* [RFC PATCH] i2c: imx: dma map the i2c data i/o register
@ 2019-01-16 16:17 Laurentiu Tudor
2019-01-16 17:55 ` Robin Murphy
0 siblings, 1 reply; 3+ messages in thread
From: Laurentiu Tudor @ 2019-01-16 16:17 UTC (permalink / raw)
To: linux-i2c, linux-imx, iommu, kernel, wsa
Cc: linux-arm-kernel, linux-kernel, robin.murphy, Laurentiu Tudor
This is an attempt to fix an iommu exception when doing dma to the
i2c controller with EDMA. Without these mappings the smmu raises a
context fault [1] exactly with the address of the i2c data i/o reg.
This was seen on an NXP LS1043A chip while working on enabling SMMU.
[1] arm-smmu 9000000.iommu: Unhandled context fault: fsr=0x402,
iova=0x02180004, fsynr=0x150021, cb=7
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
---
drivers/i2c/busses/i2c-imx.c | 57 +++++++++++++++++++++++++++++-------
1 file changed, 47 insertions(+), 10 deletions(-)
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index 4e34b1572756..07cc8f4b45b9 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -202,6 +202,9 @@ struct imx_i2c_struct {
struct pinctrl_state *pinctrl_pins_gpio;
struct imx_i2c_dma *dma;
+
+ dma_addr_t dma_tx_addr;
+ dma_addr_t dma_rx_addr;
};
static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
@@ -274,17 +277,20 @@ static inline unsigned char imx_i2c_read_reg(struct imx_i2c_struct *i2c_imx,
/* Functions for DMA support */
static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
- dma_addr_t phy_addr)
+ phys_addr_t phy_addr)
{
struct imx_i2c_dma *dma;
struct dma_slave_config dma_sconfig;
struct device *dev = &i2c_imx->adapter.dev;
int ret;
+ phys_addr_t i2dr_pa;
dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL);
if (!dma)
return -ENOMEM;
+ i2dr_pa = phy_addr + (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
+
dma->chan_tx = dma_request_chan(dev, "tx");
if (IS_ERR(dma->chan_tx)) {
ret = PTR_ERR(dma->chan_tx);
@@ -293,15 +299,25 @@ static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
goto fail_al;
}
- dma_sconfig.dst_addr = phy_addr +
- (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
+ i2c_imx->dma_tx_addr = dma_map_resource(dma->chan_tx->device->dev,
+ i2dr_pa,
+ DMA_SLAVE_BUSWIDTH_1_BYTE,
+ DMA_MEM_TO_DEV, 0);
+ ret = dma_mapping_error(dma->chan_tx->device->dev,
+ i2c_imx->dma_tx_addr);
+ if (ret) {
+ dev_err(dev, "can't dma map tx destination (%d)\n", ret);
+ goto fail_tx;
+ }
+
+ dma_sconfig.dst_addr = i2c_imx->dma_tx_addr;
dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
dma_sconfig.dst_maxburst = 1;
dma_sconfig.direction = DMA_MEM_TO_DEV;
ret = dmaengine_slave_config(dma->chan_tx, &dma_sconfig);
if (ret < 0) {
dev_err(dev, "can't configure tx channel (%d)\n", ret);
- goto fail_tx;
+ goto fail_tx_dma;
}
dma->chan_rx = dma_request_chan(dev, "rx");
@@ -309,18 +325,28 @@ static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
ret = PTR_ERR(dma->chan_rx);
if (ret != -ENODEV && ret != -EPROBE_DEFER)
dev_err(dev, "can't request DMA rx channel (%d)\n", ret);
- goto fail_tx;
+ goto fail_tx_dma;
}
- dma_sconfig.src_addr = phy_addr +
- (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
+ i2c_imx->dma_rx_addr = dma_map_resource(dma->chan_rx->device->dev,
+ i2dr_pa,
+ DMA_SLAVE_BUSWIDTH_1_BYTE,
+ DMA_DEV_TO_MEM, 0);
+ ret = dma_mapping_error(dma->chan_rx->device->dev,
+ i2c_imx->dma_rx_addr);
+ if (ret) {
+ dev_err(dev, "can't dma map rx source (%d)\n", ret);
+ goto fail_rx;
+ }
+
+ dma_sconfig.src_addr = i2c_imx->dma_rx_addr;
dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
dma_sconfig.src_maxburst = 1;
dma_sconfig.direction = DMA_DEV_TO_MEM;
ret = dmaengine_slave_config(dma->chan_rx, &dma_sconfig);
if (ret < 0) {
dev_err(dev, "can't configure rx channel (%d)\n", ret);
- goto fail_rx;
+ goto fail_rx_dma;
}
i2c_imx->dma = dma;
@@ -330,8 +356,14 @@ static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
return 0;
+fail_rx_dma:
+ dma_unmap_resource(dma->chan_rx->device->dev, i2c_imx->dma_rx_addr,
+ DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_DEV_TO_MEM, 0);
fail_rx:
dma_release_channel(dma->chan_rx);
+fail_tx_dma:
+ dma_unmap_resource(dma->chan_tx->device->dev, i2c_imx->dma_tx_addr,
+ DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_MEM_TO_DEV, 0);
fail_tx:
dma_release_channel(dma->chan_tx);
fail_al:
@@ -1057,7 +1089,7 @@ static int i2c_imx_probe(struct platform_device *pdev)
struct imxi2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
void __iomem *base;
int irq, ret;
- dma_addr_t phy_addr;
+ phys_addr_t phy_addr;
dev_dbg(&pdev->dev, "<%s>\n", __func__);
@@ -1072,7 +1104,7 @@ static int i2c_imx_probe(struct platform_device *pdev)
if (IS_ERR(base))
return PTR_ERR(base);
- phy_addr = (dma_addr_t)res->start;
+ phy_addr = res->start;
i2c_imx = devm_kzalloc(&pdev->dev, sizeof(*i2c_imx), GFP_KERNEL);
if (!i2c_imx)
return -ENOMEM;
@@ -1220,6 +1252,11 @@ static int i2c_imx_remove(struct platform_device *pdev)
pm_runtime_put_noidle(&pdev->dev);
pm_runtime_disable(&pdev->dev);
+ dma_unmap_resource(&pdev->dev, i2c_imx->dma_tx_addr,
+ DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_MEM_TO_DEV, 0);
+ dma_unmap_resource(&pdev->dev, i2c_imx->dma_rx_addr,
+ DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_DEV_TO_MEM, 0);
+
return 0;
}
--
2.17.1
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [RFC PATCH] i2c: imx: dma map the i2c data i/o register
2019-01-16 16:17 [RFC PATCH] i2c: imx: dma map the i2c data i/o register Laurentiu Tudor
@ 2019-01-16 17:55 ` Robin Murphy
2019-01-17 9:58 ` Laurentiu Tudor
0 siblings, 1 reply; 3+ messages in thread
From: Robin Murphy @ 2019-01-16 17:55 UTC (permalink / raw)
To: Laurentiu Tudor, linux-i2c, linux-imx, iommu, kernel, wsa
Cc: linux-arm-kernel, linux-kernel
On 16/01/2019 16:17, Laurentiu Tudor wrote:
> This is an attempt to fix an iommu exception when doing dma to the
> i2c controller with EDMA. Without these mappings the smmu raises a
> context fault [1] exactly with the address of the i2c data i/o reg.
> This was seen on an NXP LS1043A chip while working on enabling SMMU.
Rather than gradually adding much the same code to potentially every
possible client driver, can it not be implemented once in the edma
driver as was done for pl330 and rcar-dmac? That also sidesteps any of
the nastiness of smuggling a dma_addr_t via a phys_addr_t variable.
Robin.
> [1] arm-smmu 9000000.iommu: Unhandled context fault: fsr=0x402,
> iova=0x02180004, fsynr=0x150021, cb=7
>
> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
> ---
> drivers/i2c/busses/i2c-imx.c | 57 +++++++++++++++++++++++++++++-------
> 1 file changed, 47 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
> index 4e34b1572756..07cc8f4b45b9 100644
> --- a/drivers/i2c/busses/i2c-imx.c
> +++ b/drivers/i2c/busses/i2c-imx.c
> @@ -202,6 +202,9 @@ struct imx_i2c_struct {
> struct pinctrl_state *pinctrl_pins_gpio;
>
> struct imx_i2c_dma *dma;
> +
> + dma_addr_t dma_tx_addr;
> + dma_addr_t dma_rx_addr;
> };
>
> static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
> @@ -274,17 +277,20 @@ static inline unsigned char imx_i2c_read_reg(struct imx_i2c_struct *i2c_imx,
>
> /* Functions for DMA support */
> static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
> - dma_addr_t phy_addr)
> + phys_addr_t phy_addr)
> {
> struct imx_i2c_dma *dma;
> struct dma_slave_config dma_sconfig;
> struct device *dev = &i2c_imx->adapter.dev;
> int ret;
> + phys_addr_t i2dr_pa;
>
> dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL);
> if (!dma)
> return -ENOMEM;
>
> + i2dr_pa = phy_addr + (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
> +
> dma->chan_tx = dma_request_chan(dev, "tx");
> if (IS_ERR(dma->chan_tx)) {
> ret = PTR_ERR(dma->chan_tx);
> @@ -293,15 +299,25 @@ static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
> goto fail_al;
> }
>
> - dma_sconfig.dst_addr = phy_addr +
> - (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
> + i2c_imx->dma_tx_addr = dma_map_resource(dma->chan_tx->device->dev,
> + i2dr_pa,
> + DMA_SLAVE_BUSWIDTH_1_BYTE,
> + DMA_MEM_TO_DEV, 0);
> + ret = dma_mapping_error(dma->chan_tx->device->dev,
> + i2c_imx->dma_tx_addr);
> + if (ret) {
> + dev_err(dev, "can't dma map tx destination (%d)\n", ret);
> + goto fail_tx;
> + }
> +
> + dma_sconfig.dst_addr = i2c_imx->dma_tx_addr;
> dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> dma_sconfig.dst_maxburst = 1;
> dma_sconfig.direction = DMA_MEM_TO_DEV;
> ret = dmaengine_slave_config(dma->chan_tx, &dma_sconfig);
> if (ret < 0) {
> dev_err(dev, "can't configure tx channel (%d)\n", ret);
> - goto fail_tx;
> + goto fail_tx_dma;
> }
>
> dma->chan_rx = dma_request_chan(dev, "rx");
> @@ -309,18 +325,28 @@ static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
> ret = PTR_ERR(dma->chan_rx);
> if (ret != -ENODEV && ret != -EPROBE_DEFER)
> dev_err(dev, "can't request DMA rx channel (%d)\n", ret);
> - goto fail_tx;
> + goto fail_tx_dma;
> }
>
> - dma_sconfig.src_addr = phy_addr +
> - (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
> + i2c_imx->dma_rx_addr = dma_map_resource(dma->chan_rx->device->dev,
> + i2dr_pa,
> + DMA_SLAVE_BUSWIDTH_1_BYTE,
> + DMA_DEV_TO_MEM, 0);
> + ret = dma_mapping_error(dma->chan_rx->device->dev,
> + i2c_imx->dma_rx_addr);
> + if (ret) {
> + dev_err(dev, "can't dma map rx source (%d)\n", ret);
> + goto fail_rx;
> + }
> +
> + dma_sconfig.src_addr = i2c_imx->dma_rx_addr;
> dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> dma_sconfig.src_maxburst = 1;
> dma_sconfig.direction = DMA_DEV_TO_MEM;
> ret = dmaengine_slave_config(dma->chan_rx, &dma_sconfig);
> if (ret < 0) {
> dev_err(dev, "can't configure rx channel (%d)\n", ret);
> - goto fail_rx;
> + goto fail_rx_dma;
> }
>
> i2c_imx->dma = dma;
> @@ -330,8 +356,14 @@ static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
>
> return 0;
>
> +fail_rx_dma:
> + dma_unmap_resource(dma->chan_rx->device->dev, i2c_imx->dma_rx_addr,
> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_DEV_TO_MEM, 0);
> fail_rx:
> dma_release_channel(dma->chan_rx);
> +fail_tx_dma:
> + dma_unmap_resource(dma->chan_tx->device->dev, i2c_imx->dma_tx_addr,
> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_MEM_TO_DEV, 0);
> fail_tx:
> dma_release_channel(dma->chan_tx);
> fail_al:
> @@ -1057,7 +1089,7 @@ static int i2c_imx_probe(struct platform_device *pdev)
> struct imxi2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
> void __iomem *base;
> int irq, ret;
> - dma_addr_t phy_addr;
> + phys_addr_t phy_addr;
>
> dev_dbg(&pdev->dev, "<%s>\n", __func__);
>
> @@ -1072,7 +1104,7 @@ static int i2c_imx_probe(struct platform_device *pdev)
> if (IS_ERR(base))
> return PTR_ERR(base);
>
> - phy_addr = (dma_addr_t)res->start;
> + phy_addr = res->start;
> i2c_imx = devm_kzalloc(&pdev->dev, sizeof(*i2c_imx), GFP_KERNEL);
> if (!i2c_imx)
> return -ENOMEM;
> @@ -1220,6 +1252,11 @@ static int i2c_imx_remove(struct platform_device *pdev)
> pm_runtime_put_noidle(&pdev->dev);
> pm_runtime_disable(&pdev->dev);
>
> + dma_unmap_resource(&pdev->dev, i2c_imx->dma_tx_addr,
> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_MEM_TO_DEV, 0);
> + dma_unmap_resource(&pdev->dev, i2c_imx->dma_rx_addr,
> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_DEV_TO_MEM, 0);
> +
> return 0;
> }
>
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [RFC PATCH] i2c: imx: dma map the i2c data i/o register
2019-01-16 17:55 ` Robin Murphy
@ 2019-01-17 9:58 ` Laurentiu Tudor
0 siblings, 0 replies; 3+ messages in thread
From: Laurentiu Tudor @ 2019-01-17 9:58 UTC (permalink / raw)
To: Robin Murphy, linux-i2c@vger.kernel.org, dl-linux-imx,
iommu@lists.linux-foundation.org, kernel@pengutronix.de,
wsa@the-dreams.de
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Hi Robin,
On 16.01.2019 19:55, Robin Murphy wrote:
> On 16/01/2019 16:17, Laurentiu Tudor wrote:
>> This is an attempt to fix an iommu exception when doing dma to the
>> i2c controller with EDMA. Without these mappings the smmu raises a
>> context fault [1] exactly with the address of the i2c data i/o reg.
>> This was seen on an NXP LS1043A chip while working on enabling SMMU.
>
> Rather than gradually adding much the same code to potentially every
> possible client driver, can it not be implemented once in the edma
> driver as was done for pl330 and rcar-dmac? That also sidesteps any of
> the nastiness of smuggling a dma_addr_t via a phys_addr_t variable.
Thanks for the pointer. I was actually unsure where this should be
tackled: either i2c or dma side. Plus I somehow managed to completely
miss the support added in the dma drivers you mention. I'll start
looking into stealing some of your code [1]. :-)
[1]
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=4d6d74e22096543cb3b35e717cf1b9aea3655f37
---
Best Regards, Laurentiu
>
>> [1] arm-smmu 9000000.iommu: Unhandled context fault: fsr=0x402,
>> iova=0x02180004, fsynr=0x150021, cb=7
>>
>> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
>> ---
>> drivers/i2c/busses/i2c-imx.c | 57 +++++++++++++++++++++++++++++-------
>> 1 file changed, 47 insertions(+), 10 deletions(-)
>>
>> diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
>> index 4e34b1572756..07cc8f4b45b9 100644
>> --- a/drivers/i2c/busses/i2c-imx.c
>> +++ b/drivers/i2c/busses/i2c-imx.c
>> @@ -202,6 +202,9 @@ struct imx_i2c_struct {
>> struct pinctrl_state *pinctrl_pins_gpio;
>> struct imx_i2c_dma *dma;
>> +
>> + dma_addr_t dma_tx_addr;
>> + dma_addr_t dma_rx_addr;
>> };
>> static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
>> @@ -274,17 +277,20 @@ static inline unsigned char
>> imx_i2c_read_reg(struct imx_i2c_struct *i2c_imx,
>> /* Functions for DMA support */
>> static int i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
>> - dma_addr_t phy_addr)
>> + phys_addr_t phy_addr)
>> {
>> struct imx_i2c_dma *dma;
>> struct dma_slave_config dma_sconfig;
>> struct device *dev = &i2c_imx->adapter.dev;
>> int ret;
>> + phys_addr_t i2dr_pa;
>> dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL);
>> if (!dma)
>> return -ENOMEM;
>> + i2dr_pa = phy_addr + (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
>> +
>> dma->chan_tx = dma_request_chan(dev, "tx");
>> if (IS_ERR(dma->chan_tx)) {
>> ret = PTR_ERR(dma->chan_tx);
>> @@ -293,15 +299,25 @@ static int i2c_imx_dma_request(struct
>> imx_i2c_struct *i2c_imx,
>> goto fail_al;
>> }
>> - dma_sconfig.dst_addr = phy_addr +
>> - (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
>> + i2c_imx->dma_tx_addr = dma_map_resource(dma->chan_tx->device->dev,
>> + i2dr_pa,
>> + DMA_SLAVE_BUSWIDTH_1_BYTE,
>> + DMA_MEM_TO_DEV, 0);
>> + ret = dma_mapping_error(dma->chan_tx->device->dev,
>> + i2c_imx->dma_tx_addr);
>> + if (ret) {
>> + dev_err(dev, "can't dma map tx destination (%d)\n", ret);
>> + goto fail_tx;
>> + }
>> +
>> + dma_sconfig.dst_addr = i2c_imx->dma_tx_addr;
>> dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
>> dma_sconfig.dst_maxburst = 1;
>> dma_sconfig.direction = DMA_MEM_TO_DEV;
>> ret = dmaengine_slave_config(dma->chan_tx, &dma_sconfig);
>> if (ret < 0) {
>> dev_err(dev, "can't configure tx channel (%d)\n", ret);
>> - goto fail_tx;
>> + goto fail_tx_dma;
>> }
>> dma->chan_rx = dma_request_chan(dev, "rx");
>> @@ -309,18 +325,28 @@ static int i2c_imx_dma_request(struct
>> imx_i2c_struct *i2c_imx,
>> ret = PTR_ERR(dma->chan_rx);
>> if (ret != -ENODEV && ret != -EPROBE_DEFER)
>> dev_err(dev, "can't request DMA rx channel (%d)\n", ret);
>> - goto fail_tx;
>> + goto fail_tx_dma;
>> }
>> - dma_sconfig.src_addr = phy_addr +
>> - (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
>> + i2c_imx->dma_rx_addr = dma_map_resource(dma->chan_rx->device->dev,
>> + i2dr_pa,
>> + DMA_SLAVE_BUSWIDTH_1_BYTE,
>> + DMA_DEV_TO_MEM, 0);
>> + ret = dma_mapping_error(dma->chan_rx->device->dev,
>> + i2c_imx->dma_rx_addr);
>> + if (ret) {
>> + dev_err(dev, "can't dma map rx source (%d)\n", ret);
>> + goto fail_rx;
>> + }
>> +
>> + dma_sconfig.src_addr = i2c_imx->dma_rx_addr;
>> dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
>> dma_sconfig.src_maxburst = 1;
>> dma_sconfig.direction = DMA_DEV_TO_MEM;
>> ret = dmaengine_slave_config(dma->chan_rx, &dma_sconfig);
>> if (ret < 0) {
>> dev_err(dev, "can't configure rx channel (%d)\n", ret);
>> - goto fail_rx;
>> + goto fail_rx_dma;
>> }
>> i2c_imx->dma = dma;
>> @@ -330,8 +356,14 @@ static int i2c_imx_dma_request(struct
>> imx_i2c_struct *i2c_imx,
>> return 0;
>> +fail_rx_dma:
>> + dma_unmap_resource(dma->chan_rx->device->dev, i2c_imx->dma_rx_addr,
>> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_DEV_TO_MEM, 0);
>> fail_rx:
>> dma_release_channel(dma->chan_rx);
>> +fail_tx_dma:
>> + dma_unmap_resource(dma->chan_tx->device->dev, i2c_imx->dma_tx_addr,
>> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_MEM_TO_DEV, 0);
>> fail_tx:
>> dma_release_channel(dma->chan_tx);
>> fail_al:
>> @@ -1057,7 +1089,7 @@ static int i2c_imx_probe(struct platform_device
>> *pdev)
>> struct imxi2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
>> void __iomem *base;
>> int irq, ret;
>> - dma_addr_t phy_addr;
>> + phys_addr_t phy_addr;
>> dev_dbg(&pdev->dev, "<%s>\n", __func__);
>> @@ -1072,7 +1104,7 @@ static int i2c_imx_probe(struct platform_device
>> *pdev)
>> if (IS_ERR(base))
>> return PTR_ERR(base);
>> - phy_addr = (dma_addr_t)res->start;
>> + phy_addr = res->start;
>> i2c_imx = devm_kzalloc(&pdev->dev, sizeof(*i2c_imx), GFP_KERNEL);
>> if (!i2c_imx)
>> return -ENOMEM;
>> @@ -1220,6 +1252,11 @@ static int i2c_imx_remove(struct
>> platform_device *pdev)
>> pm_runtime_put_noidle(&pdev->dev);
>> pm_runtime_disable(&pdev->dev);
>> + dma_unmap_resource(&pdev->dev, i2c_imx->dma_tx_addr,
>> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_MEM_TO_DEV, 0);
>> + dma_unmap_resource(&pdev->dev, i2c_imx->dma_rx_addr,
>> + DMA_SLAVE_BUSWIDTH_1_BYTE, DMA_DEV_TO_MEM, 0);
>> +
>> return 0;
>> }
>>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-01-17 9:58 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-01-16 16:17 [RFC PATCH] i2c: imx: dma map the i2c data i/o register Laurentiu Tudor
2019-01-16 17:55 ` Robin Murphy
2019-01-17 9:58 ` Laurentiu Tudor
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).