[RFC PATCH net-next v5 0/9] TXGBE PHYLINK support

[RFC PATCH net-next v5 0/9] TXGBE PHYLINK support

[Jiawen Wu]

Implement I2C, SFP, GPIO and PHYLINK to setup TXGBE link.

Because our I2C and PCS are based on Synopsys Designware IP-core, extend
the i2c-designware and pcs-xpcs driver to realize our functions.

v4 -> v5:
- add clock register
- delete i2c-dw.h with platform data
- introduce property "i2c-dw-flags" to match device flags
- get resource from platform info to do ioremap
- rename quirk functions in i2c-designware-*.c
- fix calling txgbe_phylink_init()

v3 -> v4:
- modify I2C transfer to be generic implementation
- avoid to read DW_IC_COMP_PARAM_1
- remove redundant "if" statement
- add specific labels to handle error in txgbe_init_phy(), and remove
  "if" conditions in txgbe_remove_phy()

v2 -> v3:
- delete own I2C bus master driver, support it in i2c-designware
- delete own PCS functions, remove pma configuration and 1000BASE-X mode
- add basic function for 10GBASE-R interface in pcs-xpcs
- add helper to get txgbe pointer from netdev

v1 -> v2:
- add comments to indicate GPIO lines
- add I2C write operation support
- modify GPIO direction functions
- rename functions related to PHY interface
- add condition on interface changing to re-config PCS
- add to set advertise and fix to get status for 1000BASE-X mode
- other redundant codes remove

Jiawen Wu (9):
  net: txgbe: Add software nodes to support phylink
  i2c: designware: Add driver support for Wangxun 10Gb NIC
  net: txgbe: Register fixed rate clock
  net: txgbe: Register I2C platform device
  net: txgbe: Add SFP module identify
  net: txgbe: Support GPIO to SFP socket
  net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS
  net: txgbe: Implement phylink pcs
  net: txgbe: Support phylink MAC layer

 drivers/i2c/busses/i2c-designware-common.c    |   8 +
 drivers/i2c/busses/i2c-designware-core.h      |   1 +
 drivers/i2c/busses/i2c-designware-master.c    |  84 ++-
 drivers/i2c/busses/i2c-designware-platdrv.c   |  20 +
 drivers/net/ethernet/wangxun/Kconfig          |   7 +
 drivers/net/ethernet/wangxun/libwx/wx_lib.c   |   3 +-
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |   3 +
 drivers/net/ethernet/wangxun/txgbe/Makefile   |   1 +
 .../ethernet/wangxun/txgbe/txgbe_ethtool.c    |  28 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  63 +-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 620 ++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_phy.h    |  10 +
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  94 +++
 drivers/net/pcs/pcs-xpcs.c                    |  56 ++
 include/linux/pcs/pcs-xpcs.h                  |   1 +
 15 files changed, 963 insertions(+), 36 deletions(-)
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h

-- 
2.27.0

[RFC PATCH net-next v5 1/9] net: txgbe: Add software nodes to support phylink

[Jiawen Wu]

Register software nodes for GPIO, I2C, SFP and PHYLINK. Define the
device properties.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |  1 +
 drivers/net/ethernet/wangxun/txgbe/Makefile   |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   | 20 ++++-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 89 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_phy.h    | 10 +++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   | 49 ++++++++++
 6 files changed, 169 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
 create mode 100644 drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h

diff --git a/drivers/net/ethernet/wangxun/libwx/wx_type.h b/drivers/net/ethernet/wangxun/libwx/wx_type.h
index 32f952d93009..97bce855bc60 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_type.h
+++ b/drivers/net/ethernet/wangxun/libwx/wx_type.h
@@ -611,6 +611,7 @@ enum wx_isb_idx {
 
 struct wx {
 	u8 __iomem *hw_addr;
+	void *priv;
 	struct pci_dev *pdev;
 	struct net_device *netdev;
 	struct wx_bus_info bus;
diff --git a/drivers/net/ethernet/wangxun/txgbe/Makefile b/drivers/net/ethernet/wangxun/txgbe/Makefile
index 6db14a2cb2d0..7507f762edfe 100644
--- a/drivers/net/ethernet/wangxun/txgbe/Makefile
+++ b/drivers/net/ethernet/wangxun/txgbe/Makefile
@@ -8,4 +8,5 @@ obj-$(CONFIG_TXGBE) += txgbe.o
 
 txgbe-objs := txgbe_main.o \
               txgbe_hw.o \
+              txgbe_phy.o \
               txgbe_ethtool.o
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index 5b8a121fb496..e6bec16a2199 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -15,6 +15,7 @@
 #include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_hw.h"
+#include "txgbe_phy.h"
 #include "txgbe_ethtool.h"
 
 char txgbe_driver_name[] = "txgbe";
@@ -513,6 +514,7 @@ static int txgbe_probe(struct pci_dev *pdev,
 	struct net_device *netdev;
 	int err, expected_gts;
 	struct wx *wx = NULL;
+	struct txgbe *txgbe;
 
 	u16 eeprom_verh = 0, eeprom_verl = 0, offset = 0;
 	u16 eeprom_cfg_blkh = 0, eeprom_cfg_blkl = 0;
@@ -663,10 +665,21 @@ static int txgbe_probe(struct pci_dev *pdev,
 			 "0x%08x", etrack_id);
 	}
 
-	err = register_netdev(netdev);
+	txgbe = devm_kzalloc(&pdev->dev, sizeof(*txgbe), GFP_KERNEL);
+	if (!txgbe)
+		goto err_release_hw;
+
+	txgbe->wx = wx;
+	wx->priv = txgbe;
+
+	err = txgbe_init_phy(txgbe);
 	if (err)
 		goto err_release_hw;
 
+	err = register_netdev(netdev);
+	if (err)
+		goto err_remove_phy;
+
 	pci_set_drvdata(pdev, wx);
 
 	netif_tx_stop_all_queues(netdev);
@@ -694,6 +707,8 @@ static int txgbe_probe(struct pci_dev *pdev,
 
 	return 0;
 
+err_remove_phy:
+	txgbe_remove_phy(txgbe);
 err_release_hw:
 	wx_clear_interrupt_scheme(wx);
 	wx_control_hw(wx, false);
@@ -719,11 +734,14 @@ static int txgbe_probe(struct pci_dev *pdev,
 static void txgbe_remove(struct pci_dev *pdev)
 {
 	struct wx *wx = pci_get_drvdata(pdev);
+	struct txgbe *txgbe = wx->priv;
 	struct net_device *netdev;
 
 	netdev = wx->netdev;
 	unregister_netdev(netdev);
 
+	txgbe_remove_phy(txgbe);
+
 	pci_release_selected_regions(pdev,
 				     pci_select_bars(pdev, IORESOURCE_MEM));
 
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
new file mode 100644
index 000000000000..8d36621b99d0
--- /dev/null
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
+
+#include <linux/gpio/property.h>
+#include <linux/i2c.h>
+#include <linux/pci.h>
+
+#include "../libwx/wx_type.h"
+#include "txgbe_type.h"
+#include "txgbe_phy.h"
+
+static int txgbe_swnodes_register(struct txgbe *txgbe)
+{
+	struct txgbe_nodes *nodes = &txgbe->nodes;
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct software_node *swnodes;
+	u32 id;
+
+	id = (pdev->bus->number << 8) | pdev->devfn;
+
+	snprintf(nodes->gpio_name, sizeof(nodes->gpio_name), "txgbe_gpio-%x", id);
+	snprintf(nodes->i2c_name, sizeof(nodes->i2c_name), "txgbe_i2c-%x", id);
+	snprintf(nodes->sfp_name, sizeof(nodes->sfp_name), "txgbe_sfp-%x", id);
+	snprintf(nodes->phylink_name, sizeof(nodes->phylink_name), "txgbe_phylink-%x", id);
+
+	swnodes = nodes->swnodes;
+
+	/* GPIO 0: tx fault
+	 * GPIO 1: tx disable
+	 * GPIO 2: sfp module absent
+	 * GPIO 3: rx signal lost
+	 * GPIO 4: rate select, 1G(0) 10G(1)
+	 * GPIO 5: rate select, 1G(0) 10G(1)
+	 */
+	nodes->gpio_props[0] = PROPERTY_ENTRY_STRING("pinctrl-names", "default");
+	swnodes[SWNODE_GPIO] = NODE_PROP(nodes->gpio_name, nodes->gpio_props);
+	nodes->gpio0_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 0, GPIO_ACTIVE_HIGH);
+	nodes->gpio1_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 1, GPIO_ACTIVE_HIGH);
+	nodes->gpio2_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 2, GPIO_ACTIVE_LOW);
+	nodes->gpio3_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 3, GPIO_ACTIVE_HIGH);
+	nodes->gpio4_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 4, GPIO_ACTIVE_HIGH);
+	nodes->gpio5_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_GPIO], 5, GPIO_ACTIVE_HIGH);
+
+	nodes->i2c_props[0] = PROPERTY_ENTRY_STRING("compatible", "snps,designware-i2c");
+	nodes->i2c_props[1] = PROPERTY_ENTRY_U32("i2c-dw-flags", 0x800);
+	nodes->i2c_props[2] = PROPERTY_ENTRY_U32("clock-frequency", I2C_MAX_STANDARD_MODE_FREQ);
+	swnodes[SWNODE_I2C] = NODE_PROP(nodes->i2c_name, nodes->i2c_props);
+	nodes->i2c_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_I2C]);
+
+	nodes->sfp_props[0] = PROPERTY_ENTRY_STRING("compatible", "sff,sfp");
+	nodes->sfp_props[1] = PROPERTY_ENTRY_REF_ARRAY("i2c-bus", nodes->i2c_ref);
+	nodes->sfp_props[2] = PROPERTY_ENTRY_REF_ARRAY("tx-fault-gpios", nodes->gpio0_ref);
+	nodes->sfp_props[3] = PROPERTY_ENTRY_REF_ARRAY("tx-disable-gpios", nodes->gpio1_ref);
+	nodes->sfp_props[4] = PROPERTY_ENTRY_REF_ARRAY("mod-def0-gpios", nodes->gpio2_ref);
+	nodes->sfp_props[5] = PROPERTY_ENTRY_REF_ARRAY("los-gpios", nodes->gpio3_ref);
+	nodes->sfp_props[6] = PROPERTY_ENTRY_REF_ARRAY("rate-select1-gpios", nodes->gpio4_ref);
+	nodes->sfp_props[7] = PROPERTY_ENTRY_REF_ARRAY("rate-select0-gpios", nodes->gpio5_ref);
+	swnodes[SWNODE_SFP] = NODE_PROP(nodes->sfp_name, nodes->sfp_props);
+	nodes->sfp_ref[0] = SOFTWARE_NODE_REFERENCE(&swnodes[SWNODE_SFP]);
+
+	nodes->phylink_props[0] = PROPERTY_ENTRY_STRING("managed", "in-band-status");
+	nodes->phylink_props[1] = PROPERTY_ENTRY_REF_ARRAY("sfp", nodes->sfp_ref);
+	swnodes[SWNODE_PHYLINK] = NODE_PROP(nodes->phylink_name, nodes->phylink_props);
+
+	nodes->group[SWNODE_GPIO] = &swnodes[SWNODE_GPIO];
+	nodes->group[SWNODE_I2C] = &swnodes[SWNODE_I2C];
+	nodes->group[SWNODE_SFP] = &swnodes[SWNODE_SFP];
+	nodes->group[SWNODE_PHYLINK] = &swnodes[SWNODE_PHYLINK];
+
+	return software_node_register_node_group(nodes->group);
+}
+
+int txgbe_init_phy(struct txgbe *txgbe)
+{
+	int ret;
+
+	ret = txgbe_swnodes_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to register software nodes\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+void txgbe_remove_phy(struct txgbe *txgbe)
+{
+	software_node_unregister_node_group(txgbe->nodes.group);
+}
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
new file mode 100644
index 000000000000..1ab592124986
--- /dev/null
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
+
+#ifndef _TXGBE_PHY_H_
+#define _TXGBE_PHY_H_
+
+int txgbe_init_phy(struct txgbe *txgbe);
+void txgbe_remove_phy(struct txgbe *txgbe);
+
+#endif /* _TXGBE_NODE_H_ */
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 63a1c733718d..5bef0f9df523 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -4,6 +4,8 @@
 #ifndef _TXGBE_TYPE_H_
 #define _TXGBE_TYPE_H_
 
+#include <linux/property.h>
+
 /* Device IDs */
 #define TXGBE_DEV_ID_SP1000                     0x1001
 #define TXGBE_DEV_ID_WX1820                     0x2001
@@ -99,4 +101,51 @@
 
 extern char txgbe_driver_name[];
 
+static inline struct txgbe *netdev_to_txgbe(struct net_device *netdev)
+{
+	struct wx *wx = netdev_priv(netdev);
+
+	return wx->priv;
+}
+
+#define NODE_PROP(_NAME, _PROP)			\
+	(const struct software_node) {		\
+		.name = _NAME,			\
+		.properties = _PROP,		\
+	}
+
+enum txgbe_swnodes {
+	SWNODE_GPIO = 0,
+	SWNODE_I2C,
+	SWNODE_SFP,
+	SWNODE_PHYLINK,
+	SWNODE_MAX
+};
+
+struct txgbe_nodes {
+	char gpio_name[32];
+	char i2c_name[32];
+	char sfp_name[32];
+	char phylink_name[32];
+	struct property_entry gpio_props[1];
+	struct property_entry i2c_props[3];
+	struct property_entry sfp_props[8];
+	struct property_entry phylink_props[2];
+	struct software_node_ref_args i2c_ref[1];
+	struct software_node_ref_args gpio0_ref[1];
+	struct software_node_ref_args gpio1_ref[1];
+	struct software_node_ref_args gpio2_ref[1];
+	struct software_node_ref_args gpio3_ref[1];
+	struct software_node_ref_args gpio4_ref[1];
+	struct software_node_ref_args gpio5_ref[1];
+	struct software_node_ref_args sfp_ref[1];
+	struct software_node swnodes[SWNODE_MAX];
+	const struct software_node *group[SWNODE_MAX + 1];
+};
+
+struct txgbe {
+	struct wx *wx;
+	struct txgbe_nodes nodes;
+};
+
 #endif /* _TXGBE_TYPE_H_ */
-- 
2.27.0

Re: [RFC PATCH net-next v5 1/9] net: txgbe: Add software nodes to support phylink

[Simon Horman]

On Wed, Apr 26, 2023 at 03:14:26PM +0800, Jiawen Wu wrote:

...

> @@ -663,10 +665,21 @@ static int txgbe_probe(struct pci_dev *pdev,
>  			 "0x%08x", etrack_id);
>  	}
>  
> -	err = register_netdev(netdev);
> +	txgbe = devm_kzalloc(&pdev->dev, sizeof(*txgbe), GFP_KERNEL);
> +	if (!txgbe)

Hi Jiawen,

I think yo need to set err here.

> +		goto err_release_hw;
> +

...

[RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
with SFP.

Introduce the property "i2c-dw-flags" to match device data for software
node case. Since IO resource was mapped on the ethernet driver, add a model
quirk to get resource from platform info.

The exists IP limitations are dealt as workarounds:
- IP does not support interrupt mode, it works on polling mode.
- Additionally set FIFO depth address the chip issue.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/i2c/busses/i2c-designware-common.c  |  8 ++
 drivers/i2c/busses/i2c-designware-core.h    |  1 +
 drivers/i2c/busses/i2c-designware-master.c  | 84 ++++++++++++++++++++-
 drivers/i2c/busses/i2c-designware-platdrv.c | 20 +++++
 4 files changed, 110 insertions(+), 3 deletions(-)

diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c
index 0dc6b1ce663f..a7c2e67ccbf6 100644
--- a/drivers/i2c/busses/i2c-designware-common.c
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -575,6 +575,14 @@ int i2c_dw_set_fifo_size(struct dw_i2c_dev *dev)
 	unsigned int param;
 	int ret;
 
+	/* DW_IC_COMP_PARAM_1 not implement for IP issue */
+	if ((dev->flags & MODEL_MASK) == MODEL_WANGXUN_SP) {
+		dev->tx_fifo_depth = 4;
+		dev->rx_fifo_depth = 0;
+
+		return 0;
+	}
+
 	/*
 	 * Try to detect the FIFO depth if not set by interface driver,
 	 * the depth could be from 2 to 256 from HW spec.
diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
index 050d8c63ad3c..c686198e12d2 100644
--- a/drivers/i2c/busses/i2c-designware-core.h
+++ b/drivers/i2c/busses/i2c-designware-core.h
@@ -303,6 +303,7 @@ struct dw_i2c_dev {
 #define MODEL_MSCC_OCELOT			BIT(8)
 #define MODEL_BAIKAL_BT1			BIT(9)
 #define MODEL_AMD_NAVI_GPU			BIT(10)
+#define MODEL_WANGXUN_SP			BIT(11)
 #define MODEL_MASK				GENMASK(11, 8)
 
 /*
diff --git a/drivers/i2c/busses/i2c-designware-master.c b/drivers/i2c/busses/i2c-designware-master.c
index 55ea91a63382..fe85c2ac79d7 100644
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -354,6 +354,68 @@ static int amd_i2c_dw_xfer_quirk(struct i2c_adapter *adap, struct i2c_msg *msgs,
 	return 0;
 }
 
+static int i2c_dw_poll_tx_empty(struct dw_i2c_dev *dev)
+{
+	u32 val;
+
+	return regmap_read_poll_timeout(dev->map, DW_IC_RAW_INTR_STAT, val,
+					val & DW_IC_INTR_TX_EMPTY,
+					100, 1000);
+}
+
+static int i2c_dw_poll_rx_full(struct dw_i2c_dev *dev)
+{
+	u32 val;
+
+	return regmap_read_poll_timeout(dev->map, DW_IC_RAW_INTR_STAT, val,
+					val & DW_IC_INTR_RX_FULL,
+					100, 1000);
+}
+
+static int txgbe_i2c_dw_xfer_quirk(struct i2c_adapter *adap, struct i2c_msg *msgs,
+				   int num_msgs)
+{
+	struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
+	int msg_idx, buf_len, data_idx, ret;
+	unsigned int val, stop = 0;
+	u8 *buf;
+
+	dev->msgs = msgs;
+	dev->msgs_num = num_msgs;
+	i2c_dw_xfer_init(dev);
+	regmap_write(dev->map, DW_IC_INTR_MASK, 0);
+
+	for (msg_idx = 0; msg_idx < num_msgs; msg_idx++) {
+		buf = msgs[msg_idx].buf;
+		buf_len = msgs[msg_idx].len;
+
+		for (data_idx = 0; data_idx < buf_len; data_idx++) {
+			if (msg_idx == num_msgs - 1 && data_idx == buf_len - 1)
+				stop |= BIT(9);
+
+			if (msgs[msg_idx].flags & I2C_M_RD) {
+				regmap_write(dev->map, DW_IC_DATA_CMD, 0x100 | stop);
+
+				ret = i2c_dw_poll_rx_full(dev);
+				if (ret)
+					return ret;
+
+				regmap_read(dev->map, DW_IC_DATA_CMD, &val);
+				buf[data_idx] = val;
+			} else {
+				ret = i2c_dw_poll_tx_empty(dev);
+				if (ret)
+					return ret;
+
+				regmap_write(dev->map, DW_IC_DATA_CMD,
+					     buf[data_idx] | stop);
+			}
+		}
+	}
+
+	return num_msgs;
+}
+
 /*
  * Initiate (and continue) low level master read/write transaction.
  * This function is only called from i2c_dw_isr, and pumping i2c_msg
@@ -568,6 +630,11 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 		goto done_nolock;
 	}
 
+	if ((dev->flags & MODEL_MASK) == MODEL_WANGXUN_SP) {
+		ret = txgbe_i2c_dw_xfer_quirk(adap, msgs, num);
+		goto done_nolock;
+	}
+
 	reinit_completion(&dev->cmd_complete);
 	dev->msgs = msgs;
 	dev->msgs_num = num;
@@ -848,7 +915,7 @@ static int i2c_dw_init_recovery_info(struct dw_i2c_dev *dev)
 	return 0;
 }
 
-static int amd_i2c_adap_quirk(struct dw_i2c_dev *dev)
+static int i2c_dw_poll_adap_quirk(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
 	int ret;
@@ -862,6 +929,17 @@ static int amd_i2c_adap_quirk(struct dw_i2c_dev *dev)
 	return ret;
 }
 
+static bool i2c_dw_is_model_poll(struct dw_i2c_dev *dev)
+{
+	switch (dev->flags & MODEL_MASK) {
+	case MODEL_AMD_NAVI_GPU:
+	case MODEL_WANGXUN_SP:
+		return true;
+	default:
+		return false;
+	}
+}
+
 int i2c_dw_probe_master(struct dw_i2c_dev *dev)
 {
 	struct i2c_adapter *adap = &dev->adapter;
@@ -917,8 +995,8 @@ int i2c_dw_probe_master(struct dw_i2c_dev *dev)
 	adap->dev.parent = dev->dev;
 	i2c_set_adapdata(adap, dev);
 
-	if ((dev->flags & MODEL_MASK) == MODEL_AMD_NAVI_GPU)
-		return amd_i2c_adap_quirk(dev);
+	if (i2c_dw_is_model_poll(dev))
+		return i2c_dw_poll_adap_quirk(dev);
 
 	if (dev->flags & ACCESS_NO_IRQ_SUSPEND) {
 		irq_flags = IRQF_NO_SUSPEND;
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 74182db03a88..5504579cd622 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -168,6 +168,20 @@ static inline int dw_i2c_of_configure(struct platform_device *pdev)
 }
 #endif
 
+static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev->dev);
+	struct resource *r;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r)
+		return -ENODEV;
+
+	dev->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
+
+	return PTR_ERR_OR_ZERO(dev->base);
+}
+
 static void dw_i2c_plat_pm_cleanup(struct dw_i2c_dev *dev)
 {
 	pm_runtime_disable(dev->dev);
@@ -185,6 +199,9 @@ static int dw_i2c_plat_request_regs(struct dw_i2c_dev *dev)
 	case MODEL_BAIKAL_BT1:
 		ret = bt1_i2c_request_regs(dev);
 		break;
+	case MODEL_WANGXUN_SP:
+		ret = txgbe_i2c_request_regs(dev);
+		break;
 	default:
 		dev->base = devm_platform_ioremap_resource(pdev, 0);
 		ret = PTR_ERR_OR_ZERO(dev->base);
@@ -278,6 +295,9 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	dev->flags = (uintptr_t)device_get_match_data(&pdev->dev);
+	if (!dev->flags)
+		device_property_read_u32(&pdev->dev, "i2c-dw-flags", &dev->flags);
+
 	dev->dev = &pdev->dev;
 	dev->irq = irq;
 	platform_set_drvdata(pdev, dev);
-- 
2.27.0

Re: [RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[andy.shevchenko]

Wed, Apr 26, 2023 at 03:14:27PM +0800, Jiawen Wu kirjoitti:
> Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
> with SFP.
> 
> Introduce the property "i2c-dw-flags" to match device data for software
> node case. Since IO resource was mapped on the ethernet driver, add a model
> quirk to get resource from platform info.
> 
> The exists IP limitations are dealt as workarounds:
> - IP does not support interrupt mode, it works on polling mode.
> - Additionally set FIFO depth address the chip issue.

Thanks for an update, my comments below.

...

>  		goto done_nolock;
>  	}
>  
> +	if ((dev->flags & MODEL_MASK) == MODEL_WANGXUN_SP) {
> +		ret = txgbe_i2c_dw_xfer_quirk(adap, msgs, num);
> +		goto done_nolock;
> +	}

	switch (dev->flags & MODEL_MASK) {
	case AMD:
		...
	case WANGXUN:
		...
	default:
		break;
	}

...

> +static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
> +{
> +	struct platform_device *pdev = to_platform_device(dev->dev);
> +	struct resource *r;
> +
> +	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!r)
> +		return -ENODEV;
> +
> +	dev->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> +
> +	return PTR_ERR_OR_ZERO(dev->base);
> +}

Redundant. See below.

...

>  	case MODEL_BAIKAL_BT1:
>  		ret = bt1_i2c_request_regs(dev);
>  		break;
> +	case MODEL_WANGXUN_SP:
> +		ret = txgbe_i2c_request_regs(dev);

How is it different to...

> +		break;
>  	default:
>  		dev->base = devm_platform_ioremap_resource(pdev, 0);

...this one?

...

>  	dev->flags = (uintptr_t)device_get_match_data(&pdev->dev);

> +	if (!dev->flags)

No need to check this. Just define priorities (I would go with above to be
higher priority).

> +		device_property_read_u32(&pdev->dev, "i2c-dw-flags", &dev->flags);

Needs to be added to the Device Tree bindings I believe.

But wait, don't we have other ways to detect your hardware at probe time and
initialize flags respectively?

-- 
With Best Regards,
Andy Shevchenko

RE: [RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

On Wednesday, April 26, 2023 11:45 PM, andy.shevchenko@gmail.com wrote:
> Wed, Apr 26, 2023 at 03:14:27PM +0800, Jiawen Wu kirjoitti:
> > Wangxun 10Gb ethernet chip is connected to Designware I2C, to communicate
> > with SFP.
> >
> > Introduce the property "i2c-dw-flags" to match device data for software
> > node case. Since IO resource was mapped on the ethernet driver, add a model
> > quirk to get resource from platform info.
> >
> > The exists IP limitations are dealt as workarounds:
> > - IP does not support interrupt mode, it works on polling mode.
> > - Additionally set FIFO depth address the chip issue.
> 
> Thanks for an update, my comments below.
> 
> ...
> 
> >  		goto done_nolock;
> >  	}
> >
> > +	if ((dev->flags & MODEL_MASK) == MODEL_WANGXUN_SP) {
> > +		ret = txgbe_i2c_dw_xfer_quirk(adap, msgs, num);
> > +		goto done_nolock;
> > +	}
> 
> 	switch (dev->flags & MODEL_MASK) {
> 	case AMD:
> 		...
> 	case WANGXUN:
> 		...
> 	default:
> 		break;
> 	}
> 
> ...
> 
> > +static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
> > +{
> > +	struct platform_device *pdev = to_platform_device(dev->dev);
> > +	struct resource *r;
> > +
> > +	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > +	if (!r)
> > +		return -ENODEV;
> > +
> > +	dev->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> > +
> > +	return PTR_ERR_OR_ZERO(dev->base);
> > +}
> 
> Redundant. See below.
> 
> ...
> 
> >  	case MODEL_BAIKAL_BT1:
> >  		ret = bt1_i2c_request_regs(dev);
> >  		break;
> > +	case MODEL_WANGXUN_SP:
> > +		ret = txgbe_i2c_request_regs(dev);
> 
> How is it different to...
> 
> > +		break;
> >  	default:
> >  		dev->base = devm_platform_ioremap_resource(pdev, 0);
> 
> ...this one?
> 

devm_platform_ioremap_resource() has one more devm_request_mem_region()
operation than devm_ioremap(). By my test, this memory cannot be re-requested,
only re-mapped.

> ...
> 
> >  	dev->flags = (uintptr_t)device_get_match_data(&pdev->dev);
> 
> > +	if (!dev->flags)
> 
> No need to check this. Just define priorities (I would go with above to be
> higher priority).
> 
> > +		device_property_read_u32(&pdev->dev, "i2c-dw-flags", &dev->flags);
> 
> Needs to be added to the Device Tree bindings I believe.
> 
> But wait, don't we have other ways to detect your hardware at probe time and
> initialize flags respectively?
> 

I2C is connected to our NIC chip with no PCI ID, so I register a platform device for it.
Please see the 4/9 patch. Software nodes are used to pass the device structure but
no DT and ACPI. I haven't found another way to initialize flags yet, other than the
platform data used in the previous patch (it seems to be an obsolete way).

> --
> With Best Regards,
> Andy Shevchenko
> 
> 
> 

Re: [RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Andy Shevchenko]

On Thu, Apr 27, 2023 at 5:15 AM Jiawen Wu <jiawenwu@trustnetic.com> wrote:
> On Wednesday, April 26, 2023 11:45 PM, andy.shevchenko@gmail.com wrote:
> > Wed, Apr 26, 2023 at 03:14:27PM +0800, Jiawen Wu kirjoitti:

...

> > > +static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
> > > +{
> > > +   struct platform_device *pdev = to_platform_device(dev->dev);
> > > +   struct resource *r;
> > > +
> > > +   r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > +   if (!r)
> > > +           return -ENODEV;
> > > +
> > > +   dev->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> > > +
> > > +   return PTR_ERR_OR_ZERO(dev->base);
> > > +}
> >
> > Redundant. See below.

...

> > >     case MODEL_BAIKAL_BT1:
> > >             ret = bt1_i2c_request_regs(dev);
> > >             break;
> > > +   case MODEL_WANGXUN_SP:
> > > +           ret = txgbe_i2c_request_regs(dev);
> >
> > How is it different to...
> >
> > > +           break;
> > >     default:
> > >             dev->base = devm_platform_ioremap_resource(pdev, 0);
> >
> > ...this one?
>
> devm_platform_ioremap_resource() has one more devm_request_mem_region()
> operation than devm_ioremap(). By my test, this memory cannot be re-requested,
> only re-mapped.

Yeah, which makes a point that the mother driver requests a region
that doesn't belong to it. You need to split that properly in the
mother driver and avoid requesting it there. Is it feasible? If not,
why?

...

> > >     dev->flags = (uintptr_t)device_get_match_data(&pdev->dev);
> >
> > > +   if (!dev->flags)
> >
> > No need to check this. Just define priorities (I would go with above to be
> > higher priority).
> >
> > > +           device_property_read_u32(&pdev->dev, "i2c-dw-flags", &dev->flags);
> >
> > Needs to be added to the Device Tree bindings I believe.
> >
> > But wait, don't we have other ways to detect your hardware at probe time and
> > initialize flags respectively?
>
> I2C is connected to our NIC chip with no PCI ID, so I register a platform device for it.
> Please see the 4/9 patch. Software nodes are used to pass the device structure but
> no DT and ACPI. I haven't found another way to initialize flags yet, other than the
> platform data used in the previous patch (it seems to be an obsolete way).

You can share a common data structure between the mother driver and
her children. In that case you may access it via
`dev_get_drvdata(pdev.dev->parent)` call.

OTOH, the property, if only Linux (kernel) specific for internal
usage, should be named accordingly, or be prepared to have one in
Device Tree / ACPI / etc. Examples: USB dwc3 driver (see "linux,"
ones), or intel-lpss-pci.c/intel-lpss-acpi.c (see the SPI type).

-- 
With Best Regards,
Andy Shevchenko

RE: [RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

On Thursday, April 27, 2023 1:57 PM, Andy Shevchenko wrote:
> On Thu, Apr 27, 2023 at 5:15 AM Jiawen Wu <jiawenwu@trustnetic.com> wrote:
> > On Wednesday, April 26, 2023 11:45 PM, andy.shevchenko@gmail.com wrote:
> > > Wed, Apr 26, 2023 at 03:14:27PM +0800, Jiawen Wu kirjoitti:
> 
> ...
> 
> > > > +static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
> > > > +{
> > > > +   struct platform_device *pdev = to_platform_device(dev->dev);
> > > > +   struct resource *r;
> > > > +
> > > > +   r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > > +   if (!r)
> > > > +           return -ENODEV;
> > > > +
> > > > +   dev->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> > > > +
> > > > +   return PTR_ERR_OR_ZERO(dev->base);
> > > > +}
> > >
> > > Redundant. See below.
> 
> ...
> 
> > > >     case MODEL_BAIKAL_BT1:
> > > >             ret = bt1_i2c_request_regs(dev);
> > > >             break;
> > > > +   case MODEL_WANGXUN_SP:
> > > > +           ret = txgbe_i2c_request_regs(dev);
> > >
> > > How is it different to...
> > >
> > > > +           break;
> > > >     default:
> > > >             dev->base = devm_platform_ioremap_resource(pdev, 0);
> > >
> > > ...this one?
> >
> > devm_platform_ioremap_resource() has one more devm_request_mem_region()
> > operation than devm_ioremap(). By my test, this memory cannot be re-requested,
> > only re-mapped.
> 
> Yeah, which makes a point that the mother driver requests a region
> that doesn't belong to it. You need to split that properly in the
> mother driver and avoid requesting it there. Is it feasible? If not,
> why?

The I2C region belongs to the middle part of the total region. It was not considered to
split because the mother driver implement I2C bus master driver itself in the previous
patch. But is it suitable for splitting? After splitting, I get two virtual address, and each
time I read/write to a register, I have to determine which region it belongs to...Right?

> 
> ...
> 
> > > >     dev->flags = (uintptr_t)device_get_match_data(&pdev->dev);
> > >
> > > > +   if (!dev->flags)
> > >
> > > No need to check this. Just define priorities (I would go with above to be
> > > higher priority).
> > >
> > > > +           device_property_read_u32(&pdev->dev, "i2c-dw-flags", &dev->flags);
> > >
> > > Needs to be added to the Device Tree bindings I believe.
> > >
> > > But wait, don't we have other ways to detect your hardware at probe time and
> > > initialize flags respectively?
> >
> > I2C is connected to our NIC chip with no PCI ID, so I register a platform device for it.
> > Please see the 4/9 patch. Software nodes are used to pass the device structure but
> > no DT and ACPI. I haven't found another way to initialize flags yet, other than the
> > platform data used in the previous patch (it seems to be an obsolete way).
> 
> You can share a common data structure between the mother driver and
> her children. In that case you may access it via
> `dev_get_drvdata(pdev.dev->parent)` call.
> 

I'd like to try it.

> OTOH, the property, if only Linux (kernel) specific for internal
> usage, should be named accordingly, or be prepared to have one in
> Device Tree / ACPI / etc. Examples: USB dwc3 driver (see "linux,"
> ones), or intel-lpss-pci.c/intel-lpss-acpi.c (see the SPI type).
> 
> --
> With Best Regards,
> Andy Shevchenko
> 

Re: [RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Andy Shevchenko]

On Thu, Apr 27, 2023 at 9:58 AM Jiawen Wu <jiawenwu@trustnetic.com> wrote:
> On Thursday, April 27, 2023 1:57 PM, Andy Shevchenko wrote:
> > On Thu, Apr 27, 2023 at 5:15 AM Jiawen Wu <jiawenwu@trustnetic.com> wrote:
> > > On Wednesday, April 26, 2023 11:45 PM, andy.shevchenko@gmail.com wrote:
> > > > Wed, Apr 26, 2023 at 03:14:27PM +0800, Jiawen Wu kirjoitti:

...

> > > > > +static int txgbe_i2c_request_regs(struct dw_i2c_dev *dev)
> > > > > +{
> > > > > +   struct platform_device *pdev = to_platform_device(dev->dev);
> > > > > +   struct resource *r;
> > > > > +
> > > > > +   r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > > > +   if (!r)
> > > > > +           return -ENODEV;
> > > > > +
> > > > > +   dev->base = devm_ioremap(&pdev->dev, r->start, resource_size(r));
> > > > > +
> > > > > +   return PTR_ERR_OR_ZERO(dev->base);
> > > > > +}
> > > >
> > > > Redundant. See below.

...

> > > > >     case MODEL_BAIKAL_BT1:
> > > > >             ret = bt1_i2c_request_regs(dev);
> > > > >             break;
> > > > > +   case MODEL_WANGXUN_SP:
> > > > > +           ret = txgbe_i2c_request_regs(dev);
> > > >
> > > > How is it different to...
> > > >
> > > > > +           break;
> > > > >     default:
> > > > >             dev->base = devm_platform_ioremap_resource(pdev, 0);
> > > >
> > > > ...this one?
> > >
> > > devm_platform_ioremap_resource() has one more devm_request_mem_region()
> > > operation than devm_ioremap(). By my test, this memory cannot be re-requested,
> > > only re-mapped.
> >
> > Yeah, which makes a point that the mother driver requests a region
> > that doesn't belong to it. You need to split that properly in the
> > mother driver and avoid requesting it there. Is it feasible? If not,
> > why?
>
> The I2C region belongs to the middle part of the total region. It was not considered to
> split because the mother driver implement I2C bus master driver itself in the previous
> patch. But is it suitable for splitting? After splitting, I get two virtual address, and each
> time I read/write to a register, I have to determine which region it belongs to...Right?

If it's in the middle there are two (maybe more, but I can't right now
come up with) possible solutions:
1/ mother driver can provide a regmap, then in the children drivers
the dev_get_regmap(pdev->dev.parent) will return it (see
intel_soc_pmic_*.c set of drivers, IIRC they work with this schema in
mind)
2/ in the mother driver you need to open code remapping resource in a
way that it does ioremap and request regions separately.

The problem with your current approach is that you request a region in
the driver which does not handle that part of IO space and belongs to
another one. It's a clear layering violation. (Note, we already have
one big driver that does something like this and we have to learn from
it not to be trapped by making the same mistake).


-- 
With Best Regards,
Andy Shevchenko

RE: [RFC PATCH net-next v5 2/9] i2c: designware: Add driver support for Wangxun 10Gb NIC

[Jiawen Wu]

> You can share a common data structure between the mother driver and
> her children. In that case you may access it via
> `dev_get_drvdata(pdev.dev->parent)` call.
> 

Unfortunately, the driver data already stores the private structure of the
adapter, so no more data can be stored.

[RFC PATCH net-next v5 3/9] net: txgbe: Register fixed rate clock

[Jiawen Wu]

In order for I2C to be able to work in standard mode, register a fixed
rate clock for each I2C device.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 41 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  2 +
 3 files changed, 44 insertions(+)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index c9d88673d306..a62614eeed2e 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -40,6 +40,7 @@ config NGBE
 config TXGBE
 	tristate "Wangxun(R) 10GbE PCI Express adapters support"
 	depends on PCI
+	select COMMON_CLK
 	select LIBWX
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 8d36621b99d0..4311d80aa5c3 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -2,6 +2,8 @@
 /* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
 
 #include <linux/gpio/property.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
 #include <linux/i2c.h>
 #include <linux/pci.h>
 
@@ -70,6 +72,32 @@ static int txgbe_swnodes_register(struct txgbe *txgbe)
 	return software_node_register_node_group(nodes->group);
 }
 
+static int txgbe_clock_register(struct txgbe *txgbe)
+{
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct clk_lookup *clock;
+	char clk_name[32];
+	struct clk *clk;
+
+	snprintf(clk_name, sizeof(clk_name), "i2c_designware.%d",
+		 (pdev->bus->number << 8) | pdev->devfn);
+
+	clk = clk_register_fixed_rate(NULL, clk_name, NULL, 0, 156250000);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	clock = clkdev_create(clk, NULL, clk_name);
+	if (!clock) {
+		clk_unregister(clk);
+		return PTR_ERR(clock);
+	}
+
+	txgbe->clk = clk;
+	txgbe->clock = clock;
+
+	return 0;
+}
+
 int txgbe_init_phy(struct txgbe *txgbe)
 {
 	int ret;
@@ -80,10 +108,23 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		return ret;
 	}
 
+	ret = txgbe_clock_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
+		goto err_unregister_swnode;
+	}
+
 	return 0;
+
+err_unregister_swnode:
+	software_node_unregister_node_group(txgbe->nodes.group);
+
+	return ret;
 }
 
 void txgbe_remove_phy(struct txgbe *txgbe)
 {
+	clkdev_drop(txgbe->clock);
+	clk_unregister(txgbe->clk);
 	software_node_unregister_node_group(txgbe->nodes.group);
 }
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 5bef0f9df523..cdbc4b37f832 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -146,6 +146,8 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct clk_lookup *clock;
+	struct clk *clk;
 };
 
 #endif /* _TXGBE_TYPE_H_ */
-- 
2.27.0

[RFC PATCH net-next v5 4/9] net: txgbe: Register I2C platform device

[Jiawen Wu]

Register the platform device to use Designware I2C bus master driver.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 40 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  4 ++
 3 files changed, 45 insertions(+)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index a62614eeed2e..8f2c52a9a30e 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -40,6 +40,7 @@ config NGBE
 config TXGBE
 	tristate "Wangxun(R) 10GbE PCI Express adapters support"
 	depends on PCI
+	select I2C_DESIGNWARE_PLATFORM
 	select COMMON_CLK
 	select LIBWX
 	help
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 4311d80aa5c3..861bfae9ee65 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 /* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
 
+#include <linux/platform_device.h>
 #include <linux/gpio/property.h>
 #include <linux/clkdev.h>
 #include <linux/clk-provider.h>
@@ -98,6 +99,35 @@ static int txgbe_clock_register(struct txgbe *txgbe)
 	return 0;
 }
 
+static int txgbe_i2c_register(struct txgbe *txgbe)
+{
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct platform_device_info info = {};
+	struct platform_device *i2c_dev;
+	struct resource res[2] = {};
+
+	info.parent = &pdev->dev;
+	info.fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_I2C]);
+	info.name = "i2c_designware";
+	info.id = (pdev->bus->number << 8) | pdev->devfn;
+
+	res[0].start = pci_resource_start(pdev, 0) + TXGBE_I2C_BASE;
+	res[0].end = pci_resource_start(pdev, 0) + TXGBE_I2C_BASE + 0x100 - 1;
+	res[0].flags = IORESOURCE_MEM;
+	res[1].start = pdev->irq;
+	res[1].end = pdev->irq;
+	res[1].flags = IORESOURCE_IRQ;
+	info.res = res;
+	info.num_res = 2;
+	i2c_dev = platform_device_register_full(&info);
+	if (IS_ERR(i2c_dev))
+		return PTR_ERR(i2c_dev);
+
+	txgbe->i2c_dev = i2c_dev;
+
+	return 0;
+}
+
 int txgbe_init_phy(struct txgbe *txgbe)
 {
 	int ret;
@@ -114,8 +144,17 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		goto err_unregister_swnode;
 	}
 
+	ret = txgbe_i2c_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init i2c interface: %d\n", ret);
+		goto err_unregister_clk;
+	}
+
 	return 0;
 
+err_unregister_clk:
+	clkdev_drop(txgbe->clock);
+	clk_unregister(txgbe->clk);
 err_unregister_swnode:
 	software_node_unregister_node_group(txgbe->nodes.group);
 
@@ -124,6 +163,7 @@ int txgbe_init_phy(struct txgbe *txgbe)
 
 void txgbe_remove_phy(struct txgbe *txgbe)
 {
+	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
 	software_node_unregister_node_group(txgbe->nodes.group);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index cdbc4b37f832..55979abf01f2 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -55,6 +55,9 @@
 #define TXGBE_TS_CTL                            0x10300
 #define TXGBE_TS_CTL_EVAL_MD                    BIT(31)
 
+/* I2C registers */
+#define TXGBE_I2C_BASE                          0x14900
+
 /* Part Number String Length */
 #define TXGBE_PBANUM_LENGTH                     32
 
@@ -146,6 +149,7 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
 	struct clk *clk;
 };
-- 
2.27.0

Re: [RFC PATCH net-next v5 4/9] net: txgbe: Register I2C platform device

[andy.shevchenko]

Wed, Apr 26, 2023 at 03:14:29PM +0800, Jiawen Wu kirjoitti:
> Register the platform device to use Designware I2C bus master driver.

...

> +static int txgbe_i2c_register(struct txgbe *txgbe)
> +{
> +	struct pci_dev *pdev = txgbe->wx->pdev;
> +	struct platform_device_info info = {};
> +	struct platform_device *i2c_dev;
> +	struct resource res[2] = {};
> +
> +	info.parent = &pdev->dev;
> +	info.fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_I2C]);
> +	info.name = "i2c_designware";
> +	info.id = (pdev->bus->number << 8) | pdev->devfn;

> +	res[0].start = pci_resource_start(pdev, 0) + TXGBE_I2C_BASE;
> +	res[0].end = pci_resource_start(pdev, 0) + TXGBE_I2C_BASE + 0x100 - 1;
> +	res[0].flags = IORESOURCE_MEM;

DEFINE_RES_MEM()

> +	res[1].start = pdev->irq;
> +	res[1].end = pdev->irq;
> +	res[1].flags = IORESOURCE_IRQ;

DEFINE_RES_IRQ()

> +	info.res = res;
> +	info.num_res = 2;

ARRAY_SIZE()

> +	i2c_dev = platform_device_register_full(&info);
> +	if (IS_ERR(i2c_dev))
> +		return PTR_ERR(i2c_dev);
> +
> +	txgbe->i2c_dev = i2c_dev;
> +
> +	return 0;
> +}

-- 
With Best Regards,
Andy Shevchenko

[RFC PATCH net-next v5 5/9] net: txgbe: Add SFP module identify

[Jiawen Wu]

Register SFP platform device to get modules information.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 28 +++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  1 +
 3 files changed, 30 insertions(+)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 8f2c52a9a30e..3fd2bb2f4535 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -43,6 +43,7 @@ config TXGBE
 	select I2C_DESIGNWARE_PLATFORM
 	select COMMON_CLK
 	select LIBWX
+	select SFP
 	help
 	  This driver supports Wangxun(R) 10GbE PCI Express family of
 	  adapters.
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 861bfae9ee65..9fd83894a3e7 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -128,6 +128,25 @@ static int txgbe_i2c_register(struct txgbe *txgbe)
 	return 0;
 }
 
+static int txgbe_sfp_register(struct txgbe *txgbe)
+{
+	struct pci_dev *pdev = txgbe->wx->pdev;
+	struct platform_device_info info = {};
+	struct platform_device *sfp_dev;
+
+	info.parent = &pdev->dev;
+	info.fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_SFP]);
+	info.name = "sfp";
+	info.id = (pdev->bus->number << 8) | pdev->devfn;
+	sfp_dev = platform_device_register_full(&info);
+	if (IS_ERR(sfp_dev))
+		return PTR_ERR(sfp_dev);
+
+	txgbe->sfp_dev = sfp_dev;
+
+	return 0;
+}
+
 int txgbe_init_phy(struct txgbe *txgbe)
 {
 	int ret;
@@ -150,8 +169,16 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		goto err_unregister_clk;
 	}
 
+	ret = txgbe_sfp_register(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to register sfp\n");
+		goto err_unregister_i2c;
+	}
+
 	return 0;
 
+err_unregister_i2c:
+	platform_device_unregister(txgbe->i2c_dev);
 err_unregister_clk:
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
@@ -163,6 +190,7 @@ int txgbe_init_phy(struct txgbe *txgbe)
 
 void txgbe_remove_phy(struct txgbe *txgbe)
 {
+	platform_device_unregister(txgbe->sfp_dev);
 	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 55979abf01f2..fc91e0fc37a6 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -149,6 +149,7 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
 	struct clk *clk;
-- 
2.27.0

[RFC PATCH net-next v5 6/9] net: txgbe: Support GPIO to SFP socket

[Jiawen Wu]

Register GPIO chip and handle GPIO IRQ for SFP socket.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |   2 +
 drivers/net/ethernet/wangxun/libwx/wx_lib.c   |   3 +-
 drivers/net/ethernet/wangxun/libwx/wx_type.h  |   2 +
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  20 +-
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 228 ++++++++++++++++++
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  27 +++
 6 files changed, 263 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 3fd2bb2f4535..9212cef53f60 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -41,6 +41,8 @@ config TXGBE
 	tristate "Wangxun(R) 10GbE PCI Express adapters support"
 	depends on PCI
 	select I2C_DESIGNWARE_PLATFORM
+	select GPIOLIB_IRQCHIP
+	select GPIOLIB
 	select COMMON_CLK
 	select LIBWX
 	select SFP
diff --git a/drivers/net/ethernet/wangxun/libwx/wx_lib.c b/drivers/net/ethernet/wangxun/libwx/wx_lib.c
index 1e8d8b7b0c62..590215303d45 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_lib.c
+++ b/drivers/net/ethernet/wangxun/libwx/wx_lib.c
@@ -1348,7 +1348,8 @@ void wx_free_irq(struct wx *wx)
 		free_irq(entry->vector, q_vector);
 	}
 
-	free_irq(wx->msix_entries[vector].vector, wx);
+	if (wx->mac.type == wx_mac_em)
+		free_irq(wx->msix_entries[vector].vector, wx);
 }
 EXPORT_SYMBOL(wx_free_irq);
 
diff --git a/drivers/net/ethernet/wangxun/libwx/wx_type.h b/drivers/net/ethernet/wangxun/libwx/wx_type.h
index 97bce855bc60..d151d6f79022 100644
--- a/drivers/net/ethernet/wangxun/libwx/wx_type.h
+++ b/drivers/net/ethernet/wangxun/libwx/wx_type.h
@@ -79,7 +79,9 @@
 #define WX_GPIO_INTMASK              0x14834
 #define WX_GPIO_INTTYPE_LEVEL        0x14838
 #define WX_GPIO_POLARITY             0x1483C
+#define WX_GPIO_INTSTATUS            0x14844
 #define WX_GPIO_EOI                  0x1484C
+#define WX_GPIO_EXT                  0x14850
 
 /*********************** Transmit DMA registers **************************/
 /* transmit global control */
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index e6bec16a2199..608fbec55427 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -82,6 +82,8 @@ static int txgbe_enumerate_functions(struct wx *wx)
  **/
 static void txgbe_irq_enable(struct wx *wx, bool queues)
 {
+	wr32(wx, WX_PX_MISC_IEN, TXGBE_PX_MISC_IEN_MASK);
+
 	/* unmask interrupt */
 	wx_intr_enable(wx, TXGBE_INTR_MISC(wx));
 	if (queues)
@@ -129,17 +131,6 @@ static irqreturn_t txgbe_intr(int __always_unused irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static irqreturn_t txgbe_msix_other(int __always_unused irq, void *data)
-{
-	struct wx *wx = data;
-
-	/* re-enable the original interrupt state */
-	if (netif_running(wx->netdev))
-		txgbe_irq_enable(wx, false);
-
-	return IRQ_HANDLED;
-}
-
 /**
  * txgbe_request_msix_irqs - Initialize MSI-X interrupts
  * @wx: board private structure
@@ -171,13 +162,6 @@ static int txgbe_request_msix_irqs(struct wx *wx)
 		}
 	}
 
-	err = request_irq(wx->msix_entries[vector].vector,
-			  txgbe_msix_other, 0, netdev->name, wx);
-	if (err) {
-		wx_err(wx, "request_irq for msix_other failed: %d\n", err);
-		goto free_queue_irqs;
-	}
-
 	return 0;
 
 free_queue_irqs:
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 9fd83894a3e7..4357f9853544 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -2,6 +2,9 @@
 /* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */
 
 #include <linux/platform_device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/machine.h>
+#include <linux/gpio/driver.h>
 #include <linux/gpio/property.h>
 #include <linux/clkdev.h>
 #include <linux/clk-provider.h>
@@ -9,6 +12,7 @@
 #include <linux/pci.h>
 
 #include "../libwx/wx_type.h"
+#include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_phy.h"
 
@@ -73,6 +77,224 @@ static int txgbe_swnodes_register(struct txgbe *txgbe)
 	return software_node_register_node_group(nodes->group);
 }
 
+static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	struct txgbe *txgbe = wx->priv;
+	int val;
+
+	val = rd32m(wx, WX_GPIO_EXT, BIT(offset));
+
+	txgbe->gpio_orig &= ~BIT(offset);
+	txgbe->gpio_orig |= val;
+
+	return !!(val & BIT(offset));
+}
+
+static int txgbe_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	u32 val;
+
+	val = rd32(wx, WX_GPIO_DDR);
+	if (BIT(offset) & val)
+		return GPIO_LINE_DIRECTION_OUT;
+
+	return GPIO_LINE_DIRECTION_IN;
+}
+
+static int txgbe_gpio_direction_in(struct gpio_chip *chip, unsigned int offset)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+
+	wr32m(wx, WX_GPIO_DDR, BIT(offset), 0);
+
+	return 0;
+}
+
+static int txgbe_gpio_direction_out(struct gpio_chip *chip, unsigned int offset,
+				    int val)
+{
+	struct wx *wx = gpiochip_get_data(chip);
+	u32 mask;
+
+	mask = BIT(offset) | BIT(offset - 1);
+	if (val)
+		wr32m(wx, WX_GPIO_DR, mask, mask);
+	else
+		wr32m(wx, WX_GPIO_DR, mask, 0);
+
+	wr32m(wx, WX_GPIO_DDR, BIT(offset), BIT(offset));
+
+	return 0;
+}
+
+static void txgbe_gpio_irq_ack(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+
+	wr32(wx, WX_GPIO_EOI, BIT(hwirq));
+}
+
+static void txgbe_gpio_irq_mask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+
+	gpiochip_disable_irq(gc, hwirq);
+
+	wr32m(wx, WX_GPIO_INTMASK, BIT(hwirq), BIT(hwirq));
+}
+
+static void txgbe_gpio_irq_unmask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+
+	gpiochip_enable_irq(gc, hwirq);
+
+	wr32m(wx, WX_GPIO_INTMASK, BIT(hwirq), 0);
+}
+
+static int txgbe_gpio_set_type(struct irq_data *d, unsigned int type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	struct wx *wx = gpiochip_get_data(gc);
+	u32 level, polarity;
+
+	level = rd32(wx, WX_GPIO_INTTYPE_LEVEL);
+	polarity = rd32(wx, WX_GPIO_POLARITY);
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_BOTH:
+		level |= BIT(hwirq);
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		level |= BIT(hwirq);
+		polarity |= BIT(hwirq);
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		level |= BIT(hwirq);
+		polarity &= ~BIT(hwirq);
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		level &= ~BIT(hwirq);
+		polarity |= BIT(hwirq);
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		level &= ~BIT(hwirq);
+		polarity &= ~BIT(hwirq);
+		break;
+	}
+
+	if (type & IRQ_TYPE_LEVEL_MASK)
+		irq_set_handler_locked(d, handle_level_irq);
+	else if (type & IRQ_TYPE_EDGE_BOTH)
+		irq_set_handler_locked(d, handle_edge_irq);
+
+	wr32m(wx, WX_GPIO_INTEN, BIT(hwirq), BIT(hwirq));
+	wr32(wx, WX_GPIO_INTTYPE_LEVEL, level);
+	if (type != IRQ_TYPE_EDGE_BOTH)
+		wr32(wx, WX_GPIO_POLARITY, polarity);
+
+	return 0;
+}
+
+static const struct irq_chip txgbe_gpio_irq_chip = {
+	.name = "txgbe_gpio_irq",
+	.irq_ack = txgbe_gpio_irq_ack,
+	.irq_mask = txgbe_gpio_irq_mask,
+	.irq_unmask = txgbe_gpio_irq_unmask,
+	.irq_set_type = txgbe_gpio_set_type,
+	.flags = IRQCHIP_IMMUTABLE,
+	GPIOCHIP_IRQ_RESOURCE_HELPERS,
+};
+
+static void txgbe_irq_handler(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct wx *wx = irq_desc_get_handler_data(desc);
+	struct txgbe *txgbe = wx->priv;
+	irq_hw_number_t hwirq;
+	unsigned long gpioirq;
+	struct gpio_chip *gc;
+	u32 gpio;
+
+	chained_irq_enter(chip, desc);
+
+	gpioirq = rd32(wx, WX_GPIO_INTSTATUS);
+
+	/* workaround for hysteretic gpio interrupts */
+	gpio = rd32(wx, WX_GPIO_EXT);
+	if (!gpioirq)
+		gpioirq = txgbe->gpio_orig ^ gpio;
+
+	gc = txgbe->gpio;
+	for_each_set_bit(hwirq, &gpioirq, gc->ngpio)
+		generic_handle_domain_irq(gc->irq.domain, hwirq);
+
+	chained_irq_exit(chip, desc);
+
+	/* unmask interrupt */
+	if (netif_running(wx->netdev))
+		wx_intr_enable(wx, TXGBE_INTR_MISC(wx));
+}
+
+static int txgbe_gpio_init(struct txgbe *txgbe)
+{
+	struct gpio_irq_chip *girq;
+	struct wx *wx = txgbe->wx;
+	struct pci_dev *pdev;
+	struct gpio_chip *gc;
+	int ret;
+
+	pdev = wx->pdev;
+	txgbe->gpio_orig = 0;
+
+	gc = devm_kzalloc(&pdev->dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
+	gc->label = devm_kasprintf(&pdev->dev, GFP_KERNEL, "txgbe_gpio-%x",
+				   (pdev->bus->number << 8) | pdev->devfn);
+	gc->base = -1;
+	gc->ngpio = 6;
+	gc->owner = THIS_MODULE;
+	gc->parent = &pdev->dev;
+	gc->fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_GPIO]);
+	gc->get = txgbe_gpio_get;
+	gc->get_direction = txgbe_gpio_get_direction;
+	gc->direction_input = txgbe_gpio_direction_in;
+	gc->direction_output = txgbe_gpio_direction_out;
+	gc->can_sleep = false;
+
+	girq = &gc->irq;
+	gpio_irq_chip_set_chip(girq, &txgbe_gpio_irq_chip);
+	girq->parent_handler = txgbe_irq_handler;
+	girq->parent_handler_data = wx;
+	girq->num_parents = 1;
+	girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents),
+				     GFP_KERNEL);
+	if (!girq->parents)
+		return -ENOMEM;
+	girq->parents[0] = wx->msix_entries[wx->num_q_vectors].vector;
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_bad_irq;
+
+	ret = devm_gpiochip_add_data(&pdev->dev, gc, wx);
+	if (ret)
+		return ret;
+
+	txgbe->gpio = gc;
+
+	return 0;
+}
+
 static int txgbe_clock_register(struct txgbe *txgbe)
 {
 	struct pci_dev *pdev = txgbe->wx->pdev;
@@ -157,6 +379,12 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		return ret;
 	}
 
+	ret = txgbe_gpio_init(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init gpio\n");
+		goto err_unregister_swnode;
+	}
+
 	ret = txgbe_clock_register(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index fc91e0fc37a6..796f33fe3016 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -55,6 +55,31 @@
 #define TXGBE_TS_CTL                            0x10300
 #define TXGBE_TS_CTL_EVAL_MD                    BIT(31)
 
+/* GPIO register bit */
+#define TXGBE_GPIOBIT_0                         BIT(0) /* I:tx fault */
+#define TXGBE_GPIOBIT_1                         BIT(1) /* O:tx disabled */
+#define TXGBE_GPIOBIT_2                         BIT(2) /* I:sfp module absent */
+#define TXGBE_GPIOBIT_3                         BIT(3) /* I:rx signal lost */
+#define TXGBE_GPIOBIT_4                         BIT(4) /* O:rate select, 1G(0) 10G(1) */
+#define TXGBE_GPIOBIT_5                         BIT(5) /* O:rate select, 1G(0) 10G(1) */
+
+/* Extended Interrupt Enable Set */
+#define TXGBE_PX_MISC_ETH_LKDN                  BIT(8)
+#define TXGBE_PX_MISC_DEV_RST                   BIT(10)
+#define TXGBE_PX_MISC_ETH_EVENT                 BIT(17)
+#define TXGBE_PX_MISC_ETH_LK                    BIT(18)
+#define TXGBE_PX_MISC_ETH_AN                    BIT(19)
+#define TXGBE_PX_MISC_INT_ERR                   BIT(20)
+#define TXGBE_PX_MISC_GPIO                      BIT(26)
+#define TXGBE_PX_MISC_IEN_MASK ( \
+				TXGBE_PX_MISC_ETH_LKDN | \
+				TXGBE_PX_MISC_DEV_RST | \
+				TXGBE_PX_MISC_ETH_EVENT | \
+				TXGBE_PX_MISC_ETH_LK | \
+				TXGBE_PX_MISC_ETH_AN | \
+				TXGBE_PX_MISC_INT_ERR | \
+				TXGBE_PX_MISC_GPIO)
+
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
@@ -153,6 +178,8 @@ struct txgbe {
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
 	struct clk *clk;
+	struct gpio_chip *gpio;
+	u32 gpio_orig;
 };
 
 #endif /* _TXGBE_TYPE_H_ */
-- 
2.27.0

[RFC PATCH net-next v5 7/9] net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS

[Jiawen Wu]

Add basic support for XPCS using 10GBASE-R interface. This mode will
be extended to use interrupt, so set pcs.poll false. And avoid soft
reset so that the device using this mode is in the default configuration.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/pcs/pcs-xpcs.c   | 56 ++++++++++++++++++++++++++++++++++++
 include/linux/pcs/pcs-xpcs.h |  1 +
 2 files changed, 57 insertions(+)

diff --git a/drivers/net/pcs/pcs-xpcs.c b/drivers/net/pcs/pcs-xpcs.c
index 539cd43eae8d..9ddaceda1fe9 100644
--- a/drivers/net/pcs/pcs-xpcs.c
+++ b/drivers/net/pcs/pcs-xpcs.c
@@ -64,6 +64,16 @@ static const int xpcs_xlgmii_features[] = {
 	__ETHTOOL_LINK_MODE_MASK_NBITS,
 };
 
+static const int xpcs_10gbaser_features[] = {
+	ETHTOOL_LINK_MODE_Pause_BIT,
+	ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+	ETHTOOL_LINK_MODE_10000baseSR_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseLR_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseER_Full_BIT,
+	__ETHTOOL_LINK_MODE_MASK_NBITS,
+};
+
 static const int xpcs_sgmii_features[] = {
 	ETHTOOL_LINK_MODE_Pause_BIT,
 	ETHTOOL_LINK_MODE_Asym_Pause_BIT,
@@ -106,6 +116,10 @@ static const phy_interface_t xpcs_xlgmii_interfaces[] = {
 	PHY_INTERFACE_MODE_XLGMII,
 };
 
+static const phy_interface_t xpcs_10gbaser_interfaces[] = {
+	PHY_INTERFACE_MODE_10GBASER,
+};
+
 static const phy_interface_t xpcs_sgmii_interfaces[] = {
 	PHY_INTERFACE_MODE_SGMII,
 };
@@ -123,6 +137,7 @@ enum {
 	DW_XPCS_USXGMII,
 	DW_XPCS_10GKR,
 	DW_XPCS_XLGMII,
+	DW_XPCS_10GBASER,
 	DW_XPCS_SGMII,
 	DW_XPCS_1000BASEX,
 	DW_XPCS_2500BASEX,
@@ -246,6 +261,7 @@ static int xpcs_soft_reset(struct dw_xpcs *xpcs,
 
 	switch (compat->an_mode) {
 	case DW_AN_C73:
+	case DW_10GBASER:
 		dev = MDIO_MMD_PCS;
 		break;
 	case DW_AN_C37_SGMII:
@@ -872,6 +888,8 @@ int xpcs_do_config(struct dw_xpcs *xpcs, phy_interface_t interface,
 		return -ENODEV;
 
 	switch (compat->an_mode) {
+	case DW_10GBASER:
+		break;
 	case DW_AN_C73:
 		if (phylink_autoneg_inband(mode)) {
 			ret = xpcs_config_aneg_c73(xpcs, compat);
@@ -919,6 +937,27 @@ static int xpcs_config(struct phylink_pcs *pcs, unsigned int mode,
 	return xpcs_do_config(xpcs, interface, mode, advertising);
 }
 
+static int xpcs_get_state_10gbaser(struct dw_xpcs *xpcs,
+				   struct phylink_link_state *state)
+{
+	int ret;
+
+	state->link = false;
+
+	ret = xpcs_read(xpcs, MDIO_MMD_PCS, MDIO_STAT1);
+	if (ret < 0)
+		return ret;
+
+	if (ret & MDIO_STAT1_LSTATUS) {
+		state->link = true;
+		state->pause = MLO_PAUSE_TX | MLO_PAUSE_RX;
+		state->duplex = DUPLEX_FULL;
+		state->speed = SPEED_10000;
+	}
+
+	return 0;
+}
+
 static int xpcs_get_state_c73(struct dw_xpcs *xpcs,
 			      struct phylink_link_state *state,
 			      const struct xpcs_compat *compat)
@@ -1033,6 +1072,14 @@ static void xpcs_get_state(struct phylink_pcs *pcs,
 		return;
 
 	switch (compat->an_mode) {
+	case DW_10GBASER:
+		ret = xpcs_get_state_10gbaser(xpcs, state);
+		if (ret) {
+			pr_err("xpcs_get_state_10gbaser returned %pe\n",
+			       ERR_PTR(ret));
+			return;
+		}
+		break;
 	case DW_AN_C73:
 		ret = xpcs_get_state_c73(xpcs, state, compat);
 		if (ret) {
@@ -1188,6 +1235,12 @@ static const struct xpcs_compat synopsys_xpcs_compat[DW_XPCS_INTERFACE_MAX] = {
 		.num_interfaces = ARRAY_SIZE(xpcs_xlgmii_interfaces),
 		.an_mode = DW_AN_C73,
 	},
+	[DW_XPCS_10GBASER] = {
+		.supported = xpcs_10gbaser_features,
+		.interface = xpcs_10gbaser_interfaces,
+		.num_interfaces = ARRAY_SIZE(xpcs_10gbaser_interfaces),
+		.an_mode = DW_10GBASER,
+	},
 	[DW_XPCS_SGMII] = {
 		.supported = xpcs_sgmii_features,
 		.interface = xpcs_sgmii_interfaces,
@@ -1290,6 +1343,9 @@ struct dw_xpcs *xpcs_create(struct mdio_device *mdiodev,
 		}
 
 		xpcs->pcs.ops = &xpcs_phylink_ops;
+		if (compat->an_mode == DW_10GBASER)
+			return xpcs;
+
 		xpcs->pcs.poll = true;
 
 		ret = xpcs_soft_reset(xpcs, compat);
diff --git a/include/linux/pcs/pcs-xpcs.h b/include/linux/pcs/pcs-xpcs.h
index d2da1e0b4a92..61df0c717a0e 100644
--- a/include/linux/pcs/pcs-xpcs.h
+++ b/include/linux/pcs/pcs-xpcs.h
@@ -18,6 +18,7 @@
 #define DW_AN_C37_SGMII			2
 #define DW_2500BASEX			3
 #define DW_AN_C37_1000BASEX		4
+#define DW_10GBASER			5
 
 struct xpcs_id;
 
-- 
2.27.0

Re: [RFC PATCH net-next v5 7/9] net: pcs: Add 10GBASE-R mode for Synopsys Designware XPCS

[Russell King (Oracle)]

On Wed, Apr 26, 2023 at 03:14:32PM +0800, Jiawen Wu wrote:
> Add basic support for XPCS using 10GBASE-R interface. This mode will
> be extended to use interrupt, so set pcs.poll false. And avoid soft
> reset so that the device using this mode is in the default configuration.
> 
> Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>

See my comments on v4.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

[RFC PATCH net-next v5 8/9] net: txgbe: Implement phylink pcs

[Jiawen Wu]

Register MDIO bus for PCS layer to use Synopsys designware XPCS, support
10GBASE-R interface to the controller.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |  1 +
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 91 ++++++++++++++++++-
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |  6 ++
 3 files changed, 96 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 9212cef53f60..24338b754221 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -44,6 +44,7 @@ config TXGBE
 	select GPIOLIB_IRQCHIP
 	select GPIOLIB
 	select COMMON_CLK
+	select PCS_XPCS
 	select LIBWX
 	select SFP
 	help
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 4357f9853544..39fe09e3a82c 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -8,6 +8,8 @@
 #include <linux/gpio/property.h>
 #include <linux/clkdev.h>
 #include <linux/clk-provider.h>
+#include <linux/pcs/pcs-xpcs.h>
+#include <linux/mdio.h>
 #include <linux/i2c.h>
 #include <linux/pci.h>
 
@@ -77,6 +79,82 @@ static int txgbe_swnodes_register(struct txgbe *txgbe)
 	return software_node_register_node_group(nodes->group);
 }
 
+static int txgbe_pcs_read(struct mii_bus *bus, int addr, int devnum, int regnum)
+{
+	struct wx *wx  = bus->priv;
+	u32 offset, val;
+
+	offset = devnum << 16 | regnum;
+
+	/* Set the LAN port indicator to IDA_ADDR */
+	wr32(wx, TXGBE_XPCS_IDA_ADDR, offset);
+
+	/* Read the data from IDA_DATA register */
+	val = rd32(wx, TXGBE_XPCS_IDA_DATA);
+
+	return (u16)val;
+}
+
+static int txgbe_pcs_write(struct mii_bus *bus, int addr, int devnum, int regnum, u16 val)
+{
+	struct wx *wx = bus->priv;
+	u32 offset;
+
+	offset = devnum << 16 | regnum;
+
+	/* Set the LAN port indicator to IDA_ADDR */
+	wr32(wx, TXGBE_XPCS_IDA_ADDR, offset);
+
+	/* Write the data to IDA_DATA register */
+	wr32(wx, TXGBE_XPCS_IDA_DATA, val);
+
+	return 0;
+}
+
+static int txgbe_mdio_pcs_init(struct txgbe *txgbe)
+{
+	struct mdio_device *mdiodev;
+	struct wx *wx = txgbe->wx;
+	struct mii_bus *mii_bus;
+	struct dw_xpcs *xpcs;
+	struct pci_dev *pdev;
+	int ret = 0;
+
+	pdev = wx->pdev;
+
+	mii_bus = devm_mdiobus_alloc(&pdev->dev);
+	if (!mii_bus)
+		return -ENOMEM;
+
+	mii_bus->name = "txgbe_pcs_mdio_bus";
+	mii_bus->read_c45 = &txgbe_pcs_read;
+	mii_bus->write_c45 = &txgbe_pcs_write;
+	mii_bus->parent = &pdev->dev;
+	mii_bus->phy_mask = ~0;
+	mii_bus->priv = wx;
+	snprintf(mii_bus->id, MII_BUS_ID_SIZE, "txgbe_pcs-%x",
+		 (pdev->bus->number << 8) | pdev->devfn);
+
+	ret = devm_mdiobus_register(&pdev->dev, mii_bus);
+	if (ret)
+		return ret;
+
+	mdiodev = mdio_device_create(mii_bus, 0);
+	if (IS_ERR(mdiodev))
+		return PTR_ERR(mdiodev);
+
+	xpcs = xpcs_create(mdiodev, PHY_INTERFACE_MODE_10GBASER);
+	if (IS_ERR_OR_NULL(xpcs)) {
+		mdio_device_free(mdiodev);
+		return PTR_ERR(xpcs);
+	}
+
+	txgbe->mdiodev = mdiodev;
+	txgbe->xpcs = xpcs;
+
+	return 0;
+}
+
 static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
 	struct wx *wx = gpiochip_get_data(chip);
@@ -379,16 +457,22 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		return ret;
 	}
 
+	ret = txgbe_mdio_pcs_init(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init mdio pcs: %d\n", ret);
+		goto err_unregister_swnode;
+	}
+
 	ret = txgbe_gpio_init(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to init gpio\n");
-		goto err_unregister_swnode;
+		goto err_destroy_xpcs;
 	}
 
 	ret = txgbe_clock_register(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
-		goto err_unregister_swnode;
+		goto err_destroy_xpcs;
 	}
 
 	ret = txgbe_i2c_register(txgbe);
@@ -410,6 +494,8 @@ int txgbe_init_phy(struct txgbe *txgbe)
 err_unregister_clk:
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+err_destroy_xpcs:
+	xpcs_destroy(txgbe->xpcs);
 err_unregister_swnode:
 	software_node_unregister_node_group(txgbe->nodes.group);
 
@@ -422,5 +508,6 @@ void txgbe_remove_phy(struct txgbe *txgbe)
 	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+	xpcs_destroy(txgbe->xpcs);
 	software_node_unregister_node_group(txgbe->nodes.group);
 }
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 796f33fe3016..75b9c7ae3c21 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -83,6 +83,10 @@
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
+/************************************** ETH PHY ******************************/
+#define TXGBE_XPCS_IDA_ADDR                     0x13000
+#define TXGBE_XPCS_IDA_DATA                     0x13004
+
 /* Part Number String Length */
 #define TXGBE_PBANUM_LENGTH                     32
 
@@ -174,6 +178,8 @@ struct txgbe_nodes {
 struct txgbe {
 	struct wx *wx;
 	struct txgbe_nodes nodes;
+	struct mdio_device *mdiodev;
+	struct dw_xpcs *xpcs;
 	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
-- 
2.27.0

[RFC PATCH net-next v5 9/9] net: txgbe: Support phylink MAC layer

[Jiawen Wu]

Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
interface.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
---
 drivers/net/ethernet/wangxun/Kconfig          |   1 +
 .../ethernet/wangxun/txgbe/txgbe_ethtool.c    |  28 +++++
 .../net/ethernet/wangxun/txgbe/txgbe_main.c   |  23 ++--
 .../net/ethernet/wangxun/txgbe/txgbe_phy.c    | 113 +++++++++++++++++-
 .../net/ethernet/wangxun/txgbe/txgbe_type.h   |   5 +
 5 files changed, 154 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ethernet/wangxun/Kconfig b/drivers/net/ethernet/wangxun/Kconfig
index 24338b754221..c11ce10435cc 100644
--- a/drivers/net/ethernet/wangxun/Kconfig
+++ b/drivers/net/ethernet/wangxun/Kconfig
@@ -45,6 +45,7 @@ config TXGBE
 	select GPIOLIB
 	select COMMON_CLK
 	select PCS_XPCS
+	select PHYLINK
 	select LIBWX
 	select SFP
 	help
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
index d914e9a05404..859da112586a 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c
@@ -6,11 +6,39 @@
 #include <linux/netdevice.h>
 
 #include "../libwx/wx_ethtool.h"
+#include "../libwx/wx_type.h"
+#include "txgbe_type.h"
 #include "txgbe_ethtool.h"
 
+static int txgbe_nway_reset(struct net_device *netdev)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_nway_reset(txgbe->phylink);
+}
+
+static int txgbe_get_link_ksettings(struct net_device *netdev,
+				    struct ethtool_link_ksettings *cmd)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_ksettings_get(txgbe->phylink, cmd);
+}
+
+static int txgbe_set_link_ksettings(struct net_device *netdev,
+				    const struct ethtool_link_ksettings *cmd)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
+	return phylink_ethtool_ksettings_set(txgbe->phylink, cmd);
+}
+
 static const struct ethtool_ops txgbe_ethtool_ops = {
 	.get_drvinfo		= wx_get_drvinfo,
+	.nway_reset		= txgbe_nway_reset,
 	.get_link		= ethtool_op_get_link,
+	.get_link_ksettings	= txgbe_get_link_ksettings,
+	.set_link_ksettings	= txgbe_set_link_ksettings,
 };
 
 void txgbe_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
index 608fbec55427..ef54adb865bd 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c
@@ -7,6 +7,7 @@
 #include <linux/netdevice.h>
 #include <linux/string.h>
 #include <linux/etherdevice.h>
+#include <linux/phylink.h>
 #include <net/ip.h>
 #include <linux/if_vlan.h>
 
@@ -204,7 +205,8 @@ static int txgbe_request_irq(struct wx *wx)
 
 static void txgbe_up_complete(struct wx *wx)
 {
-	u32 reg;
+	struct net_device *netdev = wx->netdev;
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
 
 	wx_control_hw(wx, true);
 	wx_configure_vectors(wx);
@@ -213,24 +215,16 @@ static void txgbe_up_complete(struct wx *wx)
 	smp_mb__before_atomic();
 	wx_napi_enable_all(wx);
 
+	phylink_start(txgbe->phylink);
+
 	/* clear any pending interrupts, may auto mask */
 	rd32(wx, WX_PX_IC(0));
 	rd32(wx, WX_PX_IC(1));
 	rd32(wx, WX_PX_MISC_IC);
 	txgbe_irq_enable(wx, true);
 
-	/* Configure MAC Rx and Tx when link is up */
-	reg = rd32(wx, WX_MAC_RX_CFG);
-	wr32(wx, WX_MAC_RX_CFG, reg);
-	wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR);
-	reg = rd32(wx, WX_MAC_WDG_TIMEOUT);
-	wr32(wx, WX_MAC_WDG_TIMEOUT, reg);
-	reg = rd32(wx, WX_MAC_TX_CFG);
-	wr32(wx, WX_MAC_TX_CFG, (reg & ~WX_MAC_TX_CFG_SPEED_MASK) | WX_MAC_TX_CFG_SPEED_10G);
-
 	/* enable transmits */
-	netif_tx_start_all_queues(wx->netdev);
-	netif_carrier_on(wx->netdev);
+	netif_tx_start_all_queues(netdev);
 }
 
 static void txgbe_reset(struct wx *wx)
@@ -264,7 +258,6 @@ static void txgbe_disable_device(struct wx *wx)
 		wx_disable_rx_queue(wx, wx->rx_ring[i]);
 
 	netif_tx_stop_all_queues(netdev);
-	netif_carrier_off(netdev);
 	netif_tx_disable(netdev);
 
 	wx_irq_disable(wx);
@@ -295,8 +288,12 @@ static void txgbe_disable_device(struct wx *wx)
 
 static void txgbe_down(struct wx *wx)
 {
+	struct net_device *netdev = wx->netdev;
+	struct txgbe *txgbe = netdev_to_txgbe(netdev);
+
 	txgbe_disable_device(wx);
 	txgbe_reset(wx);
+	phylink_stop(txgbe->phylink);
 
 	wx_clean_all_tx_rings(wx);
 	wx_clean_all_rx_rings(wx);
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
index 39fe09e3a82c..b10edefccec8 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
@@ -9,11 +9,13 @@
 #include <linux/clkdev.h>
 #include <linux/clk-provider.h>
 #include <linux/pcs/pcs-xpcs.h>
+#include <linux/phylink.h>
 #include <linux/mdio.h>
 #include <linux/i2c.h>
 #include <linux/pci.h>
 
 #include "../libwx/wx_type.h"
+#include "../libwx/wx_lib.h"
 #include "../libwx/wx_hw.h"
 #include "txgbe_type.h"
 #include "txgbe_phy.h"
@@ -155,6 +157,95 @@ static int txgbe_mdio_pcs_init(struct txgbe *txgbe)
 	return 0;
 }
 
+static struct phylink_pcs *txgbe_phylink_mac_select(struct phylink_config *config,
+						    phy_interface_t interface)
+{
+	struct txgbe *txgbe = netdev_to_txgbe(to_net_dev(config->dev));
+
+	return &txgbe->xpcs->pcs;
+}
+
+static void txgbe_mac_config(struct phylink_config *config, unsigned int mode,
+			     const struct phylink_link_state *state)
+{
+}
+
+static void txgbe_mac_link_down(struct phylink_config *config,
+				unsigned int mode, phy_interface_t interface)
+{
+	struct wx *wx = netdev_priv(to_net_dev(config->dev));
+
+	wr32m(wx, WX_MAC_TX_CFG, WX_MAC_TX_CFG_TE, 0);
+}
+
+static void txgbe_mac_link_up(struct phylink_config *config,
+			      struct phy_device *phy,
+			      unsigned int mode, phy_interface_t interface,
+			      int speed, int duplex,
+			      bool tx_pause, bool rx_pause)
+{
+	struct wx *wx = netdev_priv(to_net_dev(config->dev));
+	u32 txcfg, wdg;
+
+	txcfg = rd32(wx, WX_MAC_TX_CFG);
+	txcfg &= ~WX_MAC_TX_CFG_SPEED_MASK;
+
+	switch (speed) {
+	case SPEED_10000:
+		txcfg |= WX_MAC_TX_CFG_SPEED_10G;
+		break;
+	case SPEED_1000:
+	case SPEED_100:
+	case SPEED_10:
+		txcfg |= WX_MAC_TX_CFG_SPEED_1G;
+		break;
+	default:
+		break;
+	}
+
+	wr32(wx, WX_MAC_TX_CFG, txcfg | WX_MAC_TX_CFG_TE);
+
+	/* Re configure MAC Rx */
+	wr32m(wx, WX_MAC_RX_CFG, WX_MAC_RX_CFG_RE, WX_MAC_RX_CFG_RE);
+	wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR);
+	wdg = rd32(wx, WX_MAC_WDG_TIMEOUT);
+	wr32(wx, WX_MAC_WDG_TIMEOUT, wdg);
+}
+
+static const struct phylink_mac_ops txgbe_mac_ops = {
+	.mac_select_pcs = txgbe_phylink_mac_select,
+	.mac_config = txgbe_mac_config,
+	.mac_link_down = txgbe_mac_link_down,
+	.mac_link_up = txgbe_mac_link_up,
+};
+
+static int txgbe_phylink_init(struct txgbe *txgbe)
+{
+	struct phylink_config *config;
+	struct fwnode_handle *fwnode;
+	struct wx *wx = txgbe->wx;
+	phy_interface_t phy_mode;
+	struct phylink *phylink;
+
+	config = devm_kzalloc(&wx->pdev->dev, sizeof(*config), GFP_KERNEL);
+	if (!config)
+		return -ENOMEM;
+
+	config->dev = &wx->netdev->dev;
+	config->type = PHYLINK_NETDEV;
+	config->mac_capabilities = MAC_10000FD | MAC_1000FD | MAC_SYM_PAUSE | MAC_ASYM_PAUSE;
+	phy_mode = PHY_INTERFACE_MODE_10GBASER;
+	__set_bit(PHY_INTERFACE_MODE_10GBASER, config->supported_interfaces);
+	fwnode = software_node_fwnode(txgbe->nodes.group[SWNODE_PHYLINK]);
+	phylink = phylink_create(config, fwnode, phy_mode, &txgbe_mac_ops);
+	if (IS_ERR(phylink))
+		return PTR_ERR(phylink);
+
+	txgbe->phylink = phylink;
+
+	return 0;
+}
+
 static int txgbe_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
 	struct wx *wx = gpiochip_get_data(chip);
@@ -301,7 +392,9 @@ static void txgbe_irq_handler(struct irq_desc *desc)
 	irq_hw_number_t hwirq;
 	unsigned long gpioirq;
 	struct gpio_chip *gc;
-	u32 gpio;
+	u32 gpio, eicr, reg;
+
+	eicr = wx_misc_isb(wx, WX_ISB_MISC);
 
 	chained_irq_enter(chip, desc);
 
@@ -318,6 +411,11 @@ static void txgbe_irq_handler(struct irq_desc *desc)
 
 	chained_irq_exit(chip, desc);
 
+	if (eicr & (TXGBE_PX_MISC_ETH_LK | TXGBE_PX_MISC_ETH_LKDN)) {
+		reg = rd32(wx, TXGBE_CFG_PORT_ST);
+		phylink_mac_change(txgbe->phylink, !!(reg & TXGBE_CFG_PORT_ST_LINK_UP));
+	}
+
 	/* unmask interrupt */
 	if (netif_running(wx->netdev))
 		wx_intr_enable(wx, TXGBE_INTR_MISC(wx));
@@ -463,16 +561,22 @@ int txgbe_init_phy(struct txgbe *txgbe)
 		goto err_unregister_swnode;
 	}
 
+	ret = txgbe_phylink_init(txgbe);
+	if (ret) {
+		wx_err(txgbe->wx, "failed to init phylink\n");
+		goto err_destroy_xpcs;
+	}
+
 	ret = txgbe_gpio_init(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to init gpio\n");
-		goto err_destroy_xpcs;
+		goto err_destroy_phylink;
 	}
 
 	ret = txgbe_clock_register(txgbe);
 	if (ret) {
 		wx_err(txgbe->wx, "failed to register clock: %d\n", ret);
-		goto err_destroy_xpcs;
+		goto err_destroy_phylink;
 	}
 
 	ret = txgbe_i2c_register(txgbe);
@@ -494,6 +598,8 @@ int txgbe_init_phy(struct txgbe *txgbe)
 err_unregister_clk:
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+err_destroy_phylink:
+	phylink_destroy(txgbe->phylink);
 err_destroy_xpcs:
 	xpcs_destroy(txgbe->xpcs);
 err_unregister_swnode:
@@ -508,6 +614,7 @@ void txgbe_remove_phy(struct txgbe *txgbe)
 	platform_device_unregister(txgbe->i2c_dev);
 	clkdev_drop(txgbe->clock);
 	clk_unregister(txgbe->clk);
+	phylink_destroy(txgbe->phylink);
 	xpcs_destroy(txgbe->xpcs);
 	software_node_unregister_node_group(txgbe->nodes.group);
 }
diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
index 75b9c7ae3c21..a889f340b14d 100644
--- a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
+++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h
@@ -80,6 +80,10 @@
 				TXGBE_PX_MISC_INT_ERR | \
 				TXGBE_PX_MISC_GPIO)
 
+/* Port cfg registers */
+#define TXGBE_CFG_PORT_ST                       0x14404
+#define TXGBE_CFG_PORT_ST_LINK_UP               BIT(0)
+
 /* I2C registers */
 #define TXGBE_I2C_BASE                          0x14900
 
@@ -180,6 +184,7 @@ struct txgbe {
 	struct txgbe_nodes nodes;
 	struct mdio_device *mdiodev;
 	struct dw_xpcs *xpcs;
+	struct phylink *phylink;
 	struct platform_device *sfp_dev;
 	struct platform_device *i2c_dev;
 	struct clk_lookup *clock;
-- 
2.27.0