From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
To: Jonathan Santos <Jonathan.Santos@analog.com>
Cc: linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
nuno.sa@analog.com, Michael.Hennerich@analog.com,
marcelo.schmitt@analog.com, jic23@kernel.org, robh@kernel.org,
krzk+dt@kernel.org, conor+dt@kernel.org,
marcelo.schmitt1@gmail.com, linus.walleij@linaro.org,
brgl@bgdev.pl, lgirdwood@gmail.com, broonie@kernel.org,
jonath4nns@gmail.com, dlechner@baylibre.com,
Pop Paul <paul.pop@analog.com>
Subject: Re: [PATCH v10 11/12] iio: adc: ad7768-1: add filter type and oversampling ratio attributes
Date: Thu, 5 Jun 2025 09:21:54 +0300 [thread overview]
Message-ID: <aEE3gsbbOuBdI1ky@smile.fi.intel.com> (raw)
In-Reply-To: <c36d6494453050041a585c0e79d7bb674da11c99.1749063024.git.Jonathan.Santos@analog.com>
On Wed, Jun 04, 2025 at 04:37:36PM -0300, Jonathan Santos wrote:
> Separate filter type and decimation rate from the sampling frequency
> attribute. The new filter type attribute enables sinc3, sinc3+rej60
> and wideband filters, which were previously unavailable.
>
> Previously, combining decimation and MCLK divider in the sampling
> frequency obscured performance trade-offs. Lower MCLK divider
> settings increase power usage, while lower decimation rates reduce
> precision by decreasing averaging. By creating an oversampling
> attribute, which controls the decimation, users gain finer control
> over performance.
>
> The addition of those attributes allows a wider range of sampling
> frequencies and more access to the device features. Sampling frequency
> table is updated after every digital filter parameter change.
>
> Changes in the sampling frequency are not allowed anymore while in
> buffered mode.
...
> +static const int ad7768_dec_rate_values[8] = {
> + 8, 16, 32, 64, 128, 256, 512, 1024,
> +};
> +
> +/* Decimation rate range for sinc3 filter */
> +static const int ad7768_sinc3_dec_rate_range[3] = {
> + 32, 32, 163840
Also leave trailing comma here.
> +};
...
> +static const char * const ad7768_filter_enum[] = {
> + [AD7768_FILTER_SINC5] = "sinc5",
> + [AD7768_FILTER_SINC3] = "sinc3",
> + [AD7768_FILTER_WIDEBAND] = "wideband",
> + [AD7768_FILTER_SINC3_REJ60] = "sinc3+rej60"
Ditto.
> };
...
> +static int ad7768_set_mclk_div(struct ad7768_state *st, unsigned int mclk_div)
> +{
> + unsigned int mclk_div_value;
> +
> + mclk_div_value = AD7768_PWR_MCLK_DIV(mclk_div);
> + /*
> + * Set power mode based on mclk_div value.
> + * ECO_MODE is only recommended for MCLK_DIV 16
'= 16.' ?
> + */
> + mclk_div_value |= mclk_div > AD7768_MCLK_DIV_16 ?
> + AD7768_PWR_PWRMODE(AD7768_FAST_MODE) :
> + AD7768_PWR_PWRMODE(AD7768_ECO_MODE);
> +
> + return regmap_update_bits(st->regmap, AD7768_REG_POWER_CLOCK,
> + AD7768_PWR_MCLK_DIV_MSK | AD7768_PWR_PWRMODE_MSK,
> + mclk_div_value);
> }
--
With Best Regards,
Andy Shevchenko
next prev parent reply other threads:[~2025-06-05 6:22 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-06-04 19:35 [PATCH v10 00/12] iio: adc: ad7768-1: Add features, improvements, and fixes Jonathan Santos
2025-06-04 19:35 ` [PATCH v10 01/12] iio: adc: ad7768-1: Ensure SYNC_IN pulse minimum timing requirement Jonathan Santos
2025-06-04 20:14 ` David Lechner
2025-06-07 12:22 ` Jonathan Cameron
2025-06-04 19:35 ` [PATCH v10 02/12] dt-bindings: trigger-source: add generic GPIO trigger source Jonathan Santos
2025-06-04 19:35 ` [PATCH v10 03/12] dt-bindings: iio: adc: ad7768-1: add trigger-sources property Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 04/12] dt-bindings: iio: adc: ad7768-1: Document GPIO controller Jonathan Santos
2025-06-07 12:28 ` Jonathan Cameron
2025-06-04 19:36 ` [PATCH v10 05/12] dt-bindings: iio: adc: ad7768-1: document regulator provider property Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 06/12] iio: adc: ad7768-1: add regulator to control VCM output Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 07/12] iio: adc: ad7768-1: Add GPIO controller support Jonathan Santos
2025-06-05 6:04 ` Andy Shevchenko
2025-06-06 19:37 ` Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 08/12] iio: adc: ad7768-1: add multiple scan types to support 16-bits mode Jonathan Santos
2025-06-05 6:06 ` Andy Shevchenko
2025-06-04 19:37 ` [PATCH v10 09/12] iio: adc: ad7768-1: add support for Synchronization over SPI Jonathan Santos
2025-06-05 6:10 ` Andy Shevchenko
2025-06-07 12:20 ` Jonathan Cameron
2025-06-04 19:37 ` [PATCH v10 10/12] iio: adc: ad7768-1: replace manual attribute declaration Jonathan Santos
2025-06-04 19:37 ` [PATCH v10 11/12] iio: adc: ad7768-1: add filter type and oversampling ratio attributes Jonathan Santos
2025-06-05 6:21 ` Andy Shevchenko [this message]
2025-06-04 19:37 ` [PATCH v10 12/12] iio: adc: ad7768-1: add low pass -3dB cutoff attribute Jonathan Santos
2025-06-05 6:14 ` Andy Shevchenko
2025-06-05 6:23 ` [PATCH v10 00/12] iio: adc: ad7768-1: Add features, improvements, and fixes Andy Shevchenko
2025-06-07 12:34 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aEE3gsbbOuBdI1ky@smile.fi.intel.com \
--to=andriy.shevchenko@linux.intel.com \
--cc=Jonathan.Santos@analog.com \
--cc=Michael.Hennerich@analog.com \
--cc=brgl@bgdev.pl \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=jic23@kernel.org \
--cc=jonath4nns@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marcelo.schmitt1@gmail.com \
--cc=marcelo.schmitt@analog.com \
--cc=nuno.sa@analog.com \
--cc=paul.pop@analog.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).