Re: [PATCH 11/13] i2c: cht-wc: Add support for devices using a bq25890 charger

[Yauhen Kharuzhy <jekhor@gmail.com>]

On Sun, Nov 07, 2021 at 10:07:27PM +0300, Yauhen Kharuzhy wrote:
> On Sat, Oct 30, 2021 at 08:28:11PM +0200, Hans de Goede wrote:
> > The i2c-controller on the Cherry Trail - Whiskey Cove PMIC is special
> > in that it is always connected to the I2C charger IC of the board on
> > which the PMIC is used; and the charger IC is not described in ACPI,
> > so the i2c-cht-wc code needs to instantiate an i2c-client for it itself.
> > 
> > So far there has been a rudimentary check to make sure the ACPI tables
> > are at least somewhat as expected by checking for the presence of an
> > INT33FE device and sofar the code has assumed that if this INT33FE
> > device is present that the used charger then is a bq24290i.
> > 
> > But some boards with an INT33FE device in their ACPI tables use a
> > different charger IC and some boards don't have an INT33FE device at all.
> > 
> > Since the information about the used charger + fuel-gauge + other chips is
> > necessary in other places too, the kernel now adds a "intel,cht-wc-setup"
> > string property to the Whiskey Cove PMIC i2c-client based on DMI matching,
> > which reliably describes the board's setup of the PMIC.
> > 
> > Switch to using the "intel,cht-wc-setup" property and add support for
> > instantiating an i2c-client for either a bq24292i or a bq25890 charger.
> > 
> > This has been tested on a GPD pocket (which uses the old bq24292i setup)
> > and on a Xiaomi Mi Pad 2 with a bq25890 charger.
> > 
> > Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> > ---
> >  drivers/i2c/busses/i2c-cht-wc.c | 77 +++++++++++++++++++++++++--------
> >  1 file changed, 59 insertions(+), 18 deletions(-)
> > 
> > diff --git a/drivers/i2c/busses/i2c-cht-wc.c b/drivers/i2c/busses/i2c-cht-wc.c
> > index 1cf68f85b2e1..e7d62af6c39d 100644
> > --- a/drivers/i2c/busses/i2c-cht-wc.c
> > +++ b/drivers/i2c/busses/i2c-cht-wc.c
> > @@ -18,6 +18,7 @@
> >  #include <linux/module.h>
> >  #include <linux/platform_device.h>
> >  #include <linux/power/bq24190_charger.h>
> > +#include <linux/power/bq25890_charger.h>
> >  #include <linux/slab.h>
> >  
> >  #define CHT_WC_I2C_CTRL			0x5e24
> > @@ -304,18 +305,55 @@ static struct bq24190_platform_data bq24190_pdata = {
> >  	.regulator_init_data = &bq24190_vbus_init_data,
> >  };
> >  
> > +static struct i2c_board_info bq24190_board_info = {
> > +	.type = "bq24190",
> > +	.addr = 0x6b,
> > +	.dev_name = "bq24190",
> > +	.swnode = &bq24190_node,
> > +	.platform_data = &bq24190_pdata,
> > +};
> > +
> > +static struct regulator_consumer_supply bq25890_vbus_consumer = {
> > +	.supply = "vbus",
> > +	.dev_name = "cht_wcove_pwrsrc",
> > +};
> > +
> > +static const struct regulator_init_data bq25890_vbus_init_data = {
> > +	.constraints = {
> > +		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
> > +	},
> > +	.consumer_supplies = &bq25890_vbus_consumer,
> > +	.num_consumer_supplies = 1,
> > +};
> > +
> > +static struct bq25890_platform_data bq25890_pdata = {
> > +	.regulator_init_data = &bq25890_vbus_init_data,
> > +};
> > +
> > +static const struct property_entry bq25890_props[] = {
> > +	PROPERTY_ENTRY_BOOL("ti,skip-init"),
> > +	{ }
> > +};
> 
> The Lenovo Yoga Book firmware set the IINLIM field to 500 mA at
> initialization, we need a way to pass maximum allowed current in the fast
> charging mode to driver. I have added 'ti,input-max-current' in my port, for
> example.

ICHG (charging current limit) is too low also (2A versus 4A in Android
sources for this device), so it should be set by properties.

-- 
Yauhen Kharuzhy