* Re: [PATCH] [media] ov5645: I2C address change [not found] ` <20171004103008.g7azpn4a3hfj4fs2@valkosipuli.retiisi.org.uk> @ 2017-10-04 10:47 ` Laurent Pinchart 2017-10-09 8:36 ` Todor Tomov 0 siblings, 1 reply; 6+ messages in thread From: Laurent Pinchart @ 2017-10-04 10:47 UTC (permalink / raw) To: Sakari Ailus Cc: Todor Tomov, mchehab, hansverk, linux-media, linux-kernel, linux-i2c, Wolfram Sang CC'ing the I2C mainling list and the I2C maintainer. On Wednesday, 4 October 2017 13:30:08 EEST Sakari Ailus wrote: > Hi Todor, > > On Mon, Oct 02, 2017 at 04:28:45PM +0300, Todor Tomov wrote: > > As soon as the sensor is powered on, change the I2C address to the one > > specified in DT. This allows to use multiple physical sensors connected > > to the same I2C bus. > > > > Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > > The smiapp driver does something similar and I understand Laurent might be > interested in such functionality as well. > > It'd be nice to handle this through the I²C framework instead and to define > how the information is specified through DT. That way it could be made > generic, to work with more devices than just this one. > > What do you think? > > Cc Laurent. > > > --- > > > > drivers/media/i2c/ov5645.c | 42 ++++++++++++++++++++++++++++++++++++++++ > > 1 file changed, 42 insertions(+) > > > > diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c > > index d28845f..8541109 100644 > > --- a/drivers/media/i2c/ov5645.c > > +++ b/drivers/media/i2c/ov5645.c > > @@ -33,6 +33,7 @@ > > #include <linux/i2c.h> > > #include <linux/init.h> > > #include <linux/module.h> > > +#include <linux/mutex.h> > > #include <linux/of.h> > > #include <linux/of_graph.h> > > #include <linux/regulator/consumer.h> > > @@ -42,6 +43,8 @@ > > #include <media/v4l2-fwnode.h> > > #include <media/v4l2-subdev.h> > > > > +static DEFINE_MUTEX(ov5645_lock); > > + > > #define OV5645_VOLTAGE_ANALOG 2800000 > > #define OV5645_VOLTAGE_DIGITAL_CORE 1500000 > > #define OV5645_VOLTAGE_DIGITAL_IO 1800000 > > @@ -590,6 +593,31 @@ static void ov5645_regulators_disable(struct ov5645 > > *ov5645) > > dev_err(ov5645->dev, "io regulator disable failed\n"); > > } > > > > +static int ov5645_write_reg_to(struct ov5645 *ov5645, u16 reg, u8 val, > > + u16 i2c_addr) > > +{ > > + u8 regbuf[3] = { > > + reg >> 8, > > + reg & 0xff, > > + val > > + }; > > + struct i2c_msg msgs = { > > + .addr = i2c_addr, > > + .flags = 0, > > + .len = 3, > > + .buf = regbuf > > + }; > > + int ret; > > + > > + ret = i2c_transfer(ov5645->i2c_client->adapter, &msgs, 1); > > + if (ret < 0) > > + dev_err(ov5645->dev, > > + "%s: write reg error %d on addr 0x%x: reg=0x%x, val=0x%x\n", > > + __func__, ret, i2c_addr, reg, val); > > + > > + return ret; > > +} > > + > > static int ov5645_write_reg(struct ov5645 *ov5645, u16 reg, u8 val) > > { > > u8 regbuf[3]; > > @@ -729,10 +757,24 @@ static int ov5645_s_power(struct v4l2_subdev *sd, > > int on) > > */ > > if (ov5645->power_count == !on) { > > if (on) { > > + mutex_lock(&ov5645_lock); > > + > > ret = ov5645_set_power_on(ov5645); > > if (ret < 0) > > goto exit; > > > > + ret = ov5645_write_reg_to(ov5645, 0x3100, > > + ov5645->i2c_client->addr, 0x78); > > + if (ret < 0) { > > + dev_err(ov5645->dev, > > + "could not change i2c address\n"); > > + ov5645_set_power_off(ov5645); > > + mutex_unlock(&ov5645_lock); > > + goto exit; > > + } > > + > > + mutex_unlock(&ov5645_lock); > > + > > ret = ov5645_set_register_array(ov5645, > > ov5645_global_init_setting, > > ARRAY_SIZE(ov5645_global_init_setting)); -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] [media] ov5645: I2C address change 2017-10-04 10:47 ` [PATCH] [media] ov5645: I2C address change Laurent Pinchart @ 2017-10-09 8:36 ` Todor Tomov 2017-10-09 9:34 ` Sakari Ailus 0 siblings, 1 reply; 6+ messages in thread From: Todor Tomov @ 2017-10-09 8:36 UTC (permalink / raw) To: Sakari Ailus Cc: Laurent Pinchart, mchehab, hansverk, linux-media, linux-kernel, linux-i2c, Wolfram Sang Hi Sakari, On 4.10.2017 13:47, Laurent Pinchart wrote: > CC'ing the I2C mainling list and the I2C maintainer. > > On Wednesday, 4 October 2017 13:30:08 EEST Sakari Ailus wrote: >> Hi Todor, >> >> On Mon, Oct 02, 2017 at 04:28:45PM +0300, Todor Tomov wrote: >>> As soon as the sensor is powered on, change the I2C address to the one >>> specified in DT. This allows to use multiple physical sensors connected >>> to the same I2C bus. >>> >>> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> >> >> The smiapp driver does something similar and I understand Laurent might be >> interested in such functionality as well. >> >> It'd be nice to handle this through the I²C framework instead and to define >> how the information is specified through DT. That way it could be made >> generic, to work with more devices than just this one. >> >> What do you think? Thank you for this suggestion. The way I have done it is to put the new I2C address in the DT and the driver programs the change using the original I2C address. The original I2C address is hardcoded in the driver. So maybe we can extend the DT binding and the I2C framework so that both addresses come from the DT and avoid hiding the original I2C address in the driver. This sounds good to me. Then changing the address could be device specific and also this must be done right after power on so that there are no address conflicts. So I don't think that we can support this through the I2C framework only, the drivers that we want to do that will have to be expanded with this functionality. Or do you have any other idea? Best regards, Todor >> >> Cc Laurent. >> >>> --- >>> >>> drivers/media/i2c/ov5645.c | 42 ++++++++++++++++++++++++++++++++++++++++ >>> 1 file changed, 42 insertions(+) >>> >>> diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c >>> index d28845f..8541109 100644 >>> --- a/drivers/media/i2c/ov5645.c >>> +++ b/drivers/media/i2c/ov5645.c >>> @@ -33,6 +33,7 @@ >>> #include <linux/i2c.h> >>> #include <linux/init.h> >>> #include <linux/module.h> >>> +#include <linux/mutex.h> >>> #include <linux/of.h> >>> #include <linux/of_graph.h> >>> #include <linux/regulator/consumer.h> >>> @@ -42,6 +43,8 @@ >>> #include <media/v4l2-fwnode.h> >>> #include <media/v4l2-subdev.h> >>> >>> +static DEFINE_MUTEX(ov5645_lock); >>> + >>> #define OV5645_VOLTAGE_ANALOG 2800000 >>> #define OV5645_VOLTAGE_DIGITAL_CORE 1500000 >>> #define OV5645_VOLTAGE_DIGITAL_IO 1800000 >>> @@ -590,6 +593,31 @@ static void ov5645_regulators_disable(struct ov5645 >>> *ov5645) >>> dev_err(ov5645->dev, "io regulator disable failed\n"); >>> } >>> >>> +static int ov5645_write_reg_to(struct ov5645 *ov5645, u16 reg, u8 val, >>> + u16 i2c_addr) >>> +{ >>> + u8 regbuf[3] = { >>> + reg >> 8, >>> + reg & 0xff, >>> + val >>> + }; >>> + struct i2c_msg msgs = { >>> + .addr = i2c_addr, >>> + .flags = 0, >>> + .len = 3, >>> + .buf = regbuf >>> + }; >>> + int ret; >>> + >>> + ret = i2c_transfer(ov5645->i2c_client->adapter, &msgs, 1); >>> + if (ret < 0) >>> + dev_err(ov5645->dev, >>> + "%s: write reg error %d on addr 0x%x: reg=0x%x, val=0x%x\n", >>> + __func__, ret, i2c_addr, reg, val); >>> + >>> + return ret; >>> +} >>> + >>> static int ov5645_write_reg(struct ov5645 *ov5645, u16 reg, u8 val) >>> { >>> u8 regbuf[3]; >>> @@ -729,10 +757,24 @@ static int ov5645_s_power(struct v4l2_subdev *sd, >>> int on) >>> */ >>> if (ov5645->power_count == !on) { >>> if (on) { >>> + mutex_lock(&ov5645_lock); >>> + >>> ret = ov5645_set_power_on(ov5645); >>> if (ret < 0) >>> goto exit; >>> >>> + ret = ov5645_write_reg_to(ov5645, 0x3100, >>> + ov5645->i2c_client->addr, 0x78); >>> + if (ret < 0) { >>> + dev_err(ov5645->dev, >>> + "could not change i2c address\n"); >>> + ov5645_set_power_off(ov5645); >>> + mutex_unlock(&ov5645_lock); >>> + goto exit; >>> + } >>> + >>> + mutex_unlock(&ov5645_lock); >>> + >>> ret = ov5645_set_register_array(ov5645, >>> ov5645_global_init_setting, >>> ARRAY_SIZE(ov5645_global_init_setting)); > ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] [media] ov5645: I2C address change 2017-10-09 8:36 ` Todor Tomov @ 2017-10-09 9:34 ` Sakari Ailus 2017-10-09 12:52 ` Laurent Pinchart 0 siblings, 1 reply; 6+ messages in thread From: Sakari Ailus @ 2017-10-09 9:34 UTC (permalink / raw) To: Todor Tomov Cc: Laurent Pinchart, mchehab, hansverk, linux-media, linux-kernel, linux-i2c, Wolfram Sang Hi Todor, On Mon, Oct 09, 2017 at 11:36:01AM +0300, Todor Tomov wrote: > Hi Sakari, > > On 4.10.2017 13:47, Laurent Pinchart wrote: > > CC'ing the I2C mainling list and the I2C maintainer. > > > > On Wednesday, 4 October 2017 13:30:08 EEST Sakari Ailus wrote: > >> Hi Todor, > >> > >> On Mon, Oct 02, 2017 at 04:28:45PM +0300, Todor Tomov wrote: > >>> As soon as the sensor is powered on, change the I2C address to the one > >>> specified in DT. This allows to use multiple physical sensors connected > >>> to the same I2C bus. > >>> > >>> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > >> > >> The smiapp driver does something similar and I understand Laurent might be > >> interested in such functionality as well. > >> > >> It'd be nice to handle this through the I²C framework instead and to define > >> how the information is specified through DT. That way it could be made > >> generic, to work with more devices than just this one. > >> > >> What do you think? > > Thank you for this suggestion. > > The way I have done it is to put the new I2C address in the DT and the driver > programs the change using the original I2C address. The original I2C address > is hardcoded in the driver. So maybe we can extend the DT binding and the I2C > framework so that both addresses come from the DT and avoid hiding the > original I2C address in the driver. This sounds good to me. Agreed. In this case the address is known but in general that's not the case it's not that simple. There are register compatible devices that have different addresses even if they're the same devices. It might be a good idea to make this explicit. > > Then changing the address could be device specific and also this must be done > right after power on so that there are no address conflicts. So I don't think > that we can support this through the I2C framework only, the drivers that we > want to do that will have to be expanded with this functionality. Or do you > have any other idea? Yes, how the address is changed is always hardware specific. This would be most conveniently done in driver's probe or PM runtime_resume functions. It could be as simple as providing an adapter specific mutex to serialise address changes on the bus so that no two address changes are taking place at the same time. Which is essentially the impliementation you had, only the mutex would be for the I²C adapter, not the driver. An helper functions for acquiring and releasing the mutex. I wonder what others think. -- Regards, Sakari Ailus e-mail: sakari.ailus@iki.fi ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] [media] ov5645: I2C address change 2017-10-09 9:34 ` Sakari Ailus @ 2017-10-09 12:52 ` Laurent Pinchart 2017-10-09 16:18 ` Todor Tomov 0 siblings, 1 reply; 6+ messages in thread From: Laurent Pinchart @ 2017-10-09 12:52 UTC (permalink / raw) To: Sakari Ailus Cc: Todor Tomov, mchehab, hansverk, linux-media, linux-kernel, linux-i2c, Wolfram Sang Hello, On Monday, 9 October 2017 12:34:26 EEST Sakari Ailus wrote: > On Mon, Oct 09, 2017 at 11:36:01AM +0300, Todor Tomov wrote: > > On 4.10.2017 13:47, Laurent Pinchart wrote: > >> CC'ing the I2C mainling list and the I2C maintainer. > >> > >> On Wednesday, 4 October 2017 13:30:08 EEST Sakari Ailus wrote: > >>> On Mon, Oct 02, 2017 at 04:28:45PM +0300, Todor Tomov wrote: > >>>> As soon as the sensor is powered on, change the I2C address to the one > >>>> specified in DT. This allows to use multiple physical sensors > >>>> connected to the same I2C bus. > >>>> > >>>> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > >>> > >>> The smiapp driver does something similar and I understand Laurent might > >>> be interested in such functionality as well. > >>> > >>> It'd be nice to handle this through the I²C framework instead and to > >>> define how the information is specified through DT. That way it could > >>> be made generic, to work with more devices than just this one. > >>> > >>> What do you think? > > > > Thank you for this suggestion. > > > > The way I have done it is to put the new I2C address in the DT and the > > driver programs the change using the original I2C address. The original > > I2C address is hardcoded in the driver. So maybe we can extend the DT > > binding and the I2C framework so that both addresses come from the DT and > > avoid hiding the original I2C address in the driver. This sounds good to > > me. > > Agreed. > > In this case the address is known but in general that's not the case it's > not that simple. There are register compatible devices that have different > addresses even if they're the same devices. > > It might be a good idea to make this explicit. Yes, in the general case we need to specify the original address in DT, as the chip could have a non-fixed boot-up I2C address. In many cases the value of the new I2C address doesn't matter much, as long as it's unique on the bus. I was thinking about implementing a dynamic allocator for I2C addresses, but after discussing it with Wolfram we concluded that it would probably not be a good idea. There could be other I2C devices on the bus that Linux isn't aware of, in which case the dynamic allocator could create address conflicts. Specifying the new address in DT is likely a better idea, even if it could feel a bit more of system configuration information than a pure hardware description. > > Then changing the address could be device specific and also this must be > > done right after power on so that there are no address conflicts. So I > > don't think that we can support this through the I2C framework only, the > > drivers that we want to do that will have to be expanded with this > > functionality. Or do you have any other idea? > > Yes, how the address is changed is always hardware specific. This would be > most conveniently done in driver's probe or PM runtime_resume functions. This patch modifies client->addr directly, which I don't think is a good idea. I'd prefer making the I2C core aware of the address change through an explicit API call. This would allow catching I2C adress conflicts for instance. > It could be as simple as providing an adapter specific mutex to serialise > address changes on the bus so that no two address changes are taking place > at the same time. Which is essentially the impliementation you had, only > the mutex would be for the I²C adapter, not the driver. An helper functions > for acquiring and releasing the mutex. Why do you need to serialize address changes ? > I wonder what others think. -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] [media] ov5645: I2C address change 2017-10-09 12:52 ` Laurent Pinchart @ 2017-10-09 16:18 ` Todor Tomov 2017-10-09 19:13 ` Laurent Pinchart 0 siblings, 1 reply; 6+ messages in thread From: Todor Tomov @ 2017-10-09 16:18 UTC (permalink / raw) To: Laurent Pinchart, Sakari Ailus Cc: mchehab, hansverk, linux-media, linux-kernel, linux-i2c, Wolfram Sang Hi Laurent :) On 9.10.2017 15:52, Laurent Pinchart wrote: > Hello, > > On Monday, 9 October 2017 12:34:26 EEST Sakari Ailus wrote: >> On Mon, Oct 09, 2017 at 11:36:01AM +0300, Todor Tomov wrote: >>> On 4.10.2017 13:47, Laurent Pinchart wrote: >>>> CC'ing the I2C mainling list and the I2C maintainer. >>>> >>>> On Wednesday, 4 October 2017 13:30:08 EEST Sakari Ailus wrote: >>>>> On Mon, Oct 02, 2017 at 04:28:45PM +0300, Todor Tomov wrote: >>>>>> As soon as the sensor is powered on, change the I2C address to the one >>>>>> specified in DT. This allows to use multiple physical sensors >>>>>> connected to the same I2C bus. >>>>>> >>>>>> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> >>>>> >>>>> The smiapp driver does something similar and I understand Laurent might >>>>> be interested in such functionality as well. >>>>> >>>>> It'd be nice to handle this through the I²C framework instead and to >>>>> define how the information is specified through DT. That way it could >>>>> be made generic, to work with more devices than just this one. >>>>> >>>>> What do you think? >>> >>> Thank you for this suggestion. >>> >>> The way I have done it is to put the new I2C address in the DT and the >>> driver programs the change using the original I2C address. The original >>> I2C address is hardcoded in the driver. So maybe we can extend the DT >>> binding and the I2C framework so that both addresses come from the DT and >>> avoid hiding the original I2C address in the driver. This sounds good to >>> me. >> >> Agreed. >> >> In this case the address is known but in general that's not the case it's >> not that simple. There are register compatible devices that have different >> addresses even if they're the same devices. >> >> It might be a good idea to make this explicit. > > Yes, in the general case we need to specify the original address in DT, as the > chip could have a non-fixed boot-up I2C address. > > In many cases the value of the new I2C address doesn't matter much, as long as > it's unique on the bus. I was thinking about implementing a dynamic allocator > for I2C addresses, but after discussing it with Wolfram we concluded that it > would probably not be a good idea. There could be other I2C devices on the bus > that Linux isn't aware of, in which case the dynamic allocator could create > address conflicts. Specifying the new address in DT is likely a better idea, > even if it could feel a bit more of system configuration information than a > pure hardware description. > >>> Then changing the address could be device specific and also this must be >>> done right after power on so that there are no address conflicts. So I >>> don't think that we can support this through the I2C framework only, the >>> drivers that we want to do that will have to be expanded with this >>> functionality. Or do you have any other idea? >> >> Yes, how the address is changed is always hardware specific. This would be >> most conveniently done in driver's probe or PM runtime_resume functions. > > This patch modifies client->addr directly, which I don't think is a good idea. > I'd prefer making the I2C core aware of the address change through an explicit > API call. This would allow catching I2C adress conflicts for instance. > >> It could be as simple as providing an adapter specific mutex to serialise >> address changes on the bus so that no two address changes are taking place >> at the same time. Which is essentially the impliementation you had, only >> the mutex would be for the I²C adapter, not the driver. An helper functions >> for acquiring and releasing the mutex. > > Why do you need to serialize address changes ? Correct me if I'm wrong, but if you power on more than one device with the same I2C address and issue a command to change it, then all devices will recognize this command as addressed to them. The only solution (which I know about) to avoid this is to serialize the power on and address change (as a whole!) for these devices. I think it would be better to move the mutex out of the driver - to avoid all client drivers which will change I2C address to add a global variable mutex for this. We just have to find a better place for it :) > >> I wonder what others think. > -- Best regards, Todor Tomov ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] [media] ov5645: I2C address change 2017-10-09 16:18 ` Todor Tomov @ 2017-10-09 19:13 ` Laurent Pinchart 0 siblings, 0 replies; 6+ messages in thread From: Laurent Pinchart @ 2017-10-09 19:13 UTC (permalink / raw) To: Todor Tomov Cc: Sakari Ailus, mchehab, hansverk, linux-media, linux-kernel, linux-i2c, Wolfram Sang Hi Todor, On Monday, 9 October 2017 19:18:17 EEST Todor Tomov wrote: > On 9.10.2017 15:52, Laurent Pinchart wrote: > > On Monday, 9 October 2017 12:34:26 EEST Sakari Ailus wrote: > >> On Mon, Oct 09, 2017 at 11:36:01AM +0300, Todor Tomov wrote: > >>> On 4.10.2017 13:47, Laurent Pinchart wrote: > >>>> CC'ing the I2C mainling list and the I2C maintainer. > >>>> > >>>> On Wednesday, 4 October 2017 13:30:08 EEST Sakari Ailus wrote: > >>>>> On Mon, Oct 02, 2017 at 04:28:45PM +0300, Todor Tomov wrote: > >>>>>> As soon as the sensor is powered on, change the I2C address to the > >>>>>> one specified in DT. This allows to use multiple physical sensors > >>>>>> connected to the same I2C bus. > >>>>>> > >>>>>> Signed-off-by: Todor Tomov <todor.tomov@linaro.org> > >>>>> > >>>>> The smiapp driver does something similar and I understand Laurent > >>>>> might be interested in such functionality as well. > >>>>> > >>>>> It'd be nice to handle this through the I²C framework instead and to > >>>>> define how the information is specified through DT. That way it could > >>>>> be made generic, to work with more devices than just this one. > >>>>> > >>>>> What do you think? > >>> > >>> Thank you for this suggestion. > >>> > >>> The way I have done it is to put the new I2C address in the DT and the > >>> driver programs the change using the original I2C address. The original > >>> I2C address is hardcoded in the driver. So maybe we can extend the DT > >>> binding and the I2C framework so that both addresses come from the DT > >>> and avoid hiding the original I2C address in the driver. This sounds > >>> good to me. > >> > >> Agreed. > >> > >> In this case the address is known but in general that's not the case it's > >> not that simple. There are register compatible devices that have > >> different addresses even if they're the same devices. > >> > >> It might be a good idea to make this explicit. > > > > Yes, in the general case we need to specify the original address in DT, as > > the chip could have a non-fixed boot-up I2C address. > > > > In many cases the value of the new I2C address doesn't matter much, as > > long as it's unique on the bus. I was thinking about implementing a > > dynamic allocator for I2C addresses, but after discussing it with Wolfram > > we concluded that it would probably not be a good idea. There could be > > other I2C devices on the bus that Linux isn't aware of, in which case the > > dynamic allocator could create address conflicts. Specifying the new > > address in DT is likely a better idea, even if it could feel a bit more > > of system configuration information than a pure hardware description. > > > >>> Then changing the address could be device specific and also this must be > >>> done right after power on so that there are no address conflicts. So I > >>> don't think that we can support this through the I2C framework only, the > >>> drivers that we want to do that will have to be expanded with this > >>> functionality. Or do you have any other idea? > >> > >> Yes, how the address is changed is always hardware specific. This would > >> be most conveniently done in driver's probe or PM runtime_resume > >> functions. > > > > This patch modifies client->addr directly, which I don't think is a good > > idea. I'd prefer making the I2C core aware of the address change through > > an explicit API call. This would allow catching I2C adress conflicts for > > instance. > > > >> It could be as simple as providing an adapter specific mutex to serialise > >> address changes on the bus so that no two address changes are taking > >> place at the same time. Which is essentially the impliementation you had, > >> only the mutex would be for the I²C adapter, not the driver. An helper > >> functions for acquiring and releasing the mutex. > > > > Why do you need to serialize address changes ? > > Correct me if I'm wrong, but if you power on more than one device with the > same I2C address and issue a command to change it, then all devices will > recognize this command as addressed to them. The only solution (which I know > about) to avoid this is to serialize the power on and address change (as a > whole!) for these devices. Yes, that's correct. It can be even worse than that, sometimes only one of the two devices with the same address can be reconfigured, which means that powering that device requires powering up the other device and changing its address first, otherwise the second device can't be used as long as the first one is power on (this happened for real in a Nokia platform). > I think it would be better to move the mutex out of the driver - to avoid > all client drivers which will change I2C address to add a global variable > mutex for this. We just have to find a better place for it :) The biggest issue I see is that there's no C code that has knowledge of the whole platform. It's hard to describe this in DT in a generic way, board files were clearly useful for this kind of situations. > >> I wonder what others think. -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2017-10-09 19:13 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1506950925-13924-1-git-send-email-todor.tomov@linaro.org>
[not found] ` <20171004103008.g7azpn4a3hfj4fs2@valkosipuli.retiisi.org.uk>
2017-10-04 10:47 ` [PATCH] [media] ov5645: I2C address change Laurent Pinchart
2017-10-09 8:36 ` Todor Tomov
2017-10-09 9:34 ` Sakari Ailus
2017-10-09 12:52 ` Laurent Pinchart
2017-10-09 16:18 ` Todor Tomov
2017-10-09 19:13 ` Laurent Pinchart
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).