From: Jonathan Santos <Jonathan.Santos@analog.com>
To: <linux-iio@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-gpio@vger.kernel.org>
Cc: Sergiu Cuciurean <sergiu.cuciurean@analog.com>, <andy@kernel.org>,
<nuno.sa@analog.com>, <Michael.Hennerich@analog.com>,
<marcelo.schmitt@analog.com>, <jic23@kernel.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<marcelo.schmitt1@gmail.com>, <linus.walleij@linaro.org>,
<brgl@bgdev.pl>, <lgirdwood@gmail.com>, <broonie@kernel.org>,
<jonath4nns@gmail.com>, <dlechner@baylibre.com>,
Bartosz Golaszewski <bartosz.golaszewski@linaro.org>,
Jonathan Santos <Jonathan.Santos@analog.com>
Subject: [PATCH v10 07/12] iio: adc: ad7768-1: Add GPIO controller support
Date: Wed, 4 Jun 2025 16:36:43 -0300 [thread overview]
Message-ID: <eb48ea5f11503729b15a36ef00c89de3dd37bcc3.1749063024.git.Jonathan.Santos@analog.com> (raw)
In-Reply-To: <cover.1749063024.git.Jonathan.Santos@analog.com>
From: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
The AD7768-1 has the ability to control other local hardware (such as gain
stages),to power down other blocks in the signal chain, or read local
status signals over the SPI interface.
Add direct mode conditional locks in the gpio callbacks to prevent register
access when the device is in buffered mode.
This change exports the AD7768-1's four gpios and makes them accessible
at an upper layer.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Co-developed-by: Jonathan Santos <Jonathan.Santos@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
---
v10 Changes:
* None.
v9 Changes:
* None.
v8 Changes:
* None.
v7 Changes:
* moved gpiochip field in the ad7768_state struct.
* replaced regmap_update_bits() for regmap_assign_bits() in the gpio_set() function.
* other nits.
* removed gpio.h header.
v6 Changes:
* Replaced deprecated .set callback with .set_rv.
v5 Changes:
* Use the new new iio_device_claim/release_direct() functions.
* replaced gpiochip_add_data() for devm_gpiochip_add_data().
v4 Changes:
* Mentioned in the commit message that we cannot tweak the GPIO controller
when the device is not in direct mode.
v3 Changes:
* Fixed SoB order.
* Added missing iio_device_release_direct_mode().
* Simplified some regmap writes.
* Removed ad7768_gpio_request() callback.
* Fixed line wrapping.
v2 Changes:
* Replaced mutex for iio_device_claim_direct_mode().
* Use gpio-controller property to conditionally enable the
GPIO support.
* OBS: when the GPIO is configured as output, we should read
the current state value from AD7768_REG_GPIO_WRITE.
---
drivers/iio/adc/ad7768-1.c | 140 ++++++++++++++++++++++++++++++++++++-
1 file changed, 138 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/adc/ad7768-1.c b/drivers/iio/adc/ad7768-1.c
index 68f876e5d31c..6efecb0e88b6 100644
--- a/drivers/iio/adc/ad7768-1.c
+++ b/drivers/iio/adc/ad7768-1.c
@@ -11,6 +11,7 @@
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/err.h>
+#include <linux/gpio/driver.h>
#include <linux/gpio/consumer.h>
#include <linux/interrupt.h>
#include <linux/minmax.h>
@@ -88,6 +89,16 @@
#define AD7768_REG_ANALOG2_VCM_MSK GENMASK(2, 0)
#define AD7768_REG_ANALOG2_VCM(x) FIELD_PREP(AD7768_REG_ANALOG2_VCM_MSK, (x))
+/* AD7768_REG_GPIO_CONTROL */
+#define AD7768_GPIO_UNIVERSAL_EN BIT(7)
+#define AD7768_GPIO_CONTROL_MSK GENMASK(3, 0)
+
+/* AD7768_REG_GPIO_WRITE */
+#define AD7768_GPIO_WRITE_MSK GENMASK(3, 0)
+
+/* AD7768_REG_GPIO_READ */
+#define AD7768_GPIO_READ_MSK GENMASK(3, 0)
+
#define AD7768_VCM_OFF 0x07
enum ad7768_conv_mode {
@@ -177,6 +188,7 @@ struct ad7768_state {
struct gpio_desc *gpio_sync_in;
struct gpio_desc *gpio_reset;
const char *labels[ARRAY_SIZE(ad7768_channels)];
+ struct gpio_chip gpiochip;
/*
* DMA (thus cache coherency maintenance) may require the
* transfer buffers to live in their own cache lines.
@@ -370,6 +382,122 @@ static int ad7768_set_dig_fil(struct ad7768_state *st,
return ad7768_send_sync_pulse(st);
}
+static int ad7768_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
+{
+ struct iio_dev *indio_dev = gpiochip_get_data(chip);
+ struct ad7768_state *st = iio_priv(indio_dev);
+ int ret;
+
+ if (!iio_device_claim_direct(indio_dev))
+ return -EBUSY;
+
+ ret = regmap_clear_bits(st->regmap, AD7768_REG_GPIO_CONTROL,
+ BIT(offset));
+ iio_device_release_direct(indio_dev);
+
+ return ret;
+}
+
+static int ad7768_gpio_direction_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct iio_dev *indio_dev = gpiochip_get_data(chip);
+ struct ad7768_state *st = iio_priv(indio_dev);
+ int ret;
+
+ if (!iio_device_claim_direct(indio_dev))
+ return -EBUSY;
+
+ ret = regmap_set_bits(st->regmap, AD7768_REG_GPIO_CONTROL,
+ BIT(offset));
+ iio_device_release_direct(indio_dev);
+
+ return ret;
+}
+
+static int ad7768_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct iio_dev *indio_dev = gpiochip_get_data(chip);
+ struct ad7768_state *st = iio_priv(indio_dev);
+ unsigned int val;
+ int ret;
+
+ if (!iio_device_claim_direct(indio_dev))
+ return -EBUSY;
+
+ ret = regmap_read(st->regmap, AD7768_REG_GPIO_CONTROL, &val);
+ if (ret)
+ goto err_release;
+
+ /*
+ * If the GPIO is configured as an output, read the current value from
+ * AD7768_REG_GPIO_WRITE. Otherwise, read the input value from
+ * AD7768_REG_GPIO_READ.
+ */
+ if (val & BIT(offset))
+ ret = regmap_read(st->regmap, AD7768_REG_GPIO_WRITE, &val);
+ else
+ ret = regmap_read(st->regmap, AD7768_REG_GPIO_READ, &val);
+ if (ret)
+ goto err_release;
+
+ ret = !!(val & BIT(offset));
+err_release:
+ iio_device_release_direct(indio_dev);
+
+ return ret;
+}
+
+static int ad7768_gpio_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+ struct iio_dev *indio_dev = gpiochip_get_data(chip);
+ struct ad7768_state *st = iio_priv(indio_dev);
+ unsigned int val;
+ int ret;
+
+ if (!iio_device_claim_direct(indio_dev))
+ return -EBUSY;
+
+ ret = regmap_read(st->regmap, AD7768_REG_GPIO_CONTROL, &val);
+ if (ret)
+ goto err_release;
+
+ if (val & BIT(offset))
+ ret = regmap_assign_bits(st->regmap, AD7768_REG_GPIO_WRITE,
+ BIT(offset), value);
+
+err_release:
+ iio_device_release_direct(indio_dev);
+
+ return ret;
+}
+
+static int ad7768_gpio_init(struct iio_dev *indio_dev)
+{
+ struct ad7768_state *st = iio_priv(indio_dev);
+ int ret;
+
+ ret = regmap_write(st->regmap, AD7768_REG_GPIO_CONTROL,
+ AD7768_GPIO_UNIVERSAL_EN);
+ if (ret)
+ return ret;
+
+ st->gpiochip = (struct gpio_chip) {
+ .label = "ad7768_1_gpios",
+ .base = -1,
+ .ngpio = 4,
+ .parent = &st->spi->dev,
+ .can_sleep = true,
+ .direction_input = ad7768_gpio_direction_input,
+ .direction_output = ad7768_gpio_direction_output,
+ .get = ad7768_gpio_get,
+ .set_rv = ad7768_gpio_set,
+ .owner = THIS_MODULE,
+ };
+
+ return devm_gpiochip_add_data(&st->spi->dev, &st->gpiochip, indio_dev);
+}
+
static int ad7768_set_freq(struct ad7768_state *st,
unsigned int freq)
{
@@ -511,8 +639,9 @@ static const struct iio_info ad7768_info = {
.debugfs_reg_access = &ad7768_reg_access,
};
-static int ad7768_setup(struct ad7768_state *st)
+static int ad7768_setup(struct iio_dev *indio_dev)
{
+ struct ad7768_state *st = iio_priv(indio_dev);
int ret;
st->gpio_reset = devm_gpiod_get_optional(&st->spi->dev, "reset",
@@ -545,6 +674,13 @@ static int ad7768_setup(struct ad7768_state *st)
if (IS_ERR(st->gpio_sync_in))
return PTR_ERR(st->gpio_sync_in);
+ /* Only create a Chip GPIO if flagged for it */
+ if (device_property_read_bool(&st->spi->dev, "gpio-controller")) {
+ ret = ad7768_gpio_init(indio_dev);
+ if (ret)
+ return ret;
+ }
+
/* Set the default sampling frequency to 32000 kSPS */
return ad7768_set_freq(st, 32000);
}
@@ -885,7 +1021,7 @@ static int ad7768_probe(struct spi_device *spi)
if (ret)
return ret;
- ret = ad7768_setup(st);
+ ret = ad7768_setup(indio_dev);
if (ret < 0) {
dev_err(&spi->dev, "AD7768 setup failed\n");
return ret;
--
2.34.1
next prev parent reply other threads:[~2025-06-04 19:37 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-06-04 19:35 [PATCH v10 00/12] iio: adc: ad7768-1: Add features, improvements, and fixes Jonathan Santos
2025-06-04 19:35 ` [PATCH v10 01/12] iio: adc: ad7768-1: Ensure SYNC_IN pulse minimum timing requirement Jonathan Santos
2025-06-04 20:14 ` David Lechner
2025-06-07 12:22 ` Jonathan Cameron
2025-06-04 19:35 ` [PATCH v10 02/12] dt-bindings: trigger-source: add generic GPIO trigger source Jonathan Santos
2025-06-04 19:35 ` [PATCH v10 03/12] dt-bindings: iio: adc: ad7768-1: add trigger-sources property Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 04/12] dt-bindings: iio: adc: ad7768-1: Document GPIO controller Jonathan Santos
2025-06-07 12:28 ` Jonathan Cameron
2025-06-04 19:36 ` [PATCH v10 05/12] dt-bindings: iio: adc: ad7768-1: document regulator provider property Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 06/12] iio: adc: ad7768-1: add regulator to control VCM output Jonathan Santos
2025-06-04 19:36 ` Jonathan Santos [this message]
2025-06-05 6:04 ` [PATCH v10 07/12] iio: adc: ad7768-1: Add GPIO controller support Andy Shevchenko
2025-06-06 19:37 ` Jonathan Santos
2025-06-04 19:36 ` [PATCH v10 08/12] iio: adc: ad7768-1: add multiple scan types to support 16-bits mode Jonathan Santos
2025-06-05 6:06 ` Andy Shevchenko
2025-06-04 19:37 ` [PATCH v10 09/12] iio: adc: ad7768-1: add support for Synchronization over SPI Jonathan Santos
2025-06-05 6:10 ` Andy Shevchenko
2025-06-07 12:20 ` Jonathan Cameron
2025-06-04 19:37 ` [PATCH v10 10/12] iio: adc: ad7768-1: replace manual attribute declaration Jonathan Santos
2025-06-04 19:37 ` [PATCH v10 11/12] iio: adc: ad7768-1: add filter type and oversampling ratio attributes Jonathan Santos
2025-06-05 6:21 ` Andy Shevchenko
2025-06-04 19:37 ` [PATCH v10 12/12] iio: adc: ad7768-1: add low pass -3dB cutoff attribute Jonathan Santos
2025-06-05 6:14 ` Andy Shevchenko
2025-06-05 6:23 ` [PATCH v10 00/12] iio: adc: ad7768-1: Add features, improvements, and fixes Andy Shevchenko
2025-06-07 12:34 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=eb48ea5f11503729b15a36ef00c89de3dd37bcc3.1749063024.git.Jonathan.Santos@analog.com \
--to=jonathan.santos@analog.com \
--cc=Michael.Hennerich@analog.com \
--cc=andy@kernel.org \
--cc=bartosz.golaszewski@linaro.org \
--cc=brgl@bgdev.pl \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=jic23@kernel.org \
--cc=jonath4nns@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marcelo.schmitt1@gmail.com \
--cc=marcelo.schmitt@analog.com \
--cc=nuno.sa@analog.com \
--cc=robh@kernel.org \
--cc=sergiu.cuciurean@analog.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).