bits(pinctrl->tps->regmap,
+				 TPS6594_REG_GPIOX_CONF(offset),
+				 TPS6594_BIT_GPIO_DIR, direction);
+	if (ret < 0)
+		dev_err(pinctrl->tps->dev,
+			"gpio_change_direction for GPIO%d to %u direction failed: %d\n",
+			offset, direction, ret);
+
+	return ret;
+}
+
+static int tps6594_gpio_direction_input(struct gpio_chip *gc,
+					unsigned int offset)
+{
+	return tps6594_gpio_change_direction(gc, offset, TPS6594_GPIO_DIR_IN);
+}
+
+static int tps6594_gpio_direction_output(struct gpio_chip *gc,
+					 unsigned int offset, int value)
+{
+	tps6594_gpio_set(gc, offset, value);
+
+	return tps6594_gpio_change_direction(gc, offset, TPS6594_GPIO_DIR_OUT);
+}
+
+static const struct gpio_chip template_gpio_chip = {
+	.label = "tps6594-gpio",
+	.owner = THIS_MODULE,
+	.get_direction = tps6594_gpio_get_direction,
+	.direction_input = tps6594_gpio_direction_input,
+	.direction_output = tps6594_gpio_direction_output,
+	.get = tps6594_gpio_get,
+	.set = tps6594_gpio_set,
+	.base = -1,
+	.ngpio = TPS6594_PINCTRL_PINS_NB,
+	.can_sleep = true,
+};
+
+static int tps6594_pmx_func_cnt(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(pinctrl_functions);
+}
+
+static const char *tps6594_pmx_func_name(struct pinctrl_dev *pctldev,
+					 unsigned int selector)
+{
+	struct tps6594_pinctrl *pinctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pinctrl->funcs[selector].name;
+}
+
+static int tps6594_pmx_func_groups(struct pinctrl_dev *pctldev,
+				   unsigned int selector,
+				   const char *const **groups,
+				   unsigned int *num_groups)
+{
+	struct tps6594_pinctrl *pinctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	*groups = pinctrl->funcs[selector].groups;
+	*num_groups = pinctrl->funcs[selector].ngroups;
+
+	return 0;
+}
+
+static int tps6594_pmx_set(struct tps6594_pinctrl *pinctrl, unsigned int pin,
+			   u8 muxval)
+{
+	u8 mux_sel_val = muxval << TPS6594_OFFSET_GPIO_SEL;
+
+	return regmap_update_bits(pinctrl->tps->regmap,
+				  TPS6594_REG_GPIOX_CONF(pin),
+				  TPS6594_MASK_GPIO_SEL, mux_sel_val);
+}
+
+static int tps6594_pmx_set_mux(struct pinctrl_dev *pctldev,
+			       unsigned int function, unsigned int group)
+{
+	struct tps6594_pinctrl *pinctrl = pinctrl_dev_get_drvdata(pctldev);
+	u8 muxval = pinctrl->funcs[function].muxval;
+
+	/* Some pins don't have the same muxval for the same function... */
+	if (group == 8) {
+		if (muxval == TPS6594_PINCTRL_DISABLE_WDOG_FUNCTION)
+			muxval = TPS6594_PINCTRL_DISABLE_WDOG_FUNCTION_GPIO8;
+		else if (muxval == TPS6594_PINCTRL_SYNCCLKOUT_FUNCTION)
+			muxval = TPS6594_PINCTRL_SYNCCLKOUT_FUNCTION_GPIO8;
+	} else if (group == 9) {
+		if (muxval == TPS6594_PINCTRL_CLK32KOUT_FUNCTION)
+			muxval = TPS6594_PINCTRL_CLK32KOUT_FUNCTION_GPIO9;
+	}
+
+	return tps6594_pmx_set(pinctrl, group, muxval);
+}
+
+static int tps6594_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
+					  struct pinctrl_gpio_range *range,
+					  unsigned int offset, bool input)
+{
+	struct tps6594_pinctrl *pinctrl = pinctrl_dev_get_drvdata(pctldev);
+	u8 muxval = pinctrl->funcs[TPS6594_PINCTRL_GPIO_FUNCTION].muxval;
+
+	return tps6594_pmx_set(pinctrl, offset, muxval);
+}
+
+static const struct pinmux_ops tps6594_pmx_ops = {
+	.get_functions_count = tps6594_pmx_func_cnt,
+	.get_function_name = tps6594_pmx_func_name,
+	.get_function_groups = tps6594_pmx_func_groups,
+	.set_mux = tps6594_pmx_set_mux,
+	.gpio_set_direction = tps6594_pmx_gpio_set_direction,
+	.strict = true,
+};
+
+static int tps6594_groups_cnt(struct pinctrl_dev *pctldev)
+{
+	return ARRAY_SIZE(tps6594_pins);
+}
+
+static int tps6594_group_pins(struct pinctrl_dev *pctldev,
+			      unsigned int selector, const unsigned int **pins,
+			      unsigned int *num_pins)
+{
+	struct tps6594_pinctrl *pinctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	*pins = (unsigned int *)&pinctrl->pins[selector];
+	*num_pins = 1;
+
+	return 0;
+}
+
+static const char *tps6594_group_name(struct pinctrl_dev *pctldev,
+				      unsigned int selector)
+{
+	struct tps6594_pinctrl *pinctrl = pinctrl_dev_get_drvdata(pctldev);
+
+	return pinctrl->pins[selector].name;
+}
+
+static const struct pinctrl_ops tps6594_pctrl_ops = {
+	.dt_node_to_map = pinconf_generic_dt_node_to_map_group,
+	.dt_free_map = pinconf_generic_dt_free_map,
+	.get_groups_count = tps6594_groups_cnt,
+	.get_group_name = tps6594_group_name,
+	.get_group_pins = tps6594_group_pins,
+};
+
+static int tps6594_pinctrl_probe(struct platform_device *pdev)
+{
+	struct tps6594 *tps = dev_get_drvdata(pdev->dev.parent);
+	struct tps6594_pinctrl *pinctrl;
+	struct pinctrl_desc *pctrl_desc;
+
+	pinctrl = devm_kzalloc(&pdev->dev, sizeof(*pinctrl), GFP_KERNEL);
+	if (!pinctrl)
+		return -ENOMEM;
+
+	pinctrl->tps = dev_get_drvdata(pdev->dev.parent);
+	pinctrl->gpio_chip = template_gpio_chip;
+	pinctrl->gpio_chip.parent = tps->dev;
+
+	pctrl_desc = devm_kzalloc(&pdev->dev, sizeof(*pctrl_desc), GFP_KERNEL);
+	if (!pctrl_desc)
+		return -ENOMEM;
+
+	pctrl_desc->name = dev_name(&pdev->dev);
+	pctrl_desc->owner = THIS_MODULE;
+	pctrl_desc->pins = tps6594_pins;
+	pctrl_desc->npins = ARRAY_SIZE(tps6594_pins);
+	pctrl_desc->pctlops = &tps6594_pctrl_ops;
+	pctrl_desc->pmxops = &tps6594_pmx_ops;
+	pinctrl->funcs = pinctrl_functions;
+	pinctrl->pins = tps6594_pins;
+	pinctrl->pctl_dev =
+		devm_pinctrl_register(&pdev->dev, pctrl_desc, pinctrl);
+	if (IS_ERR(pinctrl->pctl_dev)) {
+		dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
+		return PTR_ERR(pinctrl->pctl_dev);
+	}
+
+	return devm_gpiochip_add_data(&pdev->dev, &pinctrl->gpio_chip, pinctrl);
+}
+
+static struct platform_driver tps6594_pinctrl_driver = {
+	.driver = { .name = "tps6594-pinctrl" },
+	.probe = tps6594_pinctrl_probe,
+};
+module_platform_driver(tps6594_pinctrl_driver);
+
+MODULE_ALIAS("platform:tps6594-pinctrl");
+MODULE_AUTHOR("Esteban Blanc <eblanc@baylibre.com>");
+MODULE_DESCRIPTION("TPS6594 pinctrl and GPIO driver");
+MODULE_LICENSE("GPL");
-- 
2.39.2

[PATCH v3 3/3] regulator: tps6594-regulator: Add driver for TI TPS6594 regulators

[Esteban Blanc]

From: Jerome Neanne <jneanne@baylibre.com>

This patch adds support for TPS6594 regulators (bucks and LDOs).
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Bucks can be used in single or multiphase mode, depending on PMIC
part number.

Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
 drivers/regulator/Kconfig             |  13 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/tps6594-regulator.c | 620 ++++++++++++++++++++++++++
 3 files changed, 634 insertions(+)
 create mode 100644 drivers/regulator/tps6594-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index aae28d0a489c..5f01132b04e1 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1440,6 +1440,19 @@ config REGULATOR_TPS65219
 	  voltage regulators. It supports software based voltage control
 	  for different voltage domains.
 
+config REGULATOR_TPS6594
+	tristate "TI TPS6594 Power regulators"
+	depends on MFD_TPS6594 && OF
+	default MFD_TPS6594
+	help
+	  This driver supports TPS6594 voltage regulator chips.
+	  TPS6594 series of PMICs have 5 BUCKs and 4 LDOs
+	  voltage regulators.
+	  BUCKs 1,2,3,4 can be used in single phase or multiphase mode.
+	  Part number defines which single or multiphase mode is i used.
+	  It supports software based voltage control
+	  for different voltage domains.
+
 config REGULATOR_TPS6524X
 	tristate "TI TPS6524X Power regulators"
 	depends on SPI
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index ee383d8fc835..cb420adf7670 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -172,6 +172,7 @@ obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6586X) += tps6586x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65910) += tps65910-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65912) += tps65912-regulator.o
+obj-$(CONFIG_REGULATOR_TPS6594) += tps6594-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65132) += tps65132-regulator.o
 obj-$(CONFIG_REGULATOR_TPS68470) += tps68470-regulator.o
 obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o twl6030-regulator.o
diff --git a/drivers/regulator/tps6594-regulator.c b/drivers/regulator/tps6594-regulator.c
new file mode 100644
index 000000000000..f01685dec87a
--- /dev/null
+++ b/drivers/regulator/tps6594-regulator.c
@@ -0,0 +1,620 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Regulator driver for tps6594 PMIC
+//
+// Copyright (C) 2023 BayLibre Incorporated - https://www.baylibre.com/
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+#include <linux/mfd/tps6594.h>
+
+#define BUCK_NB		5
+#define LDO_NB		4
+#define MULTI_PHASE_NB	4
+#define REGS_INT_NB	4
+
+enum tps6594_regulator_id {
+	/* DCDC's */
+	TPS6594_BUCK_1,
+	TPS6594_BUCK_2,
+	TPS6594_BUCK_3,
+	TPS6594_BUCK_4,
+	TPS6594_BUCK_5,
+
+	/* LDOs */
+	TPS6594_LDO_1,
+	TPS6594_LDO_2,
+	TPS6594_LDO_3,
+	TPS6594_LDO_4,
+};
+
+enum tps6594_multi_regulator_id {
+	/* Multi-phase DCDC's */
+	TPS6594_BUCK_12,
+	TPS6594_BUCK_34,
+	TPS6594_BUCK_123,
+	TPS6594_BUCK_1234,
+};
+
+struct tps6594_regulator_irq_type {
+	const char *irq_name;
+	const char *regulator_name;
+	const char *event_name;
+	unsigned long event;
+};
+
+static struct tps6594_regulator_irq_type tps6594_ext_regulator_irq_types[] = {
+	{ TPS6594_IRQ_NAME_VCCA_OV, "VCCA", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_VCCA_UV, "VCCA", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_VMON1_OV, "VMON1", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_VMON1_UV, "VMON1", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_VMON1_RV, "VMON1", "residual voltage",
+	  REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_VMON2_OV, "VMON2", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_VMON2_UV, "VMON2", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_VMON2_RV, "VMON2", "residual voltage",
+	  REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+};
+
+struct tps6594_regulator_irq_data {
+	struct device *dev;
+	struct tps6594_regulator_irq_type *type;
+	struct regulator_dev *rdev;
+};
+
+struct tps6594_ext_regulator_irq_data {
+	struct device *dev;
+	struct tps6594_regulator_irq_type *type;
+};
+
+#define TPS6594_REGULATOR(_name, _of, _id, _type, _ops, _n, _vr, _vm, _er, \
+			   _em, _cr, _cm, _lr, _nlr, _delay, _fuv, \
+			   _ct, _ncl, _bpm) \
+	{								\
+		.name			= _name,			\
+		.of_match		= _of,				\
+		.regulators_node	= of_match_ptr("regulators"),	\
+		.supply_name		= _of,				\
+		.id			= _id,				\
+		.ops			= &(_ops),			\
+		.n_voltages		= _n,				\
+		.type			= _type,			\
+		.owner			= THIS_MODULE,			\
+		.vsel_reg		= _vr,				\
+		.vsel_mask		= _vm,				\
+		.csel_reg		= _cr,				\
+		.csel_mask		= _cm,				\
+		.curr_table		= _ct,				\
+		.n_current_limits	= _ncl,				\
+		.enable_reg		= _er,				\
+		.enable_mask		= _em,				\
+		.volt_table		= NULL,				\
+		.linear_ranges		= _lr,				\
+		.n_linear_ranges	= _nlr,				\
+		.ramp_delay		= _delay,			\
+		.fixed_uV		= _fuv,				\
+		.bypass_reg		= _vr,				\
+		.bypass_mask		= _bpm,				\
+	}								\
+
+static const struct linear_range bucks_ranges[] = {
+	REGULATOR_LINEAR_RANGE(300000, 0x0, 0xe, 20000),
+	REGULATOR_LINEAR_RANGE(600000, 0xf, 0x72, 5000),
+	REGULATOR_LINEAR_RANGE(1100000, 0x73, 0xaa, 10000),
+	REGULATOR_LINEAR_RANGE(1660000, 0xab, 0xff, 20000),
+};
+
+static const struct linear_range ldos_1_2_3_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, 0x4, 0x3a, 50000),
+};
+
+static const struct linear_range ldos_4_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0x20, 0x74, 25000),
+};
+
+/* Operations permitted on BUCK1/2/3/4/5 */
+static const struct regulator_ops tps6594_bucks_ops = {
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+
+};
+
+/* Operations permitted on LDO1/2/3 */
+static const struct regulator_ops tps6594_ldos_1_2_3_ops = {
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.set_bypass		= regulator_set_bypass_regmap,
+	.get_bypass		= regulator_get_bypass_regmap,
+};
+
+/* Operations permitted on LDO4 */
+static const struct regulator_ops tps6594_ldos_4_ops = {
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+};
+
+static const struct regulator_desc buck_regs[] = {
+	TPS6594_REGULATOR("BUCK1", "buck1", TPS6594_BUCK_1,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(0),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(0),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 0, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK2", "buck2", TPS6594_BUCK_2,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(1),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(1),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 0, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK3", "buck3", TPS6594_BUCK_3,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(2),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(2),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 0, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK4", "buck4", TPS6594_BUCK_4,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(3),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(3),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 0, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK5", "buck5", TPS6594_BUCK_5,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(4),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(4),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 0, 0, NULL, 0, 0),
+};
+
+static struct tps6594_regulator_irq_type tps6594_buck1_irq_types[] = {
+	{ TPS6594_IRQ_NAME_BUCK1_OV, "BUCK1", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_BUCK1_UV, "BUCK1", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_BUCK1_SC, "BUCK1", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_BUCK1_ILIM, "BUCK1", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_buck2_irq_types[] = {
+	{ TPS6594_IRQ_NAME_BUCK2_OV, "BUCK2", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_BUCK2_UV, "BUCK2", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_BUCK2_SC, "BUCK2", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_BUCK2_ILIM, "BUCK2", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_buck3_irq_types[] = {
+	{ TPS6594_IRQ_NAME_BUCK3_OV, "BUCK3", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_BUCK3_UV, "BUCK3", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_BUCK3_SC, "BUCK3", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_BUCK3_ILIM, "BUCK3", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_buck4_irq_types[] = {
+	{ TPS6594_IRQ_NAME_BUCK4_OV, "BUCK4", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_BUCK4_UV, "BUCK4", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_BUCK4_SC, "BUCK4", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_BUCK4_ILIM, "BUCK4", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_buck5_irq_types[] = {
+	{ TPS6594_IRQ_NAME_BUCK5_OV, "BUCK5", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_BUCK5_UV, "BUCK5", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_BUCK5_SC, "BUCK5", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_BUCK5_ILIM, "BUCK5", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_ldo1_irq_types[] = {
+	{ TPS6594_IRQ_NAME_LDO1_OV, "LDO1", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_LDO1_UV, "LDO1", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_LDO1_SC, "LDO1", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_LDO1_ILIM, "LDO1", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_ldo2_irq_types[] = {
+	{ TPS6594_IRQ_NAME_LDO2_OV, "LDO2", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_LDO2_UV, "LDO2", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_LDO2_SC, "LDO2", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_LDO2_ILIM, "LDO2", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_ldo3_irq_types[] = {
+	{ TPS6594_IRQ_NAME_LDO3_OV, "LDO3", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_LDO3_UV, "LDO3", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_LDO3_SC, "LDO3", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_LDO3_ILIM, "LDO3", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type tps6594_ldo4_irq_types[] = {
+	{ TPS6594_IRQ_NAME_LDO4_OV, "LDO4", "overvoltage", REGULATOR_EVENT_OVER_VOLTAGE_WARN },
+	{ TPS6594_IRQ_NAME_LDO4_UV, "LDO4", "undervoltage", REGULATOR_EVENT_UNDER_VOLTAGE },
+	{ TPS6594_IRQ_NAME_LDO4_SC, "LDO4", "short circuit", REGULATOR_EVENT_REGULATION_OUT },
+	{ TPS6594_IRQ_NAME_LDO4_ILIM, "LDO4", "reach ilim, overcurrent",
+	  REGULATOR_EVENT_OVER_CURRENT },
+};
+
+static struct tps6594_regulator_irq_type *tps6594_bucks_irq_types[] = {
+	tps6594_buck1_irq_types,
+	tps6594_buck2_irq_types,
+	tps6594_buck3_irq_types,
+	tps6594_buck4_irq_types,
+	tps6594_buck5_irq_types,
+};
+
+static struct tps6594_regulator_irq_type *tps6594_ldos_irq_types[] = {
+	tps6594_ldo1_irq_types,
+	tps6594_ldo2_irq_types,
+	tps6594_ldo3_irq_types,
+	tps6594_ldo4_irq_types,
+};
+
+static const struct regulator_desc multi_regs[] = {
+	TPS6594_REGULATOR("BUCK12", "buck12", TPS6594_BUCK_1,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(1),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(1),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 4000, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK34", "buck34", TPS6594_BUCK_3,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(3),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(3),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 0, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK123", "buck123", TPS6594_BUCK_1,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(1),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(1),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 4000, 0, NULL, 0, 0),
+	TPS6594_REGULATOR("BUCK1234", "buck1234", TPS6594_BUCK_1,
+			  REGULATOR_VOLTAGE, tps6594_bucks_ops, TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_VOUT_1(1),
+			  TPS6594_MASK_BUCKS_VSET,
+			  TPS6594_REG_BUCKX_CTRL(1),
+			  TPS6594_BIT_BUCK_EN, 0, 0, bucks_ranges,
+			  4, 4000, 0, NULL, 0, 0),
+};
+
+static const struct regulator_desc ldo_regs[] = {
+	TPS6594_REGULATOR("LDO1", "ldo1", TPS6594_LDO_1,
+			  REGULATOR_VOLTAGE, tps6594_ldos_1_2_3_ops, TPS6594_MASK_LDO123_VSET,
+			  TPS6594_REG_LDOX_VOUT(0),
+			  TPS6594_MASK_LDO123_VSET,
+			  TPS6594_REG_LDOX_CTRL(0),
+			  TPS6594_BIT_LDO_EN, 0, 0, ldos_1_2_3_ranges,
+			  1, 0, 0, NULL, 0, TPS6594_BIT_LDO_BYPASS),
+	TPS6594_REGULATOR("LDO2", "ldo2", TPS6594_LDO_2,
+			  REGULATOR_VOLTAGE, tps6594_ldos_1_2_3_ops, TPS6594_MASK_LDO123_VSET,
+			  TPS6594_REG_LDOX_VOUT(1),
+			  TPS6594_MASK_LDO123_VSET,
+			  TPS6594_REG_LDOX_CTRL(1),
+			  TPS6594_BIT_LDO_EN, 0, 0, ldos_1_2_3_ranges,
+			  1, 0, 0, NULL, 0, TPS6594_BIT_LDO_BYPASS),
+	TPS6594_REGULATOR("LDO3", "ldo3", TPS6594_LDO_3,
+			  REGULATOR_VOLTAGE, tps6594_ldos_1_2_3_ops, TPS6594_MASK_LDO123_VSET,
+			  TPS6594_REG_LDOX_VOUT(2),
+			  TPS6594_MASK_LDO123_VSET,
+			  TPS6594_REG_LDOX_CTRL(2),
+			  TPS6594_BIT_LDO_EN, 0, 0, ldos_1_2_3_ranges,
+			  1, 0, 0, NULL, 0, TPS6594_BIT_LDO_BYPASS),
+	TPS6594_REGULATOR("LDO4", "ldo4", TPS6594_LDO_4,
+			  REGULATOR_VOLTAGE, tps6594_ldos_4_ops, TPS6594_MASK_LDO4_VSET >> 1,
+			  TPS6594_REG_LDOX_VOUT(3),
+			  TPS6594_MASK_LDO4_VSET,
+			  TPS6594_REG_LDOX_CTRL(3),
+			  TPS6594_BIT_LDO_EN, 0, 0, ldos_4_ranges,
+			  1, 0, 0, NULL, 0, 0),
+};
+
+static irqreturn_t tps6594_regulator_irq_handler(int irq, void *data)
+{
+	struct tps6594_regulator_irq_data *irq_data = data;
+
+	if (irq_data->type->event_name[0] == '\0') {
+		/* This is the timeout interrupt no specific regulator */
+		dev_err(irq_data->dev,
+			"System was put in shutdown due to timeout during an active or standby transition.\n");
+		return IRQ_HANDLED;
+	}
+
+	dev_err(irq_data->dev, "Error IRQ trap %s for %s\n",
+		irq_data->type->event_name, irq_data->type->regulator_name);
+
+	regulator_notifier_call_chain(irq_data->rdev,
+				      irq_data->type->event, NULL);
+
+	return IRQ_HANDLED;
+}
+
+static int tps6594_request_reg_irqs(struct platform_device *pdev,
+				    struct regulator_dev *rdev,
+				    struct tps6594_regulator_irq_data *irq_data,
+				    struct tps6594_regulator_irq_type *tps6594_regs_irq_types,
+				    int *irq_idx)
+{
+	struct tps6594_regulator_irq_type *irq_type;
+	struct tps6594 *tps = dev_get_drvdata(pdev->dev.parent);
+	int j;
+	int irq;
+	int error;
+
+	for (j = 0; j < REGS_INT_NB; j++) {
+		irq_type = &tps6594_regs_irq_types[j];
+		irq = platform_get_irq_byname(pdev, irq_type->irq_name);
+		if (irq < 0)
+			return -EINVAL;
+
+		irq_data[*irq_idx + j].dev = tps->dev;
+		irq_data[*irq_idx + j].type = irq_type;
+		irq_data[*irq_idx + j].rdev = rdev;
+
+		error = devm_request_threaded_irq(tps->dev, irq, NULL,
+						  tps6594_regulator_irq_handler,
+						  IRQF_ONESHOT,
+						  irq_type->irq_name,
+						  &irq_data[*irq_idx]);
+		(*irq_idx)++;
+		if (error) {
+			dev_err(tps->dev, "tps6594 failed to request %s IRQ %d: %d\n",
+				irq_type->irq_name, irq, error);
+			return error;
+		}
+	}
+	return 0;
+}
+
+static int tps6594_regulator_probe(struct platform_device *pdev)
+{
+	struct tps6594 *tps = dev_get_drvdata(pdev->dev.parent);
+	struct regulator_dev *rdev;
+	struct device_node *np = NULL;
+	struct device_node *np_pmic_parent = NULL;
+	struct regulator_config config = {};
+	struct tps6594_regulator_irq_data *irq_data;
+	struct tps6594_ext_regulator_irq_data *irq_ext_reg_data;
+	struct tps6594_regulator_irq_type *irq_type;
+	u8 buck_configured[BUCK_NB] = { 0 };
+	u8 buck_multi[MULTI_PHASE_NB] = { 0 };
+	static const char *multiphases[] = {"buck12", "buck123", "buck1234", "buck34"};
+	static const char *npname;
+	int error, i, irq, multi, delta;
+	int irq_idx = 0;
+	int buck_idx = 0;
+	int ext_reg_irq_nb = 2;
+
+	enum {
+	MULTI_BUCK12,
+	MULTI_BUCK123,
+	MULTI_BUCK1234,
+	MULTI_BUCK12_34,
+	MULTI_FIRST = MULTI_BUCK12,
+	MULTI_LAST = MULTI_BUCK12_34,
+	MULTI_NUM = MULTI_LAST - MULTI_FIRST + 1
+	};
+
+	config.dev = tps->dev;
+	config.driver_data = tps;
+	config.regmap = tps->regmap;
+
+	/*
+	 * Switch case defines different possible multi phase config
+	 * This is based on dts buck node name.
+	 * Buck node name must be chosen accordingly.
+	 * Default case is no Multiphase buck.
+	 * In case of Multiphase configuration, value should be defined for
+	 * buck_configured to avoid creating bucks for every buck in multiphase
+	 */
+	for (multi = MULTI_FIRST ; multi < MULTI_NUM ; multi++) {
+		np = of_find_node_by_name(tps->dev->of_node, multiphases[multi]);
+		npname = of_node_full_name(np);
+		np_pmic_parent = of_get_parent(of_get_parent(np));
+		if (strcmp((of_node_full_name(np_pmic_parent)), tps->dev->of_node->full_name))
+			continue;
+		delta = strcmp(npname, multiphases[multi]);
+		if (!delta) {
+			switch (multi) {
+			case MULTI_BUCK12:
+				buck_multi[0] = 1;
+				buck_configured[0] = 1;
+				buck_configured[1] = 1;
+				break;
+			/* multiphase buck34 is supported only with buck12 */
+			case MULTI_BUCK12_34:
+				buck_multi[0] = 1;
+				buck_configured[0] = 1;
+				buck_configured[1] = 1;
+				buck_multi[1] = 1;
+				buck_configured[2] = 1;
+				buck_configured[3] = 1;
+				break;
+			case MULTI_BUCK123:
+				buck_multi[2] = 1;
+				buck_configured[0] = 1;
+				buck_configured[1] = 1;
+				buck_configured[2] = 1;
+				break;
+			case MULTI_BUCK1234:
+				buck_multi[3] = 1;
+				buck_configured[0] = 1;
+				buck_configured[1] = 1;
+				buck_configured[2] = 1;
+				buck_configured[3] = 1;
+				break;
+			}
+		}
+	}
+
+	if (tps->chip_id == LP8764)
+		/* There is only 4 buck on LP8764 */
+		buck_configured[4] = 1;
+
+	irq_data = devm_kmalloc(tps->dev,
+				ARRAY_SIZE(tps6594_bucks_irq_types) *
+				REGS_INT_NB *
+				sizeof(struct tps6594_regulator_irq_data) +
+				ARRAY_SIZE(tps6594_ldos_irq_types) *
+				REGS_INT_NB *
+				sizeof(struct tps6594_regulator_irq_data),
+				GFP_KERNEL);
+	if (!irq_data)
+		return -ENOMEM;
+
+	for (i = 0; i < MULTI_PHASE_NB; i++) {
+		if (buck_multi[i] == 0)
+			continue;
+
+		rdev = devm_regulator_register(&pdev->dev, &multi_regs[i], &config);
+		if (IS_ERR(rdev)) {
+			dev_err(tps->dev, "failed to register %s regulator\n",
+				pdev->name);
+			return PTR_ERR(rdev);
+		}
+		/* config multiphase buck12+buck34 */
+		if (i == 1)
+			buck_idx = 2;
+		error = tps6594_request_reg_irqs(pdev, rdev, irq_data,
+						 tps6594_bucks_irq_types[buck_idx], &irq_idx);
+		if (error)
+			return error;
+		error = tps6594_request_reg_irqs(pdev, rdev, irq_data,
+						 tps6594_bucks_irq_types[buck_idx + 1], &irq_idx);
+		if (error)
+			return error;
+
+		if (i == 2 || i == 3) {
+			error = tps6594_request_reg_irqs(pdev, rdev, irq_data,
+							 tps6594_bucks_irq_types[buck_idx + 2],
+							 &irq_idx);
+			if (error)
+				return error;
+		}
+		if (i == 3) {
+			error = tps6594_request_reg_irqs(pdev, rdev, irq_data,
+							 tps6594_bucks_irq_types[buck_idx + 3],
+							 &irq_idx);
+			if (error)
+				return error;
+		}
+	}
+
+	for (i = 0; i < BUCK_NB; i++) {
+		if (buck_configured[i] == 1)
+			continue;
+
+		rdev = devm_regulator_register(&pdev->dev, &buck_regs[i], &config);
+		if (IS_ERR(rdev)) {
+			dev_err(tps->dev, "failed to register %s regulator\n",
+				pdev->name);
+			return PTR_ERR(rdev);
+		}
+		error = tps6594_request_reg_irqs(pdev, rdev, irq_data,
+						 tps6594_bucks_irq_types[i], &irq_idx);
+		if (error)
+			return error;
+	}
+
+	/* LP8764 dosen't have LDO */
+	if (tps->chip_id != LP8764) {
+		for (i = 0; i < ARRAY_SIZE(ldo_regs); i++) {
+			rdev = devm_regulator_register(&pdev->dev, &ldo_regs[i], &config);
+			if (IS_ERR(rdev)) {
+				dev_err(tps->dev,
+					"failed to register %s regulator\n",
+					pdev->name);
+				return PTR_ERR(rdev);
+			}
+			error = tps6594_request_reg_irqs(pdev, rdev, irq_data,
+							 tps6594_ldos_irq_types[i],
+							 &irq_idx);
+			if (error)
+				return error;
+		}
+	}
+
+	if (tps->chip_id == LP8764)
+		ext_reg_irq_nb = ARRAY_SIZE(tps6594_ext_regulator_irq_types);
+
+	irq_ext_reg_data = devm_kmalloc(tps->dev,
+					ext_reg_irq_nb *
+					sizeof(struct tps6594_ext_regulator_irq_data),
+					GFP_KERNEL);
+	if (!irq_ext_reg_data)
+		return -ENOMEM;
+
+	for (i = 0; i < ext_reg_irq_nb; ++i) {
+		irq_type = &tps6594_ext_regulator_irq_types[i];
+
+		irq = platform_get_irq_byname(pdev, irq_type->irq_name);
+		if (irq < 0)
+			return -EINVAL;
+
+		irq_ext_reg_data[i].dev = tps->dev;
+		irq_ext_reg_data[i].type = irq_type;
+
+		error = devm_request_threaded_irq(tps->dev, irq, NULL,
+						  tps6594_regulator_irq_handler,
+						  IRQF_ONESHOT,
+						  irq_type->irq_name,
+						  &irq_ext_reg_data[i]);
+		if (error) {
+			dev_err(tps->dev, "failed to request %s IRQ %d: %d\n",
+				irq_type->irq_name, irq, error);
+			return error;
+		}
+	}
+	return 0;
+}
+
+static struct platform_driver tps6594_regulator_driver = {
+	.driver = {
+		.name = "tps6594-regulator",
+	},
+	.probe = tps6594_regulator_probe,
+};
+
+module_platform_driver(tps6594_regulator_driver);
+
+MODULE_ALIAS("platform:tps6594-regulator");
+MODULE_AUTHOR("Jerome Neanne <jneanne@baylibre.com>");
+MODULE_DESCRIPTION("TPS6594 voltage regulator driver");
+MODULE_LICENSE("GPL");
-- 
2.39.2

Re: [PATCH v3 2/3] pinctrl: tps6594: add for TPS6594 PMIC

[Linus Walleij]

Hi Esteban,

thanks for your patch!

On Fri, Apr 14, 2023 at 12:12 PM Esteban Blanc <eblanc@baylibre.com> wrote:

> TI TPS6594 PMIC has 11 GPIOs which can be used for different
> functions.
>
> This add a pinctrl and pinmux drivers in order to use those functions.
>
> Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
(...)
> +config PINCTRL_TPS6594
> +       tristate "Pinctrl and GPIO driver for TI TPS6594 PMIC"
> +       depends on MFD_TPS6594
> +       default MFD_TPS6594
> +       select PINMUX
> +       select GPIOLIB

select GPIO_REGMAP
?

I think this driver can use the GPIO_REGMAP helper library.

Please look into other drivers using this, such as
drivers/gpio/gpio-sl28cpld.c

Yours,
Linus Walleij

Re: [PATCH v3 2/3] pinctrl: tps6594: add for TPS6594 PMIC

[Esteban Blanc]

On Fri Apr 21, 2023 at 10:34 AM CEST, Linus Walleij wrote:
> Hi Esteban,
>
> thanks for your patch!
>
> On Fri, Apr 14, 2023 at 12:12 PM Esteban Blanc <eblanc@baylibre.com> wrote:
>
> > TI TPS6594 PMIC has 11 GPIOs which can be used for different
> > functions.
> >
> > This add a pinctrl and pinmux drivers in order to use those functions.
> >
> > Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
> (...)
> > +config PINCTRL_TPS6594
> > +       tristate "Pinctrl and GPIO driver for TI TPS6594 PMIC"
> > +       depends on MFD_TPS6594
> > +       default MFD_TPS6594
> > +       select PINMUX
> > +       select GPIOLIB
>
> select GPIO_REGMAP
> ?
>
> I think this driver can use the GPIO_REGMAP helper library.
>
> Please look into other drivers using this, such as
> drivers/gpio/gpio-sl28cpld.c

I had a look at this driver and gpio-regmap.c. I think I understood
what's going on, but I'm not sure how to handle the
gpio_regmap_set_direction case. It is using the same reg_mask_xlate to
determine the register and value to write as gpio_regmap_set or
gpio_regmap_read. The problem is that this PMIC has 1 register per GPIO
for the configuration (GPIOX_CONF registers with a bit for direction),
while the in and out register are used for 8 pins (GPIO_OUT_1,
GPIO_OUT_2 and GPIO_IN_1, GPIO_IN_2). This means that the register and
mask returned by reg_mask_xlate will be erroneous in one or the other
case.

I noticed that I could override reg_mask_xlate, so I should be able to
"just" match on the base address given as argument to perform a
different computation depending on whether we are using reg_mask_xlate in
a "direction change" or not, but somehow this feels a bit wrong.

Is this the correct solution?
Am I missing something?

Thanks again for your time. Best regards,

-- 
Esteban Blanc
BayLibre

Re: [PATCH v3 2/3] pinctrl: tps6594: add for TPS6594 PMIC

[Linus Walleij]

On Wed, May 3, 2023 at 1:37 PM Esteban Blanc <eblanc@baylibre.com> wrote:
> On Fri Apr 21, 2023 at 10:34 AM CEST, Linus Walleij wrote:
> > Hi Esteban,
> >
> > thanks for your patch!
> >
> > On Fri, Apr 14, 2023 at 12:12 PM Esteban Blanc <eblanc@baylibre.com> wrote:
> >
> > > TI TPS6594 PMIC has 11 GPIOs which can be used for different
> > > functions.
> > >
> > > This add a pinctrl and pinmux drivers in order to use those functions.
> > >
> > > Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
> > (...)
> > > +config PINCTRL_TPS6594
> > > +       tristate "Pinctrl and GPIO driver for TI TPS6594 PMIC"
> > > +       depends on MFD_TPS6594
> > > +       default MFD_TPS6594
> > > +       select PINMUX
> > > +       select GPIOLIB
> >
> > select GPIO_REGMAP
> > ?
> >
> > I think this driver can use the GPIO_REGMAP helper library.
> >
> > Please look into other drivers using this, such as
> > drivers/gpio/gpio-sl28cpld.c
>
> I had a look at this driver and gpio-regmap.c. I think I understood
> what's going on, but I'm not sure how to handle the
> gpio_regmap_set_direction case. It is using the same reg_mask_xlate to
> determine the register and value to write as gpio_regmap_set or
> gpio_regmap_read. The problem is that this PMIC has 1 register per GPIO
> for the configuration (GPIOX_CONF registers with a bit for direction),
> while the in and out register are used for 8 pins (GPIO_OUT_1,
> GPIO_OUT_2 and GPIO_IN_1, GPIO_IN_2). This means that the register and
> mask returned by reg_mask_xlate will be erroneous in one or the other
> case.
>
> I noticed that I could override reg_mask_xlate, so I should be able to
> "just" match on the base address given as argument to perform a
> different computation depending on whether we are using reg_mask_xlate in
> a "direction change" or not, but somehow this feels a bit wrong.
>
> Is this the correct solution?
> Am I missing something?

This is a question for Michael Walle who wrote gpio-regmap,
Michael, what do you say?

Yours,
Linus Walleij

Re: [PATCH v3 2/3] pinctrl: tps6594: add for TPS6594 PMIC

[Michael Walle]

Hi,

>> I noticed that I could override reg_mask_xlate, so I should be able to
>> "just" match on the base address given as argument to perform a
>> different computation depending on whether we are using reg_mask_xlate 
>> in
>> a "direction change" or not, but somehow this feels a bit wrong.
>> 
>> Is this the correct solution?
>> Am I missing something?

No you don't miss anything. This is the actual use case for the base
parameter. If you need your own .xlate you can match on the base address
to do the translation based on wether it is used for .direction, .set
or .get.

I.e.

switch (base) {
case REG_IO_CTRL:
    do_something_with_reg_and_mask;
case REG_DAT:
    do_something_different_with_reg_and_mask;
default:
    error;
}

-michael

Re: [PATCH v3 2/3] pinctrl: tps6594: add for TPS6594 PMIC

[Esteban Blanc]

On Fri May 5, 2023 at 1:31 PM CEST, Michael Walle wrote:
> Hi,
>
> >> I noticed that I could override reg_mask_xlate, so I should be able to
> >> "just" match on the base address given as argument to perform a
> >> different computation depending on whether we are using reg_mask_xlate 
> >> in
> >> a "direction change" or not, but somehow this feels a bit wrong.
> >> 
> >> Is this the correct solution?
> >> Am I missing something?
>
> No you don't miss anything. This is the actual use case for the base
> parameter. If you need your own .xlate you can match on the base address
> to do the translation based on wether it is used for .direction, .set
> or .get.
>
> I.e.
>
> switch (base) {
> case REG_IO_CTRL:
>     do_something_with_reg_and_mask;
> case REG_DAT:
>     do_something_different_with_reg_and_mask;
> default:
>     error;
> }

Ok perfect I will do that then!

Best regards,

-- 
Esteban Blanc
BayLibre