From: Soeren Sonnenburg <kernel@nn7.de>
To: Linux Kernel <linux-kernel@vger.kernel.org>,
Linux-ide <linux-ide@vger.kernel.org>
Cc: Tejun Heo <htejun@gmail.com>
Subject: Do ICH10+AHCI-driver support port-multiplying on a eSATA port?
Date: Fri, 09 Jan 2009 16:01:27 +0100 [thread overview]
Message-ID: <1231513287.2631.68.camel@localhost> (raw)
Dear all,
I am trying to connect an external 2-disk case (eCube II see
http://www.one-tech.com/EN/htm_ecube.htm) to an ICH10 skyburg dp45sg
board via eSATA. As the case requires a port-multiplying sata card, I am
wondering if ich10+ahci support it?
At least with 2.6.27.10 I am seeing only one drive. Connecting the case
via usb gives two (dmesg parts below).
So is port multiplying not yet available for ahci or not at all or does
the the ich10 not support it and I should rather try a sil 3132 or so?
Thanks,
Soeren
ata4: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
ata4: irq_stat 0x00000040, connection status changed
ata4: SError: { PHYRdyChg CommWake DevExch }
ata4: hard resetting link
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7: ST3400832AS, 3.01, max UDMA/133
ata4.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
ata4: EH complete
scsi 3:0:0:0: Direct-Access ATA ST3400832AS 3.01 PQ: 0 ANSI: 5
sd 3:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB)
sd 3:0:0:0: [sde] Write Protect is off
sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: unknown partition table
sd 3:0:0:0: [sde] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg5 type 0
ata4: exception Emask 0x50 SAct 0x0 SErr 0x4490801 action 0xe frozen
ata4: irq_stat 0x00400040, connection status changed
ata4: SError: { RecovData HostInt PHYRdyChg 10B8B Handshk DevExch }
ata4: hard resetting link
ata4: SATA link down (SStatus 0 SControl 300)
ata4: hard resetting link
ata4: SATA link down (SStatus 0 SControl 300)
ata4: hard resetting link
ata4: SATA link down (SStatus 0 SControl 300)
ata4.00: disabled
ata4: EH complete
ata4.00: detaching (SCSI 3:0:0:0)
sd 3:0:0:0: [sde] Synchronizing SCSI cache
sd 3:0:0:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
sd 3:0:0:0: [sde] Stopping disk
sd 3:0:0:0: [sde] START_STOP FAILED
sd 3:0:0:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
usb 1-4: new high speed USB device using ehci_hcd and address 6
usb 1-4: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb 1-4: New USB device found, idVendor=1a4a, idProduct=1670
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: 5744 FW:1.1516
usb 1-4: Manufacturer: Silicon Image, Inc
usb 1-4: SerialNumber: 9999999999999999999
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
scsi 7:0:0:0: Direct-Access ST340083 3NF0 PQ: 0 ANSI: 2
sd 7:0:0:0: [sde] 781422769 512-byte hardware sectors (400088 MB)
sd 7:0:0:0: [sde] Write Protect is off
sd 7:0:0:0: [sde] Mode Sense: 1a 0c 00 00
sd 7:0:0:0: [sde] Assuming drive cache: write through
sd 7:0:0:0: [sde] 781422769 512-byte hardware sectors (400088 MB)
sd 7:0:0:0: [sde] Write Protect is off
sd 7:0:0:0: [sde] Mode Sense: 1a 0c 00 00
sd 7:0:0:0: [sde] Assuming drive cache: write through
sde: unknown partition table
sd 7:0:0:0: [sde] Attached SCSI disk
sd 7:0:0:0: Attached scsi generic sg5 type 0
scsi 7:0:0:1: Direct-Access ST340062 5QG0 PQ: 0 ANSI: 2
sd 7:0:0:1: [sdf] 781422769 512-byte hardware sectors (400088 MB)
sd 7:0:0:1: [sdf] Write Protect is off
sd 7:0:0:1: [sdf] Mode Sense: 1a 0c 00 00
sd 7:0:0:1: [sdf] Assuming drive cache: write through
sd 7:0:0:1: [sdf] 781422769 512-byte hardware sectors (400088 MB)
sd 7:0:0:1: [sdf] Write Protect is off
sd 7:0:0:1: [sdf] Mode Sense: 1a 0c 00 00
sd 7:0:0:1: [sdf] Assuming drive cache: write through
sdf: unknown partition table
sd 7:0:0:1: [sdf] Attached SCSI disk
sd 7:0:0:1: Attached scsi generic sg6 type 0
next reply other threads:[~2009-01-09 15:01 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-01-09 15:01 Soeren Sonnenburg [this message]
2009-01-10 0:01 ` Do ICH10+AHCI-driver support port-multiplying on a eSATA port? Robin H. Johnson
2009-01-12 1:44 ` Tejun Heo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1231513287.2631.68.camel@localhost \
--to=kernel@nn7.de \
--cc=htejun@gmail.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).