[PATCH v2 42/60] i2c: rk3x: reword according to newest specification

[Wolfram Sang <wsa+renesas@sang-engineering.com>]

Change the wording of this driver wrt. the newest I2C v7 and SMBus 3.2
specifications and replace "master/slave" with more appropriate terms.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
---
 drivers/i2c/busses/i2c-rk3x.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c
index beca61700c89..4ef9bad77b85 100644
--- a/drivers/i2c/busses/i2c-rk3x.c
+++ b/drivers/i2c/busses/i2c-rk3x.c
@@ -28,8 +28,8 @@
 /* Register Map */
 #define REG_CON        0x00 /* control register */
 #define REG_CLKDIV     0x04 /* clock divisor register */
-#define REG_MRXADDR    0x08 /* slave address for REGISTER_TX */
-#define REG_MRXRADDR   0x0c /* slave register address for REGISTER_TX */
+#define REG_MRXADDR    0x08 /* target address for REGISTER_TX */
+#define REG_MRXRADDR   0x0c /* target register address for REGISTER_TX */
 #define REG_MTXCNT     0x10 /* number of bytes to be transmitted */
 #define REG_MRXCNT     0x14 /* number of bytes to be received */
 #define REG_IEN        0x18 /* interrupt enable */
@@ -68,8 +68,8 @@ enum {
 /* REG_IEN/REG_IPD bits */
 #define REG_INT_BTF       BIT(0) /* a byte was transmitted */
 #define REG_INT_BRF       BIT(1) /* a byte was received */
-#define REG_INT_MBTF      BIT(2) /* master data transmit finished */
-#define REG_INT_MBRF      BIT(3) /* master data receive finished */
+#define REG_INT_MBTF      BIT(2) /* controller data transmit finished */
+#define REG_INT_MBRF      BIT(3) /* controller data receive finished */
 #define REG_INT_START     BIT(4) /* START condition generated */
 #define REG_INT_STOP      BIT(5) /* STOP condition generated */
 #define REG_INT_NAKRCV    BIT(6) /* NACK received */
@@ -184,7 +184,7 @@ struct rk3x_i2c_soc_data {
  * @wait: the waitqueue to wait for i2c transfer
  * @busy: the condition for the event to wait for
  * @msg: current i2c message
- * @addr: addr of i2c slave device
+ * @addr: addr of i2c target device
  * @mode: mode of i2c transfer
  * @is_last_msg: flag determines whether it is the last msg in this transfer
  * @state: state of i2c transfer
@@ -979,7 +979,7 @@ static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num)
 	/*
 	 * The I2C adapter can issue a small (len < 4) write packet before
 	 * reading. This speeds up SMBus-style register reads.
-	 * The MRXADDR/MRXRADDR hold the slave address and the slave register
+	 * The MRXADDR/MRXRADDR hold the target address and the target register
 	 * address in this case.
 	 */
 
@@ -1016,7 +1016,7 @@ static int rk3x_i2c_setup(struct rk3x_i2c *i2c, struct i2c_msg *msgs, int num)
 			addr |= 1; /* set read bit */
 
 			/*
-			 * We have to transmit the slave addr first. Use
+			 * We have to transmit the target addr first. Use
 			 * MOD_REGISTER_TX for that purpose.
 			 */
 			i2c->mode = REG_CON_MOD_REGISTER_TX;
@@ -1160,9 +1160,9 @@ static u32 rk3x_i2c_func(struct i2c_adapter *adap)
 }
 
 static const struct i2c_algorithm rk3x_i2c_algorithm = {
-	.master_xfer		= rk3x_i2c_xfer,
-	.master_xfer_atomic	= rk3x_i2c_xfer_polling,
-	.functionality		= rk3x_i2c_func,
+	.xfer = rk3x_i2c_xfer,
+	.xfer_atomic = rk3x_i2c_xfer_polling,
+	.functionality = rk3x_i2c_func,
 };
 
 static const struct rk3x_i2c_soc_data rv1108_soc_data = {
-- 
2.43.0