* [PATCH 1/1] Blackfin I2C Driver: since only a few Blackfins lack TWI, just list them in the depends string
@ 2008-05-12 4:18 Bryan Wu
[not found] ` <1210565911-4633-1-git-send-email-cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
0 siblings, 1 reply; 3+ messages in thread
From: Bryan Wu @ 2008-05-12 4:18 UTC (permalink / raw)
To: khali-PUYAD+kWke1g9hUCZPvPmw; +Cc: i2c-GZX6beZjE8VD60Wz+7aTrA, Mike Frysinger
From: Mike Frysinger <vapier.adi-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier.adi-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Signed-off-by: Bryan Wu <cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
drivers/i2c/busses/Kconfig | 5 ++---
1 files changed, 2 insertions(+), 3 deletions(-)
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 48438cc..b93186b 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -101,10 +101,9 @@ config I2C_AU1550
config I2C_BLACKFIN_TWI
tristate "Blackfin TWI I2C support"
depends on BLACKFIN
+ depends on !BF561 && !BF531 && !BF532 && !BF533
help
- This is the TWI I2C device driver for Blackfin BF522, BF525,
- BF527, BF534, BF536, BF537 and BF54x. For other Blackfin processors,
- please don't use this driver.
+ This is the I2C device driver for Blackfin on-chip TWI interface.
This driver can also be built as a module. If so, the module
will be called i2c-bfin-twi.
--
1.5.5
_______________________________________________
i2c mailing list
i2c-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org
http://lists.lm-sensors.org/mailman/listinfo/i2c
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH 1/1] Blackfin I2C Driver: since only a few Blackfins lack TWI, just list them in the depends string
[not found] ` <1210565911-4633-1-git-send-email-cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
@ 2008-05-12 11:27 ` Jean Delvare
[not found] ` <20080512132734.10caa2af-ig7AzVSIIG7kN2dkZ6Wm7A@public.gmane.org>
0 siblings, 1 reply; 3+ messages in thread
From: Jean Delvare @ 2008-05-12 11:27 UTC (permalink / raw)
To: Bryan Wu; +Cc: i2c-GZX6beZjE8VD60Wz+7aTrA, Mike Frysinger
On Mon, 12 May 2008 12:18:31 +0800, Bryan Wu wrote:
> From: Mike Frysinger <vapier.adi-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>
> Signed-off-by: Mike Frysinger <vapier.adi-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> Signed-off-by: Bryan Wu <cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> ---
> drivers/i2c/busses/Kconfig | 5 ++---
> 1 files changed, 2 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index 48438cc..b93186b 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -101,10 +101,9 @@ config I2C_AU1550
> config I2C_BLACKFIN_TWI
> tristate "Blackfin TWI I2C support"
> depends on BLACKFIN
> + depends on !BF561 && !BF531 && !BF532 && !BF533
> help
> - This is the TWI I2C device driver for Blackfin BF522, BF525,
> - BF527, BF534, BF536, BF537 and BF54x. For other Blackfin processors,
> - please don't use this driver.
> + This is the I2C device driver for Blackfin on-chip TWI interface.
>
> This driver can also be built as a module. If so, the module
> will be called i2c-bfin-twi.
Applied, thanks. I've additionally changed "I2C device driver" to "I2C
bus driver" for clarity.
--
Jean Delvare
_______________________________________________
i2c mailing list
i2c-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org
http://lists.lm-sensors.org/mailman/listinfo/i2c
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH 1/1] Blackfin I2C Driver: since only a few Blackfins lack TWI, just list them in the depends string
[not found] ` <20080512132734.10caa2af-ig7AzVSIIG7kN2dkZ6Wm7A@public.gmane.org>
@ 2008-05-12 12:02 ` Bryan Wu
0 siblings, 0 replies; 3+ messages in thread
From: Bryan Wu @ 2008-05-12 12:02 UTC (permalink / raw)
To: Jean Delvare; +Cc: i2c-GZX6beZjE8VD60Wz+7aTrA, Mike Frysinger
On Mon, May 12, 2008 at 7:27 PM, Jean Delvare <khali-PUYAD+kWke1g9hUCZPvPmw@public.gmane.org> wrote:
>
> On Mon, 12 May 2008 12:18:31 +0800, Bryan Wu wrote:
> > From: Mike Frysinger <vapier.adi-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> >
> > Signed-off-by: Mike Frysinger <vapier.adi-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> > Signed-off-by: Bryan Wu <cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> > ---
> > drivers/i2c/busses/Kconfig | 5 ++---
> > 1 files changed, 2 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> > index 48438cc..b93186b 100644
> > --- a/drivers/i2c/busses/Kconfig
> > +++ b/drivers/i2c/busses/Kconfig
> > @@ -101,10 +101,9 @@ config I2C_AU1550
> > config I2C_BLACKFIN_TWI
> > tristate "Blackfin TWI I2C support"
> > depends on BLACKFIN
> > + depends on !BF561 && !BF531 && !BF532 && !BF533
> > help
> > - This is the TWI I2C device driver for Blackfin BF522, BF525,
> > - BF527, BF534, BF536, BF537 and BF54x. For other Blackfin processors,
> > - please don't use this driver.
> > + This is the I2C device driver for Blackfin on-chip TWI interface.
> >
> > This driver can also be built as a module. If so, the module
> > will be called i2c-bfin-twi.
>
> Applied, thanks. I've additionally changed "I2C device driver" to "I2C
> bus driver" for clarity.
>
No problem. Thanks
-Bryan
_______________________________________________
i2c mailing list
i2c-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org
http://lists.lm-sensors.org/mailman/listinfo/i2c
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2008-05-12 12:02 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-05-12 4:18 [PATCH 1/1] Blackfin I2C Driver: since only a few Blackfins lack TWI, just list them in the depends string Bryan Wu
[not found] ` <1210565911-4633-1-git-send-email-cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
2008-05-12 11:27 ` Jean Delvare
[not found] ` <20080512132734.10caa2af-ig7AzVSIIG7kN2dkZ6Wm7A@public.gmane.org>
2008-05-12 12:02 ` Bryan Wu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox