From: Thomas Gessler <Thomas.Gessler-Tvfv6JZYqycq7YrIr1+ioITjL5QYi2yUhC4ANOJQIlc@public.gmane.org>
To: wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org
Cc: michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org,
appana.durga.rao-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org,
khali-PUYAD+kWke1g9hUCZPvPmw@public.gmane.org,
sachin.kamat-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
paul.gortmaker-CWA4WttNNZF54TAoqtyWWQ@public.gmane.org,
Thomas.Gessler-Tvfv6JZYqycq7YrIr1+ioITjL5QYi2yUhC4ANOJQIlc@public.gmane.org,
linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: [PATCH] i2c: i2c-xiic: Fix big-endian register access
Date: Mon, 13 Oct 2014 18:08:47 +0200 [thread overview]
Message-ID: <1413216527-11933-1-git-send-email-Thomas.Gessler@exp2.physik.uni-giessen.de> (raw)
The driver tried to access device registers with the (little-endian)
iowrite/ioread functions. While this worked on little-endian machines
(e.g. Microblaze with AXI bus), it made the driver unusable on
big-endian machines (e.g. PPC405 with PLB).
During the probe function, the driver tried to write a 32-bit reset mask
into the reset register. This caused an error interrupt on big-endian
systems, because the device detected an invalid (byte-swapped) reset
mask. The result was an Oops.
The patch implements an endianness detection similar to the one used in
other Xilinx drivers like drivers/spi/spi-xilinx.c. It was tested on a
PPC405/PLB system.
Signed-off-by: Thomas Gessler <Thomas.Gessler-Tvfv6JZYqycq7YrIr1+ioITjL5QYi2yUhC4ANOJQIlc@public.gmane.org>
---
drivers/i2c/busses/i2c-xiic.c | 58 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 53 insertions(+), 5 deletions(-)
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index ade9223..9842660 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -50,6 +50,11 @@ enum xilinx_i2c_state {
STATE_START
};
+enum xiic_endian {
+ LITTLE,
+ BIG
+};
+
/**
* struct xiic_i2c - Internal representation of the XIIC I2C bus
* @base: Memory base of the HW registers
@@ -74,6 +79,7 @@ struct xiic_i2c {
enum xilinx_i2c_state state;
struct i2c_msg *rx_msg;
int rx_pos;
+ enum xiic_endian endianness;
};
@@ -174,29 +180,58 @@ struct xiic_i2c {
static void xiic_start_xfer(struct xiic_i2c *i2c);
static void __xiic_start_xfer(struct xiic_i2c *i2c);
+/*
+ * For the register read and write functions, a little-endian and big-endian
+ * version are necessary. Endianness is detected during the probe function.
+ * Only the least significant byte [doublet] of the register are ever
+ * accessed. This requires an offset of 3 [2] from the base address for
+ * big-endian systems.
+ */
+
static inline void xiic_setreg8(struct xiic_i2c *i2c, int reg, u8 value)
{
- iowrite8(value, i2c->base + reg);
+ if (i2c->endianness == LITTLE)
+ iowrite8(value, i2c->base + reg);
+ else
+ iowrite8(value, i2c->base + reg + 3);
}
static inline u8 xiic_getreg8(struct xiic_i2c *i2c, int reg)
{
- return ioread8(i2c->base + reg);
+ u8 ret;
+
+ if (i2c->endianness == LITTLE)
+ ret = ioread8(i2c->base + reg);
+ else
+ ret = ioread8(i2c->base + reg + 3);
+ return ret;
}
static inline void xiic_setreg16(struct xiic_i2c *i2c, int reg, u16 value)
{
- iowrite16(value, i2c->base + reg);
+ if (i2c->endianness == LITTLE)
+ iowrite16(value, i2c->base + reg);
+ else
+ iowrite16be(value, i2c->base + reg + 2);
}
static inline void xiic_setreg32(struct xiic_i2c *i2c, int reg, int value)
{
- iowrite32(value, i2c->base + reg);
+ if (i2c->endianness == LITTLE)
+ iowrite32(value, i2c->base + reg);
+ else
+ iowrite32be(value, i2c->base + reg);
}
static inline int xiic_getreg32(struct xiic_i2c *i2c, int reg)
{
- return ioread32(i2c->base + reg);
+ u32 ret;
+
+ if (i2c->endianness == LITTLE)
+ ret = ioread32(i2c->base + reg);
+ else
+ ret = ioread32be(i2c->base + reg);
+ return ret;
}
static inline void xiic_irq_dis(struct xiic_i2c *i2c, u32 mask)
@@ -696,6 +731,7 @@ static int xiic_i2c_probe(struct platform_device *pdev)
struct resource *res;
int ret, irq;
u8 i;
+ u32 sr;
i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
if (!i2c)
@@ -728,6 +764,18 @@ static int xiic_i2c_probe(struct platform_device *pdev)
return ret;
}
+ /*
+ * Detect endianness
+ * Try to reset the TX FIFO. Then check the EMPTY flag. If it is not
+ * set, assume that the endianness was wrong and swap.
+ */
+ i2c->endianness = LITTLE;
+ xiic_setreg32(i2c, XIIC_CR_REG_OFFSET, XIIC_CR_TX_FIFO_RESET_MASK);
+ /* Reset is cleared in xiic_reinit */
+ sr = xiic_getreg32(i2c, XIIC_SR_REG_OFFSET);
+ if (!(sr & XIIC_SR_TX_FIFO_EMPTY_MASK))
+ i2c->endianness = BIG;
+
xiic_reinit(i2c);
/* add i2c adapter to i2c tree */
--
2.1.2
next reply other threads:[~2014-10-13 16:08 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-13 16:08 Thomas Gessler [this message]
[not found] ` <1413216527-11933-1-git-send-email-Thomas.Gessler-Tvfv6JZYqycq7YrIr1+ioITjL5QYi2yUhC4ANOJQIlc@public.gmane.org>
2014-11-13 0:18 ` [PATCH] i2c: i2c-xiic: Fix big-endian register access Wolfram Sang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1413216527-11933-1-git-send-email-Thomas.Gessler@exp2.physik.uni-giessen.de \
--to=thomas.gessler-tvfv6jzyqycq7yrir1+ioitjl5qyi2yuhc4anojqilc@public.gmane.org \
--cc=appana.durga.rao-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org \
--cc=khali-PUYAD+kWke1g9hUCZPvPmw@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org \
--cc=paul.gortmaker-CWA4WttNNZF54TAoqtyWWQ@public.gmane.org \
--cc=sachin.kamat-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).