[PATCH v2] hwmon: (adm1275): Add device tree param for shunt resistor

[Kun Yi <kunyi@google.com>]

The ADM series of hotswap controllers support extending
the current measurement range by using a sensing resistor
value other than the typical 1 mOhm. For example, using a 0.5 mOhm
sensing resistor doubles the maximal current can be measured.

Current driver assumes a shunt resistor value of 1 mOhm in calculation,
meaning for other resistor values, hwmon will report scaled
current/power measurements. This patch adds a device tree parameter so
that individual boards can configure its shunt resistor value.

Signed-off-by: Kun Yi <kunyi@google.com>
---
 .../devicetree/bindings/hwmon/adm1275.txt     | 25 +++++++++++++++++++
 Documentation/hwmon/adm1275                   |  3 +++
 drivers/hwmon/pmbus/adm1275.c                 | 15 +++++++++--
 3 files changed, 41 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/hwmon/adm1275.txt

diff --git a/Documentation/devicetree/bindings/hwmon/adm1275.txt b/Documentation/devicetree/bindings/hwmon/adm1275.txt
new file mode 100644
index 000000000000..1ecd03f3da4d
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/adm1275.txt
@@ -0,0 +1,25 @@
+adm1275 properties
+
+Required properties:
+- compatible: Must be one of the supported compatible strings:
+	- "adi,adm1075" for adm1075
+	- "adi,adm1272" for adm1272
+	- "adi,adm1275" for adm1275
+	- "adi,adm1276" for adm1276
+	- "adi,adm1278" for adm1278
+	- "adi,adm1293" for adm1293
+	- "adi,adm1294" for adm1294
+- reg: I2C address
+
+Optional properties:
+
+- shunt-resistor-micro-ohms
+	Shunt resistor value in micro-Ohm
+
+Example:
+
+adm1272@10 {
+	compatible = "adi,adm1272";
+	reg = <0x10>;
+	shunt-resistor-micro-ohms = <500>;
+};
diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275
index 39033538eb03..5e277b0d91ce 100644
--- a/Documentation/hwmon/adm1275
+++ b/Documentation/hwmon/adm1275
@@ -58,6 +58,9 @@ The ADM1075, unlike many other PMBus devices, does not support internal voltage
 or current scaling. Reported voltages, currents, and power are raw measurements,
 and will typically have to be scaled.
 
+The shunt value in micro-ohms can be set via device tree at compile-time. Please
+refer to the Documentation/devicetree/bindings/hwmon/adm1275.txt for bindings
+if the device tree is used.
 
 Platform data support
 ---------------------
diff --git a/drivers/hwmon/pmbus/adm1275.c b/drivers/hwmon/pmbus/adm1275.c
index 13600fa79e7f..f569372c9204 100644
--- a/drivers/hwmon/pmbus/adm1275.c
+++ b/drivers/hwmon/pmbus/adm1275.c
@@ -373,6 +373,7 @@ static int adm1275_probe(struct i2c_client *client,
 	const struct coefficients *coefficients;
 	int vindex = -1, voindex = -1, cindex = -1, pindex = -1;
 	int tindex = -1;
+	u32 shunt;
 
 	if (!i2c_check_functionality(client->adapter,
 				     I2C_FUNC_SMBUS_READ_BYTE_DATA
@@ -421,6 +422,13 @@ static int adm1275_probe(struct i2c_client *client,
 	if (!data)
 		return -ENOMEM;
 
+	if (of_property_read_u32(client->dev.of_node,
+				 "shunt-resistor-micro-ohms", &shunt))
+		shunt = 1000; /* 1 mOhm if not set via DT */
+
+	if (shunt == 0)
+		return -EINVAL;
+
 	data->id = mid->driver_data;
 
 	info = &data->info;
@@ -654,12 +662,15 @@ static int adm1275_probe(struct i2c_client *client,
 		info->R[PSC_VOLTAGE_OUT] = coefficients[voindex].R;
 	}
 	if (cindex >= 0) {
-		info->m[PSC_CURRENT_OUT] = coefficients[cindex].m;
+		/* Scale current with sense resistor value */
+		info->m[PSC_CURRENT_OUT] =
+			coefficients[cindex].m * shunt / 1000;
 		info->b[PSC_CURRENT_OUT] = coefficients[cindex].b;
 		info->R[PSC_CURRENT_OUT] = coefficients[cindex].R;
 	}
 	if (pindex >= 0) {
-		info->m[PSC_POWER] = coefficients[pindex].m;
+		info->m[PSC_POWER] =
+			coefficients[pindex].m * shunt / 1000;
 		info->b[PSC_POWER] = coefficients[pindex].b;
 		info->R[PSC_POWER] = coefficients[pindex].R;
 	}
-- 
2.19.0.605.g01d371f741-goog