From: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>
To: "Uwe Kleine-König"
<u.kleine-koenig-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Cc: Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>,
Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>,
linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Mike Looijmans
<milo-software-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>,
Kevin Hilman
<khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org>,
Santosh Shilimkar
<ssantosh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Murali Karicheri <m-karicheri2-l0cyMroinI0@public.gmane.org>
Subject: Re: [PATCH v2 1/5] i2c: i2c-davinci: switch to use platform_get_irq
Date: Wed, 26 Nov 2014 18:28:05 +0200 [thread overview]
Message-ID: <5475FF95.6030502@ti.com> (raw)
In-Reply-To: <20141126155431.GK4431-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
On 11/26/2014 05:54 PM, Uwe Kleine-König wrote:
> Hello Grygorii,
>
> On Wed, Nov 26, 2014 at 03:59:49PM +0200, Grygorii Strashko wrote:
>> Switch Davinci I2C driver to use platform_get_irq(), because
>> it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
>> for requesting IRQ resources any more, as they can be not ready yet
>> in case of DT-boot.
>>
>> CC: Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>
>> CC: Kevin Hilman <khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org>
>> CC: Santosh Shilimkar <ssantosh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>> CC: Murali Karicheri <m-karicheri2-l0cyMroinI0@public.gmane.org>
>> Signed-off-by: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>
>> ---
>> drivers/i2c/busses/i2c-davinci.c | 20 ++++++++++++--------
>> 1 file changed, 12 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
>> index 4d96147..7f54903 100644
>> --- a/drivers/i2c/busses/i2c-davinci.c
>> +++ b/drivers/i2c/busses/i2c-davinci.c
>> @@ -640,13 +640,17 @@ static int davinci_i2c_probe(struct platform_device *pdev)
>> {
>> struct davinci_i2c_dev *dev;
>> struct i2c_adapter *adap;
>> - struct resource *mem, *irq;
>> - int r;
>> -
>> - irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
>> - if (!irq) {
>> - dev_err(&pdev->dev, "no irq resource?\n");
>> - return -ENODEV;
>> + struct resource *mem;
>> + int r, irq;
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq <= 0) {
>> + if (irq == -EPROBE_DEFER)
>> + return irq;
>> + if (!irq)
>> + irq = -ENXIO;
>> + dev_err(&pdev->dev, "can't get irq resource ret=%d\n", irq);
>> + return irq;
> The simpler and I think also more usual logic is:
>
> if (!irq)
> irq = -ENXIO;
> if (irq != -EPROBE_DEFER)
> dev_err(...);
> return irq;
>
> Other than that the patch looks fine.
Ok. will change and add your ack.
regards,
-grygorii
next prev parent reply other threads:[~2014-11-26 16:28 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-11-26 13:59 [PATCH v2 0/5] i2c: davinci improvements and fixes Grygorii Strashko
2014-11-26 13:59 ` [PATCH v2 1/5] i2c: i2c-davinci: switch to use platform_get_irq Grygorii Strashko
[not found] ` <1417010393-30598-2-git-send-email-grygorii.strashko-l0cyMroinI0@public.gmane.org>
2014-11-26 15:54 ` Uwe Kleine-König
[not found] ` <20141126155431.GK4431-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2014-11-26 16:28 ` Grygorii Strashko [this message]
2014-11-26 13:59 ` [PATCH v2 2/5] i2c: davinci: query STP always when NACK is received Grygorii Strashko
[not found] ` <1417010393-30598-3-git-send-email-grygorii.strashko-l0cyMroinI0@public.gmane.org>
2014-11-26 15:57 ` Uwe Kleine-König
2014-11-26 16:31 ` Grygorii Strashko
2014-11-26 17:15 ` Uwe Kleine-König
2014-11-26 13:59 ` [PATCH v2 3/5] i2c: recovery: change input parameter to i2c_adapter for prepare/unprepare_recovery Grygorii Strashko
2014-11-26 13:59 ` [PATCH v2 4/5] i2c: davinci: use bus recovery infrastructure Grygorii Strashko
[not found] ` <1417010393-30598-5-git-send-email-grygorii.strashko-l0cyMroinI0@public.gmane.org>
2014-11-26 15:59 ` Uwe Kleine-König
2014-11-26 13:59 ` [PATCH v2 5/5] i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery Grygorii Strashko
[not found] ` <1417010393-30598-6-git-send-email-grygorii.strashko-l0cyMroinI0@public.gmane.org>
2014-11-26 16:04 ` Uwe Kleine-König
[not found] ` <20141126160407.GN4431-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2014-11-26 17:05 ` Grygorii Strashko
[not found] ` <5476085B.40009-l0cyMroinI0@public.gmane.org>
2015-07-07 13:37 ` Jan Lübbe
[not found] ` <1436276269.3344.94.camel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2015-07-07 13:43 ` Wolfram Sang
2015-07-07 13:48 ` Uwe Kleine-König
[not found] ` <20150707134852.GE9671-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
2015-07-07 14:13 ` Wolfram Sang
2015-07-07 14:53 ` Grygorii Strashko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5475FF95.6030502@ti.com \
--to=grygorii.strashko-l0cymroini0@public.gmane.org \
--cc=khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=m-karicheri2-l0cyMroinI0@public.gmane.org \
--cc=milo-software-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
--cc=nsekhar-l0cyMroinI0@public.gmane.org \
--cc=ssantosh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=u.kleine-koenig-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).