From: Daniel Matyas <daniel.matyas@analog.com>
To: unlisted-recipients:; (no To-header on input)
Cc: Daniel Matyas <daniel.matyas@analog.com>,
Jean Delvare <jdelvare@suse.com>,
Guenter Roeck <linux@roeck-us.net>,
Jonathan Corbet <corbet@lwn.net>, <linux-hwmon@vger.kernel.org>,
<linux-doc@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v6 2/5] hwmon: max31827: Add support for max31828 and max31829
Date: Tue, 31 Oct 2023 20:21:54 +0200 [thread overview]
Message-ID: <20231031182158.124608-2-daniel.matyas@analog.com> (raw)
In-Reply-To: <20231031182158.124608-1-daniel.matyas@analog.com>
Created of_match_table and id_table entries for max31828 and max31829.
When adi,flt-q and/or adi,alrm-pol are not mentioned,
the default configuration is loaded based on the type of the chip.
Signed-off-by: Daniel Matyas <daniel.matyas@analog.com>
---
v5 -> v6: Selecting default value for adi,fault-q and adi,alarm-pol with
switch() statement. Used device_get_match_data() to get data more
generally. Now max31827 = 1 in enum.
v4 -> v5: Passed i2c_client to init_client(), because I needed it to
retrieve device id.
Used a simple if to load default configuration. No more switch.
v3 -> v4: No change.
v3: Added patch.
drivers/hwmon/max31827.c | 64 +++++++++++++++++++++++++++++++++-------
1 file changed, 53 insertions(+), 11 deletions(-)
diff --git a/drivers/hwmon/max31827.c b/drivers/hwmon/max31827.c
index bc201a8fcd5b..738ce5ca6e39 100644
--- a/drivers/hwmon/max31827.c
+++ b/drivers/hwmon/max31827.c
@@ -32,7 +32,9 @@
#define MAX31827_CONFIGURATION_O_TEMP_STAT_MASK BIT(15)
#define MAX31827_ALRM_POL_LOW 0x0
+#define MAX31827_ALRM_POL_HIGH 0x1
#define MAX31827_FLT_Q_1 0x0
+#define MAX31827_FLT_Q_4 0x2
#define MAX31827_12_BIT_CNV_TIME 140
@@ -40,6 +42,8 @@
#define MAX31827_M_DGR_TO_16_BIT(x) (((x) << 4) / 1000)
#define MAX31827_DEVICE_ENABLE(x) ((x) ? 0xA : 0x0)
+enum chips { max31827 = 1, max31828, max31829 };
+
enum max31827_cnv {
MAX31827_CNV_1_DIV_64_HZ = 1,
MAX31827_CNV_1_DIV_32_HZ,
@@ -370,12 +374,21 @@ static int max31827_write(struct device *dev, enum hwmon_sensor_types type,
return -EOPNOTSUPP;
}
+static const struct i2c_device_id max31827_i2c_ids[] = {
+ { "max31827", max31827 },
+ { "max31828", max31828 },
+ { "max31829", max31829 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, max31827_i2c_ids);
+
static int max31827_init_client(struct max31827_state *st,
struct device *dev)
{
struct fwnode_handle *fwnode;
unsigned int res = 0;
u32 data, lsb_idx;
+ enum chips type;
bool prop;
int ret;
@@ -392,6 +405,8 @@ static int max31827_init_client(struct max31827_state *st,
prop = fwnode_property_read_bool(fwnode, "adi,timeout-enable");
res |= FIELD_PREP(MAX31827_CONFIGURATION_TIMEOUT_MASK, !prop);
+ type = (enum chips)(uintptr_t)device_get_match_data(dev);
+
if (fwnode_property_present(fwnode, "adi,alarm-pol")) {
ret = fwnode_property_read_u32(fwnode, "adi,alarm-pol", &data);
if (ret)
@@ -402,8 +417,19 @@ static int max31827_init_client(struct max31827_state *st,
/*
* Set default value.
*/
- res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK,
- MAX31827_ALRM_POL_LOW);
+ switch (type) {
+ case max31827:
+ case max31828:
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK,
+ MAX31827_ALRM_POL_LOW);
+ break;
+ case max31829:
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_ALRM_POL_MASK,
+ MAX31827_ALRM_POL_HIGH);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
}
if (fwnode_property_present(fwnode, "adi,fault-q")) {
@@ -427,8 +453,19 @@ static int max31827_init_client(struct max31827_state *st,
/*
* Set default value.
*/
- res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK,
- MAX31827_FLT_Q_1);
+ switch (type) {
+ case max31827:
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK,
+ MAX31827_FLT_Q_1);
+ break;
+ case max31828:
+ case max31829:
+ res |= FIELD_PREP(MAX31827_CONFIGURATION_FLT_Q_MASK,
+ MAX31827_FLT_Q_4);
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
}
return regmap_write(st->regmap, MAX31827_CONFIGURATION_REG, res);
@@ -486,14 +523,19 @@ static int max31827_probe(struct i2c_client *client)
return PTR_ERR_OR_ZERO(hwmon_dev);
}
-static const struct i2c_device_id max31827_i2c_ids[] = {
- { "max31827", 0 },
- { }
-};
-MODULE_DEVICE_TABLE(i2c, max31827_i2c_ids);
-
static const struct of_device_id max31827_of_match[] = {
- { .compatible = "adi,max31827" },
+ {
+ .compatible = "adi,max31827",
+ .data = (void *)max31827
+ },
+ {
+ .compatible = "adi,max31828",
+ .data = (void *)max31828
+ },
+ {
+ .compatible = "adi,max31829",
+ .data = (void *)max31829
+ },
{ }
};
MODULE_DEVICE_TABLE(of, max31827_of_match);
--
2.34.1
next prev parent reply other threads:[~2023-10-31 22:40 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-10-31 18:21 [PATCH v6 1/5] hwmon: max31827: Handle new properties from the devicetree Daniel Matyas
2023-10-31 18:21 ` Daniel Matyas [this message]
2023-10-31 18:21 ` [PATCH v6 3/5] hwmon: max31827: Update bits with shutdown_write() Daniel Matyas
2023-10-31 18:21 ` [PATCH v6 4/5] hwmon: max31827: Return closest value in update_interval Daniel Matyas
2023-10-31 18:21 ` [PATCH v6 5/5] hwmon: max31827: Add custom attribute for resolution Daniel Matyas
2023-12-11 14:15 ` Guenter Roeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231031182158.124608-2-daniel.matyas@analog.com \
--to=daniel.matyas@analog.com \
--cc=corbet@lwn.net \
--cc=jdelvare@suse.com \
--cc=linux-doc@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@roeck-us.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox