* Re: [RFC 7/7] iio: inv_mpu6050: Add support for external sensors
[not found] ` <c2631025b2405ad01c92964ed185d73647593f17.1461953982.git.leonard.crestez@intel.com>
@ 2016-05-01 17:54 ` Jonathan Cameron
0 siblings, 0 replies; 4+ messages in thread
From: Jonathan Cameron @ 2016-05-01 17:54 UTC (permalink / raw)
To: Crestez Dan Leonard, linux-iio@vger.kernel.org
Cc: linux-kernel, Hartmut Knaack, Lars-Peter Clausen,
Peter Meerwald-Stadler, Daniel Baluta, Ge Gao,
devicetree@vger.kernel.org, Mark Rutland, Rob Herring, Pawel Moll,
Ian Campbell, Kumar Gala, Linux I2C, Wolfram Sang, Peter Rosin
On 29/04/16 20:02, Crestez Dan Leonard wrote:
> This works by copying their channels at probe time.
>
> Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
This is some mixture of deeply nefarious and rather cool.
Great bit of work all in all.
Cc'd device tree list and maintainers - to them - this is downright mad
hardware - basically a partial i2c offload engine sitting on either i2c or
spi buses with lots of iritating restrictions but useful stuff like a fifo
between it and the rest of the world - upshot it's much much faster than
actually addressing these devices directly...
First time I read the datasheet for this part - I thought no one would ever
figure out / go to the effort of supporting this functionality. Turns
out I was wrong!
It is the only part I know of allowing this level of flexibility as a sensor
hub. Most sensor hubs hide entirely what is going on behind them whereas this
one exposes what is going on...
Also cc'd the i2c list / Peter, Wolfram and Mark (just because they might be
interested!)
Jonathan
> ---
> .../devicetree/bindings/iio/imu/inv_mpu6050.txt | 37 +-
> drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 420 ++++++++++++++++++++-
> drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h | 63 +++-
> drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c | 48 ++-
> 4 files changed, 555 insertions(+), 13 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
> index aaf12b4..79b8326 100644
> --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
> +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt
> @@ -23,6 +23,28 @@ Devices connected in "bypass" mode must be listed behind i2c@0 with the address
>
> Devices connected in "master" mode must be listed behind i2c@1 with the address 1
>
> +It is possible to configure the MPU to automatically fetch reading for
> +devices connected on the auxiliary i2c bus without CPU intervention. When this
> +is done the driver will present the channels of the slaved devices as if they
> +belong to the MPU device itself.
> +
> +Reads and write to config values (like scaling factors) are forwarded to the
> +other driver while data reads are handled from MPU registers. The channels are
> +also available through the MPU's iio triggered buffer mechanism. This feature
> +can allow sampling up to 24 bytes from 4 slaves at a much higher rate.
> +
> +This is be specified in device tree as an "inv,external-sensors" node which
> +have children indexed by slave ids 0 to 3. The child node identifying each
> +external sensor reading has the following properties:
> + - reg: 0 to 3 slave index
> + - inv,addr : the I2C address to read from
> + - inv,reg : the I2C register to read from
> + - inv,len : read length from the device
> + - inv,external-channels : list of slaved channels specified by config index.
I wonder if we want to try and make these generic - probably not until we have
at least one more device doing something similar...
> +
> +The sum of storagebits for external channels must equal the read length. Only
> +16bit channels are currently supported.
> +
> Example:
> mpu6050@68 {
> compatible = "invensense,mpu6050";
> @@ -61,7 +83,8 @@ Example describing mpu9150 (which includes an ak9875 on chip):
> };
> };
>
> -Example describing a mpu6500 via SPI with an hmc5883l on auxiliary i2c:
> +Example describing a mpu6500 via SPI with an hmc5883l on aux i2c configured for
> +automatic external readings as slave 0:
> mpu6500@0 {
> compatible = "inv,mpu6500";
> reg = <0x0>;
> @@ -80,4 +103,16 @@ Example describing a mpu6500 via SPI with an hmc5883l on auxiliary i2c:
> reg = <0x1e>;
> };
> };
> +
> + inv,external-sensors {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + hmc5833l@0 {
> + reg = <0>;
> + inv,addr = <0x1e>;
> + inv,reg = <3>;
> + inv,len = <6>;
> + inv,external-channels = <0 1 2>;
> + };
> + };
> };
> diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
> index 712e901..224be3c 100644
> --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
> +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
> @@ -41,6 +41,8 @@ static const int gyro_scale_6050[] = {133090, 266181, 532362, 1064724};
> */
> static const int accel_scale[] = {598, 1196, 2392, 4785};
>
> +#define INV_MPU6050_NUM_INT_CHAN 8
> +
> static const struct inv_mpu6050_reg_map reg_set_6500 = {
> .sample_rate_div = INV_MPU6050_REG_SAMPLE_RATE_DIV,
> .lpf = INV_MPU6050_REG_CONFIG,
> @@ -136,6 +138,9 @@ static bool inv_mpu6050_volatile_reg(struct device *dev, unsigned int reg)
> return true;
> if (reg >= INV_MPU6050_REG_RAW_GYRO && reg < INV_MPU6050_REG_RAW_GYRO + 6)
> return true;
> + if (reg < INV_MPU6050_REG_EXT_SENS_DATA_00 + INV_MPU6050_CNT_EXT_SENS_DATA &&
> + reg >= INV_MPU6050_REG_EXT_SENS_DATA_00)
> + return true;
> switch (reg) {
> case INV_MPU6050_REG_TEMPERATURE:
> case INV_MPU6050_REG_TEMPERATURE + 1:
> @@ -340,13 +345,115 @@ static int inv_mpu6050_sensor_show(struct inv_mpu6050_state *st, int reg,
> return IIO_VAL_INT;
> }
>
> +static bool iio_chan_needs_swab(const struct iio_chan_spec *chan)
> +{
> +#if defined(__LITTLE_ENDIAN)
> + return chan->scan_type.endianness == IIO_BE;
> +#elif defined(__BIG_ENDIAN)
> + return chan->scan_type.endianness == IIO_LE;
> +#else
> + #error undefined endianness
> +#endif
> +}
> +
> +/* Convert iio buffer format to IIO_CHAN_INFO_RAW value */
> +static int iio_bufval_to_rawval(const struct iio_chan_spec *chan, void *buf, int *val)
> +{
> + switch (chan->scan_type.storagebits) {
> + case 8: *val = *((u8*)buf); break;
> + case 16: *val = *(u16*)buf; break;
> + case 32: *val = *(u32*)buf; break;
> + default: return -EINVAL;
> + }
> +
> + *val >>= chan->scan_type.shift;
> + *val &= (1 << chan->scan_type.realbits) - 1;
> + if (iio_chan_needs_swab(chan)) {
> + if (chan->scan_type.storagebits == 16)
> + *val = swab16(*val);
> + else if (chan->scan_type.storagebits == 32)
> + *val = swab32(*val);
This needs some explanatory comments!
> + }
> + if (chan->scan_type.sign == 's')
> + *val = sign_extend32(*val, chan->scan_type.storagebits - 1);
> +
> + return 0;
> +}
> +
> +static int
> +inv_mpu6050_read_raw_external(struct iio_dev *indio_dev,
> + struct iio_chan_spec const *chan,
> + int *val, int *val2, long mask)
> +{
> + int result;
> + struct inv_mpu6050_state *st = iio_priv(indio_dev);
> + int chan_index = chan - indio_dev->channels;
> + struct inv_mpu6050_ext_chan_state *ext_chan_state =
> + &st->ext_chan[chan_index - INV_MPU6050_NUM_INT_CHAN];
> + struct inv_mpu6050_ext_sens_state *ext_sens_state =
> + &st->ext_sens[ext_chan_state->ext_sens_index];
> + struct iio_dev *orig_dev = ext_sens_state->orig_dev;
> + const struct iio_chan_spec *orig_chan = &orig_dev->channels[ext_chan_state->orig_chan_index];
> + int data_offset;
> + int data_length;
> + u8 buf[4];
> +
> + /* Everything but raw data reads is forwarded. */
> + if (mask != IIO_CHAN_INFO_RAW)
> + return orig_dev->info->read_raw(orig_dev, orig_chan, val, val2, mask);
Obviously this is useful for testing, but on a polled interface do we actually
care that it is quicker to go directly? I'd be tempted to not bother except
for the buffered mode.
> +
> + /* Raw reads are handled directly. */
> + data_offset = INV_MPU6050_REG_EXT_SENS_DATA_00 + ext_chan_state->data_offset;
> + data_length = chan->scan_type.storagebits / 8;
> + if (data_length > sizeof(buf)) {
> + return -EINVAL;
> + }
> +
> + mutex_lock(&indio_dev->mlock);
> + if (!st->chip_config.enable) {
> + result = inv_mpu6050_set_power_itg(st, true);
> + if (result)
> + goto error_unlock;
> + }
> + result = regmap_bulk_read(st->map, data_offset, buf, data_length);
> + if (result)
> + goto error_unpower;
> + if (!st->chip_config.enable) {
> + result = inv_mpu6050_set_power_itg(st, false);
> + if (result)
> + goto error_unlock;
> + }
> + mutex_unlock(&indio_dev->mlock);
> +
> + /* Convert buf to val and return success */
> + result = iio_bufval_to_rawval(chan, buf, val);
> + if (result)
> + return result;
> + return IIO_VAL_INT;
> +
> +error_unpower:
> + if (!st->chip_config.enable)
> + inv_mpu6050_set_power_itg(st, false);
> +error_unlock:
> + mutex_unlock(&indio_dev->mlock);
> + return result;
> +}
> +
> static int
> inv_mpu6050_read_raw(struct iio_dev *indio_dev,
> struct iio_chan_spec const *chan,
> int *val, int *val2, long mask)
> {
> - struct inv_mpu6050_state *st = iio_priv(indio_dev);
> + struct inv_mpu6050_state *st = iio_priv(indio_dev);
> int ret = 0;
> + int chan_index;
> +
> + if (chan < indio_dev->channels || chan > indio_dev->channels + indio_dev->num_channels) {
> + return -EINVAL;
> + }
> + chan_index = chan - indio_dev->channels;
> + if (chan_index >= INV_MPU6050_NUM_INT_CHAN)
> + return inv_mpu6050_read_raw_external(indio_dev, chan, val, val2, mask);
>
> switch (mask) {
> case IIO_CHAN_INFO_RAW:
> @@ -819,6 +926,309 @@ static const struct iio_info mpu_info = {
> .validate_trigger = inv_mpu6050_validate_trigger,
> };
>
> +extern struct device_type iio_device_type;
> +
> +static int iio_device_from_i2c_client_match(struct device *dev, void *data)
> +{
> + return dev->type == &iio_device_type;
> +}
> +
> +static struct iio_dev* iio_device_from_i2c_client(struct i2c_client* i2c)
> +{
> + struct device *child;
> +
> + child = device_find_child(&i2c->dev, NULL, iio_device_from_i2c_client_match);
> +
> + return (child ? dev_to_iio_dev(child) : NULL);
> +}
> +
> +static int inv_mpu_set_external_reads_enabled(struct inv_mpu6050_state *st, bool en)
> +{
> + int i, result, error = 0;
> +
> + /* Even if there are errors try to disable all slaves. */
> + for (i = 0; i < INV_MPU6050_MAX_EXT_SENSORS; ++i) {
> + result = regmap_update_bits(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(i),
> + INV_MPU6050_BIT_I2C_SLV_EN,
> + en ? INV_MPU6050_BIT_I2C_SLV_EN : 0);
> + if (result) {
> + error = result;
> + }
> + }
> +
> + return error;
> +}
> +
> +static int inv_mpu_parse_one_ext_sens(struct device *dev,
> + struct device_node *np,
> + struct inv_mpu6050_ext_sens_spec *spec)
> +{
> + int result;
> + u32 addr, reg, len;
> +
> + result = of_property_read_u32(np, "inv,addr", &addr);
> + if (result)
> + return result;
> + result = of_property_read_u32(np, "inv,reg", ®);
> + if (result)
> + return result;
> + result = of_property_read_u32(np, "inv,len", &len);
> + if (result)
> + return result;
> +
> + spec->addr = addr;
> + spec->reg = reg;
> + spec->len = len;
> +
> + result = of_property_count_u32_elems(np, "inv,external-channels");
> + if (result < 0)
> + return result;
> + spec->num_ext_channels = result;
> + spec->ext_channels = devm_kmalloc(dev, spec->num_ext_channels * sizeof(*spec->ext_channels), GFP_KERNEL);
> + if (!spec->ext_channels)
> + return -ENOMEM;
> + result = of_property_read_u32_array(np, "inv,external-channels",
> + spec->ext_channels,
> + spec->num_ext_channels);
> + if (result)
> + return result;
> +
> + return 0;
> +}
> +
> +static int inv_mpu_parse_ext_sens(struct device *dev,
> + struct device_node *node,
> + struct inv_mpu6050_ext_sens_spec *specs)
> +{
> + struct device_node *child;
> + int result;
> + u32 reg;
> +
> + for_each_available_child_of_node(node, child) {
> + result = of_property_read_u32(child, "reg", ®);
> + if (result)
> + return result;
> + if (reg > INV_MPU6050_MAX_EXT_SENSORS) {
> + dev_err(dev, "External sensor index %u out of range, max %d\n",
> + reg, INV_MPU6050_MAX_EXT_SENSORS);
> + return -EINVAL;
> + }
> + result = inv_mpu_parse_one_ext_sens(dev, child, &specs[reg]);
> + if (result)
> + return result;
> + }
> +
> + return 0;
> +}
> +
> +static int inv_mpu_get_ext_sens_spec(struct iio_dev *indio_dev)
> +{
> + struct inv_mpu6050_state *st = iio_priv(indio_dev);
> + struct device *dev = regmap_get_device(st->map);
> + struct device_node *node;
> + int result;
> +
> + node = of_get_child_by_name(dev->of_node, "inv,external-sensors");
> + if (node) {
> + result = inv_mpu_parse_ext_sens(dev, node, st->ext_sens_spec);
> + if (result)
> + dev_err(dev, "Failed to parsing external-sensors devicetree data\n");
> + return result;
> + }
> +
> + /* Maybe some other way to deal with this? */
Probably not ;)
> +
> + return 0;
> +}
> +
> +/* Struct used while enumerating devices and matching them */
> +struct inv_mpu_handle_ext_sensor_fnarg
> +{
> + struct iio_dev *indio_dev;
> +
> + /* Next scan index */
> + int scan_index;
> + /* Index among external channels */
> + int chan_index;
> + /* Offset in EXTDATA */
> + int data_offset;
> + struct iio_chan_spec *channels;
> +};
> +
> +static int inv_mpu_config_external_read(struct inv_mpu6050_state *st, int index,
> + const struct inv_mpu6050_ext_sens_spec *spec)
> +{
> + int result;
> +
> + result = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_ADDR(index),
> + INV_MPU6050_BIT_I2C_SLV_RW | spec->addr);
> + if (result)
> + return result;
> + result = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_REG(index), spec->reg);
> + if (result)
> + return result;
> + result = regmap_write(st->map, INV_MPU6050_REG_I2C_SLV_CTRL(index),
> + INV_MPU6050_BIT_I2C_SLV_EN | spec->len);
> +
> + return result;
> +}
> +
> +static int inv_mpu_handle_ext_sensor_fn(struct device *dev, void *data)
> +{
> + struct inv_mpu_handle_ext_sensor_fnarg *fnarg = data;
> + struct iio_dev *indio_dev = fnarg->indio_dev;
> + struct inv_mpu6050_state *st = iio_priv(indio_dev);
> + struct device *mydev = regmap_get_device(st->map);
> + struct i2c_client *client;
> + struct iio_dev *orig_dev;
> + int i, j;
> +
> + client = i2c_verify_client(dev);
> + if (!client)
> + return 0;
> + orig_dev = iio_device_from_i2c_client(client);
> + if (!orig_dev)
> + return 0;
> + for (i = 0; i < INV_MPU6050_MAX_EXT_SENSORS; ++i) {
> + int start_data_offset;
> + struct inv_mpu6050_ext_sens_spec *ext_sens_spec = &st->ext_sens_spec[i];
> + struct inv_mpu6050_ext_sens_state *ext_sens_state = &st->ext_sens[i];
> +
> + if (ext_sens_spec->addr != client->addr)
> + continue;
> + if (ext_sens_state->orig_dev) {
> + dev_warn(&indio_dev->dev, "already found slave with at addr %d\n", client->addr);
> + continue;
> + }
> + dev_info(mydev, "external sensor %d is device %s\n",
> + i, orig_dev->name ?: dev_name(&orig_dev->dev));
> + ext_sens_state->orig_dev = orig_dev;
> + ext_sens_state->scan_mask = 0;
> + ext_sens_state->data_len = ext_sens_spec->len;
> + start_data_offset = fnarg->data_offset;
> +
> + /* Matched the device (by address). Now process channels: */
> + for (j = 0; j < ext_sens_spec->num_ext_channels; ++j) {
> + int orig_chan_index;
> + const struct iio_chan_spec *orig_chan_spec;
> + struct iio_chan_spec *chan_spec;
> + struct inv_mpu6050_ext_chan_state *chan_state;
> +
> + orig_chan_index = ext_sens_spec->ext_channels[j];
> + orig_chan_spec = &orig_dev->channels[orig_chan_index];
> + chan_spec = &fnarg->channels[INV_MPU6050_NUM_INT_CHAN + fnarg->chan_index];
> + chan_state = &st->ext_chan[fnarg->chan_index];
> +
> + chan_state->ext_sens_index = i;
> + chan_state->orig_chan_index = orig_chan_index;
> + chan_state->data_offset = fnarg->data_offset;
> + memcpy(chan_spec, orig_chan_spec, sizeof(struct iio_chan_spec));
> + chan_spec->scan_index = fnarg->scan_index;
> + ext_sens_state->scan_mask |= (1 << chan_spec->scan_index);
> + if (orig_chan_spec->scan_type.storagebits != 16) {
> + /*
> + * Supporting other channels sizes would require data read from the
> + * hardware fifo to comply with iio alignment.
> + */
Or a demux/mux before iio_push_to_buffers.
> + dev_err(&indio_dev->dev, "All external channels must have 16 storage bits\n");
> + return -EINVAL;
> + }
> +
> + fnarg->scan_index++;
> + fnarg->chan_index++;
> + fnarg->data_offset += chan_spec->scan_type.storagebits / 8;
> + dev_info(mydev, "Reading external channel #%d scan_index %d data_offset %d"
> + " from original device %s chan #%d scan_index %d\n",
> + fnarg->chan_index, chan_spec->scan_index, chan_state->data_offset,
> + orig_dev->name ?: dev_name(&orig_dev->dev), orig_chan_index, orig_chan_spec->scan_index);
> + }
> + if (start_data_offset + ext_sens_spec->len != fnarg->data_offset) {
> + dev_warn(mydev, "length mismatch between i2c slave read length and slave channel spec\n");
> + return -EINVAL;
> + }
> +
> + return inv_mpu_config_external_read(st, i, ext_sens_spec);
> + }
> + return 0;
> +}
> +
> +static int inv_mpu6050_handle_ext_sensors(struct iio_dev *indio_dev)
> +{
> + struct inv_mpu6050_state *st = iio_priv(indio_dev);
> + struct device *dev = regmap_get_device(st->map);
> + struct inv_mpu_handle_ext_sensor_fnarg fnarg = {
> + .indio_dev = indio_dev,
> + .chan_index = 0,
> + .data_offset = 0,
> + .scan_index = INV_MPU6050_SCAN_TIMESTAMP,
> + };
> + int i, result;
> + int num_ext_chan = 0, sum_data_len = 0;
> +
> + inv_mpu_get_ext_sens_spec(indio_dev);
> + for (i = 0; i < INV_MPU6050_MAX_EXT_SENSORS; ++i) {
> + num_ext_chan += st->ext_sens_spec[i].num_ext_channels;
> + sum_data_len += st->ext_sens_spec[i].len;
> + }
> + if (sum_data_len > INV_MPU6050_CNT_EXT_SENS_DATA) {
> + dev_err(dev, "Too many bytes from external sensors:"
> + " requested=%d max=%d\n",
> + sum_data_len, INV_MPU6050_CNT_EXT_SENS_DATA);
> + return -EINVAL;
> + }
> +
> + /* Zero length means nothing to do */
> + if (!sum_data_len) {
> + indio_dev->channels = inv_mpu_channels;
> + indio_dev->num_channels = INV_MPU6050_NUM_INT_CHAN;
> + BUILD_BUG_ON(ARRAY_SIZE(inv_mpu_channels) != INV_MPU6050_NUM_INT_CHAN);
> + return 0;
> + }
> +
> + fnarg.channels = devm_kmalloc(indio_dev->dev.parent,
> + (num_ext_chan + INV_MPU6050_NUM_INT_CHAN) *
> + sizeof(struct iio_chan_spec),
> + GFP_KERNEL);
> + if (!fnarg.channels)
> + return -ENOMEM;
> + memcpy(fnarg.channels, inv_mpu_channels, sizeof(inv_mpu_channels));
> + memset(fnarg.channels + INV_MPU6050_NUM_INT_CHAN, 0,
> + num_ext_chan * sizeof(struct iio_chan_spec));
> +
> + st->ext_chan = devm_kzalloc(indio_dev->dev.parent,
> + (num_ext_chan) * sizeof(*st->ext_chan),
> + GFP_KERNEL);
> + if (!st->ext_chan)
> + return -ENOMEM;
> +
> + result = inv_mpu6050_set_power_itg(st, true);
> + if (result < 0)
> + return result;
> +
> + result = device_for_each_child(&st->aux_master_adapter.dev, &fnarg,
> + inv_mpu_handle_ext_sensor_fn);
> + if (result)
> + goto out_disable;
> + /* Timestamp channel has index 0 and last scan_index */
> + fnarg.channels[0].scan_index = fnarg.scan_index;
> +
> + if (fnarg.chan_index != num_ext_chan) {
> + dev_err(&indio_dev->dev, "Failed to match all external channels!\n");
> + result = -EINVAL;
> + goto out_disable;
> + }
> +
> + result = inv_mpu6050_set_power_itg(st, false);
> + indio_dev->channels = fnarg.channels;
> + indio_dev->num_channels = INV_MPU6050_NUM_INT_CHAN + num_ext_chan;
> + return result;
> +
> +out_disable:
> + inv_mpu6050_set_power_itg(st, false);
> + inv_mpu_set_external_reads_enabled(st, false);
> + return result;
> +}
> +
> /**
> * inv_check_and_setup_chip() - check and setup chip.
> */
> @@ -1121,8 +1531,6 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name,
> indio_dev->name = name;
> else
> indio_dev->name = dev_name(dev);
> - indio_dev->channels = inv_mpu_channels;
> - indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels);
>
> indio_dev->info = &mpu_info;
> indio_dev->modes = INDIO_BUFFER_TRIGGERED;
> @@ -1160,6 +1568,12 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name,
> }
> #endif
>
> + result = inv_mpu6050_handle_ext_sensors(indio_dev);
> + if (result < 0) {
> + dev_err(dev, "failed to configure channels %d\n", result);
> + goto out_remove_trigger;
> + }
> +
> INIT_KFIFO(st->timestamps);
> spin_lock_init(&st->time_stamp_lock);
> result = iio_device_register(indio_dev);
> diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
> index 9d406df..007fe75 100644
> --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
> +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
> @@ -124,6 +124,40 @@ struct inv_mpu6050_hw {
> const struct inv_mpu6050_chip_config *config;
> };
>
> +#define INV_MPU6050_MAX_EXT_SENSORS 4
> +
> +/* Specification for an external sensor */
> +struct inv_mpu6050_ext_sens_spec {
> + unsigned short addr;
> + u8 reg, len;
> +
> + int num_ext_channels;
> + int *ext_channels;
> +};
> +
> +/* Driver state for each external sensor */
> +struct inv_mpu6050_ext_sens_state {
> + struct iio_dev *orig_dev;
> +
> + /* Mask of all channels in this sensor */
> + unsigned long scan_mask;
> +
> + /* Length of reading. */
> + int data_len;
> +};
> +
> +/* Driver state for each external channel */
> +struct inv_mpu6050_ext_chan_state {
> + /* Index inside state->ext_sens */
> + int ext_sens_index;
> +
> + /* Index inside orig_dev->channels */
> + int orig_chan_index;
> +
> + /* Relative to EXT_SENS_DATA_00 */
> + int data_offset;
> +};
> +
> /*
> * struct inv_mpu6050_state - Driver state variables.
> * @TIMESTAMP_FIFO_SIZE: fifo size for timestamp.
> @@ -164,6 +198,10 @@ struct inv_mpu6050_state {
> struct i2c_adapter aux_master_adapter;
> struct completion slv4_done;
> #endif
> +
> + struct inv_mpu6050_ext_sens_spec ext_sens_spec[INV_MPU6050_MAX_EXT_SENSORS];
> + struct inv_mpu6050_ext_sens_state ext_sens[INV_MPU6050_MAX_EXT_SENSORS];
> + struct inv_mpu6050_ext_chan_state *ext_chan;
> };
>
> /*register and associated bit definition*/
> @@ -178,6 +216,24 @@ struct inv_mpu6050_state {
> #define INV_MPU6050_REG_FIFO_EN 0x23
> #define INV_MPU6050_BIT_ACCEL_OUT 0x08
> #define INV_MPU6050_BITS_GYRO_OUT 0x70
> +#define INV_MPU6050_BIT_SLV0_FIFO_EN 0x01
> +#define INV_MPU6050_BIT_SLV1_FIFO_EN 0x02
> +#define INV_MPU6050_BIT_SLV2_FIFO_EN 0x04
> +#define INV_MPU6050_BIT_SLV2_FIFO_EN 0x04
> +
> +/* SLV3 fifo enabling is not in REG_FIFO_EN */
> +#define INV_MPU6050_REG_MST_CTRL 0x24
> +#define INV_MPU6050_BIT_SLV3_FIFO_EN 0x10
> +
> +/* For slaves 0-3 */
> +#define INV_MPU6050_REG_I2C_SLV_ADDR(i) (0x25 + 3 * (i))
> +#define INV_MPU6050_REG_I2C_SLV_REG(i) (0x26 + 3 * (i))
> +#define INV_MPU6050_REG_I2C_SLV_CTRL(i) (0x27 + 3 * (i))
> +#define INV_MPU6050_BIT_I2C_SLV_RW 0x80
> +#define INV_MPU6050_BIT_I2C_SLV_EN 0x80
> +#define INV_MPU6050_BIT_I2C_SLV_BYTE_SW 0x40
> +#define INV_MPU6050_BIT_I2C_SLV_REG_DIS 0x20
> +#define INV_MPU6050_BIT_I2C_SLV_REG_GRP 0x10
>
> #define INV_MPU6050_REG_I2C_SLV4_ADDR 0x31
> #define INV_MPU6050_BIT_I2C_SLV4_R 0x80
> @@ -252,8 +308,8 @@ struct inv_mpu6050_state {
> #define INV_MPU6050_GYRO_CONFIG_FSR_SHIFT 3
> #define INV_MPU6050_ACCL_CONFIG_FSR_SHIFT 3
>
> -/* 6 + 6 round up and plus 8 */
> -#define INV_MPU6050_OUTPUT_DATA_SIZE 24
> +/* max is 3*2 accel + 3*2 gyro + 24 external + 8 ts */
> +#define INV_MPU6050_OUTPUT_DATA_SIZE 44
>
> #define INV_MPU6050_REG_INT_PIN_CFG 0x37
> #define INV_MPU6050_BIT_BYPASS_EN 0x2
> @@ -266,6 +322,9 @@ struct inv_mpu6050_state {
> #define INV_MPU6050_MIN_FIFO_RATE 4
> #define INV_MPU6050_ONE_K_HZ 1000
>
> +#define INV_MPU6050_REG_EXT_SENS_DATA_00 0x49
> +#define INV_MPU6050_CNT_EXT_SENS_DATA 24
> +
> #define INV_MPU6050_REG_WHOAMI 117
>
> #define INV_MPU6000_WHOAMI_VALUE 0x68
> diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
> index e8bda7f..8fa5c3d 100644
> --- a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
> +++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
> @@ -52,6 +52,10 @@ int inv_reset_fifo(struct iio_dev *indio_dev)
> result = regmap_write(st->map, st->reg->fifo_en, 0);
> if (result)
> goto reset_fifo_fail;
> + result = regmap_update_bits(st->map, INV_MPU6050_REG_MST_CTRL,
> + INV_MPU6050_BIT_SLV3_FIFO_EN, 0);
> + if (result)
> + goto reset_fifo_fail;
> /* disable fifo reading */
> st->chip_config.user_ctrl &= ~INV_MPU6050_BIT_FIFO_EN;
> result = regmap_write(st->map, st->reg->user_ctrl,
> @@ -70,7 +74,8 @@ int inv_reset_fifo(struct iio_dev *indio_dev)
>
> /* enable interrupt */
> if (st->chip_config.accl_fifo_enable ||
> - st->chip_config.gyro_fifo_enable) {
> + st->chip_config.gyro_fifo_enable ||
> + true) {
> result = regmap_update_bits(st->map, st->reg->int_enable,
> INV_MPU6050_BIT_DATA_RDY_EN,
> INV_MPU6050_BIT_DATA_RDY_EN);
> @@ -89,10 +94,23 @@ int inv_reset_fifo(struct iio_dev *indio_dev)
> d |= INV_MPU6050_BITS_GYRO_OUT;
> if (st->chip_config.accl_fifo_enable)
> d |= INV_MPU6050_BIT_ACCEL_OUT;
> + if (*indio_dev->active_scan_mask & st->ext_sens[0].scan_mask)
> + d |= INV_MPU6050_BIT_SLV0_FIFO_EN;
> + if (*indio_dev->active_scan_mask & st->ext_sens[1].scan_mask)
> + d |= INV_MPU6050_BIT_SLV1_FIFO_EN;
> + if (*indio_dev->active_scan_mask & st->ext_sens[2].scan_mask)
> + d |= INV_MPU6050_BIT_SLV2_FIFO_EN;
> result = regmap_write(st->map, st->reg->fifo_en, d);
> if (result)
> goto reset_fifo_fail;
> -
> + if (*indio_dev->active_scan_mask & st->ext_sens[3].scan_mask)
> + {
> + result = regmap_update_bits(st->map, INV_MPU6050_REG_MST_CTRL,
> + INV_MPU6050_BIT_SLV3_FIFO_EN,
> + INV_MPU6050_BIT_SLV3_FIFO_EN);
> + if (result)
> + goto reset_fifo_fail;
> + }
> return 0;
>
> reset_fifo_fail:
> @@ -129,8 +147,9 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p)
> struct iio_poll_func *pf = p;
> struct iio_dev *indio_dev = pf->indio_dev;
> struct inv_mpu6050_state *st = iio_priv(indio_dev);
> - size_t bytes_per_datum;
> + size_t bytes_per_datum = 0;
> int result;
> + int i;
> u8 data[INV_MPU6050_OUTPUT_DATA_SIZE];
> u16 fifo_count;
> s64 timestamp;
> @@ -143,15 +162,18 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p)
> spi = i2c ? NULL: to_spi_device(regmap_dev);
>
> mutex_lock(&indio_dev->mlock);
> - if (!(st->chip_config.accl_fifo_enable |
> - st->chip_config.gyro_fifo_enable))
> - goto end_session;
> +
> + /* Compute bytes_per_datum */
> bytes_per_datum = 0;
> if (st->chip_config.accl_fifo_enable)
> bytes_per_datum += INV_MPU6050_BYTES_PER_3AXIS_SENSOR;
> -
> if (st->chip_config.gyro_fifo_enable)
> bytes_per_datum += INV_MPU6050_BYTES_PER_3AXIS_SENSOR;
> + for (i = 0; i < INV_MPU6050_MAX_EXT_SENSORS; ++i)
> + if (st->ext_sens[i].scan_mask & *indio_dev->active_scan_mask)
> + bytes_per_datum += st->ext_sens[i].data_len;
> + if (!bytes_per_datum)
> + return 0;
>
> /*
> * read fifo_count register to know how many bytes inside FIFO
> @@ -228,6 +250,7 @@ static int inv_mpu_buffer_preenable(struct iio_dev *indio_dev)
> {
> struct inv_mpu6050_state *st = iio_priv(indio_dev);
> unsigned long mask = *indio_dev->active_scan_mask;
> + int i;
>
> if ((mask & INV_MPU6050_SCAN_MASK_GYRO) &&
> (mask & INV_MPU6050_SCAN_MASK_GYRO) != INV_MPU6050_SCAN_MASK_GYRO)
> @@ -245,6 +268,17 @@ static int inv_mpu_buffer_preenable(struct iio_dev *indio_dev)
> return -EINVAL;
> }
>
> + for (i = 0; i < INV_MPU6050_MAX_EXT_SENSORS; ++i) {
> + if ((mask & st->ext_sens[i].scan_mask) &&
> + (mask & st->ext_sens[i].scan_mask) != st->ext_sens[i].scan_mask)
> + {
> + dev_warn(regmap_get_device(st->map),
> + "External channels from the same reading "
> + "can only be enabled together\n");
> + return -EINVAL;
> + }
> + }
> +
> return 0;
> }
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread