* [PATCH 3/5] i2c: remove ixp2000 driver
[not found] <1333503243-7702-1-git-send-email-robherring2@gmail.com>
@ 2012-04-04 1:34 ` Rob Herring
2012-04-22 16:31 ` Wolfram Sang
0 siblings, 1 reply; 2+ messages in thread
From: Rob Herring @ 2012-04-04 1:34 UTC (permalink / raw)
To: linux-kernel, linux-arm-kernel
Cc: Russell King, Arnd Bergmann, Nicolas Pitre,
Wolfram Sang (embedded platforms), Rob Herring,
Jean Delvare (PC drivers, core), linux-i2c,
Ben Dooks (embedded platforms), Olof Johansson
From: Rob Herring <rob.herring@calxeda.com>
The platform is removed, so there are no users of this driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
---
drivers/i2c/busses/Kconfig | 14 ----
drivers/i2c/busses/Makefile | 1 -
drivers/i2c/busses/i2c-ixp2000.c | 157 --------------------------------------
3 files changed, 0 insertions(+), 172 deletions(-)
delete mode 100644 drivers/i2c/busses/i2c-ixp2000.c
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index d2c5095..188543d 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -445,20 +445,6 @@ config I2C_IOP3XX
This driver can also be built as a module. If so, the module
will be called i2c-iop3xx.
-config I2C_IXP2000
- tristate "IXP2000 GPIO-Based I2C Interface (DEPRECATED)"
- depends on ARCH_IXP2000
- select I2C_ALGOBIT
- help
- Say Y here if you have an Intel IXP2000 (2400, 2800, 2850) based
- system and are using GPIO lines for an I2C bus.
-
- This support is also available as a module. If so, the module
- will be called i2c-ixp2000.
-
- This driver is deprecated and will be dropped soon. Use i2c-gpio
- instead.
-
config I2C_MPC
tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx"
depends on PPC
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 569567b..ce3c2be 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -44,7 +44,6 @@ obj-$(CONFIG_I2C_IBM_IIC) += i2c-ibm_iic.o
obj-$(CONFIG_I2C_IMX) += i2c-imx.o
obj-$(CONFIG_I2C_INTEL_MID) += i2c-intel-mid.o
obj-$(CONFIG_I2C_IOP3XX) += i2c-iop3xx.o
-obj-$(CONFIG_I2C_IXP2000) += i2c-ixp2000.o
obj-$(CONFIG_I2C_MPC) += i2c-mpc.o
obj-$(CONFIG_I2C_MV64XXX) += i2c-mv64xxx.o
obj-$(CONFIG_I2C_MXS) += i2c-mxs.o
diff --git a/drivers/i2c/busses/i2c-ixp2000.c b/drivers/i2c/busses/i2c-ixp2000.c
deleted file mode 100644
index 5d263f90..0000000
--- a/drivers/i2c/busses/i2c-ixp2000.c
+++ /dev/null
@@ -1,157 +0,0 @@
-/*
- * drivers/i2c/busses/i2c-ixp2000.c
- *
- * I2C adapter for IXP2000 systems using GPIOs for I2C bus
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- * Based on IXDP2400 code by: Naeem M. Afzal <naeem.m.afzal@intel.com>
- * Made generic by: Jeff Daly <jeffrey.daly@intel.com>
- *
- * Copyright (c) 2003-2004 MontaVista Software Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
- * From Jeff Daly:
- *
- * I2C adapter driver for Intel IXDP2xxx platforms. This should work for any
- * IXP2000 platform if it uses the HW GPIO in the same manner. Basically,
- * SDA and SCL GPIOs have external pullups. Setting the respective GPIO to
- * an input will make the signal a '1' via the pullup. Setting them to
- * outputs will pull them down.
- *
- * The GPIOs are open drain signals and are used as configuration strap inputs
- * during power-up so there's generally a buffer on the board that needs to be
- * 'enabled' to drive the GPIOs.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/i2c.h>
-#include <linux/i2c-algo-bit.h>
-#include <linux/slab.h>
-
-#include <mach/hardware.h> /* Pick up IXP2000-specific bits */
-#include <mach/gpio-ixp2000.h>
-
-static inline int ixp2000_scl_pin(void *data)
-{
- return ((struct ixp2000_i2c_pins*)data)->scl_pin;
-}
-
-static inline int ixp2000_sda_pin(void *data)
-{
- return ((struct ixp2000_i2c_pins*)data)->sda_pin;
-}
-
-
-static void ixp2000_bit_setscl(void *data, int val)
-{
- int i = 5000;
-
- if (val) {
- gpio_line_config(ixp2000_scl_pin(data), GPIO_IN);
- while(!gpio_line_get(ixp2000_scl_pin(data)) && i--);
- } else {
- gpio_line_config(ixp2000_scl_pin(data), GPIO_OUT);
- }
-}
-
-static void ixp2000_bit_setsda(void *data, int val)
-{
- if (val) {
- gpio_line_config(ixp2000_sda_pin(data), GPIO_IN);
- } else {
- gpio_line_config(ixp2000_sda_pin(data), GPIO_OUT);
- }
-}
-
-static int ixp2000_bit_getscl(void *data)
-{
- return gpio_line_get(ixp2000_scl_pin(data));
-}
-
-static int ixp2000_bit_getsda(void *data)
-{
- return gpio_line_get(ixp2000_sda_pin(data));
-}
-
-struct ixp2000_i2c_data {
- struct ixp2000_i2c_pins *gpio_pins;
- struct i2c_adapter adapter;
- struct i2c_algo_bit_data algo_data;
-};
-
-static int ixp2000_i2c_remove(struct platform_device *plat_dev)
-{
- struct ixp2000_i2c_data *drv_data = platform_get_drvdata(plat_dev);
-
- platform_set_drvdata(plat_dev, NULL);
-
- i2c_del_adapter(&drv_data->adapter);
-
- kfree(drv_data);
-
- return 0;
-}
-
-static int ixp2000_i2c_probe(struct platform_device *plat_dev)
-{
- int err;
- struct ixp2000_i2c_pins *gpio = plat_dev->dev.platform_data;
- struct ixp2000_i2c_data *drv_data =
- kzalloc(sizeof(struct ixp2000_i2c_data), GFP_KERNEL);
-
- if (!drv_data)
- return -ENOMEM;
- drv_data->gpio_pins = gpio;
-
- drv_data->algo_data.data = gpio;
- drv_data->algo_data.setsda = ixp2000_bit_setsda;
- drv_data->algo_data.setscl = ixp2000_bit_setscl;
- drv_data->algo_data.getsda = ixp2000_bit_getsda;
- drv_data->algo_data.getscl = ixp2000_bit_getscl;
- drv_data->algo_data.udelay = 6;
- drv_data->algo_data.timeout = HZ;
-
- strlcpy(drv_data->adapter.name, plat_dev->dev.driver->name,
- sizeof(drv_data->adapter.name));
- drv_data->adapter.algo_data = &drv_data->algo_data,
-
- drv_data->adapter.dev.parent = &plat_dev->dev;
-
- gpio_line_config(gpio->sda_pin, GPIO_IN);
- gpio_line_config(gpio->scl_pin, GPIO_IN);
- gpio_line_set(gpio->scl_pin, 0);
- gpio_line_set(gpio->sda_pin, 0);
-
- if ((err = i2c_bit_add_bus(&drv_data->adapter)) != 0) {
- dev_err(&plat_dev->dev, "Could not install, error %d\n", err);
- kfree(drv_data);
- return err;
- }
-
- platform_set_drvdata(plat_dev, drv_data);
-
- return 0;
-}
-
-static struct platform_driver ixp2000_i2c_driver = {
- .probe = ixp2000_i2c_probe,
- .remove = ixp2000_i2c_remove,
- .driver = {
- .name = "IXP2000-I2C",
- .owner = THIS_MODULE,
- },
-};
-
-module_platform_driver(ixp2000_i2c_driver);
-
-MODULE_AUTHOR ("Deepak Saxena <dsaxena@plexity.net>");
-MODULE_DESCRIPTION("IXP2000 GPIO-based I2C bus driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:IXP2000-I2C");
-
--
1.7.5.4
^ permalink raw reply related [flat|nested] 2+ messages in thread