Re: [PATCH 06/10] mfd: axp20x: Add support for AXP192

[Aidan MacDonald <aidanmacdonald.0x0@gmail.com>]

Lee Jones <lee.jones@linaro.org> writes:

> On Fri, 03 Jun 2022, Aidan MacDonald wrote:
>
>> The AXP192 PMIC is similar to the AXP202/AXP209, but with different
>> regulators, additional GPIOs, and a different IRQ register layout.
>> 
>> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
>> ---
>>  drivers/mfd/axp20x-i2c.c   |   2 +
>>  drivers/mfd/axp20x.c       | 150 +++++++++++++++++++++++++++++++++++++
>>  include/linux/mfd/axp20x.h |  84 +++++++++++++++++++++
>>  3 files changed, 236 insertions(+)
>> 
>> diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
>> index 00ab48018d8d..9ada58fad77f 100644
>> --- a/drivers/mfd/axp20x-i2c.c
>> +++ b/drivers/mfd/axp20x-i2c.c
>> @@ -62,6 +62,7 @@ static int axp20x_i2c_remove(struct i2c_client *i2c)
>>  #ifdef CONFIG_OF
>>  static const struct of_device_id axp20x_i2c_of_match[] = {
>>  	{ .compatible = "x-powers,axp152", .data = (void *)AXP152_ID },
>> +	{ .compatible = "x-powers,axp192", .data = (void *)AXP192_ID },
>>  	{ .compatible = "x-powers,axp202", .data = (void *)AXP202_ID },
>>  	{ .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
>>  	{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
>> @@ -75,6 +76,7 @@ MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match);
>>  
>>  static const struct i2c_device_id axp20x_i2c_id[] = {
>>  	{ "axp152", 0 },
>> +	{ "axp192", 0 },
>>  	{ "axp202", 0 },
>>  	{ "axp209", 0 },
>>  	{ "axp221", 0 },
>> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
>> index 8161a5dc68e8..7f64e5c83fe2 100644
>> --- a/drivers/mfd/axp20x.c
>> +++ b/drivers/mfd/axp20x.c
>> @@ -34,6 +34,7 @@
>>  
>>  static const char * const axp20x_model_names[] = {
>>  	"AXP152",
>> +	"AXP192",
>>  	"AXP202",
>>  	"AXP209",
>>  	"AXP221",
>> @@ -92,6 +93,35 @@ static const struct regmap_access_table axp20x_volatile_table = {
>>  	.n_yes_ranges	= ARRAY_SIZE(axp20x_volatile_ranges),
>>  };
>>  
>> +static const struct regmap_range axp192_writeable_ranges[] = {
>> +	regmap_reg_range(AXP192_DATACACHE(0), AXP192_DATACACHE(5)),
>> +	regmap_reg_range(AXP192_PWR_OUT_CTRL, AXP192_IRQ5_STATE),
>> +	regmap_reg_range(AXP20X_DCDC_MODE, AXP192_N_RSTO_CTRL),
>> +	regmap_reg_range(AXP20X_CC_CTRL, AXP20X_CC_CTRL),
>> +};
>> +
>> +static const struct regmap_range axp192_volatile_ranges[] = {
>> +	regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP192_USB_OTG_STATUS),
>> +	regmap_reg_range(AXP192_IRQ1_STATE, AXP192_IRQ4_STATE),
>> +	regmap_reg_range(AXP192_IRQ5_STATE, AXP192_IRQ5_STATE),
>> +	regmap_reg_range(AXP20X_ACIN_V_ADC_H, AXP20X_IPSOUT_V_HIGH_L),
>> +	regmap_reg_range(AXP20X_TIMER_CTRL, AXP20X_TIMER_CTRL),
>> +	regmap_reg_range(AXP192_GPIO2_0_STATE, AXP192_GPIO2_0_STATE),
>> +	regmap_reg_range(AXP192_GPIO4_3_STATE, AXP192_GPIO4_3_STATE),
>> +	regmap_reg_range(AXP192_N_RSTO_CTRL, AXP192_N_RSTO_CTRL),
>> +	regmap_reg_range(AXP20X_CHRG_CC_31_24, AXP20X_CC_CTRL),
>> +};
>> +
>> +static const struct regmap_access_table axp192_writeable_table = {
>> +	.yes_ranges	= axp192_writeable_ranges,
>> +	.n_yes_ranges	= ARRAY_SIZE(axp192_writeable_ranges),
>> +};
>> +
>> +static const struct regmap_access_table axp192_volatile_table = {
>> +	.yes_ranges	= axp192_volatile_ranges,
>> +	.n_yes_ranges	= ARRAY_SIZE(axp192_volatile_ranges),
>> +};
>> +
>>  /* AXP22x ranges are shared with the AXP809, as they cover the same range */
>>  static const struct regmap_range axp22x_writeable_ranges[] = {
>>  	regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
>> @@ -173,6 +203,25 @@ static const struct resource axp152_pek_resources[] = {
>>  	DEFINE_RES_IRQ_NAMED(AXP152_IRQ_PEK_FAL_EDGE, "PEK_DBF"),
>>  };
>>  
>> +static const struct resource axp192_gpio_resources[] = {
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO0_INPUT, "GPIO0"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO1_INPUT, "GPIO1"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_GPIO2_INPUT, "GPIO2"),
>> +};
>> +
>> +static const struct resource axp192_ac_power_supply_resources[] = {
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_ACIN_OVER_V, "ACIN_OVER_V"),
>> +};
>> +
>> +static const struct resource axp192_usb_power_supply_resources[] = {
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_PLUGIN, "VBUS_PLUGIN"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_REMOVAL, "VBUS_REMOVAL"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_VALID, "VBUS_VALID"),
>> +	DEFINE_RES_IRQ_NAMED(AXP192_IRQ_VBUS_NOT_VALID, "VBUS_NOT_VALID"),
>> +};
>> +
>>  static const struct resource axp20x_ac_power_supply_resources[] = {
>>  	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_PLUGIN, "ACIN_PLUGIN"),
>>  	DEFINE_RES_IRQ_NAMED(AXP20X_IRQ_ACIN_REMOVAL, "ACIN_REMOVAL"),
>> @@ -245,6 +294,15 @@ static const struct regmap_config axp152_regmap_config = {
>>  	.cache_type	= REGCACHE_RBTREE,
>>  };
>>  
>> +static const struct regmap_config axp192_regmap_config = {
>> +	.reg_bits	= 8,
>> +	.val_bits	= 8,
>> +	.wr_table	= &axp192_writeable_table,
>> +	.volatile_table	= &axp192_volatile_table,
>> +	.max_register	= AXP20X_CC_CTRL,
>> +	.cache_type	= REGCACHE_RBTREE,
>> +};
>> +
>>  static const struct regmap_config axp20x_regmap_config = {
>>  	.reg_bits	= 8,
>>  	.val_bits	= 8,
>> @@ -304,6 +362,55 @@ static const struct regmap_irq axp152_regmap_irqs[] = {
>>  	INIT_REGMAP_IRQ(AXP152, GPIO0_INPUT,		2, 0),
>>  };
>>  
>> +static const struct regmap_irq axp192_regmap_irqs[] = {
>> +	INIT_REGMAP_IRQ(AXP192, ACIN_OVER_V,		0, 7),
>> +	INIT_REGMAP_IRQ(AXP192, ACIN_PLUGIN,		0, 6),
>> +	INIT_REGMAP_IRQ(AXP192, ACIN_REMOVAL,		0, 5),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_OVER_V,		0, 4),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_PLUGIN,		0, 3),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_REMOVAL,		0, 2),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_V_LOW,		0, 1),
>> +	INIT_REGMAP_IRQ(AXP192, BATT_PLUGIN,		1, 7),
>> +	INIT_REGMAP_IRQ(AXP192, BATT_REMOVAL,	        1, 6),
>> +	INIT_REGMAP_IRQ(AXP192, BATT_ENT_ACT_MODE,	1, 5),
>> +	INIT_REGMAP_IRQ(AXP192, BATT_EXIT_ACT_MODE,	1, 4),
>> +	INIT_REGMAP_IRQ(AXP192, CHARG,		        1, 3),
>> +	INIT_REGMAP_IRQ(AXP192, CHARG_DONE,		1, 2),
>> +	INIT_REGMAP_IRQ(AXP192, BATT_TEMP_HIGH,	        1, 1),
>> +	INIT_REGMAP_IRQ(AXP192, BATT_TEMP_LOW,	        1, 0),
>> +	INIT_REGMAP_IRQ(AXP192, DIE_TEMP_HIGH,	        2, 7),
>> +	INIT_REGMAP_IRQ(AXP192, CHARG_I_LOW,		2, 6),
>> +	INIT_REGMAP_IRQ(AXP192, DCDC1_V_LONG,	        2, 5),
>> +	INIT_REGMAP_IRQ(AXP192, DCDC2_V_LONG,	        2, 4),
>> +	INIT_REGMAP_IRQ(AXP192, DCDC3_V_LONG,	        2, 3),
>> +	INIT_REGMAP_IRQ(AXP192, PEK_SHORT,		2, 1),
>> +	INIT_REGMAP_IRQ(AXP192, PEK_LONG,		2, 0),
>> +	INIT_REGMAP_IRQ(AXP192, N_OE_PWR_ON,		3, 7),
>> +	INIT_REGMAP_IRQ(AXP192, N_OE_PWR_OFF,	        3, 6),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_VALID,		3, 5),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_NOT_VALID,	        3, 4),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_SESS_VALID,	3, 3),
>> +	INIT_REGMAP_IRQ(AXP192, VBUS_SESS_END,	        3, 2),
>> +	INIT_REGMAP_IRQ(AXP192, LOW_PWR_LVL,	        3, 0),
>> +	INIT_REGMAP_IRQ(AXP192, TIMER,			4, 7),
>> +	INIT_REGMAP_IRQ(AXP192, GPIO2_INPUT,		4, 2),
>> +	INIT_REGMAP_IRQ(AXP192, GPIO1_INPUT,		4, 1),
>> +	INIT_REGMAP_IRQ(AXP192, GPIO0_INPUT,		4, 0),
>> +};
>> +
>> +static int axp192_get_irq_reg(unsigned int base_reg, int i)
>
> Nit: If you have to respin this set, please rename 'i'.
>
> Unless used as an iterator, 'i' is a terrible variable name.
>

Ack. I had to rework the regmap changes and split them out to their
own series, so I'll fix this when I rebase.

>> +{
>> +	/* linear mapping for IRQ1 to IRQ4 */
>> +	if (i < 4)
>> +		return base_reg + i;
>> +
>> +	/* handle IRQ5 separately */
>> +	if (base_reg == AXP192_IRQ1_EN)
>> +		return AXP192_IRQ5_EN;
>> +	else
>> +		return AXP192_IRQ5_STATE;
>> +}
>> +
>>  static const struct regmap_irq axp20x_regmap_irqs[] = {
>>  	INIT_REGMAP_IRQ(AXP20X, ACIN_OVER_V,		0, 7),
>>  	INIT_REGMAP_IRQ(AXP20X, ACIN_PLUGIN,		0, 6),
>> @@ -514,6 +621,19 @@ static const struct regmap_irq_chip axp152_regmap_irq_chip = {
>>  	.num_regs		= 3,
>>  };
>>  
>> +static const struct regmap_irq_chip axp192_regmap_irq_chip = {
>> +	.name			= "axp192_irq_chip",
>> +	.status_base		= AXP192_IRQ1_STATE,
>> +	.ack_base		= AXP192_IRQ1_STATE,
>> +	.mask_base		= AXP192_IRQ1_EN,
>> +	.mask_invert		= true,
>> +	.init_ack_masked	= true,
>> +	.irqs			= axp192_regmap_irqs,
>> +	.num_irqs		= ARRAY_SIZE(axp192_regmap_irqs),
>> +	.num_regs		= 5,
>> +	.get_irq_reg		= axp192_get_irq_reg,
>> +};
>> +
>>  static const struct regmap_irq_chip axp20x_regmap_irq_chip = {
>>  	.name			= "axp20x_irq_chip",
>>  	.status_base		= AXP20X_IRQ1_STATE,
>> @@ -588,6 +708,30 @@ static const struct regmap_irq_chip axp809_regmap_irq_chip = {
>>  	.num_regs		= 5,
>>  };
>>  
>> +static const struct mfd_cell axp192_cells[] = {
>> +	{
>> +		.name		= "axp192-gpio",
>> +		.of_compatible	= "x-powers,axp192-gpio",
>> +		.num_resources	= ARRAY_SIZE(axp192_gpio_resources),
>> +		.resources	= axp192_gpio_resources,
>> +	}, {
>> +		.name		= "axp20x-regulator",
>
> Nit: Is it possible to put one line entries at the bottom?
>
> And format like this:
>
>     { .name = "axp20x-regulator" }
>

OK.

>> +	}, {
>> +		.name		= "axp192-adc",
>> +		.of_compatible	= "x-powers,axp192-adc",
>> +	}, {
>> +		.name		= "axp20x-ac-power-supply",
>> +		.of_compatible	= "x-powers,axp202-ac-power-supply",
>> +		.num_resources	= ARRAY_SIZE(axp192_ac_power_supply_resources),
>> +		.resources	= axp192_ac_power_supply_resources,
>> +	}, {
>> +		.name		= "axp20x-usb-power-supply",
>> +		.of_compatible	= "x-powers,axp192-usb-power-supply",
>> +		.num_resources	= ARRAY_SIZE(axp192_usb_power_supply_resources),
>> +		.resources	= axp192_usb_power_supply_resources,
>> +	}
>> +};
>
> For my own reference (apply this as-is to your sign-off block):
>
>   Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>

Thanks!

Regards, Aidan