From: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
To: Manjunatha GK <manjugk-l0cyMroinI0@public.gmane.org>
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org, "Kalliguddi,
Hema" <hemahk-l0cyMroinI0@public.gmane.org>,
Nishanth Menon <nm-l0cyMroinI0@public.gmane.org>,
Aaro Koskinen
<Aaro.Koskinen-xNZwKgViW5gAvxtiuMwx3w@public.gmane.org>
Subject: Re: [PATCH v4] OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt
Date: Tue, 20 Apr 2010 01:16:33 +0100 [thread overview]
Message-ID: <20100420001633.GM32401@fluff.org.uk> (raw)
In-Reply-To: <1271661262-10538-1-git-send-email-manjugk-l0cyMroinI0@public.gmane.org>
On Mon, Apr 19, 2010 at 12:44:22PM +0530, Manjunatha GK wrote:
> Under certain rare conditions, I2C_STAT[13].RDR bit may be set
> and the corresponding interrupt fire, even there is no data in
> the receive FIFO, or the I2C data transfer is still ongoing.
> These spurious RDR events must be ignored by the software.
>
> This patch handles and ignores RDR spurious interrupts.
>
> The below sequence is required in interrupt handler for
> handling this errata:
> 1. If RDR is set to 1, clear RDR
> 2. Read I2C status register and check for BusBusy bit. If BusBusy
> bit is set, skip remaining steps.
> 3. If BusBusy bit is not set, perform read operation on I2C status
> register.
> 4. If RDR is set, clear the same. Check RDR again and clear if it sets
> RDR bit again.
> 5. Perform I2C Data Read operation N number of times(where N is value
> read from the register BUFSTAT-RXSTAT bit fields).
>
> Note : This errata is applicable for OMAP2 and OMAP3 platforms only.
> It is not applicable for OMAP4.
If people can give me a yes/no before the end of play tomorrow (ie,
2300GMT) then I will get this applied to for-linus/i2c and send it
for -rc.
> Signed-off-by: Manjunatha GK <manjugk-l0cyMroinI0@public.gmane.org>
> Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org
> Cc: Kalliguddi, Hema <hemahk-l0cyMroinI0@public.gmane.org>
> Cc: Nishanth Menon <nm-l0cyMroinI0@public.gmane.org>
> Cc: Aaro Koskinen <Aaro.Koskinen-xNZwKgViW5gAvxtiuMwx3w@public.gmane.org>
>
> ---
> drivers/i2c/busses/i2c-omap.c | 28 ++++++++++++++++++++++++++++
> 1 files changed, 28 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index f2019d2..8309eac 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -796,6 +796,34 @@ complete:
> }
> if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
> u8 num_bytes = 1;
> +
> + /*
> + * I2C Errata(Errata Nos. OMAP2: 1.67, OMAP3: 1.8)
> + * Not applicable for OMAP4.
> + * Under certain rare conditions, RDR could be set again
> + * when the bus is busy, then ignore the interrupt and
> + * clear the interrupt.
> + */
> + if ((stat & OMAP_I2C_STAT_RDR) && !cpu_is_omap44xx()) {
> + /* Step 1: If RDR is set, clear it */
> + omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RDR);
> +
> + /* Step 2: */
> + if(!(omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG)
> + & OMAP_I2C_STAT_BB)) {
> + /* Step 3: */
> + if(omap_i2c_read_reg(dev,
> + OMAP_I2C_STAT_REG)
> + & OMAP_I2C_STAT_RDR) {
> + omap_i2c_ack_stat(dev,
> + OMAP_I2C_STAT_RDR);
> + dev_err(dev->dev,
> + "RDR when the bus is busy.\n");
> + continue;
> + }
> +
> + }
> + }
> if (dev->fifo_size) {
> if (stat & OMAP_I2C_STAT_RRDY)
> num_bytes = dev->fifo_size;
> --
> 1.6.0.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Ben (ben-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org, http://www.fluff.org/)
'a smiley only costs 4 bytes'
next prev parent reply other threads:[~2010-04-20 0:16 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-04-19 7:14 [PATCH v4] OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt Manjunatha GK
[not found] ` <1271661262-10538-1-git-send-email-manjugk-l0cyMroinI0@public.gmane.org>
2010-04-20 0:16 ` Ben Dooks [this message]
[not found] ` <20100420001633.GM32401-elnMNo+KYs3pIgCt6eIbzw@public.gmane.org>
2010-04-21 21:52 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100420001633.GM32401@fluff.org.uk \
--to=ben-linux-elnmno+kys3ytjvyw6ydsg@public.gmane.org \
--cc=Aaro.Koskinen-xNZwKgViW5gAvxtiuMwx3w@public.gmane.org \
--cc=hemahk-l0cyMroinI0@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=manjugk-l0cyMroinI0@public.gmane.org \
--cc=nm-l0cyMroinI0@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).