* Re: [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down
2019-09-11 9:58 [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down Codrin Ciubotariu
@ 2019-09-14 19:05 ` Ludovic Desroches
2019-09-16 5:20 ` Claudiu.Beznea
2019-09-19 15:06 ` kbouhara
2 siblings, 0 replies; 5+ messages in thread
From: Ludovic Desroches @ 2019-09-14 19:05 UTC (permalink / raw)
To: Codrin Ciubotariu
Cc: linux-i2c, linux-arm-kernel, linux-kernel, nicolas.ferre,
alexandre.belloni, wsa
On Wed, Sep 11, 2019 at 12:58:54PM +0300, Codrin Ciubotariu wrote:
> After a transfer timeout, some faulty I2C slave devices might hold down
> the SCL or the SDA pins. We can generate a bus clear command, hoping that
> the slave might release the pins.
>
> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
I'll be off for three weeks so if there are minor changes, you can keep my
ack.
Thanks
Ludovic
> ---
> drivers/i2c/busses/i2c-at91-master.c | 20 ++++++++++++++++++++
> drivers/i2c/busses/i2c-at91.h | 6 +++++-
> 2 files changed, 25 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/i2c/busses/i2c-at91-master.c b/drivers/i2c/busses/i2c-at91-master.c
> index a3fcc35ffd3b..5f544a16db96 100644
> --- a/drivers/i2c/busses/i2c-at91-master.c
> +++ b/drivers/i2c/busses/i2c-at91-master.c
> @@ -599,6 +599,26 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
> at91_twi_write(dev, AT91_TWI_CR,
> AT91_TWI_THRCLR | AT91_TWI_LOCKCLR);
> }
> +
> + /*
> + * After timeout, some faulty I2C slave devices might hold SCL/SDA down;
> + * we can send a bus clear command, hoping that the pins will be
> + * released
> + */
> + if (!(dev->transfer_status & AT91_TWI_SDA) ||
> + !(dev->transfer_status & AT91_TWI_SCL)) {
> + dev_dbg(dev->dev,
> + "SDA/SCL are down; sending bus clear command\n");
> + if (dev->use_alt_cmd) {
> + unsigned int acr;
> +
> + acr = at91_twi_read(dev, AT91_TWI_ACR);
> + acr &= ~AT91_TWI_ACR_DATAL_MASK;
> + at91_twi_write(dev, AT91_TWI_ACR, acr);
> + }
> + at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_CLEAR);
> + }
> +
> return ret;
> }
>
> diff --git a/drivers/i2c/busses/i2c-at91.h b/drivers/i2c/busses/i2c-at91.h
> index 499b506f6128..ffb870f3ffc6 100644
> --- a/drivers/i2c/busses/i2c-at91.h
> +++ b/drivers/i2c/busses/i2c-at91.h
> @@ -36,6 +36,7 @@
> #define AT91_TWI_SVDIS BIT(5) /* Slave Transfer Disable */
> #define AT91_TWI_QUICK BIT(6) /* SMBus quick command */
> #define AT91_TWI_SWRST BIT(7) /* Software Reset */
> +#define AT91_TWI_CLEAR BIT(15) /* Bus clear command */
> #define AT91_TWI_ACMEN BIT(16) /* Alternative Command Mode Enable */
> #define AT91_TWI_ACMDIS BIT(17) /* Alternative Command Mode Disable */
> #define AT91_TWI_THRCLR BIT(24) /* Transmit Holding Register Clear */
> @@ -69,6 +70,8 @@
> #define AT91_TWI_NACK BIT(8) /* Not Acknowledged */
> #define AT91_TWI_EOSACC BIT(11) /* End Of Slave Access */
> #define AT91_TWI_LOCK BIT(23) /* TWI Lock due to Frame Errors */
> +#define AT91_TWI_SCL BIT(24) /* TWI SCL status */
> +#define AT91_TWI_SDA BIT(25) /* TWI SDA status */
>
> #define AT91_TWI_INT_MASK \
> (AT91_TWI_TXCOMP | AT91_TWI_RXRDY | AT91_TWI_TXRDY | AT91_TWI_NACK \
> @@ -81,7 +84,8 @@
> #define AT91_TWI_THR 0x0034 /* Transmit Holding Register */
>
> #define AT91_TWI_ACR 0x0040 /* Alternative Command Register */
> -#define AT91_TWI_ACR_DATAL(len) ((len) & 0xff)
> +#define AT91_TWI_ACR_DATAL_MASK GENMASK(15, 0)
> +#define AT91_TWI_ACR_DATAL(len) ((len) & AT91_TWI_ACR_DATAL_MASK)
> #define AT91_TWI_ACR_DIR BIT(8)
>
> #define AT91_TWI_FMR 0x0050 /* FIFO Mode Register */
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down
2019-09-11 9:58 [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down Codrin Ciubotariu
2019-09-14 19:05 ` Ludovic Desroches
@ 2019-09-16 5:20 ` Claudiu.Beznea
2019-09-19 15:06 ` kbouhara
2 siblings, 0 replies; 5+ messages in thread
From: Claudiu.Beznea @ 2019-09-16 5:20 UTC (permalink / raw)
To: Codrin.Ciubotariu, linux-i2c, linux-arm-kernel, linux-kernel
Cc: Ludovic.Desroches, alexandre.belloni, wsa
On 11.09.2019 12:58, Codrin Ciubotariu wrote:
> External E-Mail
>
>
> After a transfer timeout, some faulty I2C slave devices might hold down
> the SCL or the SDA pins. We can generate a bus clear command, hoping that
> the slave might release the pins.
>
> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
> ---
> drivers/i2c/busses/i2c-at91-master.c | 20 ++++++++++++++++++++
> drivers/i2c/busses/i2c-at91.h | 6 +++++-
> 2 files changed, 25 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/i2c/busses/i2c-at91-master.c b/drivers/i2c/busses/i2c-at91-master.c
> index a3fcc35ffd3b..5f544a16db96 100644
> --- a/drivers/i2c/busses/i2c-at91-master.c
> +++ b/drivers/i2c/busses/i2c-at91-master.c
> @@ -599,6 +599,26 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
> at91_twi_write(dev, AT91_TWI_CR,
> AT91_TWI_THRCLR | AT91_TWI_LOCKCLR);
> }
> +
> + /*
> + * After timeout, some faulty I2C slave devices might hold SCL/SDA down;
> + * we can send a bus clear command, hoping that the pins will be
> + * released
> + */
> + if (!(dev->transfer_status & AT91_TWI_SDA) ||
> + !(dev->transfer_status & AT91_TWI_SCL)) {
> + dev_dbg(dev->dev,
> + "SDA/SCL are down; sending bus clear command\n");
> + if (dev->use_alt_cmd) {
> + unsigned int acr;
> +
> + acr = at91_twi_read(dev, AT91_TWI_ACR);
> + acr &= ~AT91_TWI_ACR_DATAL_MASK;
> + at91_twi_write(dev, AT91_TWI_ACR, acr);
> + }
> + at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_CLEAR);
> + }
> +
> return ret;
> }
>
> diff --git a/drivers/i2c/busses/i2c-at91.h b/drivers/i2c/busses/i2c-at91.h
> index 499b506f6128..ffb870f3ffc6 100644
> --- a/drivers/i2c/busses/i2c-at91.h
> +++ b/drivers/i2c/busses/i2c-at91.h
> @@ -36,6 +36,7 @@
> #define AT91_TWI_SVDIS BIT(5) /* Slave Transfer Disable */
> #define AT91_TWI_QUICK BIT(6) /* SMBus quick command */
> #define AT91_TWI_SWRST BIT(7) /* Software Reset */
> +#define AT91_TWI_CLEAR BIT(15) /* Bus clear command */
> #define AT91_TWI_ACMEN BIT(16) /* Alternative Command Mode Enable */
> #define AT91_TWI_ACMDIS BIT(17) /* Alternative Command Mode Disable */
> #define AT91_TWI_THRCLR BIT(24) /* Transmit Holding Register Clear */
> @@ -69,6 +70,8 @@
> #define AT91_TWI_NACK BIT(8) /* Not Acknowledged */
> #define AT91_TWI_EOSACC BIT(11) /* End Of Slave Access */
> #define AT91_TWI_LOCK BIT(23) /* TWI Lock due to Frame Errors */
> +#define AT91_TWI_SCL BIT(24) /* TWI SCL status */
> +#define AT91_TWI_SDA BIT(25) /* TWI SDA status */
>
> #define AT91_TWI_INT_MASK \
> (AT91_TWI_TXCOMP | AT91_TWI_RXRDY | AT91_TWI_TXRDY | AT91_TWI_NACK \
> @@ -81,7 +84,8 @@
> #define AT91_TWI_THR 0x0034 /* Transmit Holding Register */
>
> #define AT91_TWI_ACR 0x0040 /* Alternative Command Register */
> -#define AT91_TWI_ACR_DATAL(len) ((len) & 0xff)
> +#define AT91_TWI_ACR_DATAL_MASK GENMASK(15, 0)
> +#define AT91_TWI_ACR_DATAL(len) ((len) & AT91_TWI_ACR_DATAL_MASK)
> #define AT91_TWI_ACR_DIR BIT(8)
>
> #define AT91_TWI_FMR 0x0050 /* FIFO Mode Register */
>
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down
2019-09-11 9:58 [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down Codrin Ciubotariu
2019-09-14 19:05 ` Ludovic Desroches
2019-09-16 5:20 ` Claudiu.Beznea
@ 2019-09-19 15:06 ` kbouhara
2019-09-19 16:25 ` Codrin.Ciubotariu
2 siblings, 1 reply; 5+ messages in thread
From: kbouhara @ 2019-09-19 15:06 UTC (permalink / raw)
To: Codrin Ciubotariu, linux-i2c, linux-arm-kernel, linux-kernel
Cc: ludovic.desroches, nicolas.ferre, alexandre.belloni, wsa
On 9/11/19 11:58 AM, Codrin Ciubotariu wrote:
> After a transfer timeout, some faulty I2C slave devices might hold down
> the SCL or the SDA pins. We can generate a bus clear command, hoping that
> the slave might release the pins.
>
> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
> ---
> drivers/i2c/busses/i2c-at91-master.c | 20 ++++++++++++++++++++
> drivers/i2c/busses/i2c-at91.h | 6 +++++-
> 2 files changed, 25 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/i2c/busses/i2c-at91-master.c b/drivers/i2c/busses/i2c-at91-master.c
> index a3fcc35ffd3b..5f544a16db96 100644
> --- a/drivers/i2c/busses/i2c-at91-master.c
> +++ b/drivers/i2c/busses/i2c-at91-master.c
> @@ -599,6 +599,26 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
> at91_twi_write(dev, AT91_TWI_CR,
> AT91_TWI_THRCLR | AT91_TWI_LOCKCLR);
> }
> +
> + /*
> + * After timeout, some faulty I2C slave devices might hold SCL/SDA down;
> + * we can send a bus clear command, hoping that the pins will be
> + * released
> + */
> + if (!(dev->transfer_status & AT91_TWI_SDA) ||
> + !(dev->transfer_status & AT91_TWI_SCL)) {
> + dev_dbg(dev->dev,
> + "SDA/SCL are down; sending bus clear command\n");
> + if (dev->use_alt_cmd) {
> + unsigned int acr;
> +
> + acr = at91_twi_read(dev, AT91_TWI_ACR);
> + acr &= ~AT91_TWI_ACR_DATAL_MASK;
> + at91_twi_write(dev, AT91_TWI_ACR, acr);
> + }
> + at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_CLEAR);
This bit is not documented on SoCs before SAMA5D2/D4, this write
shouldn't be done unconditionally.
--
Kamel Bouhara, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH] i2c: at91: Send bus clear command if SCL or SDA is down
2019-09-19 15:06 ` kbouhara
@ 2019-09-19 16:25 ` Codrin.Ciubotariu
0 siblings, 0 replies; 5+ messages in thread
From: Codrin.Ciubotariu @ 2019-09-19 16:25 UTC (permalink / raw)
To: kamel.bouhara, linux-i2c, linux-arm-kernel, linux-kernel
Cc: Ludovic.Desroches, Nicolas.Ferre, alexandre.belloni, wsa
On 19.09.2019 18:06, kbouhara wrote:
>
> On 9/11/19 11:58 AM, Codrin Ciubotariu wrote:
>> After a transfer timeout, some faulty I2C slave devices might hold down
>> the SCL or the SDA pins. We can generate a bus clear command, hoping that
>> the slave might release the pins.
>>
>> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
>> ---
>> drivers/i2c/busses/i2c-at91-master.c | 20 ++++++++++++++++++++
>> drivers/i2c/busses/i2c-at91.h | 6 +++++-
>> 2 files changed, 25 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/i2c/busses/i2c-at91-master.c
>> b/drivers/i2c/busses/i2c-at91-master.c
>> index a3fcc35ffd3b..5f544a16db96 100644
>> --- a/drivers/i2c/busses/i2c-at91-master.c
>> +++ b/drivers/i2c/busses/i2c-at91-master.c
>> @@ -599,6 +599,26 @@ static int at91_do_twi_transfer(struct
>> at91_twi_dev *dev)
>> at91_twi_write(dev, AT91_TWI_CR,
>> AT91_TWI_THRCLR | AT91_TWI_LOCKCLR);
>> }
>> +
>> + /*
>> + * After timeout, some faulty I2C slave devices might hold
>> SCL/SDA down;
>> + * we can send a bus clear command, hoping that the pins will be
>> + * released
>> + */
>> + if (!(dev->transfer_status & AT91_TWI_SDA) ||
>> + !(dev->transfer_status & AT91_TWI_SCL)) {
>> + dev_dbg(dev->dev,
>> + "SDA/SCL are down; sending bus clear command\n");
>> + if (dev->use_alt_cmd) {
>> + unsigned int acr;
>> +
>> + acr = at91_twi_read(dev, AT91_TWI_ACR);
>> + acr &= ~AT91_TWI_ACR_DATAL_MASK;
>> + at91_twi_write(dev, AT91_TWI_ACR, acr);
>> + }
>> + at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_CLEAR);
>
> This bit is not documented on SoCs before SAMA5D2/D4, this write
> shouldn't be done unconditionally.
>
>
Indeed, they are not present on SAMA5D4 or earlier SoCs. It is supported
on SAMA5D2 though. I will make a new version and implement the CLEAR
command only for the SoCs that support it.
Thank you for your review.
Best regards,
Codrin
^ permalink raw reply [flat|nested] 5+ messages in thread