* how to rename network interface?
@ 2004-05-09 18:24 mikep
2004-05-10 2:05 ` Kay Sievers
` (3 more replies)
0 siblings, 4 replies; 5+ messages in thread
From: mikep @ 2004-05-09 18:24 UTC (permalink / raw)
To: linux-hotplug
Using udev-025 i am trying to rename eth0 with these rules in 50-udev.rules:
BUS="pci", SYSFS{device}="0x8169", NAME="eth0"
BUS="pci", SYSFS{device}="0x8139", NAME="eth1"
udev-logging doesn't show any errors.
-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to
deliver higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: how to rename network interface?
2004-05-09 18:24 how to rename network interface? mikep
@ 2004-05-10 2:05 ` Kay Sievers
2004-05-10 11:30 ` mikep
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Kay Sievers @ 2004-05-10 2:05 UTC (permalink / raw)
To: linux-hotplug
On Sun, 2004-05-09 at 14:24 -0400, mikep wrote:
> Using udev-025 i am trying to rename eth0 with these rules in 50-udev.rules:
>
> BUS="pci", SYSFS{device}="0x8169", NAME="eth0"
> BUS="pci", SYSFS{device}="0x8139", NAME="eth1"
What does udevinfo show?
udevinfo -p /class/net/eth0 -a
> udev-logging doesn't show any errors.
You need to compile it with 'make DEBUG=true' to get a very detailed
log.
good luck,
Kay
-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to
deliver higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: how to rename network interface?
2004-05-09 18:24 how to rename network interface? mikep
2004-05-10 2:05 ` Kay Sievers
@ 2004-05-10 11:30 ` mikep
2004-05-10 12:41 ` mikep
2004-05-11 10:41 ` Kay Sievers
3 siblings, 0 replies; 5+ messages in thread
From: mikep @ 2004-05-10 11:30 UTC (permalink / raw)
To: linux-hotplug
Kay Sievers wrote:
> On Sun, 2004-05-09 at 14:24 -0400, mikep wrote:
>
>>Using udev-025 i am trying to rename eth0 with these rules in 50-udev.rules:
>>
>>BUS="pci", SYSFS{device}="0x8169", NAME="eth0"
>>BUS="pci", SYSFS{device}="0x8139", NAME="eth1"
>
>
> What does udevinfo show?
> udevinfo -p /class/net/eth0 -a
>
7:16 >>udevinfo -p /class/net/eth0 -a
looking at class device '/sys/class/net/eth0':
SYSFS{addr_len}="6"
SYSFS{address}="00:01:0a:10:a7:3b"
SYSFS{broadcast}="ff:ff:ff:ff:ff:ff"
SYSFS{features}="0x29"
SYSFS{flags}="0x1003"
SYSFS{ifindex}="2"
SYSFS{iflink}="2"
SYSFS{mtu}="1500"
SYSFS{tx_queue_len}="1000"
SYSFS{type}="1"
follow the class device's "device"
looking at the device chain at
'/sys/devices/pci0000:00/0000:00:08.0/0000:01:07.0':
BUS="pci"
ID="0000:01:07.0"
SYSFS{class}="0x020000"
SYSFS{detach_state}="0"
SYSFS{device}="0x8139"
SYSFS{irq}="5"
SYSFS{subsystem_device}="0x8139"
SYSFS{subsystem_vendor}="0x1436"
SYSFS{vendor}="0x10ec"
looking at the device chain at '/sys/devices/pci0000:00/0000:00:08.0':
BUS="pci"
ID="0000:00:08.0"
SYSFS{class}="0x060400"
SYSFS{detach_state}="0"
SYSFS{device}="0x006c"
SYSFS{irq}="0"
SYSFS{subsystem_device}="0x0000"
SYSFS{subsystem_vendor}="0x0000"
SYSFS{vendor}="0x10de"
looking at the device chain at '/sys/devices/pci0000:00':
BUS=""
ID="pci0000:00"
SYSFS{detach_state}="0"
And udevinfo for eth1 shows:
looking at class device '/sys/class/net/eth1':
SYSFS{addr_len}="6"
SYSFS{address}="00:08:54:d1:a0:d5"
SYSFS{broadcast}="ff:ff:ff:ff:ff:ff"
SYSFS{features}="0x0"
SYSFS{flags}="0x1002"
SYSFS{ifindex}="3"
SYSFS{iflink}="3"
SYSFS{mtu}="1500"
SYSFS{tx_queue_len}="1000"
SYSFS{type}="1"
follow the class device's "device"
looking at the device chain at
'/sys/devices/pci0000:00/0000:00:08.0/0000:01:08.0':
BUS="pci"
ID="0000:01:08.0"
SYSFS{class}="0x020000"
SYSFS{detach_state}="0"
SYSFS{device}="0x8169"
SYSFS{irq}="11"
SYSFS{subsystem_device}="0x8169"
......................................
I also tried these rules without success:
KERNEL="eth*", SYSFS{address}="00:08:54:d1:a0:d5", NAME="eth0"
KERNEL="eth*", SYSFS{address}="00:01:0a:10:a7:3b", NAME="eth1"
If i use 'nameif' in the hotplug script net.agent it works. But i prefer
to rename the interface by device type rather than address.
-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to
deliver higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: how to rename network interface?
2004-05-09 18:24 how to rename network interface? mikep
2004-05-10 2:05 ` Kay Sievers
2004-05-10 11:30 ` mikep
@ 2004-05-10 12:41 ` mikep
2004-05-11 10:41 ` Kay Sievers
3 siblings, 0 replies; 5+ messages in thread
From: mikep @ 2004-05-10 12:41 UTC (permalink / raw)
To: linux-hotplug
mikep wrote:
> Kay Sievers wrote:
>
>> On Sun, 2004-05-09 at 14:24 -0400, mikep wrote:
>>
>>> Using udev-025 i am trying to rename eth0 with these rules in
>>> 50-udev.rules:
>>>
>>> BUS="pci", SYSFS{device}="0x8169", NAME="eth0"
>>> BUS="pci", SYSFS{device}="0x8139", NAME="eth1"
>>
>>
>>
>> What does udevinfo show?
>> udevinfo -p /class/net/eth0 -a
>>
> 7:16 >>udevinfo -p /class/net/eth0 -a
>
> looking at class device '/sys/class/net/eth0':
> SYSFS{addr_len}="6"
> SYSFS{address}="00:01:0a:10:a7:3b"
> SYSFS{broadcast}="ff:ff:ff:ff:ff:ff"
> SYSFS{features}="0x29"
> SYSFS{flags}="0x1003"
> SYSFS{ifindex}="2"
> SYSFS{iflink}="2"
> SYSFS{mtu}="1500"
> SYSFS{tx_queue_len}="1000"
> SYSFS{type}="1"
>
> follow the class device's "device"
> looking at the device chain at
> '/sys/devices/pci0000:00/0000:00:08.0/0000:01:07.0':
> BUS="pci"
> ID="0000:01:07.0"
> SYSFS{class}="0x020000"
> SYSFS{detach_state}="0"
> SYSFS{device}="0x8139"
> SYSFS{irq}="5"
> SYSFS{subsystem_device}="0x8139"
> SYSFS{subsystem_vendor}="0x1436"
> SYSFS{vendor}="0x10ec"
>
> looking at the device chain at '/sys/devices/pci0000:00/0000:00:08.0':
> BUS="pci"
> ID="0000:00:08.0"
> SYSFS{class}="0x060400"
> SYSFS{detach_state}="0"
> SYSFS{device}="0x006c"
> SYSFS{irq}="0"
> SYSFS{subsystem_device}="0x0000"
> SYSFS{subsystem_vendor}="0x0000"
> SYSFS{vendor}="0x10de"
>
> looking at the device chain at '/sys/devices/pci0000:00':
> BUS=""
> ID="pci0000:00"
> SYSFS{detach_state}="0"
>
> And udevinfo for eth1 shows:
>
> looking at class device '/sys/class/net/eth1':
> SYSFS{addr_len}="6"
> SYSFS{address}="00:08:54:d1:a0:d5"
> SYSFS{broadcast}="ff:ff:ff:ff:ff:ff"
> SYSFS{features}="0x0"
> SYSFS{flags}="0x1002"
> SYSFS{ifindex}="3"
> SYSFS{iflink}="3"
> SYSFS{mtu}="1500"
> SYSFS{tx_queue_len}="1000"
> SYSFS{type}="1"
>
> follow the class device's "device"
> looking at the device chain at
> '/sys/devices/pci0000:00/0000:00:08.0/0000:01:08.0':
> BUS="pci"
> ID="0000:01:08.0"
> SYSFS{class}="0x020000"
> SYSFS{detach_state}="0"
> SYSFS{device}="0x8169"
> SYSFS{irq}="11"
> SYSFS{subsystem_device}="0x8169"
> ......................................
> I also tried these rules without success:
>
> KERNEL="eth*", SYSFS{address}="00:08:54:d1:a0:d5", NAME="eth0"
> KERNEL="eth*", SYSFS{address}="00:01:0a:10:a7:3b", NAME="eth1"
>
> If i use 'nameif' in the hotplug script net.agent it works. But i prefer
> to rename the interface by device type rather than address.
>
Some more info as I added the rules to a new file: 10-udev.rules
##Rename network interfaces
BUS="pci", SYSFS{device}="0x8169", NAME="eth0"
BUS="pci", SYSFS{device}="0x8139", NAME="eth1"
KERNEL="eth*", SYSFS{address}="00:08:54:d1:a0:d5", NAME="eth0"
KERNEL="eth*", SYSFS{address}="00:01:0a:10:a7:3b", NAME="eth1"
and syslog shows that the rules are applied:
udev[7620]: configured rule in '/etc/udev/rules.d//10-udev.rules' at
line 3 applied, 'eth0' becomes 'eth1'
udev[7621]: configured rule in '/etc/udev/rules.d//10-udev.rules' at
line 2 applied, 'eth1' becomes 'eth0'
However, the end result is that device 0x8139 is still configured as
eth0 as ifconfig shows:
>>ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:01:0A:10:A7:3B
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
.....................
I am using Gentoo linux.
-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to
deliver higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: how to rename network interface?
2004-05-09 18:24 how to rename network interface? mikep
` (2 preceding siblings ...)
2004-05-10 12:41 ` mikep
@ 2004-05-11 10:41 ` Kay Sievers
3 siblings, 0 replies; 5+ messages in thread
From: Kay Sievers @ 2004-05-11 10:41 UTC (permalink / raw)
To: linux-hotplug
On Mon, May 10, 2004 at 08:41:39AM -0400, mikep wrote:
> and syslog shows that the rules are applied:
>
> udev[7620]: configured rule in '/etc/udev/rules.d//10-udev.rules' at
> line 3 applied, 'eth0' becomes 'eth1'
>
> udev[7621]: configured rule in '/etc/udev/rules.d//10-udev.rules' at
> line 2 applied, 'eth1' becomes 'eth0'
>
> However, the end result is that device 0x8139 is still configured as
> eth0 as ifconfig shows:
Are you sure the the interface is not in use, while udev tries to rename
it. Maybe your network script is faster than udev?
Kay
> >>ifconfig eth0
> eth0 Link encap:Ethernet HWaddr 00:01:0A:10:A7:3B
> inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
-------------------------------------------------------
This SF.Net email is sponsored by Sleepycat Software
Learn developer strategies Cisco, Motorola, Ericsson & Lucent use to
deliver higher performing products faster, at low TCO.
http://www.sleepycat.com/telcomwpreg.php?From=osdnemail3
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2004-05-11 10:41 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-05-09 18:24 how to rename network interface? mikep
2004-05-10 2:05 ` Kay Sievers
2004-05-10 11:30 ` mikep
2004-05-10 12:41 ` mikep
2004-05-11 10:41 ` Kay Sievers
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).