* USB failure (CS5536 not supported on linux 2.4.21-50?)
@ 2007-09-10 12:56 Brunner, Brian T.
2007-09-11 4:03 ` Brian Brunner
2007-09-11 17:46 ` Greg KH
0 siblings, 2 replies; 3+ messages in thread
From: Brunner, Brian T. @ 2007-09-10 12:56 UTC (permalink / raw)
To: linux-hotplug
Kernel 2.4.21-50 (CentOS 3.9)
1: This kernel on EPoX EP-KRAI8 PRO recognizes all USB devices and
mounts them. HappyHappyJoyJoy. (this is my development system).
2: This kernel on Congatec ETX-LX800 with CS5536 (companion chip that
inter alia provides the USB) recognizes none (this is my product target
system).
The kernel configurator knows of CS5530 but not CS5536, I have yet to
find a kernel module for this chip/kernel combo.
I know the thumbdrive devices (and hotplug in general) are good because
of the success on the development system.
I desire clues as to what is wrong in my target system.
Here is dmesg (with thumbdrive device plugged in), and /var/log/messages
of a hotplug after the next '=='
===================================
Linux version 2.4.21-50.EL.mcut (root@mcut16) (gcc version 3.2.3
20030502 (Red Hat Linux 3.2.3-59)) #5 Fri Sep 7 08:26:35 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fdc0000 (usable)
BIOS-e820: 0000000040400000 - 0000000040440004 (reserved)
BIOS-e820: 00000000f0000000 - 0000000100000000 (reserved) 509MB LOWMEM
available.
NX protection not present; using segment protection On node 0
totalpages: 130496
zone(0): 4096 pages.
zone(1): 126400 pages.
zone(2): 0 pages.
Kernel command line: ro root=/dev/hda2 hdb=ide-scsi 4
ide_setup: hdb=ide-scsi
Initializing CPU#0
Detected 498.017 MHz processor.
Calibrating delay loop... 987.13 BogoMIPS Page-cache hash table entries:
131072 (order: 7, 512 KB) Page-pin hash table entries: 32768 (order: 5,
128 KB) Dentry cache hash table entries: 65536 (order: 7, 512 KB) Inode
cache hash table entries: 32768 (order: 6, 256 KB) Buffer cache hash
table entries: 32768 (order: 5, 128 KB)
Memory: 508128k/521984k available (1801k kernel code, 11292k reserved,
635k data, 136k init, 0k highmem) zapping low mappings.
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 128K (32 bytes/line)
CPU: After generic, caps: 0088a93d c0c0a13d 00000000 00000000
CPU: Common caps: 0088a93d c0c0a13d 00000000 00000000
CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02 Checking
'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
Process timing init...done.
PCI: PCI BIOS revision 2.10 entry at 0xff8b7, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1022/2090] at 00:0f.0 Linux NET4.0 for
Linux 2.4 Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket BIOS EDD facility v0.09 2003-Jan-22, 1
devices found Starting kswapd
aio_setup: num_physpages = 32624
aio_setup: sizeof(struct page) = 52
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ
SERIAL_PCI enabled ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
lp0: using parport0 (polling).
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: Guessed IRQ 12 for device 00:10.0
PCI: Sharing IRQ 12 with 00:0f.5
eth0: Davicom DM9102 at pci00:10.0, 00:13:95:00:19:1b, irq 12.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
hda: C/H/S=0/0/0 from BIOS ignored
hda: WDC WD400VE-75HDT1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78140160 sectors (40008 MB) w/8192KiB Cache, CHSw520/16/63
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 >
SCSI subsystem driver Revision: 1.00
libata version 1.20 loaded.
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0 Freeing initrd memory: 87k
freed
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 136k freed Adding Swap: 1048568k
swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci-hcd.c: 2003-Jan-22 USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-hcd.c: block sizes: qh 128 qtd 96 itd 128 sitd 64
PCI: Guessed IRQ 12 for device 00:0f.5
PCI: Sharing IRQ 12 with 00:10.0
PCI: Setting latency timer of device 00:0f.5 to 64 ehci-hcd 00:0f.5: PCI
device 1022:2095 (Advanced Micro Devices [AMD]) ehci-hcd 00:0f.5: irq
12, pci mem 608a0000
usb.c: new USB bus registered, assigned bus number 1 ehci-hcd 00:0f.5:
ehci_start hcs_params 0x1414 dbg=0 cc=1 pcc=4 ordered ports=4 ehci-hcd
00:0f.5: ehci_start hcc_params 5012 thresh 1 uframes 256/512/1024
ehci-hcd 00:0f.5: capability 0001 at 50 ehci-hcd 00:0f.5: reset command
080002 (park)=0 ithresh=8 period\x1024 Reset HALT ehci-hcd 00:0f.5: init
command 010009 (park)=0 ithresh=1 period%6 RUN ehci-hcd 00:0f.5: USB
2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hcd.c: 00:0f.5 root hub device address 1
usb.c: kmalloc IF 4254b480, numif 1
usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Manufacturer: Linux 2.4.21-50.EL.mcut ehci-hcd
Product: PCI device 1022:2095 (Advanced Micro Devices [AMD])
SerialNumber: 00:0f.5
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: standalone hub
hub.c: individual port power switching
hub.c: individual port over-current protection
hub.c: Single TT
hub.c: TT requires at most 8 FS bit times
hub.c: Port indicators are not supported
hub.c: power on to power good time: 0ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RRRR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface 4254b480
usb.c: kusbd: /sbin/hotplug add 1
ehci-hcd 00:0f.5: GetStatus port 1 status 001803 POWER sig=j CSC
CONNECT
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 200ms ehci-hcd 00:0f.5:
port 1 high speed ehci-hcd 00:0f.5: GetStatus port 1 status 001005 POWER
sig=se0 PE CONNECT
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:0f.5-1, assigned address 2
usb.c: kmalloc IF 4254b440, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 2 default language ID 0x409
Manufacturer: USB
Product: Flash Disk
SerialNumber: 2C3F154172AC3A32
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0xea0/0x2168) is not claimed by any
active driver.
Length = 18
DescriptorType = 01
USB version = 2.00
Vendor:Product = 0ea0:2168
MaxPacketSize0 = 64
NumConfigurations = 1
Device version = 2.00
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 200mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = 08:06:50
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0002
bInterval = 01
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team ehci-hcd 00:0f.5: GetStatus
port 1 status 001002 POWER sig=se0 CSC
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
usb.c: USB disconnect on device 00:0f.5-1 address 2
usb.c: kusbd: /sbin/hotplug remove 2
ehci-hcd 00:0f.5: free_config 1 devnum 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s ehci-hcd 00:0f.5:
GetStatus port 1 status 001823 POWER sig=j OCC CSC CONNECT
hub.c: port 1, portstatus 501, change 9, 480 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 501, change 9, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 200ms ehci-hcd 00:0f.5:
port 1 high speed ehci-hcd 00:0f.5: GetStatus port 1 status 001005 POWER
sig=se0 PE CONNECT
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:0f.5-1, assigned address 3
usb.c: kmalloc IF 4254bb40, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 3 default language ID 0x409
Manufacturer: USB
Product: Flash Disk
SerialNumber: 2C3F154172AC3A32
usb.c: unhandled interfaces on device
usb.c: USB device 3 (vend/prod 0xea0/0x2168) is not claimed by any
active driver.
Length = 18
DescriptorType = 01
USB version = 2.00
Vendor:Product = 0ea0:2168
MaxPacketSize0 = 64
NumConfigurations = 1
Device version = 2.00
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 200mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = 08:06:50
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0002
bInterval = 01
usb.c: kusbd: /sbin/hotplug add 3
hub.c: port 1 over-current change
hub.c: enabling power on all ports
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 503, change 0, 480 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
=============================
/var/log/messages upon hot-plug-in of a known good device:
Target system is the Congatec ETX-LX800 (CS5536 companion), USB fails no
matter what.
===================
Aug 28 13:32:40 mcut16 kernel: hub.c: new USB device 00:0f.5-1, assigned
address 2
Aug 28 13:32:40 mcut16 kernel: Manufacturer: USB
Aug 28 13:32:40 mcut16 kernel: Product: Flash Disk
Aug 28 13:32:42 mcut16 kernel: SerialNumber: 2C3F154172AC3A32
Aug 28 13:32:42 mcut16 kernel: usb.c: USB device 2 (vend/prod
0xea0/0x2168) is not claimed by any active driver.
Aug 28 13:32:42 mcut16 kernel: Length = 18
Aug 28 13:32:42 mcut16 kernel: DescriptorType = 01
Aug 28 13:32:42 mcut16 kernel: USB version = 2.00
Aug 28 13:32:42 mcut16 kernel: Vendor:Product = 0ea0:2168
Aug 28 13:32:42 mcut16 kernel: MaxPacketSize0 = 64
Aug 28 13:32:42 mcut16 kernel: NumConfigurations = 1
Aug 28 13:32:42 mcut16 kernel: Device version = 2.00
Aug 28 13:32:42 mcut16 kernel: Device Class:SubClass:Protocol 00:00:00
Aug 28 13:32:42 mcut16 kernel: Per-interface classes
Aug 28 13:32:42 mcut16 kernel: Configuration:
Aug 28 13:32:42 mcut16 kernel: bLength = 9
Aug 28 13:32:42 mcut16 kernel: bDescriptorType = 02
Aug 28 13:32:42 mcut16 /sbin/hotplug: arguments (usb) env
(DEVFS=/proc/bus/usb OLDPWD=/ PATH=/bin:/sbin:/usr/sbin:/usr/bin
ACTIONd PWD=/etc/hotplug SHLVL=1 HOME=/ DEVICE=/proc/bus/usb/001/002
INTERFACE=8/6/80 PRODUCTê0/2168/200 TYPE=0/0/0 DEBUG=kernel
_=/bin/env)
Aug 28 13:32:42 mcut16 kernel: wTotalLength = 0027
Aug 28 13:32:42 mcut16 /sbin/hotplug: invoke etc/hotplug/usb.agent ()
Aug 28 13:32:43 mcut16 kernel: bNumInterfaces = 01
Aug 28 13:32:43 mcut16 kernel: bConfigurationValue = 01
Aug 28 13:32:43 mcut16 kernel: iConfiguration = 00
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 80
Aug 28 13:32:43 mcut16 kernel: MaxPower = 200mA
Aug 28 13:32:43 mcut16 kernel:
Aug 28 13:32:43 mcut16 kernel: Interface: 0
Aug 28 13:32:43 mcut16 kernel: Alternate Setting: 0
Aug 28 13:32:43 mcut16 kernel: bLength = 9
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 04
Aug 28 13:32:43 mcut16 kernel: bInterfaceNumber = 00
Aug 28 13:32:43 mcut16 kernel: bAlternateSetting = 00
Aug 28 13:32:43 mcut16 kernel: bNumEndpoints = 03
Aug 28 13:32:43 mcut16 kernel: bInterface Class:SubClass:Protocol 08:06:50
Aug 28 13:32:43 mcut16 kernel: iInterface = 00
Aug 28 13:32:43 mcut16 kernel: Endpoint:
Aug 28 13:32:43 mcut16 kernel: bLength = 7
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 05
Aug 28 13:32:43 mcut16 kernel: bEndpointAddress = 81 (in)
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 02 (Bulk)
Aug 28 13:32:43 mcut16 kernel: wMaxPacketSize = 0200
Aug 28 13:32:43 mcut16 kernel: bInterval = 00
Aug 28 13:32:43 mcut16 kernel: Endpoint:
Aug 28 13:32:43 mcut16 kernel: bLength = 7
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 05
Aug 28 13:32:43 mcut16 kernel: bEndpointAddress = 02 (out)
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 02 (Bulk)
Aug 28 13:32:43 mcut16 kernel: wMaxPacketSize = 0200
Aug 28 13:32:43 mcut16 kernel: bInterval = 00
Aug 28 13:32:43 mcut16 kernel: Endpoint:
Aug 28 13:32:43 mcut16 kernel: bLength = 7
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 05
Aug 28 13:32:43 mcut16 kernel: bEndpointAddress = 83 (in)
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 03(Interrupt)
Aug 28 13:32:43 mcut16 kernel: wMaxPacketSize = 0002
Aug 28 13:32:43 mcut16 kernel: bInterval = 01
===== these next two lines worry me ==============
Aug 28 13:32:43 mcut16 kernel: hub.c: port 1 over-current change
Aug 28 13:32:46 mcut16 /etc/hotplug/usb.agent: ... no modules for USB
product ea0/2168/200
*******************************************************************
*******************************************************************
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they
are addressed. If you have received this email in error please notify
the system manager.
This footnote also confirms that this email message has been swept
for the presence of computer viruses.
www.Hubbell.com - Hubbell Incorporated
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 3+ messages in thread
* USB failure (CS5536 not supported on linux 2.4.21-50?)
2007-09-10 12:56 USB failure (CS5536 not supported on linux 2.4.21-50?) Brunner, Brian T.
@ 2007-09-11 4:03 ` Brian Brunner
2007-09-11 17:46 ` Greg KH
1 sibling, 0 replies; 3+ messages in thread
From: Brian Brunner @ 2007-09-11 4:03 UTC (permalink / raw)
To: linux-hotplug
Kernel 2.4.21-50 (CentOS 3.9)
1: This kernel on EPoX EP-KRAI8 PRO recognizes all USB devices and
mounts them. HappyHappyJoyJoy. (this is my development system).
2: This kernel on Congatec ETX-LX800 with CS5536 (companion chip that
inter alia provides the USB) recognizes none (this is my product target
system).
The kernel configurator knows of CS5530 but not CS5536, I have yet to
find a kernel module for this chip/kernel combo.
I know the thumbdrive devices (and hotplug in general) are good because
of the success on the development system.
I desire clues as to what is wrong in my target system.
Here is dmesg (with thumbdrive device plugged in), and
/var/log/messages of a hotplug after the next '=='
===================================
Linux version 2.4.21-50.EL.mcut (root@mcut16) (gcc version 3.2.3
20030502 (Red Hat Linux 3.2.3-59)) #5 Fri Sep 7 08:26:35 EDT
2007 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fdc0000 (usable)
BIOS-e820: 0000000040400000 - 0000000040440004 (reserved)
BIOS-e820: 00000000f0000000 - 0000000100000000 (reserved)
509MB LOWMEM available.
NX protection not present; using segment protection On node 0
totalpages: 130496
zone(0): 4096 pages.
zone(1): 126400 pages.
zone(2): 0 pages.
Kernel command line: ro root=/dev/hda2 hdb=ide-scsi 4
ide_setup: hdb=ide-scsi
Initializing CPU#0
Detected 498.017 MHz processor.
Calibrating delay loop... 987.13 BogoMIPS Page-cache hash table entries:
131072 (order: 7, 512 KB) Page-pin hash table entries: 32768 (order: 5,
128 KB) Dentry cache hash table entries: 65536 (order: 7, 512
KB) Inode cache hash table entries: 32768 (order: 6, 256 KB)
Buffer cache hash table entries: 32768 (order: 5, 128 KB)
Memory: 508128k/521984k available (1801k kernel code, 11292k
reserved, 635k data, 136k init, 0k highmem) zapping low mappings.
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 128K (32 bytes/line)
CPU: After generic, caps: 0088a93d c0c0a13d 00000000 00000000
CPU: Common caps: 0088a93d c0c0a13d 00000000 00000000
CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02 Checking
'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
Process timing init...done.
PCI: PCI BIOS revision 2.10 entry at 0xff8b7, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1022/2090] at 00:0f.0 Linux
NET4.0 for Linux 2.4 Based upon Swansea University Computer
Society NET3.039 Initializing RT netlink socket BIOS EDD
facility v0.09 2003-Jan-22, 1 devices found Starting kswapd
aio_setup: num_physpages = 32624
aio_setup: sizeof(struct page) = 52
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS
SHARE_IRQ SERIAL_PCI enabled ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
lp0: using parport0 (polling).
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
PCI: Guessed IRQ 12 for device 00:10.0
PCI: Sharing IRQ 12 with 00:0f.5
eth0: Davicom DM9102 at pci00:10.0, 00:13:95:00:19:1b, irq 12.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
hda: C/H/S=0/0/0 from BIOS ignored
hda: WDC WD400VE-75HDT1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 78140160 sectors (40008 MB) w/8192KiB Cache, CHSw520/16/63
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 >
SCSI subsystem driver Revision: 1.00
libata version 1.20 loaded.
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0 Freeing initrd memory: 87k
freed
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 136k freed Adding Swap:
1048568k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci-hcd.c: 2003-Jan-22 USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-hcd.c: block sizes: qh 128 qtd 96 itd 128 sitd 64
PCI: Guessed IRQ 12 for device 00:0f.5
PCI: Sharing IRQ 12 with 00:10.0
PCI: Setting latency timer of device 00:0f.5 to 64 ehci-hcd
00:0f.5: PCI device 1022:2095 (Advanced Micro Devices [AMD]) ehci-hcd
00:0f.5: irq 12, pci mem 608a0000
usb.c: new USB bus registered, assigned bus number 1 ehci-hcd
00:0f.5: ehci_start hcs_params 0x1414 dbg=0 cc=1 pcc=4 ordered ports=4
ehci-hcd
00:0f.5: ehci_start hcc_params 5012 thresh 1 uframes 256/512/1024
ehci-hcd
00:0f.5: capability 0001 at 50 ehci-hcd
00:0f.5: reset command 080002 (park)=0 ithresh=8 period\x1024 Reset HALT
ehci-hcd
00:0f.5: init command 010009 (park)=0 ithresh=1 period%6 RUN ehci-hcd
00:0f.5: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hcd.c: 00:0f.5 root hub device address 1
usb.c: kmalloc IF 4254b480, numif 1
usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Manufacturer: Linux 2.4.21-50.EL.mcut ehci-hcd
Product: PCI device 1022:2095 (Advanced Micro Devices [AMD])
SerialNumber: 00:0f.5
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: standalone hub
hub.c: individual port power switching
hub.c: individual port over-current protection
hub.c: Single TT
hub.c: TT requires at most 8 FS bit times
hub.c: Port indicators are not supported
hub.c: power on to power good time: 0ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RRRR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface 4254b480
usb.c: kusbd: /sbin/hotplug add 1
ehci-hcd 00:0f.5: GetStatus port 1 status 001803 POWER sig=j
CSC CONNECT
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 501, change 1, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 200ms ehci-hcd 00:0f.5:
port 1 high speed ehci-hcd 00:0f.5: GetStatus port 1 status 001005 POWER
sig=se0 PE CONNECT
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:0f.5-1, assigned address 2
usb.c: kmalloc IF 4254b440, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 2 default language ID 0x409
Manufacturer: USB
Product: Flash Disk
SerialNumber: 2C3F154172AC3A32
usb.c: unhandled interfaces on device
usb.c: USB device 2 (vend/prod 0xea0/0x2168) is not claimed
by any active driver.
Length = 18
DescriptorType = 01
USB version = 2.00
Vendor:Product = 0ea0:2168
MaxPacketSize0 = 64
NumConfigurations = 1
Device version = 2.00
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 200mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = 08:06:50
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0002
bInterval = 01
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal
journal kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team ehci-hcd
00:0f.5: GetStatus port 1 status 001002 POWER sig=se0 CSC
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
usb.c: USB disconnect on device 00:0f.5-1 address 2
usb.c: kusbd: /sbin/hotplug remove 2
ehci-hcd 00:0f.5: free_config 1 devnum 2
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s ehci-hcd 00:0f.5:
GetStatus port 1 status 001823 POWER sig=j OCC CSC CONNECT
hub.c: port 1, portstatus 501, change 9, 480 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 501, change 9, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 501, change 0, 480 Mb/s
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 10ms
hub.c: port 1, portstatus 511, change 0, 480 Mb/s
hub.c: port 1 of hub 1 not reset yet, waiting 200ms ehci-hcd 00:0f.5:
port 1 high speed ehci-hcd 00:0f.5: GetStatus port 1 status 001005 POWER
sig=se0 PE CONNECT
hub.c: port 1, portstatus 503, change 10, 480 Mb/s
hub.c: new USB device 00:0f.5-1, assigned address 3
usb.c: kmalloc IF 4254bb40, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 3 default language ID 0x409
Manufacturer: USB
Product: Flash Disk
SerialNumber: 2C3F154172AC3A32
usb.c: unhandled interfaces on device
usb.c: USB device 3 (vend/prod 0xea0/0x2168) is not claimed
by any active driver.
Length = 18
DescriptorType = 01
USB version = 2.00
Vendor:Product = 0ea0:2168
MaxPacketSize0 = 64
NumConfigurations = 1
Device version = 2.00
Device Class:SubClass:Protocol = 00:00:00
Per-interface classes
Configuration:
bLength = 9
bDescriptorType = 02
wTotalLength = 0027
bNumInterfaces = 01
bConfigurationValue = 01
iConfiguration = 00
bmAttributes = 80
MaxPower = 200mA
Interface: 0
Alternate Setting: 0
bLength = 9
bDescriptorType = 04
bInterfaceNumber = 00
bAlternateSetting = 00
bNumEndpoints = 03
bInterface Class:SubClass:Protocol = 08:06:50
iInterface = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 81 (in)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 02 (out)
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0200
bInterval = 00
Endpoint:
bLength = 7
bDescriptorType = 05
bEndpointAddress = 83 (in)
bmAttributes = 03 (Interrupt)
wMaxPacketSize = 0002
bInterval = 01
usb.c: kusbd: /sbin/hotplug add 3
hub.c: port 1 over-current change
hub.c: enabling power on all ports
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 503, change 0, 480 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 3, portstatus 100, change 0, 12 Mb/s
hub.c: port 4, portstatus 100, change 0, 12 Mb/s
=============================
/var/log/messages upon hot-plug-in of a known good device:
Target system is the Congatec ETX-LX800 (CS5536 companion),
USB fails no matter what.
===================
Aug 28 13:32:40 mcut16 kernel: hub.c: new USB device 00:0f.5-1, assigned
address 2
Aug 28 13:32:40 mcut16 kernel: Manufacturer: USB
Aug 28 13:32:40 mcut16 kernel: Product: Flash Disk
Aug 28 13:32:42 mcut16 kernel: SerialNumber: 2C3F154172AC3A32
Aug 28 13:32:42 mcut16 kernel: usb.c: USB device 2 (vend/prod
0xea0/0x2168) is not claimed by any active driver.
Aug 28 13:32:42 mcut16 kernel: Length = 18
Aug 28 13:32:42 mcut16 kernel: DescriptorType = 01
Aug 28 13:32:42 mcut16 kernel: USB version = 2.00
Aug 28 13:32:42 mcut16 kernel: Vendor:Product = 0ea0:2168
Aug 28 13:32:42 mcut16 kernel: MaxPacketSize0 = 64
Aug 28 13:32:42 mcut16 kernel: NumConfigurations = 1
Aug 28 13:32:42 mcut16 kernel: Device version = 2.00
Aug 28 13:32:42 mcut16 kernel: Device Class:SubClass:Protocol 00:00:00
Aug 28 13:32:42 mcut16 kernel: Per-interface classes
Aug 28 13:32:42 mcut16 kernel: Configuration:
Aug 28 13:32:42 mcut16 kernel: bLength = 9
Aug 28 13:32:42 mcut16 kernel: bDescriptorType = 02
Aug 28 13:32:42 mcut16 /sbin/hotplug: arguments (usb) env
(DEVFS=/proc/bus/usb OLDPWD=/ PATH=/bin:/sbin:/usr/sbin:/usr/bin
ACTIONd PWD=/etc/hotplug SHLVL=1 HOME=/
DEVICE=/proc/bus/usb/001/002 INTERFACE=8/6/80
PRODUCTê0/2168/200 TYPE=0/0/0 DEBUG=kernel
_=/bin/env)
Aug 28 13:32:42 mcut16 kernel: wTotalLength = 0027
Aug 28 13:32:42 mcut16 /sbin/hotplug: invoke etc/hotplug/usb.agent ()
Aug 28 13:32:43 mcut16 kernel: bNumInterfaces = 01
Aug 28 13:32:43 mcut16 kernel: bConfigurationValue = 01
Aug 28 13:32:43 mcut16 kernel: iConfiguration = 00
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 80
Aug 28 13:32:43 mcut16 kernel: MaxPower = 200mA
Aug 28 13:32:43 mcut16 kernel:
Aug 28 13:32:43 mcut16 kernel: Interface: 0
Aug 28 13:32:43 mcut16 kernel: Alternate Setting: 0
Aug 28 13:32:43 mcut16 kernel: bLength = 9
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 04
Aug 28 13:32:43 mcut16 kernel: bInterfaceNumber = 00
Aug 28 13:32:43 mcut16 kernel: bAlternateSetting = 00
Aug 28 13:32:43 mcut16 kernel: bNumEndpoints = 03
Aug 28 13:32:43 mcut16 kernel: bInterface Class:SubClass:Protocol 08:06:50
Aug 28 13:32:43 mcut16 kernel: iInterface = 00
Aug 28 13:32:43 mcut16 kernel: Endpoint:
Aug 28 13:32:43 mcut16 kernel: bLength = 7
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 05
Aug 28 13:32:43 mcut16 kernel: bEndpointAddress = 81 (in)
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 02 (Bulk)
Aug 28 13:32:43 mcut16 kernel: wMaxPacketSize = 0200
Aug 28 13:32:43 mcut16 kernel: bInterval = 00
Aug 28 13:32:43 mcut16 kernel: Endpoint:
Aug 28 13:32:43 mcut16 kernel: bLength = 7
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 05
Aug 28 13:32:43 mcut16 kernel: bEndpointAddress = 02 (out)
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 02 (Bulk)
Aug 28 13:32:43 mcut16 kernel: wMaxPacketSize = 0200
Aug 28 13:32:43 mcut16 kernel: bInterval = 00
Aug 28 13:32:43 mcut16 kernel: Endpoint:
Aug 28 13:32:43 mcut16 kernel: bLength = 7
Aug 28 13:32:43 mcut16 kernel: bDescriptorType = 05
Aug 28 13:32:43 mcut16 kernel: bEndpointAddress = 83 (in)
Aug 28 13:32:43 mcut16 kernel: bmAttributes = 03(Interrupt)
Aug 28 13:32:43 mcut16 kernel: wMaxPacketSize = 0002
Aug 28 13:32:43 mcut16 kernel: bInterval = 01
===== these next two lines worry me ==============
Aug 28 13:32:43 mcut16 kernel: hub.c: port 1 over-current change
Aug 28 13:32:46 mcut16 /etc/hotplug/usb.agent: ... no modules for USB
product ea0/2168/200
*******************************************************************
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: USB failure (CS5536 not supported on linux 2.4.21-50?)
2007-09-10 12:56 USB failure (CS5536 not supported on linux 2.4.21-50?) Brunner, Brian T.
2007-09-11 4:03 ` Brian Brunner
@ 2007-09-11 17:46 ` Greg KH
1 sibling, 0 replies; 3+ messages in thread
From: Greg KH @ 2007-09-11 17:46 UTC (permalink / raw)
To: linux-hotplug
On Tue, Sep 11, 2007 at 12:03:30AM -0400, Brian Brunner wrote:
>
> Kernel 2.4.21-50 (CentOS 3.9)
Please ask for support for such an old kernel on the centos mailing
lists, there is no one in this community that supports such an old
kernel anymore, sorry.
good luck,
greg k-h
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2007-09-11 17:46 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-09-10 12:56 USB failure (CS5536 not supported on linux 2.4.21-50?) Brunner, Brian T.
2007-09-11 4:03 ` Brian Brunner
2007-09-11 17:46 ` Greg KH
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).