From: Tobias Klauser <tklauser@access.unizh.ch>
To: linux-hotplug@vger.kernel.org
Subject: Re: usb multicard reader problems
Date: Sat, 16 Apr 2005 16:10:30 +0000 [thread overview]
Message-ID: <20050416161030.GA769@neon> (raw)
In-Reply-To: <4212FDE6000C59D9@mail-5.tiscali.it>
Please keep it on the list.
On Sat, Apr 16, 2005 at 01:01:39PM +0200, ziettopeu@tiscali.it wrote:
> read below the log pasted:
> Apr 14 21:32:33 localhost kernel: SCSI device sdc: 253952 512-byte hdwr sectors
> (130 MB)
> Apr 14 21:32:33 localhost kernel: sdc: Write Protect is off
> Apr 14 21:32:33 localhost kernel: sdc: assuming drive cache: write through
> Apr 14 21:32:33 localhost kernel: sdc: sdc1
> Apr 14 21:32:33 localhost kernel: Attached scsi removable disk sdc at scsi7,
> channel 0, id 0, lun 0
> Apr 14 21:32:33 localhost scsi.agent[5186]: disk at /devices/pci0000:00/0000:00:02.2/usb1/1-6/1-6:1.0/host7/7:0:0:0
> Apr 14 21:32:34 localhost fstab-sync[5277]: added mount point /media/usbdisk1
> for /dev/sdc1
> Apr 14 21:32:39 localhost kernel: sdc : READ CAPACITY failed.
> Apr 14 21:32:39 localhost kernel: sdc : status=0, message\0, host=7, driver\0
>
> Apr 14 21:32:39 localhost kernel: sdc : sense not available.
> Apr 14 21:32:39 localhost kernel: sdc: Write Protect is off
> Apr 14 21:32:39 localhost kernel: sdc: assuming drive cache: write through
> Apr 14 21:32:39 localhost kernel: sdc : READ CAPACITY failed.
> Apr 14 21:32:39 localhost kernel: sdc : status=0, message\0, host=7, driver\0
>
> Apr 14 21:32:39 localhost kernel: sdc : sense not available.
> Apr 14 21:32:39 localhost kernel: sdc: Write Protect is off
> Apr 14 21:32:39 localhost kernel: sdc: assuming drive cache: write through
> Apr 14 21:32:39 localhost kernel: sdc:<3>Buffer I/O error on device sdc,
> logical block 0
> Apr 14 21:32:39 localhost kernel: Buffer I/O error on device sdc, logical
> block 0
> Apr 14 21:32:39 localhost kernel: Buffer I/O error on device sdc, logical
> block 262143
> Apr 14 21:32:39 localhost kernel: Buffer I/O error on device sdc, logical
> block 262143
> Apr 14 21:32:39 localhost kernel: Buffer I/O error on device sdc, logical
> block 0
> Apr 14 21:32:39 localhost kernel: unable to read partition table
> Apr 14 21:32:39 localhost kernel: usb 1-6: USB disconnect, address 8
> Apr 14 21:32:40 localhost fstab-sync[5359]: removed mount point /media/usbdisk1
> for /dev/sdc1
> Apr 14 21:32:43 localhost kernel: ohci_hcd 0000:00:02.1: wakeup
> Apr 14 21:32:44 localhost kernel: usb 3-3: new full speed USB device using
> address 5
> Apr 14 21:32:44 localhost kernel: scsi8 : SCSI emulation for USB Mass Storage
> devices
> Apr 14 21:32:44 localhost kernel: Vendor: IC Model: USB Storage-CFC
> Rev: 322E
> Apr 14 21:32:44 localhost kernel: Type: Direct-Access
> ANSI SCSI revision: 02
> Apr 14 21:32:45 localhost kernel: sdc: Spinning up disk....ready
> Apr 14 21:32:45 localhost kernel: SCSI device sdc: 254464 512-byte hdwr sectors
> (130 MB)
> Apr 14 21:32:45 localhost kernel: sdc: Write Protect is off
> Apr 14 21:32:45 localhost kernel: sdc: assuming drive cache: write through
> Apr 14 21:32:49 localhost kernel: sdc:<4>usb 3-3: control timeout on ep0in
> Apr 14 21:32:49 localhost wait_for_sysfs[5383]: either wait_for_sysfs (udev
> 039) needs an update to handle the device '/devices/pci0000:00/0000:00:02.1/usb3/3-3/3-3:1.0'
> properly (no bus device link) or the sysfs-support of your device's driver
> needs to be fixed, please report to <linux-hotplug-devel@lists.sourceforge.net>
> Apr 14 21:32:49 localhost wait_for_sysfs[5399]: either wait_for_sysfs (udev
> 039) needs an update to handle the device '/devices/pci0000:00/0000:00:02.1/usb3/3-3/3-3:1.0/host8/8:0:0:0'
> properly (no bus device link) or the sysfs-support of your device's driver
> needs to be fixed, please report to <linux-hotplug-devel@lists.sourceforge.net>
> Apr 14 21:32:50 localhost wait_for_sysfs[5407]: either wait_for_sysfs (udev
> 039) needs an update to handle the device '/block/sdc' properly (no bus device
> link) or the sysfs-support of your device's driver needs to be fixed, please
> report to <linux-hotplug-devel@lists.sourceforge.net>
Looks like your udev package needs an update, at least the message
above should go away then. The rest of the messages seem either kernel
or hal related.
> Apr 14 21:32:59 localhost hal.hotplug[5409]: timout(10000 ms) waiting for
> /devices/pci0000:00/0000:00:02.1/usb3/3-3/3-3:1.0
> Apr 14 21:32:59 localhost hal.hotplug[5413]: timout(10000 ms) waiting for
> /devices/pci0000:00/0000:00:02.1/usb3/3-3/3-3:1.0/host8/8:0:0:0
> Apr 14 21:33:09 localhost scsi.agent[5457]: Attribute /sys/devices/pci0000:00/0000:00:02.1/usb3/3-3/3-3:1.0/host8/8:0:0:0/type
> does not exist
> Apr 14 21:33:50 localhost kernel: end_request: I/O error, dev fd0, sector
> 0
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now.
http://ads.osdn.com/?ad_ide95&alloc_id\x14396&op=click
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
prev parent reply other threads:[~2005-04-16 16:10 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-04-16 0:57 usb multicard reader problems ziettopeu
2005-04-16 8:43 ` Tobias Klauser
2005-04-16 16:10 ` Tobias Klauser [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050416161030.GA769@neon \
--to=tklauser@access.unizh.ch \
--cc=linux-hotplug@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).