From: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
To: "to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org"
<to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org>
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Belloni
<alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>,
Fabio Estevam <r49496-KZfg59tc24xl57MIdRCFDg@public.gmane.org>,
Lucas Stach <l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>,
Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>,
Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>
Subject: Re: [PATCH] i2c: mxs: Rework the PIO mode operation
Date: Wed, 17 Jul 2013 19:04:00 +0200 [thread overview]
Message-ID: <201307171904.00784.marex@denx.de> (raw)
In-Reply-To: <1UzQet-1Vf4pE0-VM4m3MaA7PGi2rA4ip7KQzlaCuRwF3y+@public.gmane.org>
Dear to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org,
> Hi,
>
> > > Analyze and rework the PIO mode operation. The PIO mode operation
> > > was unreliable on MX28, by analyzing the bus with LA, the checks for
> > > when data were available or were to be sent were wrong.
> > >
> > > The PIO WRITE has to be completely reworked as it multiple problems.
> > > The MX23 datasheet helped here, see comments in the code for
> > > details.
> > > The problems boil down to:
> > > - RUN bit in CTRL0 must be set after DATA register was written - The
> > > PIO transfer must be 4 bytes long tops, otherwise use
> > > clock stretching.
> > > Both of these fixes are implemented.
> > >
> > > The PIO READ operation can only be done for up to four bytes as we
> > > are unable to read out the data from the DATA register fast enough.
> > >
> > > This patch also tries to document the investigation within the code.
> > >
> > > Signed-off-by: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
> > > Cc: Alexandre Belloni <alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> > > Cc: Fabio Estevam <r49496-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
> > > Cc: Lucas Stach <l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> > > Cc: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> > > Cc: Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>
> > > Cc: <to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org>
> >
> > I so far got confirmation from ALexandre this patch works. Can someone
> > else test it please? I'd like to roll out a final version to close
> > this issue.
>
> sorry, I couldn't test the patch until today on my iMX283 board.
> It works when reading the registers from the temperature sensor TCN75A.
> But it fails when writing less than 7 bytes to the EEPROM (24LC32). Then
> I always get a 'Connection timed out' error in the user space.
Thinking about this, did you correctly configure the EEPROM write sector size? I
think it's 32 bytes for this device.
Best regards,
Marek Vasut
next prev parent reply other threads:[~2013-07-17 17:04 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-08 19:46 [PATCH] i2c: mxs: Rework the PIO mode operation Marek Vasut
[not found] ` <1373312807-13227-1-git-send-email-marex-ynQEQJNshbs@public.gmane.org>
2013-07-08 19:49 ` Marek Vasut
2013-07-09 13:21 ` Alexandre Belloni
2013-07-15 2:05 ` Marek Vasut
[not found] ` <201307150405.53110.marex-ynQEQJNshbs@public.gmane.org>
2013-07-15 12:14 ` Lucas Stach
[not found] ` <1373890479.4172.3.camel-WzVe3FnzCwFR6QfukMTsflXZhhPuCNm+@public.gmane.org>
2013-07-15 12:27 ` Marek Vasut
2013-07-15 14:58 ` Shawn Guo
[not found] ` <20130715145836.GB23589-rvtDTF3kK1ictlrPMvKcciBecyulp+rMXqFh9Ls21Oc@public.gmane.org>
2013-07-15 23:25 ` Marek Vasut
2013-07-17 12:16 ` to-fleischer-zqRNUXuvxA0b1SvskN2V4Q
[not found] ` <1UzQet-1Vf4pE0-VM4m3MaA7PGi2rA4ip7KQzlaCuRwF3y+@public.gmane.org>
2013-07-17 16:23 ` Marek Vasut
2013-07-17 17:04 ` Marek Vasut [this message]
[not found] ` <201307171904.00784.marex-ynQEQJNshbs@public.gmane.org>
2013-07-18 19:12 ` Torsten Fleischer
[not found] ` <3767128.gOKkIqK4p5-BVXpyJtzy6LO1Ldfs0Uenw@public.gmane.org>
2013-07-21 21:21 ` Marek Vasut
[not found] ` <201307212321.22207.marex-ynQEQJNshbs@public.gmane.org>
2013-07-28 9:47 ` Torsten Fleischer
2013-07-15 12:43 ` Lucas Stach
[not found] ` <1373892198.4172.17.camel-WzVe3FnzCwFR6QfukMTsflXZhhPuCNm+@public.gmane.org>
2013-07-15 23:24 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201307171904.00784.marex@denx.de \
--to=marex-ynqeqjnshbs@public.gmane.org \
--cc=alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
--cc=l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=r49496-KZfg59tc24xl57MIdRCFDg@public.gmane.org \
--cc=shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org \
--cc=wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).