Re: Problem with IDE driver not claiming the disk

[Scott James Remnant <scott@ubuntu.com>]

[-- Attachment #1.1: Type: text/plain, Size: 3733 bytes --]

Thanks for replying so quickly,

On Tue, 2005-12-06 at 01:34 +0100, Bartlomiej Zolnierkiewicz wrote:

> On 12/6/05, Scott James Remnant <scott@ubuntu.com> wrote:
> > We've been having some IDE problems at Ubuntu Towers and can't seem to
> > figure out what's up, and I was hoping you guys might instantly spot
> > what we're doing wrong ...
> >
> > In order to get those events, and find out what's on the bus, we
> > explicitly load the "ide-generic" driver.  This spawns a whole number of
> > events, creating a whole array of devices -- /dev/hda* and friends.
> 
> This sounds very, very wrong.  Devices should be probed and
> registered by alim15x3/via82cxxx and not ide-generic driver.
> 
Right, that's not happening for any of the drivers -- so far I haven't
found an IDE driver that, when loaded, probes for devices and registers
them.  They all need ide-generic to be loaded to "kick" them.

> > Do you concur?  What are we doing wrong, or what is the driver doing
> > wrong?
> 
> We can only guess without dmesg and lspci -vvv.
> 
Certainly...

On the alim15x3 machine:

modprobe pci:.... as a result of touching the uevent file for that
device; loads the ide-core, alim15x3 and "generic" modules.  dmesg
output:

	Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
	ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
	ACPI: bus type ide registered

modprobe ide-generic - currently hard-coded into our initramfs script.
dmesg output:

	ALI15X3: IDE controller at PCI slot 0000:00:10.0
	ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 10
	PCI: setting IRQ 10 as level-triggered
	ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [C0C5] -> GSI 10 (level, low) -> IRQ 10
	ALI15X3: chipset revision 196
	ALI15X3: not 100% native mode: will probe irqs later
	    ide0: BM-DMA at 0x3800-0x3807, BIOS settings: hda:DMA, hdb:pio
	ALI15X3: simplex device: DMA forced
	    ide1: BM-DMA at 0x3808-0x380f, BIOS settings: hdc:DMA, hdd:DMA
	Probing IDE interface ide0...
	hda: HTS548040M9AT00, ATA DISK drive
	ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
	Probing IDE interface ide1...
	Probing IDE interface ide1...
	hda: max request size: 128KiB
	hda: 78140160 sectors (40007 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(100)
	hda: cache flushes supported
	hda: hda1 hda2 < hda5 > hda3

(Full dmesg attached as alim-dmesg)

As you can see, the probing doesn't take place until after ide-generic
is loaded -- I left long gaps between doing each bit so it's reasonably
obvious in the dmesg output.

lspci of that device:

0000:00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if ea)
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (500ns min, 1000ns max)
	Interrupt: pin A routed to IRQ 10
	Region 4: I/O ports at 3800 [size=16]
	Capabilities: <available only to root>

(Full lspci attached as alim-lspci)

> You didn't even tell your kernel version and whether this
> is vanilla kernel or Ubuntu one (do you have any extra
> IDE patches?).
> 
I was first hoping it was a glaringly obvious thing we were doing wrong,
and wouldn't come to comparing kernel code;  the kernel is the current
Ubuntu one, it's based off 2.6.15 -- our patches are all in git:

http://www.kernel.org/git/?p=linux/kernel/git/bcollins/ubuntu-2.6.git

I'm not best placed to answer the patches that are in the exact version
I used ("our" 2.6.15-6.8), Ben Collins is (Cc'd).

Scott
-- 
Scott James Remnant
scott@ubuntu.com

[-- Attachment #1.2: alim-dmesg --]
[-- Type: text/plain, Size: 15899 bytes --]

 ACPI: Using PIC for interrupt routing
[17179572.720000] ACPI: PCI Root Bridge [C045] (0000:00)
[17179572.720000] PCI: Probing PCI hardware (bus 00)
[17179572.720000] ACPI: Assume root bridge [\_SB_.C045] bus is 0
[17179572.728000] PCI quirk: region 1000-103f claimed by ali7101 ACPI
[17179572.728000] PCI quirk: region 1100-111f claimed by ali7101 SMB
[17179572.728000] Boot video device is 0000:01:05.0
[17179572.728000] ACPI: PCI Interrupt Routing Table [\_SB_.C045._PRT]
[17179572.760000] ACPI: PCI Interrupt Routing Table [\_SB_.C045.C046._PRT]
[17179572.760000] ACPI: Embedded Controller [C0E6] (gpe 24)
[17179572.768000] ACPI: Power Resource [C15B] (on)
[17179572.772000] ACPI: Power Resource [C160] (on)
[17179572.772000] ACPI: Power Resource [C16A] (on)
[17179572.772000] ACPI: Power Resource [C17B] (on)
[17179572.772000] ACPI: PCI Interrupt Link [C0C5] (IRQs 5 *10 11)
[17179572.776000] ACPI: PCI Interrupt Link [C0C6] (IRQs 5 *10 11)
[17179572.776000] ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10 *11)
[17179572.776000] ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10 11) *0, disabled.
[17179572.776000] ACPI: PCI Interrupt Link [C0C9] (IRQs 5 *10 11)
[17179572.776000] ACPI: PCI Interrupt Link [C0CA] (IRQs *5 10 11)
[17179572.776000] ACPI: PCI Interrupt Link [C0CB] (IRQs 5 10 *11)
[17179572.776000] ACPI: PCI Interrupt Link [C0CC] (IRQs 5 10 *11)
[17179572.780000] ACPI: Power Resource [C1E9] (off)
[17179572.780000] ACPI: Power Resource [C1EA] (off)
[17179572.780000] ACPI: Power Resource [C1EB] (off)
[17179572.780000] ACPI: Power Resource [C1EC] (off)
[17179572.780000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179572.780000] pnp: PnP ACPI init
[17179572.792000] pnp: PnP ACPI: found 15 devices
[17179572.792000] PnPBIOS: Disabled by ACPI PNP
[17179572.792000] PCI: Using ACPI for IRQ routing
[17179572.792000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179572.848000] pnp: 00:0c: ioport range 0x1000-0x107f could not be reserved
[17179572.848000] pnp: 00:0c: ioport range 0x1100-0x111f has been reserved
[17179572.848000] PCI: Bridge: 0000:00:01.0
[17179572.848000]   IO window: 2000-2fff
[17179572.848000]   MEM window: 90000000-900fffff
[17179572.848000]   PREFETCH window: 94000000-97ffffff
[17179572.848000] PCI: Bus 2, cardbus bridge: 0000:00:0b.0
[17179572.848000]   IO window: 00001800-000018ff
[17179572.848000]   IO window: 00001c00-00001cff
[17179572.848000]   PREFETCH window: 40000000-41ffffff
[17179572.848000]   MEM window: 42000000-43ffffff
[17179572.848000] PCI: Bus 6, cardbus bridge: 0000:00:0b.1
[17179572.848000]   IO window: 00003c00-00003cff
[17179572.848000]   IO window: 00004000-000040ff
[17179572.848000]   PREFETCH window: 44000000-45ffffff
[17179572.848000]   MEM window: 46000000-47ffffff
[17179572.848000] ACPI: PCI Interrupt Link [C0C7] enabled at IRQ 11
[17179572.848000] PCI: setting IRQ 11 as level-triggered
[17179572.848000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
[17179572.848000] ACPI: PCI Interrupt 0000:00:0b.1[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
[17179572.848000] audit: initializing netlink socket (disabled)
[17179572.848000] audit(1133831803.844:1): initialized
[17179572.848000] highmem bounce pool size: 64 pages
[17179572.848000] VFS: Disk quotas dquot_6.5.1
[17179572.848000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179572.848000] Initializing Cryptographic API
[17179572.848000] io scheduler noop registered
[17179572.848000] io scheduler anticipatory registered
[17179572.848000] io scheduler deadline registered
[17179572.848000] io scheduler cfq registered
[17179572.848000] Activating ISA DMA hang workarounds.
[17179572.848000] isapnp: Scanning for PnP cards...
[17179573.204000] isapnp: No Plug & Play device found
[17179573.220000] PNP: PS/2 Controller [PNP0303:C178,PNP0f13:C179] at 0x60,0x64 irq 1,12
[17179573.220000] i8042.c: Detected active multiplexing controller, rev 1.1.
[17179573.220000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[17179573.220000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[17179573.220000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[17179573.220000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[17179573.220000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179573.220000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179573.220000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.220000] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[17179573.224000] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179573.224000] ACPI: PCI Interrupt Link [C0CB] enabled at IRQ 11
[17179573.224000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [C0CB] -> GSI 11 (level, low) -> IRQ 11
[17179573.224000] 0000:00:08.0: ttyS1 at I/O 0x3428 (irq = 11) is a 8250
[17179573.224000] 0000:00:08.0: ttyS3 at I/O 0x3440 (irq = 11) is a 8250
[17179573.224000] Couldn't register serial port 0000:00:08.0: -28
[17179573.224000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179573.224000] EISA: Probing bus 0 at eisa.0
[17179573.224000] Cannot allocate resource for EISA slot 1
[17179573.224000] Cannot allocate resource for EISA slot 2
[17179573.224000] Cannot allocate resource for EISA slot 3
[17179573.224000] Cannot allocate resource for EISA slot 4
[17179573.224000] EISA: Detected 0 cards.
[17179573.224000] NET: Registered protocol family 2
[17179573.260000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179573.264000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179573.264000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[17179573.264000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[17179573.268000] TCP: Hash tables configured (established 131072 bind 65536)
[17179573.268000] TCP reno registered
[17179573.268000] TCP bic registered
[17179573.268000] NET: Registered protocol family 8
[17179573.268000] NET: Registered protocol family 20
[17179573.268000] Using IPI No-Shortcut mode
[17179573.268000] ACPI wakeup devices: 
[17179573.268000] C045 C0BA C184 C189 C18A 
[17179573.268000] ACPI: (supports S0 S3 S4 S5)
[17179573.268000] Freeing unused kernel memory: 308k freed
[17179573.332000] Capability LSM initialized
[17179573.348000] NET: Registered protocol family 1
[17179578.164000] ACPI: Fan [C1ED] (off)
[17179578.164000] ACPI: Fan [C1EE] (off)
[17179578.164000] ACPI: Fan [C1EF] (off)
[17179578.164000] ACPI: Fan [C1F0] (off)
[17179578.168000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[17179578.176000] ACPI: Thermal Zone [TZ1] (73 C)
[17179578.180000] ACPI: Thermal Zone [TZ2] (59 C)
[17179578.188000] ACPI: Thermal Zone [TZ3] (33 C)
[17179628.784000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179628.784000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179628.784000] ACPI: bus type ide registered
[17179666.712000] ALI15X3: IDE controller at PCI slot 0000:00:10.0
[17179666.712000] ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 10
[17179666.712000] PCI: setting IRQ 10 as level-triggered
[17179666.712000] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [C0C5] -> GSI 10 (level, low) -> IRQ 10
[17179666.712000] ALI15X3: chipset revision 196
[17179666.712000] ALI15X3: not 100% native mode: will probe irqs later
[17179666.712000]     ide0: BM-DMA at 0x3800-0x3807, BIOS settings: hda:DMA, hdb:pio
[17179666.712000] ALI15X3: simplex device: DMA forced
[17179666.712000]     ide1: BM-DMA at 0x3808-0x380f, BIOS settings: hdc:DMA, hdd:DMA
[17179666.712000] Probing IDE interface ide0...
[17179667.004000] hda: HTS548040M9AT00, ATA DISK drive
[17179667.676000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179667.676000] Probing IDE interface ide1...
[17179668.240000] Probing IDE interface ide1...
[17179668.260000] hda: max request size: 128KiB
[17179668.584000] hda: 78140160 sectors (40007 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(100)
[17179668.584000] hda: cache flushes supported
[17179668.584000]  hda: hda1 hda2 < hda5 > hda3
[17179696.584000] Attempting manual resume
[17179696.644000] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[17179696.644000] SGI XFS Quota Management subsystem
[17179696.696000] XFS mounting filesystem hda3
[17179696.848000] Ending clean XFS mount for filesystem: hda3
[17179698.744000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179698.744000] md: bitmap version 4.39
[17179702.956000] Adding 1622524k swap on /dev/hda5.  Priority:-1 extents:1 across:1622524k
[17179705.724000] Linux agpgart interface v0.101 (c) Dave Jones
[17179705.736000] agpgart: Detected Ati IGP345M chipset
[17179705.748000] agpgart: AGP aperture is 64M @ 0x9c000000
[17179705.920000] ali15x3_smbus 0000:00:11.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[17179705.924000] ali15x3_smbus 0000:00:11.0: ALI15X3 not detected, module not inserted.
[17179706.108000] usbcore: registered new driver usbfs
[17179706.108000] usbcore: registered new driver hub
[17179706.224000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
[17179706.224000] Yenta: CardBus bridge found at 0000:00:0b.0 [0e11:005a]
[17179706.224000] Yenta O2: res at 0x94/0xD4: 00/ea
[17179706.224000] Yenta O2: enabling read prefetch/write burst
[17179706.240000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179706.308000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179706.308000] ath_hal: module license 'Proprietary' taints kernel.
[17179706.308000] ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
[17179706.352000] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[17179706.352000] Socket status: 30000006
[17179706.376000] ACPI: PCI Interrupt 0000:00:0b.1[A] -> Link [C0C7] -> GSI 11 (level, low) -> IRQ 11
[17179706.376000] Yenta: CardBus bridge found at 0000:00:0b.1 [0e11:005a]
[17179706.384000] wlan: 0.8.6.0 (EXPERIMENTAL)
[17179706.404000] ath_rate_sample: 1.2
[17179706.504000] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[17179706.504000] Socket status: 30000006
[17179706.544000] ath_pci: 0.9.6.0 (EXPERIMENTAL)
[17179706.544000] ACPI: PCI Interrupt Link [C0CA] enabled at IRQ 5
[17179706.544000] PCI: setting IRQ 5 as level-triggered
[17179706.544000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [C0CA] -> GSI 5 (level, low) -> IRQ 5
[17179706.844000] Build date: Dec  5 2005
[17179706.844000] Debugging version (IEEE80211)
[17179706.844000] ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[17179706.844000] ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[17179706.844000] ath0: H/W encryption support: WEP AES AES_CCM TKIP
[17179706.844000] ath0: mac 5.6 phy 4.1 radio 1.7
[17179706.844000] ath0: Use hw queue 1 for WME_AC_BE traffic
[17179706.844000] ath0: Use hw queue 0 for WME_AC_BK traffic
[17179706.844000] ath0: Use hw queue 2 for WME_AC_VI traffic
[17179706.844000] ath0: Use hw queue 3 for WME_AC_VO traffic
[17179706.844000] ath0: Use hw queue 8 for CAB traffic
[17179706.844000] ath0: Use hw queue 9 for beacons
[17179706.844000] Debugging version (ATH)
[17179706.844000] ath0: Atheros 5212: mem=0x98080000, irq=5
[17179706.844000] ACPI: PCI Interrupt Link [C0C6] enabled at IRQ 10
[17179706.844000] ACPI: PCI Interrupt 0000:00:12.2[C] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
[17179706.844000] ehci_hcd 0000:00:12.2: EHCI Host Controller
[17179706.844000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
[17179706.844000] ohci_hcd 0000:00:12.0: OHCI Host Controller
[17179706.844000] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1
[17179706.844000] ohci_hcd 0000:00:12.0: irq 10, io mem 0x98380000
[17179706.864000] input: PC Speaker as /class/input/input1
[17179706.876000] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 2
[17179706.876000] ehci_hcd 0000:00:12.2: irq 10, io mem 0x98480000
[17179706.876000] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179706.876000] hub 2-0:1.0: USB hub found
[17179706.876000] hub 2-0:1.0: 5 ports detected
[17179706.980000] hub 1-0:1.0: USB hub found
[17179706.980000] hub 1-0:1.0: 3 ports detected
[17179706.980000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179707.012000] parport: PnPBIOS parport detected.
[17179707.012000] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[17179707.084000] ACPI: PCI Interrupt 0000:00:12.1[B] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
[17179707.084000] ohci_hcd 0000:00:12.1: OHCI Host Controller
[17179707.084000] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 3
[17179707.084000] ohci_hcd 0000:00:12.1: irq 10, io mem 0x98400000
[17179707.172000] hub 3-0:1.0: USB hub found
[17179707.172000] hub 3-0:1.0: 2 ports detected
[17179707.216000] ACPI: PCI Interrupt Link [C0CC] enabled at IRQ 11
[17179707.216000] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [C0CC] -> GSI 11 (level, low) -> IRQ 11
[17179707.592000] tg3.c:v3.43 (Oct 24, 2005)
[17179707.592000] ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 10
[17179707.592000] ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [C0C9] -> GSI 10 (level, low) -> IRQ 10
[17179707.652000] eth0: Tigon3 [partno(BCM5705mA1) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:12:79:59:8d:38
[17179707.652000] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1] 
[17179707.652000] eth0: dma_rwctrl[763f0000]
[17179707.812000] usb 1-3: new full speed USB device using ohci_hcd and address 2
[17179710.436000] Real Time Clock Driver v1.12
[17179713.064000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, caps: 0xa84793/0x100000
[17179713.064000] serio: Synaptics pass-through port at isa0060/serio4/input0
[17179713.112000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
[17179718.332000] ts: Compaq touchscreen protocol output
[17179718.364000] Bluetooth: Core ver 2.8
[17179718.364000] NET: Registered protocol family 31
[17179718.364000] Bluetooth: HCI device and connection manager initialized
[17179718.364000] Bluetooth: HCI socket layer initialized
[17179718.412000] mice: PS/2 mouse device common for all mice
[17179718.456000] Bluetooth: HCI USB driver ver 2.9
[17179718.456000] usbcore: registered new driver hci_usb
[17179718.504000] cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
[17179718.508000] cs: IO port probe 0xc00-0xcf7: clean.
[17179718.508000] cs: IO port probe 0xa00-0xaff: clean.
[17179718.512000] cs: IO port probe 0x100-0x4ff: excluding 0x200-0x207 0x220-0x22f 0x330-0x337 0x388-0x38f 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
[17179718.516000] cs: IO port probe 0xc00-0xcf7: clean.
[17179718.516000] cs: IO port probe 0xa00-0xaff: clean.
[17179719.352000] AC'97 1 does not respond - RESET
[17179719.352000] AC'97 1 access is not valid [0xffffffff], removing mixer.
[17179719.352000] ali mixer 1 creating error.
[17179719.828000] Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version 0.14.10j-2.6, 04:17:30 Dec  1 2005
[17179722.088000] lp0: using parport0 (interrupt-driven).
[17179723.300000] input: PS/2 Generic Mouse as /class/input/input3
[17179725.000000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[17179726.824000] kjournald starting.  Commit interval 5 seconds
[17179726.824000] EXT3 FS on hda1, internal journal
[17179726.824000] EXT3-fs: mounted filesystem with ordered data mode.

[-- Attachment #1.3: alim-lspci --]
[-- Type: text/plain, Size: 9091 bytes --]

0000:00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Region 0: Memory at 9c000000 (32-bit, prefetchable) [size=64M]
	Region 1: Memory at 98500000 (32-bit, prefetchable) [size=4K]
	Capabilities: <available only to root>

0000:00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 99
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=66
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: 90000000-900fffff
	Prefetchable memory behind bridge: 94000000-97ffffff
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

0000:00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+
	Latency: 64 (500ns min, 6000ns max)
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 3000 [size=256]
	Region 1: Memory at 98100000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <available only to root>

0000:00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: <available only to root>

0000:00:08.0 Modem: ALi Corporation M5457 AC'97 Modem Controller (prog-if 00 [Generic])
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 98180000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at 3400 [size=256]
	Capabilities: <available only to root>

0000:00:09.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
	Subsystem: Compaq Computer Corporation: Unknown device 00e6
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at 98080000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: <available only to root>

0000:00:0b.0 CardBus bridge: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus Controller (rev 20)
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 98200000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 40000000-41fff000 (prefetchable)
	Memory window 1: 42000000-43fff000
	I/O window 0: 00001800-000018ff
	I/O window 1: 00001c00-00001cff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

0000:00:0b.1 CardBus bridge: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus Controller (rev 20)
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 168
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 98280000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 44000000-45fff000 (prefetchable)
	Memory window 1: 46000000-47fff000
	I/O window 0: 00003c00-00003cff
	I/O window 1: 00004000-000040ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001

0000:00:0b.2 System peripheral: O2 Micro, Inc. OZ711Mx 4-in-1 MemoryCardBus Accelerator
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 98300000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <available only to root>

0000:00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4) (prog-if ea)
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (500ns min, 1000ns max)
	Interrupt: pin A routed to IRQ 10
	Region 4: I/O ports at 3800 [size=16]
	Capabilities: <available only to root>

0000:00:11.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

0000:00:12.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 98380000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <available only to root>

0000:00:12.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin B routed to IRQ 10
	Region 0: Memory at 98400000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <available only to root>

0000:00:12.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin C routed to IRQ 10
	Region 0: Memory at 98480000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <available only to root>

0000:00:13.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet (rev 03)
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 98000000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at 48000000 [disabled] [size=64K]
	Capabilities: <available only to root>

0000:01:05.0 VGA compatible controller: ATI Technologies Inc Radeon IGP 330M/340M/350M (prog-if 00 [VGA])
	Subsystem: Compaq Computer Corporation: Unknown device 005a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64 (2000ns min), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 94000000 (32-bit, prefetchable) [size=64M]
	Region 1: I/O ports at 2000 [size=256]
	Region 2: Memory at 90000000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at 90020000 [disabled] [size=128K]
	Capabilities: <available only to root>


[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]