* 30 second timeout on bootup with Intel ICH7 and AHCI (2.6.21-rc2)
@ 2007-03-06 23:07 Stephen Hemminger
2007-03-07 4:02 ` Paul Rolland
0 siblings, 1 reply; 4+ messages in thread
From: Stephen Hemminger @ 2007-03-06 23:07 UTC (permalink / raw)
To: Jeff Garzik; +Cc: linux-ide
I am seeing a long pause on bootup of this Core2 system if I enable
AHCI in the BIOS. There is only one disc in this system, so when it
tries ata2 it is talking to an empty connector. If I turn off AHCI
then it seems to be okay.
[ 50.354526] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 50.354585] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 50.354696] ata1: SATA max UDMA/133 cmd 0xffffc2000002a900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 50.354807] ata2: SATA max UDMA/133 cmd 0xffffc2000002a980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 50.354916] ata3: SATA max UDMA/133 cmd 0xffffc2000002aa00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 50.355026] ata4: SATA max UDMA/133 cmd 0xffffc2000002aa80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 315
[ 50.355091] scsi0 : ahci
[ 50.814338] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 50.820393] ata1.00: ATA-7: Maxtor 6Y080M0, YAR51HW0, max UDMA/133
[ 50.820441] ata1.00: 156312576 sectors, multi 0: LBA
[ 50.826556] ata1.00: configured for UDMA/133
[ 50.826603] scsi1 : ahci
[ 51.286155] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
<< snooze >>
[ 81.275537] ata2.00: qc timeout (cmd 0xec)
[ 81.275583] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 89.253479] ata2: port is slow to respond, please be patient (Status 0x80)
[ 112.246549] ata2: port failed to respond (30 secs, Status 0x80)
[ 112.246595] ata2: COMRESET failed (device not ready)
[ 112.246641] ata2: hardreset failed, retrying in 5 secs
[ 118.114292] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 118.119891] ata2.00: ATA-6: Config Disk, RGL10364, max UDMA/133
[ 118.119938] ata2.00: 640 sectors, multi 1: LBA
[ 118.125541] ata2.00: configured for UDMA/133
[ 118.125588] scsi2 : ahci
[ 118.429158] ata3: SATA link down (SStatus 0 SControl 300)
[ 118.429208] scsi3 : ahci
[ 118.733040] ata4: SATA link down (SStatus 0 SControl 300)
[ 118.733160] scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y080M0 YAR5 PQ: 0 ANSI: 5
[ 118.733297] SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
[ 118.733351] sda: Write Protect is off
[ 118.733394] sda: Mode Sense: 00 3a 00 00
[ 118.733408] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 118.733503] SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
[ 118.733556] sda: Write Protect is off
[ 118.733599] sda: Mode Sense: 00 3a 00 00
[ 118.733613] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 118.733674] sda: sda1 sda3 sda4
[ 118.743423] sd 0:0:0:0: Attached scsi disk sda
[ 118.743551] scsi 1:0:0:0: Direct-Access ATA Config Disk RGL1 PQ: 0 ANSI: 5
[ 118.743684] SCSI device sdb: 640 512-byte hdwr sectors (0 MB)
[ 118.743736] sdb: Write Protect is off
[ 118.743779] sdb: Mode Sense: 00 3a 00 00
[ 118.743793] SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 118.743878] SCSI device sdb: 640 512-byte hdwr sectors (0 MB)
[ 118.743930] sdb: Write Protect is off
[ 118.743973] sdb: Mode Sense: 00 3a 00 00
[ 118.743987] SCSI device sdb: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 118.744049] sdb: unknown partition table
[ 118.744310] sd 1:0:0:0: Attached scsi disk sdb
[ 118.744433] usbmon: debugfs is not available
00:00.0 Host bridge: Intel Corporation 975X Express Memory Controller Hub (rev c0)
Subsystem: ASUSTeK Computer Inc. Unknown device 8178
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation 975X Express PCI Express Root Port (rev c0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Memory behind bridge: faa00000-feafffff
Prefetchable memory behind bridge: 00000000cff00000-00000000efe00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4059
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 81d8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Prefetchable memory behind bridge: 00000000cfe00000-00000000cfe00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4061
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fa900000-fa9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4069
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fa800000-fa8fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4071
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e480 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e800 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e880 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at ec00 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at febfbc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fa700000-fa7fffff
Prefetchable memory behind bridge: 0000000088000000-0000000088000000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) Serial ATA Storage Controller AHCI (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 2606
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 315
Region 0: I/O ports at e400 [size=8]
Region 1: I/O ports at e080 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d880 [size=16]
Region 5: Memory at febfb800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4089
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 23
Region 4: I/O ports at 0400 [size=32]
01:00.0 Ethernet controller: D-Link System Inc Gigabit Ethernet Adapter (rev 11)
Subsystem: D-Link System Inc DGE-530T Gigabit Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fa7fc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at a800 [size=256]
Expansion ROM at 88000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 313
Region 0: Memory at fa8fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at b800 [size=256]
Expansion ROM at fa8c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Address: 00000000fee00000 Data: 40b1
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 314
Region 0: Memory at fa9fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at c800 [size=256]
Expansion ROM at fa9c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Address: 00000000fee00000 Data: 40a9
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
05:00.0 VGA compatible controller: nVidia Corporation Unknown device 016a (rev a1) (prog-if 00 [VGA])
Subsystem: eVga.com. Corp. Unknown device c411
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at feae0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
--
Stephen Hemminger <shemminger@linux-foundation.org>
^ permalink raw reply [flat|nested] 4+ messages in thread
* RE: 30 second timeout on bootup with Intel ICH7 and AHCI (2.6.21-rc2)
2007-03-06 23:07 30 second timeout on bootup with Intel ICH7 and AHCI (2.6.21-rc2) Stephen Hemminger
@ 2007-03-07 4:02 ` Paul Rolland
2007-03-07 5:19 ` Stephen Hemminger
0 siblings, 1 reply; 4+ messages in thread
From: Paul Rolland @ 2007-03-07 4:02 UTC (permalink / raw)
To: 'Stephen Hemminger', 'Jeff Garzik'; +Cc: linux-ide
Hello Stephen
> I am seeing a long pause on bootup of this Core2 system if I enable
> AHCI in the BIOS. There is only one disc in this system, so when it
> tries ata2 it is talking to an empty connector. If I turn off AHCI
> then it seems to be okay.
Looks like you have some kind of Asus Mobo... Is that correct ?
It seems that you have the ata2 port that is connected not to a disk,
but to another disk controller.
Robert Ancock wrote me :
"There is something connected, I believe what's actually there on this
board on that port is the SiI4723 chip which is connected to two other
SATA ports. For whatever reason it gets detected as a drive, and it also
seems to be not responding until we do a few resets..
http://www.siliconimage.com/products/product.aspx?id=64"
regarding my P5W DH Deluxe motherboard.
To date, I still don't have any solution for that problem... but it seems
you have some advance as you wrote : "If I turn off AHCI
then it seems to be okay."
I need to test this on my machine too...
Regards,
Paul
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: 30 second timeout on bootup with Intel ICH7 and AHCI (2.6.21-rc2)
2007-03-07 4:02 ` Paul Rolland
@ 2007-03-07 5:19 ` Stephen Hemminger
2007-03-07 16:03 ` 30 second timeout on bootup with Intel ICH7 and AHCI(2.6.21-rc2) Paul Rolland
0 siblings, 1 reply; 4+ messages in thread
From: Stephen Hemminger @ 2007-03-07 5:19 UTC (permalink / raw)
To: rol; +Cc: 'Jeff Garzik', linux-ide
On Wed, 7 Mar 2007 05:02:50 +0100
"Paul Rolland" <rol@as2917.net> wrote:
> Hello Stephen
>
> > I am seeing a long pause on bootup of this Core2 system if I enable
> > AHCI in the BIOS. There is only one disc in this system, so when it
> > tries ata2 it is talking to an empty connector. If I turn off AHCI
> > then it seems to be okay.
>
> Looks like you have some kind of Asus Mobo... Is that correct ?
> It seems that you have the ata2 port that is connected not to a disk,
> but to another disk controller.
>
> Robert Ancock wrote me :
> "There is something connected, I believe what's actually there on this
> board on that port is the SiI4723 chip which is connected to two other
> SATA ports. For whatever reason it gets detected as a drive, and it also
> seems to be not responding until we do a few resets..
>
> http://www.siliconimage.com/products/product.aspx?id=64"
>
> regarding my P5W DH Deluxe motherboard.
> To date, I still don't have any solution for that problem... but it seems
> you have some advance as you wrote : "If I turn off AHCI
> then it seems to be okay."
>
> I need to test this on my machine too...
Could it be the additional RAID controller (not used). I turned it
off in BIOS as well. Maybe if I turned the other ports on, but then
it would have to probe them.
^ permalink raw reply [flat|nested] 4+ messages in thread
* RE: 30 second timeout on bootup with Intel ICH7 and AHCI(2.6.21-rc2)
2007-03-07 5:19 ` Stephen Hemminger
@ 2007-03-07 16:03 ` Paul Rolland
0 siblings, 0 replies; 4+ messages in thread
From: Paul Rolland @ 2007-03-07 16:03 UTC (permalink / raw)
To: 'Stephen Hemminger'; +Cc: 'Jeff Garzik', linux-ide
Hello,
> Could it be the additional RAID controller (not used). I turned it
> off in BIOS as well. Maybe if I turned the other ports on, but then
> it would have to probe them.
Yes, that's it !
I tried to use : ata2=noprobe in the boot parameters, but that seems
to be a no-op... Too bad, 'cos' I know for sure I don't want to connect
something on this raid controller, and that would help me gain at least
30s at boot time...
Or maybe the syntax is wrong ?
Regards,
Paul
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2007-03-07 16:03 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-03-06 23:07 30 second timeout on bootup with Intel ICH7 and AHCI (2.6.21-rc2) Stephen Hemminger
2007-03-07 4:02 ` Paul Rolland
2007-03-07 5:19 ` Stephen Hemminger
2007-03-07 16:03 ` 30 second timeout on bootup with Intel ICH7 and AHCI(2.6.21-rc2) Paul Rolland
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).