USB printing support problems

USB printing support problems

[David Cannings]

I have an Intel L440GX+ SMP motherboard which has two onboard USB ports.  I am 
trying to get a Samsung ML-1210 printer, which works fine in Windows, to work 
with a 2.6.8 kernel (patched with the Gentoo patches).

After compiling EHCI, OHCI and UHCI as modules and running hotplug, I get 
errors in syslog when a device is plugged in.  There are no options in my 
BIOS concerning the onboard USB.

Is there anything I can do to get USB working?  I'm guessing it's a problem 
with the USB subsystem but am not sure where to turn for more information.

Thanks,

David

-- Output from syslog upon plugging in a device --
kernel: usb 1-1: new full speed USB device using address 2
kernel: uhci_hcd 0000:00:12.2: uhci_result_control: failed with status 440000
kernel: [f73d9240] link (373d91e2) element (3730d040)
kernel:   0: [f730d040] link (3730d080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 
DT0 EndPt=0 Dev=0, PID-(SETUP) (buf716f3a0)
kernel:   1: [f730d080] link (00000001) e3 IOC Active Length=0 MaxLen\x7ff DT1 
EndPt=0 Dev=0, PIDi(IN) (buf\0000000)
kernel:
kernel: uhci_hcd 0000:00:12.2: uhci_result_control: failed with status 440000
kernel: [f73d9240] link (373d91e2) element (3730d040)
kernel:   0: [f730d040] link (3730d080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 
DT0 EndPt=0 Dev=0, PID-(SETUP) (buf716f3a0)
kernel:   1: [f730d080] link (00000001) e3 IOC Active Length=0 MaxLen\x7ff DT1 
EndPt=0 Dev=0, PIDi(IN) (buf\0000000)
kernel:
kernel: usb 1-1: device not accepting address 2, error -71
kernel: usb 1-1: new full speed USB device using address 3
kernel: uhci_hcd 0000:00:12.2: uhci_result_control: failed with status 440000
kernel: [f73d9240] link (373d91e2) element (3730d040)
kernel:   0: [f730d040] link (3730d080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 
DT0 EndPt=0 Dev=0, PID-(SETUP) (buf716f3a0)
kernel:   1: [f730d080] link (00000001) e3 IOC Active Length=0 MaxLen\x7ff DT1 
EndPt=0 Dev=0, PIDi(IN) (buf\0000000)
kernel:
kernel: uhci_hcd 0000:00:12.2: uhci_result_control: failed with status 440000
kernel: [f73d9240] link (373d91e2) element (3730d040)
kernel:   0: [f730d040] link (3730d080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 
DT0 EndPt=0 Dev=0, PID-(SETUP) (buf716f3a0)
kernel:   1: [f730d080] link (00000001) e3 IOC Active Length=0 MaxLen\x7ff DT1 
EndPt=0 Dev=0, PIDi(IN) (buf\0000000)
kernel:
kernel: usb 1-1: device not accepting address 3, error -71

-- Output for USB from 'lspci -v' --
0000:00:12.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 
(prog-if 00 [UHCI])
        Flags: bus master, medium devsel, latency 64, IRQ 21
        I/O ports at 2060 [size2]


-------------------------------------------------------
This SF.Net email is sponsored by: YOU BE THE JUDGE. Be one of 170
Project Admins to receive an Apple iPod Mini FREE for your judgement on
who ports your project to Linux PPC the best. Sponsored by IBM.
Deadline: Sept. 24. Go here: http://sf.net/ppc_contest.php
_______________________________________________
Linux-hotplug-devel mailing list  http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel