From: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
To: Jarkko Nikula <jarkko.nikula@linux.intel.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>,
Krishnamoorthi M <krishnamoorthi.m@amd.com>,
linux-i3c@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH RESEND v3 2/6] i3c: mipi-i3c-hci: Read HC_CONTROL_PIO_MODE only after i3c hci v1.1
Date: Fri, 9 Aug 2024 21:16:05 +0530 [thread overview]
Message-ID: <62efb2bc-152e-4970-88b9-4d40865bc457@amd.com> (raw)
In-Reply-To: <ce725e2b-378c-46ba-86ad-a877de0e1ef4@linux.intel.com>
On 8/9/2024 18:51, Jarkko Nikula wrote:
> Hi
>
> On 8/7/24 8:23 AM, Shyam Sundar S K wrote:
>> The HC_CONTROL_PIO_MODE bit was introduced in the HC_CONTROL register
>> starting from version 1.1. Therefore, checking the
>> HC_CONTROL_PIO_MODE bit
>> on hardware that adheres to older specification revisions (i.e.,
>> versions
>> earlier than 1.1) is incorrect. To address this, add an additional
>> check
>> to read the HCI version before attempting to read the
>> HC_CONTROL_PIO_MODE
>> status.
>>
>> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
>> ---
>> drivers/i3c/master/mipi-i3c-hci/core.c | 5 +++--
>> 1 file changed, 3 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/i3c/master/mipi-i3c-hci/core.c
>> b/drivers/i3c/master/mipi-i3c-hci/core.c
>> index 24dd4603d6c6..a16da70bdfe1 100644
>> --- a/drivers/i3c/master/mipi-i3c-hci/core.c
>> +++ b/drivers/i3c/master/mipi-i3c-hci/core.c
>> @@ -33,6 +33,7 @@
>> #define reg_clear(r, v) reg_write(r, reg_read(r) & ~(v))
>> #define HCI_VERSION 0x00 /* HCI Version (in BCD) */
>> +#define HCI_VERSION_V1 0x100 /* MIPI HCI Version
>> number V1.0 */
>> #define HC_CONTROL 0x04
>> #define HC_CONTROL_BUS_ENABLE BIT(31)
>> @@ -756,7 +757,7 @@ static int i3c_hci_init(struct i3c_hci *hci)
>> /* Try activating DMA operations first */
>> if (hci->RHS_regs) {
>> reg_clear(HC_CONTROL, HC_CONTROL_PIO_MODE);
>> - if (reg_read(HC_CONTROL) & HC_CONTROL_PIO_MODE) {
>> + if (regval > HCI_VERSION_V1 && !(reg_read(HC_CONTROL) &
>> HC_CONTROL_PIO_MODE)) {
>> dev_err(&hci->master.dev, "PIO mode is stuck\n");
>> ret = -EIO;
>> } else {
>
> Here's typo and logic is reversed.
ah! good catch! thanks, will change this in the next version.
Thanks,
Shyam
--
linux-i3c mailing list
linux-i3c@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-i3c
next prev parent reply other threads:[~2024-08-09 15:46 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-07 5:23 [PATCH RESEND v3 0/6] Introduce initial AMD I3C HCI driver support Shyam Sundar S K
2024-08-07 5:23 ` [PATCH RESEND v3 1/6] i3c: mipi-i3c-hci: Add MIPI0100 ACPI ID to the I3C Support List Shyam Sundar S K
2024-08-09 13:54 ` Jarkko Nikula
2024-08-09 14:18 ` Andy Shevchenko
2024-08-09 15:32 ` Shyam Sundar S K
2024-08-09 15:57 ` Andy Shevchenko
2024-08-09 16:24 ` Shyam Sundar S K
2024-08-09 18:39 ` Alexandre Belloni
2024-08-12 12:17 ` Andy Shevchenko
2024-08-07 5:23 ` [PATCH RESEND v3 2/6] i3c: mipi-i3c-hci: Read HC_CONTROL_PIO_MODE only after i3c hci v1.1 Shyam Sundar S K
2024-08-09 13:21 ` Jarkko Nikula
2024-08-09 15:46 ` Shyam Sundar S K [this message]
2024-08-07 5:23 ` [PATCH RESEND v3 3/6] i3c: mipi-i3c-hci: Add a quirk to set PIO mode Shyam Sundar S K
2024-08-09 13:55 ` Jarkko Nikula
2024-08-09 15:44 ` Shyam Sundar S K
2024-08-12 9:17 ` Jarkko Nikula
2024-08-12 9:32 ` Shyam Sundar S K
2024-08-19 6:41 ` Shyam Sundar S K
2024-08-19 11:10 ` Jarkko Nikula
2024-08-19 16:35 ` Shyam Sundar S K
2024-08-07 5:23 ` [PATCH RESEND v3 4/6] i3c: mipi-i3c-hci: Relocate helper macros to HCI header file Shyam Sundar S K
2024-08-09 13:21 ` Jarkko Nikula
2024-08-07 5:23 ` [PATCH RESEND v3 5/6] i3c: mipi-i3c-hci: Add a quirk to set timing parameters Shyam Sundar S K
2024-08-07 5:23 ` [PATCH RESEND v3 6/6] i3c: mipi-i3c-hci: Add a quirk to set Response buffer threshold Shyam Sundar S K
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=62efb2bc-152e-4970-88b9-4d40865bc457@amd.com \
--to=shyam-sundar.s-k@amd.com \
--cc=Guruvendra.Punugupati@amd.com \
--cc=alexandre.belloni@bootlin.com \
--cc=jarkko.nikula@linux.intel.com \
--cc=krishnamoorthi.m@amd.com \
--cc=linux-i3c@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox