From: "Brian & Chamaigne Scamman" <scammanbc@earthlink.net>
To: 'Tejun Heo' <htejun@gmail.com>
Cc: 'Mark Lord' <liml@rtr.ca>, jeff@garzik.org, linux-ide@vger.kernel.org
Subject: RE: [PATCHSET #upstream-fixes] git tree available
Date: Wed, 21 May 2008 15:42:23 -0400 [thread overview]
Message-ID: <00b901c8bb7a$caaa1ed0$6917a8c0@parents> (raw)
In-Reply-To: <4833AC14.5090207@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 776 bytes --]
Tejun Heo wrote:
>Brian & Chamaigne Scamman wrote:
>> One remaining issue is the "failed to IDENTIFY (I/O error, err
mask=0xll)"
>> message. If the PMP, bridges and drives are powered up before I
>> insert the eSATA cable in to the controller, I don't receive the
>> message. The message appears when only when I have the eSATA cable
>> attached to the controller and then simultaneously power on the PMP
>> and drives. In the attached dmesg log, the drive is eventually
>> recognized; however there have been a couple of times when the drives
>> aren't recognized. An eSATA cable remove/re-insert fixes the problem.
>
>Hmm... can you please post the failing log?
Here's a dmesg log where one of the drives is never recognized, but the
others eventually are...
-Brian
[-- Attachment #2: pmp_drive_header_err.txt --]
[-- Type: text/plain, Size: 6104 bytes --]
ata3: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe frozen
ata3: irq_stat 0x00b40090, PHY RDY changed
ata3: hard resetting link
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.15: Port Multiplier 1.1, 0x1095:0x3726 r23, 6 ports, feat 0x1/0x9
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.04: hard resetting link
ata3.04: SATA link down (SStatus 0 SControl 320)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: ATA-6: Super Talent Tech, Rev 2.11, max UDMA/133
ata3.00: 127923200 sectors, multi 1: LBA
ata3.00: applying bridge limits
ata3.00: configured for UDMA/100
ata3.01: ATA-6: Super Talent Tech, Rev 2.11, max UDMA/133
ata3.01: 127923200 sectors, multi 1: LBA
ata3.01: applying bridge limits
ata3.01: configured for UDMA/100
ata3.02: ATA-6: Super Talent Tech, Rev 2.11, max UDMA/133
ata3.02: 127923200 sectors, multi 1: LBA
ata3.02: applying bridge limits
ata3.02: configured for UDMA/100
ata3.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.04: hard resetting link
ata3.04: SATA link down (SStatus 0 SControl 320)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata3.02: configured for UDMA/100
ata3.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.03: hard resetting link
ata3.03: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata3.02: configured for UDMA/100
ata3.03: failed to IDENTIFY (I/O error, err_mask=0x11)
ata3.03: failed to recover link after 3 tries, disabling
ata3: failed to recover PMP, retrying in 5 secs
ata3.15: hard resetting link
ata3.15: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
ata3.00: hard resetting link
ata3.00: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.01: hard resetting link
ata3.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.02: hard resetting link
ata3.02: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.04: hard resetting link
ata3.04: SATA link down (SStatus 0 SControl 320)
ata3.05: hard resetting link
ata3.05: SATA link up 1.5 Gbps (SStatus 113 SControl 320)
ata3.00: configured for UDMA/100
ata3.01: configured for UDMA/100
ata3.02: configured for UDMA/100
ata3: EH complete
scsi 2:0:0:0: Direct-Access ATA Super Talent Tec Rev PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 127923200 512-byte hardware sectors (65497 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 127923200 512-byte hardware sectors (65497 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 2:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg0 type 0
scsi 2:1:0:0: Direct-Access ATA Super Talent Tec Rev PQ: 0 ANSI: 5
sd 2:1:0:0: [sdb] 127923200 512-byte hardware sectors (65497 MB)
sd 2:1:0:0: [sdb] Write Protect is off
sd 2:1:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:1:0:0: [sdb] 127923200 512-byte hardware sectors (65497 MB)
sd 2:1:0:0: [sdb] Write Protect is off
sd 2:1:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:1:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 2:1:0:0: [sdb] Attached SCSI disk
sd 2:1:0:0: Attached scsi generic sg1 type 0
scsi 2:2:0:0: Direct-Access ATA Super Talent Tec Rev PQ: 0 ANSI: 5
sd 2:2:0:0: [sdc] 127923200 512-byte hardware sectors (65497 MB)
sd 2:2:0:0: [sdc] Write Protect is off
sd 2:2:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 2:2:0:0: [sdc] 127923200 512-byte hardware sectors (65497 MB)
sd 2:2:0:0: [sdc] Write Protect is off
sd 2:2:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:2:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:2:0:0: [sdc] Attached SCSI disk
sd 2:2:0:0: Attached scsi generic sg2 type 0
next prev parent reply other threads:[~2008-05-21 19:42 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-05-18 16:15 [PATCHSET #upstream-fixes] libata: fix a bunch of PMP related problems Tejun Heo
2008-05-18 16:15 ` [PATCH 01/10] libata: fix sata_link_hardreset() @online out parameter handling Tejun Heo
2008-05-19 21:53 ` Jeff Garzik
2008-05-18 16:15 ` [PATCH 02/10] libata: reorganize ata_eh_reset() no reset method path Tejun Heo
2008-05-18 16:15 ` [PATCH 03/10] libata: move reset freeze/thaw handling into ata_eh_reset() Tejun Heo
2008-05-18 16:15 ` [PATCH 04/10] libata: kill hotplug related race condition Tejun Heo
2008-05-18 16:15 ` [PATCH 05/10] libata: ignore recovered PHY errors Tejun Heo
2008-05-19 21:50 ` Jeff Garzik
2008-05-18 16:15 ` [PATCH 06/10] libata: increase PMP register access timeout to 3s Tejun Heo
2008-05-18 16:15 ` [PATCH 07/10] libata: make sure PMP notification is turned off during recovery Tejun Heo
2008-05-18 16:15 ` [PATCH 08/10] libata: don't schedule LPM action seperately during probing Tejun Heo
2008-05-18 16:15 ` [PATCH 09/10] sata_sil24: don't use NCQ if marvell 4140 PMP is attached Tejun Heo
2008-05-18 21:14 ` Mark Lord
2008-05-18 16:15 ` [PATCH 10/10] libata: ignore SIMG4726 config pseudo device Tejun Heo
2008-05-18 16:29 ` [PATCHSET #upstream-fixes] git tree available Tejun Heo
2008-05-20 1:35 ` Brian & Chamaigne Scamman
2008-05-20 2:58 ` Mark Lord
2008-05-20 4:28 ` Tejun Heo
2008-05-20 4:43 ` Tejun Heo
2008-05-21 1:32 ` Brian & Chamaigne Scamman
2008-05-21 4:59 ` Tejun Heo
2008-05-21 11:14 ` Brian & Chamaigne Scamman
2008-05-21 19:42 ` Brian & Chamaigne Scamman [this message]
2008-05-22 0:40 ` Tejun Heo
2008-05-23 0:49 ` Brian & Chamaigne Scamman
2008-05-23 1:04 ` Tejun Heo
2008-05-29 3:06 ` Tejun Heo
2008-05-29 3:11 ` Brian & Chamaigne Scamman
2008-05-20 12:08 ` Brian & Chamaigne Scamman
2008-05-20 14:50 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='00b901c8bb7a$caaa1ed0$6917a8c0@parents' \
--to=scammanbc@earthlink.net \
--cc=htejun@gmail.com \
--cc=jeff@garzik.org \
--cc=liml@rtr.ca \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).