[RFC PATCH 1/9] iio: imu: inv_mpu6050: Fix multiline comments style

[Daniel Baluta <daniel.baluta@intel.com>]

The preffered style for long (multi-line) comments is:

/*
 * this is a multiline
 * comment
 */

This also fixes checkpatch.pl warning:
WARNING: Block comments use * on subsequent lines

Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
---
 drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 37 +++++++++++++++++++-----------
 1 file changed, 23 insertions(+), 14 deletions(-)

diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
index 2258600..84e014c 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -79,10 +79,11 @@ int inv_mpu6050_switch_engine(struct inv_mpu6050_state *st, bool en, u32 mask)
 {
 	unsigned int d, mgmt_1;
 	int result;
-
-	/* switch clock needs to be careful. Only when gyro is on, can
-	   clock source be switched to gyro. Otherwise, it must be set to
-	   internal clock */
+	/*
+	 * switch clock needs to be careful. Only when gyro is on, can
+	 * clock source be switched to gyro. Otherwise, it must be set to
+	 * internal clock
+	 */
 	if (INV_MPU6050_BIT_PWR_GYRO_STBY == mask) {
 		result = regmap_read(st->map, st->reg->pwr_mgmt_1, &mgmt_1);
 		if (result)
@@ -92,8 +93,10 @@ int inv_mpu6050_switch_engine(struct inv_mpu6050_state *st, bool en, u32 mask)
 	}
 
 	if ((INV_MPU6050_BIT_PWR_GYRO_STBY == mask) && (!en)) {
-		/* turning off gyro requires switch to internal clock first.
-		   Then turn off gyro engine */
+		/*
+		 * turning off gyro requires switch to internal clock first.
+		 * Then turn off gyro engine
+		 */
 		mgmt_1 |= INV_CLK_INTERNAL;
 		result = regmap_write(st->map, st->reg->pwr_mgmt_1, mgmt_1);
 		if (result)
@@ -391,8 +394,10 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,
 	int result;
 
 	mutex_lock(&indio_dev->mlock);
-	/* we should only update scale when the chip is disabled, i.e.,
-		not running */
+	/*
+	 * we should only update scale when the chip is disabled, i.e.
+	 * not running
+	 */
 	if (st->chip_config.enable) {
 		result = -EBUSY;
 		goto error_write_raw;
@@ -529,8 +534,10 @@ static ssize_t inv_attr_show(struct device *dev,
 	s8 *m;
 
 	switch (this_attr->address) {
-	/* In MPU6050, the two matrix are the same because gyro and accel
-	   are integrated in one chip */
+	/*
+	 * In MPU6050, the two matrix are the same because gyro and accel
+	 * are integrated in one chip
+	 */
 	case ATTR_GYRO_MATRIX:
 	case ATTR_ACCL_MATRIX:
 		m = st->plat_data.orientation;
@@ -654,10 +661,12 @@ static int inv_check_and_setup_chip(struct inv_mpu6050_state *st)
 	if (result)
 		return result;
 	msleep(INV_MPU6050_POWER_UP_TIME);
-	/* toggle power state. After reset, the sleep bit could be on
-		or off depending on the OTP settings. Toggling power would
-		make it in a definite state as well as making the hardware
-		state align with the software state */
+	/*
+	 * toggle power state. After reset, the sleep bit could be on
+	 * or off depending on the OTP settings. Toggling power would
+	 * make it in a definite state as well as making the hardware
+	 * state align with the software state
+	 */
 	result = inv_mpu6050_set_power_itg(st, false);
 	if (result)
 		return result;
-- 
2.5.0