[PATCH v8 0/9] Add minimal MT8365 and MT8365-EVK support

[PATCH v8 0/9] Add minimal MT8365 and MT8365-EVK support

[Bernhard Rosenkränzer]

v8:
  - Add binding descriptions for mediatek,mt8365-systimer and
    mediatek,mt8365-uart
  - Specify ranges with parameters for u3phy

v7:
  - Update GIC information in mt8365.dtsi (thanks to Marc Zyngier for
    pointing out the problem)
  - Adjust the timer to match the updated GIC information

v6:
  - Add systimer in mt8365.dtsi
  - Add I/D caches and L2 cache details in mt8365.dtsi
  - Move bl31_secmon_reserved from mt8365.dtsi to mt8365-evk.dts
  - Fix inconsistent indentation in mt8365-pinctrl example
  - Further mt8365.dtsi cleanups
  - Submit to additional maintainers spotted by get_maintainer.pl

v5:
  - Reorder top-level entries in mediatek,mt8365-pinctrl.yaml to match
    example-schema
  - Use consistent quotes

v4:
  - Remove pins-are-numbered references that have been holding things up
    now that the patches removing it from dt-bindings have landed in linux-next

v3:
  - Remove a number of components that are not yet supported (they will
    come back alongside the corresponding drivers)
  - Address issues found by dt_binding_check (mostly fixing pinctrl
    bindings)
  - Address issues pointed out in comments
  - Reorder patches

v2:
  - Add missing dt-bindings documentation
  - Small cleanups addressing issues in v1 pointed out by Krzysztof Kozlowski


Bernhard Rosenkränzer (6):
  dt-bindings: arm64: dts: mediatek: Add mt8365-evk board
  dt-bindings: irq: mtk, sysirq: add support for mt8365
  dt-bindings: mfd: syscon: Add mt8365-syscfg
  dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC
  dt-bindings: timer: mediatek,mtk-timer: add MT8365 SoC bindings
  dt-bindings: serial: mediatek,uart: add MT8365 SoC bindings

Fabien Parent (3):
  dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
  dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
  arm64: dts: mediatek: Initial mt8365-evk support

 .../devicetree/bindings/arm/mediatek.yaml     |   4 +
 .../interrupt-controller/mediatek,sysirq.txt  |   1 +
 .../devicetree/bindings/mfd/syscon.yaml       |   1 +
 .../pinctrl/mediatek,mt8365-pinctrl.yaml      | 197 +++++++++
 .../bindings/serial/mediatek,uart.yaml        |   1 +
 .../bindings/timer/mediatek,mtk-timer.txt     |   1 +
 .../bindings/usb/mediatek,mtk-xhci.yaml       |   1 +
 .../bindings/usb/mediatek,mtu3.yaml           |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   1 +
 arch/arm64/boot/dts/mediatek/mt8365-evk.dts   | 169 ++++++++
 arch/arm64/boot/dts/mediatek/mt8365.dtsi      | 378 ++++++++++++++++++
 11 files changed, 755 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi

-- 
2.39.1

[PATCH v8 1/9] dt-bindings: arm64: dts: mediatek: Add mt8365-evk board

[Bernhard Rosenkränzer]

Add bindings for the Mediatek mt8365-evk board.

Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 Documentation/devicetree/bindings/arm/mediatek.yaml | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index 2275e5d93721b..ae12b1cab9fbd 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -244,6 +244,10 @@ properties:
           - enum:
               - mediatek,mt8183-pumpkin
           - const: mediatek,mt8183
+      - items:
+          - enum:
+              - mediatek,mt8365-evk
+          - const: mediatek,mt8365
       - items:
           - enum:
               - mediatek,mt8516-pumpkin
-- 
2.39.1

[PATCH v8 2/9] dt-bindings: irq: mtk, sysirq: add support for mt8365

[Bernhard Rosenkränzer]

Add binding documentation of mediatek,sysirq for mt8365 SoC.

Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 .../devicetree/bindings/interrupt-controller/mediatek,sysirq.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index 84ced3f4179b9..3ffc60184e445 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -25,6 +25,7 @@ Required properties:
 	"mediatek,mt6577-sysirq": for MT6577
 	"mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712
 	"mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701
+	"mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq": for MT8365
 - interrupt-controller : Identifies the node as an interrupt controller
 - #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
 - reg: Physical base address of the intpol registers and length of memory
-- 
2.39.1

[PATCH v8 3/9] dt-bindings: mfd: syscon: Add mt8365-syscfg

[Bernhard Rosenkränzer]

Document Mediatek mt8365-syscfg

Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

---
 Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
index 1b01bd0104316..7beeb0abc4db0 100644
--- a/Documentation/devicetree/bindings/mfd/syscon.yaml
+++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -50,6 +50,7 @@ properties:
               - marvell,armada-3700-usb2-host-misc
               - mediatek,mt8135-pctl-a-syscfg
               - mediatek,mt8135-pctl-b-syscfg
+              - mediatek,mt8365-syscfg
               - microchip,lan966x-cpu-syscon
               - microchip,sparx5-cpu-syscon
               - mstar,msc313-pmsleep
-- 
2.39.1

Re: [PATCH v8 3/9] dt-bindings: mfd: syscon: Add mt8365-syscfg

[Lee Jones]

On Mon, 23 Jan 2023, Bernhard Rosenkränzer wrote:

> Document Mediatek mt8365-syscfg
> 
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> 
> ---
>  Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
>  1 file changed, 1 insertion(+)

Applied, thanks

-- 
Lee Jones [李琼斯]

[PATCH v8 4/9] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC

[Bernhard Rosenkränzer]

Add devicetree bindings for Mediatek MT8365 pinctrl driver.

Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../pinctrl/mediatek,mt8365-pinctrl.yaml      | 197 ++++++++++++++++++
 1 file changed, 197 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
new file mode 100644
index 0000000000000..4b96884a1afc7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml
@@ -0,0 +1,197 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8365-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT8365 Pin Controller
+
+maintainers:
+  - Zhiyong Tao <zhiyong.tao@mediatek.com>
+  - Bernhard Rosenkränzer <bero@baylibre.com>
+
+description: |
+  The MediaTek's MT8365 Pin controller is used to control SoC pins.
+
+properties:
+  compatible:
+    const: mediatek,mt8365-pinctrl
+
+  reg:
+    maxItems: 1
+
+  mediatek,pctl-regmap:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      maxItems: 1
+    minItems: 1
+    maxItems: 2
+    description: |
+      Should be phandles of the syscfg node.
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      Number of cells in GPIO specifier. Since the generic GPIO
+      binding is used, the amount of cells must be specified as 2. See the below
+      mentioned gpio binding representation for description of particular cells.
+
+  interrupt-controller: true
+
+  interrupts:
+    maxItems: 1
+
+  "#interrupt-cells":
+    const: 2
+
+patternProperties:
+  "-pins$":
+    type: object
+    additionalProperties: false
+    patternProperties:
+      "pins$":
+        type: object
+        additionalProperties: false
+        description: |
+          A pinctrl node should contain at least one subnode representing the
+          pinctrl groups available on the machine. Each subnode will list the
+          pins it needs, and how they should be configured, with regard to muxer
+          configuration, pullups, drive strength, input enable/disable and input
+          schmitt.
+        $ref: /schemas/pinctrl/pincfg-node.yaml
+
+        properties:
+          pinmux:
+            description:
+              integer array, represents gpio pin number and mux setting.
+              Supported pin number and mux varies for different SoCs, and are
+              defined as macros in <soc>-pinfunc.h directly.
+
+          bias-disable: true
+
+          bias-pull-up:
+            description: |
+              Besides generic pinconfig options, it can be used as the pull up
+              settings for 2 pull resistors, R0 and R1. User can configure those
+              special pins.
+
+          bias-pull-down: true
+
+          input-enable: true
+
+          input-disable: true
+
+          output-low: true
+
+          output-high: true
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+          mediatek,drive-strength-adv:
+            description: |
+              Describe the specific driving setup property.
+              For I2C pins, the existing generic driving setup can only support
+              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
+              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
+              driving setup, the existing generic setup will be disabled.
+              The specific driving setup is controlled by E1E0EN.
+              When E1=0/E0=0, the strength is 0.125mA.
+              When E1=0/E0=1, the strength is 0.25mA.
+              When E1=1/E0=0, the strength is 0.5mA.
+              When E1=1/E0=1, the strength is 1mA.
+              EN is used to enable or disable the specific driving setup.
+              Valid arguments are described as below:
+              0: (E1, E0, EN) = (0, 0, 0)
+              1: (E1, E0, EN) = (0, 0, 1)
+              2: (E1, E0, EN) = (0, 1, 0)
+              3: (E1, E0, EN) = (0, 1, 1)
+              4: (E1, E0, EN) = (1, 0, 0)
+              5: (E1, E0, EN) = (1, 0, 1)
+              6: (E1, E0, EN) = (1, 1, 0)
+              7: (E1, E0, EN) = (1, 1, 1)
+              So the valid arguments are from 0 to 7.
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+          mediatek,pull-up-adv:
+            description: |
+              Pull up setings for 2 pull resistors, R0 and R1. User can
+              configure those special pins. Valid arguments are described as below:
+              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [0, 1, 2, 3]
+
+          mediatek,pull-down-adv:
+            description: |
+              Pull down settings for 2 pull resistors, R0 and R1. User can
+              configure those special pins. Valid arguments are described as below:
+              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
+              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
+              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
+              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
+            $ref: /schemas/types.yaml#/definitions/uint32
+            enum: [0, 1, 2, 3]
+
+          mediatek,tdsel:
+            description: |
+              An integer describing the steps for output level shifter duty
+              cycle when asserted (high pulse width adjustment). Valid arguments
+              are from 0 to 15.
+            $ref: /schemas/types.yaml#/definitions/uint32
+
+          mediatek,rdsel:
+            description: |
+              An integer describing the steps for input level shifter duty cycle
+              when asserted (high pulse width adjustment). Valid arguments are
+              from 0 to 63.
+            $ref: /schemas/types.yaml#/definitions/uint32
+
+        required:
+          - pinmux
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - "#gpio-cells"
+
+allOf:
+  - $ref: pinctrl.yaml#
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      pio: pinctrl@1000b000 {
+        compatible = "mediatek,mt8365-pinctrl";
+        reg = <0 0x1000b000 0 0x1000>;
+        mediatek,pctl-regmap = <&syscfg_pctl>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+
+        pio-pins {
+          pins {
+            pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
+            mediatek,pull-up-adv = <3>;
+            mediatek,drive-strength-adv = <00>;
+            bias-pull-up;
+          };
+        };
+      };
+    };
-- 
2.39.1

[PATCH v8 5/9] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings

[Bernhard Rosenkränzer]

From: Fabien Parent <fparent@baylibre.com>

Add binding documentation for the MT8365 SoC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
index 7168110e2f9de..d2655173e108c 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml
@@ -28,6 +28,7 @@ properties:
           - mediatek,mt8188-mtu3
           - mediatek,mt8192-mtu3
           - mediatek,mt8195-mtu3
+          - mediatek,mt8365-mtu3
       - const: mediatek,mtu3
 
   reg:
-- 
2.39.1

[PATCH v8 6/9] dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings

[Bernhard Rosenkränzer]

From: Fabien Parent <fparent@baylibre.com>

Add binding documentation for the MT8365 SoC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Cleanups suggested by reviewers]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index a3c37944c6305..c119caa9ad168 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -35,6 +35,7 @@ properties:
           - mediatek,mt8188-xhci
           - mediatek,mt8192-xhci
           - mediatek,mt8195-xhci
+          - mediatek,mt8365-xhci
       - const: mediatek,mtk-xhci
 
   reg:
-- 
2.39.1

[PATCH v8 7/9] dt-bindings: timer: mediatek,mtk-timer: add MT8365 SoC bindings

[Bernhard Rosenkränzer]

Add binding description for mediatek,mt8365-systimer

Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
---
 Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
index 8bbb6e94508b2..b3e797e8aa313 100644
--- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
+++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt
@@ -33,6 +33,7 @@ Required properties:
 
 	For those SoCs that use CPUX
 	* "mediatek,mt6795-systimer" for MT6795 compatible timers (CPUX)
+	* "mediatek,mt8365-systimer" for MT8365 compatible timers (CPUX)
 
 - reg: Should contain location and length for timer register.
 - clocks: Should contain system clock.
-- 
2.39.1

Re: [PATCH v8 7/9] dt-bindings: timer: mediatek,mtk-timer: add MT8365 SoC bindings

[Krzysztof Kozlowski]

On 23/01/2023 17:38, Bernhard Rosenkränzer wrote:
> Add binding description for mediatek,mt8365-systimer
> 
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> ---
>  Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt 


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

[PATCH v8 8/9] dt-bindings: serial: mediatek,uart: add MT8365 SoC bindings

[Bernhard Rosenkränzer]

Add binding description for mediatek,mt8365-uart

Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
---
 Documentation/devicetree/bindings/serial/mediatek,uart.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/serial/mediatek,uart.yaml b/Documentation/devicetree/bindings/serial/mediatek,uart.yaml
index fe098d98af6ee..303d02ca4e1ba 100644
--- a/Documentation/devicetree/bindings/serial/mediatek,uart.yaml
+++ b/Documentation/devicetree/bindings/serial/mediatek,uart.yaml
@@ -45,6 +45,7 @@ properties:
               - mediatek,mt8188-uart
               - mediatek,mt8192-uart
               - mediatek,mt8195-uart
+              - mediatek,mt8365-uart
               - mediatek,mt8516-uart
           - const: mediatek,mt6577-uart
 
-- 
2.39.1

Re: [PATCH v8 8/9] dt-bindings: serial: mediatek,uart: add MT8365 SoC bindings

[Krzysztof Kozlowski]

On 23/01/2023 17:38, Bernhard Rosenkränzer wrote:
> Add binding description for mediatek,mt8365-uart

Subject: drop second/last, redundant "bindings". The "dt-bindings"
prefix is already stating that these are bindings.

> 
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> ---


Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v8 8/9] dt-bindings: serial: mediatek,uart: add MT8365 SoC bindings

[AngeloGioacchino Del Regno]

Il 23/01/23 17:38, Bernhard Rosenkränzer ha scritto:
> Add binding description for mediatek,mt8365-uart
> 
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

[PATCH v8 9/9] arm64: dts: mediatek: Initial mt8365-evk support

[Bernhard Rosenkränzer]

From: Fabien Parent <fparent@baylibre.com>

This adds minimal support for the Mediatek 8365 SOC and the EVK reference
board, allowing the board to boot to initramfs with serial port I/O.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
---
 arch/arm64/boot/dts/mediatek/Makefile       |   1 +
 arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
 arch/arm64/boot/dts/mediatek/mt8365.dtsi    | 378 ++++++++++++++++++++
 3 files changed, 548 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 813e735c5b96d..d78523c5a7dd6 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -47,4 +47,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
new file mode 100644
index 0000000000000..275ea3a0e7085
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2021-2022 BayLibre, SAS.
+ * Authors:
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8365-pinfunc.h>
+#include "mt8365.dtsi"
+
+/ {
+	model = "MediaTek MT8365 Open Platform EVK";
+	compatible = "mediatek,mt8365-evk", "mediatek,mt8365";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
+
+		key-volume-up {
+			gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0xc0000000>;
+	};
+
+	usb_otg_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 128 KiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_reserved: secmon@43000000 {
+			no-map;
+			reg = <0 0x43000000 0 0x20000>;
+		};
+
+		/* 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+	};
+};
+
+&pio {
+	gpio_keys: gpio-keys-pins {
+		pins {
+			pinmux = <MT8365_PIN_24_KPCOL0__FUNC_KPCOL0>;
+			bias-pull-up;
+			input-enable;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins {
+			pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
+				 <MT8365_PIN_36_UTXD0__FUNC_UTXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins {
+			pinmux = <MT8365_PIN_37_URXD1__FUNC_URXD1>,
+				 <MT8365_PIN_38_UTXD1__FUNC_UTXD1>;
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		pins {
+			pinmux = <MT8365_PIN_39_URXD2__FUNC_URXD2>,
+				 <MT8365_PIN_40_UTXD2__FUNC_UTXD2>;
+		};
+	};
+
+	usb_pins: usb-pins {
+		pins-id {
+			pinmux = <MT8365_PIN_17_GPIO17__FUNC_GPIO17>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-usb0-vbus {
+			pinmux = <MT8365_PIN_16_GPIO16__FUNC_USB_DRVVBUS>;
+			output-high;
+		};
+
+		pin-usb1-vbus {
+			pinmux = <MT8365_PIN_18_GPIO18__FUNC_GPIO18>;
+			output-high;
+		};
+	};
+
+	pwm_pins: pwm-pins {
+		pins {
+			pinmux = <MT8365_PIN_19_DISP_PWM__FUNC_PWM_A>,
+				 <MT8365_PIN_116_I2S_BCK__FUNC_PWM_C>;
+		};
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
new file mode 100644
index 0000000000000..04c666cab506a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * (C) 2018 MediaTek Inc.
+ * Copyright (C) 2022 BayLibre SAS
+ * Fabien Parent <fparent@baylibre.com>
+ * Bernhard Rosenkränzer <bero@baylibre.com>
+ */
+#include <dt-bindings/clock/mediatek,mt8365-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "mediatek,mt8365";
+	interrupt-parent = <&sysirq>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+		};
+	};
+
+	clk26m: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		gic: interrupt-controller@c000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x0c000000 0 0x10000>, /* GICD */
+			      <0 0x0c080000 0 0x80000>, /* GICR */
+			      <0 0x0c400000 0 0x2000>,  /* GICC */
+			      <0 0x0c410000 0 0x1000>,  /* GICH */
+			      <0 0x0c420000 0 0x2000>;  /* GICV */
+
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		topckgen: syscon@10000000 {
+			compatible = "mediatek,mt8365-topckgen", "syscon";
+			reg = <0 0x10000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		infracfg: syscon@10001000 {
+			compatible = "mediatek,mt8365-infracfg", "syscon";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pericfg: syscon@10003000 {
+			compatible = "mediatek,mt8365-pericfg", "syscon";
+			reg = <0 0x10003000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		syscfg_pctl: syscfg-pctl@10005000 {
+			compatible = "mediatek,mt8365-syscfg", "syscon";
+			reg = <0 0x10005000 0 0x1000>;
+		};
+
+		pio: pinctrl@1000b000 {
+			compatible = "mediatek,mt8365-pinctrl";
+			reg = <0 0x1000b000 0 0x1000>;
+			mediatek,pctl-regmap = <&syscfg_pctl>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		apmixedsys: syscon@1000c000 {
+			compatible = "mediatek,mt8365-apmixedsys", "syscon";
+			reg = <0 0x1000c000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		keypad: keypad@10010000 {
+			compatible = "mediatek,mt6779-keypad";
+			reg = <0 0x10010000 0 0x1000>;
+			wakeup-source;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clk26m>;
+			clock-names = "kpd";
+			status = "disabled";
+		};
+
+		mcucfg: syscon@10200000 {
+			compatible = "mediatek,mt8365-mcucfg", "syscon";
+			reg = <0 0x10200000 0 0x2000>;
+			#clock-cells = <1>;
+		};
+
+		sysirq: interrupt-controller@10200a80 {
+			compatible = "mediatek,mt8365-sysirq", "mediatek,mt6577-sysirq";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			reg = <0 0x10200a80 0 0x20>;
+		};
+
+		infracfg_nao: infracfg@1020e000 {
+			compatible = "mediatek,mt8365-infracfg", "syscon";
+			reg = <0 0x1020e000 0 0x1000>;
+		};
+
+		rng: rng@1020f000 {
+			compatible = "mediatek,mt8365-rng", "mediatek,mt7623-rng";
+			reg = <0 0x1020f000 0 0x100>;
+			clocks = <&infracfg CLK_IFR_TRNG>;
+			clock-names = "rng";
+		};
+
+		apdma: dma-controller@11000280 {
+			compatible = "mediatek,mt8365-uart-dma", "mediatek,mt6577-uart-dma";
+			reg = <0 0x11000280 0 0x80>,
+			      <0 0x11000300 0 0x80>,
+			      <0 0x11000380 0 0x80>,
+			      <0 0x11000400 0 0x80>,
+			      <0 0x11000580 0 0x80>,
+			      <0 0x11000600 0 0x80>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+			dma-requests = <6>;
+			clocks = <&infracfg CLK_IFR_AP_DMA>;
+			clock-names = "apdma";
+			#dma-cells = <1>;
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 0>, <&apdma 1>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 2>, <&apdma 3>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt8365-uart", "mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x1000>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>;
+			clock-names = "baud", "bus";
+			dmas = <&apdma 4>, <&apdma 5>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		pwm: pwm@11006000 {
+			compatible = "mediatek,mt8365-pwm";
+			reg = <0 0x11006000 0 0x1000>;
+			#pwm-cells = <2>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&infracfg CLK_IFR_PWM_HCLK>,
+				 <&infracfg CLK_IFR_PWM>,
+				 <&infracfg CLK_IFR_PWM1>,
+				 <&infracfg CLK_IFR_PWM2>,
+				 <&infracfg CLK_IFR_PWM3>;
+			clock-names = "top", "main", "pwm1", "pwm2", "pwm3";
+		};
+
+		spi: spi@1100a000 {
+			compatible = "mediatek,mt8365-spi", "mediatek,mt7622-spi";
+			reg = <0 0x1100a000 0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_IFR_SPI0>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		ssusb: usb@11201000 {
+			compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3";
+			reg = <0 0x11201000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+				 <&infracfg CLK_IFR_SSUSB_REF>,
+				 <&infracfg CLK_IFR_SSUSB_SYS>,
+				 <&infracfg CLK_IFR_ICUSB>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			usb_host: usb@11200000 {
+				compatible = "mediatek,mt8365-xhci", "mediatek,mtk-xhci";
+				reg = <0 0x11200000 0 0x1000>;
+				reg-names = "mac";
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>;
+				clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+					 <&infracfg CLK_IFR_SSUSB_REF>,
+					 <&infracfg CLK_IFR_SSUSB_SYS>,
+					 <&infracfg CLK_IFR_ICUSB>,
+					 <&infracfg CLK_IFR_SSUSB_XHCI>;
+				clock-names = "sys_ck", "ref_ck", "mcu_ck",
+					      "dma_ck", "xhci_ck";
+				status = "disabled";
+			};
+		};
+
+		u3phy: phy@11cc0000 {
+			compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			#phy-cells = <1>;
+			ranges = <0 0 0x11cc0000 0x9000>;
+
+			u2port0: usb-phy@11cc0000 {
+				reg = <0 0x11cc0000 0 0x400>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+					 <&topckgen CLK_TOP_USB20_48M_EN>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@11cc1000 {
+				reg = <0 0x11cc1000 0 0x400>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>,
+					 <&topckgen CLK_TOP_USB20_48M_EN>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	system_clk: dummy13m {
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+		#clock-cells = <0>;
+	};
+
+	systimer: timer@10017000 {
+		compatible = "mediatek,mt8365-systimer", "mediatek,mt6795-systimer";
+		reg = <0 0x10017000 0 0x10>;
+		interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&system_clk>;
+		clock-names = "clk13m";
+	};
+};
-- 
2.39.1

Re: [PATCH v8 9/9] arm64: dts: mediatek: Initial mt8365-evk support

[AngeloGioacchino Del Regno]

Il 23/01/23 17:38, Bernhard Rosenkränzer ha scritto:
> From: Fabien Parent <fparent@baylibre.com>
> 
> This adds minimal support for the Mediatek 8365 SOC and the EVK reference
> board, allowing the board to boot to initramfs with serial port I/O.
> 
> Signed-off-by: Fabien Parent <fparent@baylibre.com>
> [bero@baylibre.com: Removed parts depending on drivers that aren't upstream yet, cleanups, add CPU cache layout, add systimer, fix GIC]
> Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
> ---
>   arch/arm64/boot/dts/mediatek/Makefile       |   1 +
>   arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 169 +++++++++
>   arch/arm64/boot/dts/mediatek/mt8365.dtsi    | 378 ++++++++++++++++++++
>   3 files changed, 548 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
>   create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
> 

..snip..

> diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> new file mode 100644
> index 0000000000000..04c666cab506a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> @@ -0,0 +1,378 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * (C) 2018 MediaTek Inc.
> + * Copyright (C) 2022 BayLibre SAS
> + * Fabien Parent <fparent@baylibre.com>
> + * Bernhard Rosenkränzer <bero@baylibre.com>
> + */
> +#include <dt-bindings/clock/mediatek,mt8365-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/thermal/thermal.h>

thermal.h is unused... please remove it for now and add it back in a commit
where you add the thermal node.

Otherwise,

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v8 0/9] Add minimal MT8365 and MT8365-EVK support

[Kevin Hilman]

Bernhard Rosenkränzer <bero@baylibre.com> writes:

> v8:
>   - Add binding descriptions for mediatek,mt8365-systimer and
>     mediatek,mt8365-uart
>   - Specify ranges with parameters for u3phy

Built this series on top of v6.2-rc1 and boot tested on mt8365-evk board
locally.

Tested-by: Kevin Hilman <khilman@baylibre.com>

Kevin