Re: [PATCH v2 Resent 6/6] i3c: master: svc: fix random hot join failure since timeout errory

Frank Li
2023-10-20T15:48:10Z

On Fri, Oct 20, 2023 at 05:20:06PM +0200, Miquel Raynal wrote:
> Hi Frank,
>
> Frank.li@nxp.com wrote on Fri, 20 Oct 2023 10:47:52 -0400:
>
> > On Fri, Oct 20, 2023 at 04:35:25PM +0200, Miquel Raynal wrote:
> > > Hi Frank,
> > >
> > > Frank.li@nxp.com wrote on Fri, 20 Oct 2023 10:18:55 -0400:
> > >
> > > > On Fri, Oct 20, 2023 at 04:06:45PM +0200, Miquel Raynal wrote:
> > > > > Hi Frank,
> > > > >
> > > > > Frank.li@nxp.com wrote on Thu, 19 Oct 2023 11:39:42 -0400:
> > > > >
> > > > > > On Thu, Oct 19, 2023 at 08:44:52AM +0200, Miquel Raynal wrote:
> > > > > > > Hi Frank,
> > > > > > >
> > > > > > > Frank.Li@nxp.com wrote on Wed, 18 Oct 2023 11:59:26 -0400:
> > > > > > >
> > > > > > > > master side report:
> > > > > > > > silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
> > > > > > > >
> > > > > > > > BIT 20: TIMEOUT error
> > > > > > > > The module has stalled too long in a frame. This happens when:
> > > > > > > > - The TX FIFO or RX FIFO is not handled and the bus is stuck in the
> > > > > > > > middle of a message,
> > > > > > > > - No STOP was issued and between messages,
> > > > > > > > - IBI manual is used and no decision was made.
> > > > > > >
> > > > > > > I am still not convinced this should be ignored in all cases.
> > > > > > >
> > > > > > > Case 1 is a problem because the hardware failed somehow.
> > > > > >
> > > > > > But so far, no action to handle this case in current code.
> > > > >
> > > > > Yes, but if you detect an issue and ignore it, it's not better than
> > > > > reporting it without handling it. Instead of totally ignoring this I
> > > > > would at least write a debug message (identical to what's below) before
> > > > > returning false, even though I am not convinced unconditionally
> > > > > returning false here is wise. If you fail a hardware sequence because
> > > > > you added a printk, it's a problem. Maybe you consider this line as
> > > > > noise, but I believe it's still an error condition. Maybe, however,
> > > > > this bit gets set after the whole sequence, and this is just a "bus
> > > > > is idle" condition. If that's the case, then you need some
> > > > > additional heuristics to properly ignore the bit?
> > > > >
> > > >
> > > > dev_err(master->dev,
> > > > "Error condition: MSTATUS 0x%08x, MERRWARN 0x%08x\n",
> > > > mstatus, merrwarn);
> > > > +
> > > > + /* ignore timeout error */
> > > > + if (merrwarn & SVC_I3C_MERRWARN_TIMEOUT)
> > > > + return false;
> > > > +
> > > >
> > > > Is it okay move SVC_I3C_MERRWARN_TIMEOUT after dev_err?
> > >
> > > I think you mentioned earlier that the problem was not the printk but
> > > the return value. So perhaps there is a way to know if the timeout
> > > happened after a transaction and was legitimate or not?
> >
> > Error message just annoise user, don't impact function. But return false
> > let IBI thread running to avoid dead lock.
> >
> > >
> > > In any case we should probably lower the log level for this error.
> >
> > Only SVC_I3C_MERRWARN_TIMEOUT is warning
> >
> > Maybe below logic is better
> >
> > if (merrwarn & SVC_I3C_MERRWARN_TIMEOUT) {
> > dev_dbg(master->dev,
> > "Error condition: MSTATUS 0x%08x, MERRWARN 0x%08x\n",
> > mstatus, merrwarn);
> > return false;
> > }
> >
> > dev_err(master->dev,
> > "Error condition: MSTATUS 0x%08x, MERRWARN 0x%08x\n",
> > mstatus, merrwarn);
> > ....
> >
>
> Yes, this looks better but I wonder if we should add an additional
> condition to just return false in this case;

What's additional condition we can check?

> something saying "this
> timeout is legitimate and has no impact".

Add comments "this timeout is legitimate and has no impact" or dev_dbg
print that?

>
> Thanks,
> Miquèl