[PATCH 00/13] Various updates to the Nomadik I2C controller

[PATCH 00/13] Various updates to the Nomadik I2C controller

[Linus Walleij]

A lot of internal refining of this driver has happened on this
driver inside ST-Ericsson since last kernel cycle. Here are the
accumulated changes. I have NOT squashed any development history
this time, since I was severely beat up about it last time.

The last patch in the series for mach-ux500 shall go into my ux500
tree, it is not required for the driver to function, so the rest
of the patches can be applied to the I2C tree without causing any
problems with the platforms using the driver.

Jonas Aberg (1):
  i2c/i2c-nomadik: add regulator support

Linus Walleij (2):
  i2c/i2c-nomadik: fix speed enumerator
  mach-ux500: set proper I2C platform data from MOP500s

Rabin Vincent (1):
  i2c/i2c-nomadik: use pm_runtime API

Virupax Sadashivpetimath (8):
  i2c/i2c-nomadik: make i2c timeout specific per i2c bus
  i2c/i2c-nomadik: corrrect returned error numbers
  i2c/i2c-nomadik: correct adapter timeout initialization
  i2c/i2c-nomadik: print abort cause only on abort tag
  i2c/i2c-nomadik: add code to retry on timeout failure
  i2c/i2c-nomadik: change the TX and RX threshold
  i2c/i2c-nomadik: remove the unnecessary delay
  i2c/i2c-nomadik: reset the hw after status check

srinidhi kasagar (1):
  i2c/i2c-nomadik: remove the redundant error message

 arch/arm/mach-ux500/board-mop500.c       |   14 +-
 arch/arm/plat-nomadik/include/plat/i2c.h |    8 +-
 drivers/i2c/busses/i2c-nomadik.c         |  272 ++++++++++++++++++++----------
 3 files changed, 194 insertions(+), 100 deletions(-)

-- 
1.7.5.1

Re: [PATCH 00/13] Various updates to the Nomadik I2C controller

[Ben Dooks]

On Mon, May 09, 2011 at 11:34:37PM +0200, Linus Walleij wrote:
> A lot of internal refining of this driver has happened on this
> driver inside ST-Ericsson since last kernel cycle. Here are the
> accumulated changes. I have NOT squashed any development history
> this time, since I was severely beat up about it last time.
> 
> The last patch in the series for mach-ux500 shall go into my ux500
> tree, it is not required for the driver to function, so the rest
> of the patches can be applied to the I2C tree without causing any
> problems with the platforms using the driver.
> 
> Jonas Aberg (1):
>   i2c/i2c-nomadik: add regulator support
> 
> Linus Walleij (2):
>   i2c/i2c-nomadik: fix speed enumerator
>   mach-ux500: set proper I2C platform data from MOP500s
> 
> Rabin Vincent (1):
>   i2c/i2c-nomadik: use pm_runtime API
> 
> Virupax Sadashivpetimath (8):
>   i2c/i2c-nomadik: make i2c timeout specific per i2c bus
>   i2c/i2c-nomadik: corrrect returned error numbers
>   i2c/i2c-nomadik: correct adapter timeout initialization
>   i2c/i2c-nomadik: print abort cause only on abort tag
>   i2c/i2c-nomadik: add code to retry on timeout failure
>   i2c/i2c-nomadik: change the TX and RX threshold
>   i2c/i2c-nomadik: remove the unnecessary delay
>   i2c/i2c-nomadik: reset the hw after status check
> 
> srinidhi kasagar (1):
>   i2c/i2c-nomadik: remove the redundant error message
> 
>  arch/arm/mach-ux500/board-mop500.c       |   14 +-
>  arch/arm/plat-nomadik/include/plat/i2c.h |    8 +-
>  drivers/i2c/busses/i2c-nomadik.c         |  272 ++++++++++++++++++++----------
>  3 files changed, 194 insertions(+), 100 deletions(-)

right, mostly looks fine, just one or two bits
that could do with looking at if possible.