# cardctl ident 1 product info: "3Com Corporation", "3C562D/3C563D", "EtherLink III", "LAN+Modem PC Card" manfid: 0x0101, 0x0562 function: 6 (network) # /etc/init.d/pcmcia start PCIC=yenta_socket Starting PCMCIA services: modulesJun 29 08:31:03 koala kernel: Linux PCMCIA Card Services 3.1.22 Jun 29 08:31:03 koala kernel: options: [pci] [cardbus] [pm] Jun 29 08:31:04 koala kernel: PCI: Found IRQ 11 for device 00:11.0 Jun 29 08:31:04 koala kernel: PCI: The same IRQ used for device 00:11.1 Jun 29 08:31:04 koala kernel: PCI: Found IRQ 11 for device 00:11.1 Jun 29 08:31:04 koala kernel: PCI: The same IRQ used for device 00:11.0 Jun 29 08:31:04 koala kernel: Yenta IRQ list 06d8, PCI irq11 Jun 29 08:31:04 koala kernel: Socket status: 30000006 Jun 29 08:31:04 koala kernel: Yenta IRQ list 06d8, PCI irq11 Jun 29 08:31:04 koala kernel: Socket status: 30000010 cardmgr. koala:~/knl/240# Jun 29 08:31:04 koala cardmgr[1363]: starting, version is 3.1.25 Jun 29 08:31:04 koala cardmgr[1363]: watching 2 sockets Jun 29 08:31:04 koala cardmgr[1363]: Card Services release does not match Jun 29 08:31:04 koala kernel: cs: IO port probe 0x0c00-0x0cff: clean. Jun 29 08:31:04 koala kernel: cs: IO port probe 0x0800-0x08ff: clean. Jun 29 08:31:04 koala kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x250-0x257 0x260-0x267 0x330-0x337 0x378-0x37f 0x388-0x38f 0x3f8-0x3ff 0x4d0-0x4d7 Jun 29 08:31:04 koala kernel: cs: IO port probe 0x0a00-0x0aff: clean. Jun 29 08:31:04 koala cardmgr[1363]: initializing socket 1 Jun 29 08:31:04 koala kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. Jun 29 08:31:04 koala cardmgr[1363]: socket 1: 3Com 3c562/3c563 Ethernet/Modem Jun 29 08:31:05 koala cardmgr[1363]: executing: 'modprobe 3c589_cs' Jun 29 08:31:05 koala cardmgr[1363]: executing: 'modprobe serial_cs' Jun 29 08:31:05 koala kernel: isapnp: Scanning for PnP cards... Jun 29 08:31:05 koala kernel: isapnp: No Plug & Play device found Jun 29 08:31:05 koala kernel: Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled Jun 29 08:31:05 koala kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A Jun 29 08:31:06 koala cardmgr[1363]: executing: './network start eth0' Jun 29 08:31:06 koala kernel: eth0: 3Com 3c562, io 0x300, irq 3, hw_addr 00:60:97:F8:8B:52Jun 29 08:31:06 koala kernel: 8K FIFO split 5:3 Rx:Tx, auto xcvr Jun 29 08:31:06 koala kernel: ttyS01 at port 0x02f8 (irq = 3) is a 16550A Jun 29 08:31:06 koala cardmgr[1363]: executing: './serial start ttyS1' Jun 29 08:31:07 koala kernel: eth0: flipped to 10baseT # lsmod Module Size Used by serial_cs 4576 0 (unused) serial 43280 0 [serial_cs] isa-pnp 27888 0 [serial] 3c589_cs 7760 1 ds 6560 2 [serial_cs 3c589_cs] yenta_socket 8688 2 pcmcia_core 39360 0 [serial_cs 3c589_cs ds yenta_socket] 3c59x 23968 0 rtc 5376 0 (autoclean) # ifconfig eth0 Link encap:Ethernet HWaddr 00:60:97:F8:8B:52 inet addr:192.73.213.72 Bcast:192.73.213.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1537 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:587705 (573.9 Kb) TX bytes:0 (0.0 b) Interrupt:3 Base address:0x300 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:78 errors:0 dropped:0 overruns:0 frame:0 TX packets:78 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4972 (4.8 Kb) TX bytes:4972 (4.8 Kb) koala:~/knl/240# ping corel.com PING corel.com (206.47.20.65): 56 data bytes 64 bytes from 206.47.20.65: icmp_seq=0 ttl=47 time=147.7 ms 64 bytes from 206.47.20.65: icmp_seq=1 ttl=47 time=145.9 ms --- corel.com ping statistics --- 2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 145.9/146.8/147.7 ms ============= Rebooting with 3Com PCI 3CCFE575BT Cyclone CardBus in the PCMCIA socket, dmesg reports: Linux PCMCIA Card Services 3.1.22 options: [pci] [cardbus] [pm] PCI: Found IRQ 11 for device 00:11.0 PCI: The same IRQ used for device 00:11.1 PCI: Found IRQ 11 for device 00:11.1 PCI: The same IRQ used for device 00:11.0 Yenta IRQ list 0698, PCI irq11 Socket status: 30000006 Yenta IRQ list 0698, PCI irq11 Socket status: 30000020 cs: cb_alloc(bus 2): vendor 0x10b7, device 0x5157 got res[1c00:1c7f] for resource 0 of PCI device 10b7:5157 got res[10c00000:10c0007f] for resource 1 of PCI device 10b7:5157 got res[10c00080:10c000ff] for resource 2 of PCI device 10b7:5157 got res[10800000:1081ffff] for resource 6 of PCI device 10b7:5157 PCI: Enabling device 02:00.0 (0000 -> 0003) cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0800-0x08ff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x250-0x257 0x260-0x267 0x330-0x337 0x378-0x37f 0x388-0x38f 0x3f8-0x3ff 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. 3c59x.c:LK1.1.13 27 Jan 2001 Donald Becker and others. http://www.scyld.com/network/vortex.html See Documentation/networking/vortex.txt eth0: 3Com PCI 3CCFE575BT Cyclone CardBus at 0x1c00, PCI: Setting latency timer of device 02:00.0 to 64 00:10:4b:f8:71:22, IRQ 11 product code 4e56 rev 07.1 date 01-17-99 eth0: CardBus functions mapped 10c00080->c4832080 8K byte-wide RAM 5:3 Rx:Tx split, MII interface. MII transceiver found at address 0, status 782d. Enabling bus-master transmits and whole-frame receives. eth0: scatter/gather enabled. h/w checksums enabled # lsmod Module Size Used by 3c59x 23968 1 ds 6560 2 yenta_socket 8688 2 pcmcia_core 39360 0 [ds yenta_socket] rtc 5376 0 (autoclean) There is only one beep from the card and: ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:65 errors:0 dropped:0 overruns:0 frame:0 TX packets:65 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4384 (4.2 Kb) TX bytes:4384 (4.2 Kb) koala:~/knl/240# ifconfig eth0 up koala:~/knl/240# Jun 29 08:50:51 koala kernel: eth0: using default media MII koala:~/knl/240# ifconfig eth0 Link encap:Ethernet HWaddr 00:10:4B:F8:71:22 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:25 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:13184 (12.8 Kb) TX bytes:0 (0.0 b) Interrupt:11 Base address:0x1c00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:65 errors:0 dropped:0 overruns:0 frame:0 TX packets:65 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4384 (4.2 Kb) TX bytes:4384 (4.2 Kb) koala:~/knl/240# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 127.0.0.0 * 255.0.0.0 U 0 0 0 lo Thus with this card, the eth0 is not being established. Any suggestions? What is the significance of : eth0: using default media MII MarvS