From mboxrd@z Thu Jan 1 00:00:00 1970 From: "David E. Box" Subject: Re: [PATCH 2/2] i2c: designware: Allow build Baytrail semaphore support when IOSF_MBI=m Date: Tue, 12 Apr 2016 14:46:55 -0700 Message-ID: <20160412214655.GA27603@pathfinder> References: <1449748124-20744-1-git-send-email-jarkko.nikula@linux.intel.com> <1449748124-20744-2-git-send-email-jarkko.nikula@linux.intel.com> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Return-path: Received: from mga04.intel.com ([192.55.52.120]:57633 "EHLO mga04.intel.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1756492AbcDLVrv (ORCPT ); Tue, 12 Apr 2016 17:47:51 -0400 Content-Disposition: inline In-Reply-To: <1449748124-20744-2-git-send-email-jarkko.nikula@linux.intel.com> Sender: linux-i2c-owner@vger.kernel.org List-Id: linux-i2c@vger.kernel.org To: Jarkko Nikula Cc: linux-i2c@vger.kernel.org, Wolfram Sang , Andy Shevchenko , Mika Westerberg On Thu, Dec 10, 2015 at 01:48:44PM +0200, Jarkko Nikula wrote: > I believe i2c-designware-baytrail.c doesn't have strict dependency that > Intel SoC IOSF Sideband support must be always built-in in order to be > able to compile support for Intel Baytrail I2C bus sharing HW semaphore. > > Redefine build dependencies so that CONFIG_IOSF_MBI=y is required only > when CONFIG_I2C_DESIGNWARE_PLATFORM is built-in. > > Signed-off-by: Jarkko Nikula > --- > Hi David. Can you ack/nak this patch as I'm not fully familiar with this > HW semaphore can there be problems when IOSF_MBI is built as a module. > At least I'm getting similar sensible looking "punit semaphore > acquired/held for x ms" debug messages when I modprobe/rmmod > i2c_designware_platform independently is the CONFIG_IOSF_MBI=y or =m. > --- > drivers/i2c/busses/Kconfig | 4 +++- > 1 file changed, 3 insertions(+), 1 deletion(-) > > diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig > index 69c46fe13777..76f4d024def0 100644 > --- a/drivers/i2c/busses/Kconfig > +++ b/drivers/i2c/busses/Kconfig > @@ -490,7 +490,9 @@ config I2C_DESIGNWARE_PCI > > config I2C_DESIGNWARE_BAYTRAIL > bool "Intel Baytrail I2C semaphore support" > - depends on I2C_DESIGNWARE_PLATFORM && IOSF_MBI=y && ACPI > + depends on ACPI > + depends on (I2C_DESIGNWARE_PLATFORM=m && IOSF_MBI) || \ > + (I2C_DESIGNWARE_PLATFORM=y && IOSF_MBI=y) > help > This driver enables managed host access to the PMIC I2C bus on select > Intel BayTrail platforms using the X-Powers AXP288 PMIC. It allows > -- > 2.6.2 > Acked-by: David Box