* Still no DMA on boot on S-ATA (Asus A7N8X-deluxe)
@ 2003-05-25 20:06 Gutko
0 siblings, 0 replies; 4+ messages in thread
From: Gutko @ 2003-05-25 20:06 UTC (permalink / raw)
To: linux-ide; +Cc: linux-kernel
Hardware:
Asus A7N8X -deluxe v1.04 bios 1004
SI3112A sata chipset
IBM vancouver2 180GXP pata drive connected to sata trough Asus sata<->pata
converter
Kernel 2.4.21-rc3 (and all older 2.4.x with sata support)
Why my hdd is always detected as PIO?
I can enable udma5 using hdparm, later in rc.local but why it is not working
on boot?
----------DMESG-----------
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
AMD_IDE: PCI device 10de:0065 (nVidia Corporation) (rev a2) UDMA100
controller on pci00:09.0
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
SiI3112 Serial ATA: IDE controller at PCI slot 01:0b.0
SiI3112 Serial ATA: chipset revision 1
SiI3112 Serial ATA: not 100% native mode: will probe irqs later
ide2: MMIO-DMA at 0xe0f54000-0xe0f54007, BIOS settings: hde:pio, hdf:pio
ide3: MMIO-DMA at 0xe0f54008-0xe0f5400f, BIOS settings: hdg:pio, hdh:pio
hdc: LITE-ON LTR-48125S, ATAPI CD/DVD-ROM drive
hdd: HL-DT-STDVD-ROM GDR8160B, ATAPI CD/DVD-ROM drive
hde: IC35L180AVV207-1, ATA DISK drive
hdg: no response (status = 0xfe)
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xe0f54080-0xe0f54087,0xe0f5408a on irq 11
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 361882080 sectors (185284 MB) w/7965KiB Cache, CHS=22526/255/63
------------
hdparm -i /dev/hde
dma enabled manually
Model=IC35L180AVV207-1, FwRev=V26OA60F, SerialNo=VNVF01G6G0VZ9D
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=7965kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a: 2 3 4 5 6
^ permalink raw reply [flat|nested] 4+ messages in thread
* Still no DMA on boot on S-ATA (Asus A7N8X-deluxe)
@ 2003-05-25 20:10 Gutko
0 siblings, 0 replies; 4+ messages in thread
From: Gutko @ 2003-05-25 20:10 UTC (permalink / raw)
To: linux-ide
Hardware:
Asus A7N8X -deluxe v1.04 bios 1004
SI3112A sata chipset
IBM vancouver2 180GXP pata drive connected to sata trough Asus sata<->pata
converter
Kernel 2.4.21-rc3 (and all older 2.4.x with sata support)
Why my hdd is always detected as PIO?
I can enable udma5 using hdparm, later in rc.local but why it is not working
on boot?
----------DMESG-----------
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
AMD_IDE: PCI device 10de:0065 (nVidia Corporation) (rev a2) UDMA100
controller on pci00:09.0
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
SiI3112 Serial ATA: IDE controller at PCI slot 01:0b.0
SiI3112 Serial ATA: chipset revision 1
SiI3112 Serial ATA: not 100% native mode: will probe irqs later
ide2: MMIO-DMA at 0xe0f54000-0xe0f54007, BIOS settings: hde:pio, hdf:pio
ide3: MMIO-DMA at 0xe0f54008-0xe0f5400f, BIOS settings: hdg:pio, hdh:pio
hdc: LITE-ON LTR-48125S, ATAPI CD/DVD-ROM drive
hdd: HL-DT-STDVD-ROM GDR8160B, ATAPI CD/DVD-ROM drive
hde: IC35L180AVV207-1, ATA DISK drive
hdg: no response (status = 0xfe)
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xe0f54080-0xe0f54087,0xe0f5408a on irq 11
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 361882080 sectors (185284 MB) w/7965KiB Cache, CHS=22526/255/63
------------
hdparm -i /dev/hde
dma enabled manually
Model=IC35L180AVV207-1, FwRev=V26OA60F, SerialNo=VNVF01G6G0VZ9D
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=7965kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a: 2 3 4 5 6
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Still no DMA on boot on S-ATA (Asus A7N8X-deluxe)
[not found] <Pine.LNX.4.44.0305251900170.1211-100000@coffee.psychology.mcmaster.ca>
@ 2003-05-26 12:22 ` Gutko
[not found] ` <3ED21294.30701@hifo.unizh.ch>
0 siblings, 1 reply; 4+ messages in thread
From: Gutko @ 2003-05-26 12:22 UTC (permalink / raw)
To: linux-ide; +Cc: linux-kernel
----- Original Message -----
From: "Mark Hahn" <hahn@physics.mcmaster.ca>
To: "Gutko" <gutko@poczta.onet.pl>
Sent: Monday, May 26, 2003 1:02 AM
Subject: Re: Still no DMA on boot on S-ATA (Asus A7N8X-deluxe)
> > Why my hdd is always detected as PIO?
>
> I looked briefly at the driver a couple weeks ago -
> it appears to be deliberate, perhaps an attempt at conservativism.
>
> > I can enable udma5 using hdparm, later in rc.local but why it is not
working
> > on boot?
>
> does it work well? I'm trying to evaluate a system with a SiI3112
> card and two seagate native-sata 120's. things work OK under very
> light use, but quickly degenerate into the classic 'lost interrupt'...
>
yes i works good but i have onboard SIL3112A chipset. Im using it on udma5
about
3 months without any data corruption or errors (linux and windows).
but I have only one drive connected to sata. I've heard people running raid
had
problems undrer windows too
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Still no DMA on boot on S-ATA (Asus A7N8X-deluxe)
[not found] ` <3ED21294.30701@hifo.unizh.ch>
@ 2003-05-26 14:03 ` Gutko
0 siblings, 0 replies; 4+ messages in thread
From: Gutko @ 2003-05-26 14:03 UTC (permalink / raw)
To: linux-ide; +Cc: linux-kernel
> >>>I can enable udma5 using hdparm, later in rc.local but why it is not
> >
> how do you do this?
hdparm -d1 -X udma5 -c1 -m16 /dev/hde
> what kind of Problems?
data corruption
http://www.nforcershq.com/forum/viewtopic.php?t=5108&highlight=data+corruption
>
> I've noticed that with the 2.4.21-rc2 it wasn't possible to use
> framebuffer AND the SiI3112 at the same time. I had to disable fb
> because of this (no loss for me, the debian installer works without fb
> too .-))
I dont know how it was in pure rc2. I always patched it with Alan's -ACx
> Is this solved in -rc3?
if you have more than 512MB try passing "mem=512" to lilo. seems to work
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2003-05-26 13:49 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-05-25 20:06 Still no DMA on boot on S-ATA (Asus A7N8X-deluxe) Gutko
-- strict thread matches above, loose matches on Subject: below --
2003-05-25 20:10 Gutko
[not found] <Pine.LNX.4.44.0305251900170.1211-100000@coffee.psychology.mcmaster.ca>
2003-05-26 12:22 ` Gutko
[not found] ` <3ED21294.30701@hifo.unizh.ch>
2003-05-26 14:03 ` Gutko
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).