linux-ide.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Brian Norris <computersforpeace@gmail.com>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org,
	Linux Kernel <linux-kernel@vger.kernel.org>,
	Tejun Heo <tj@kernel.org>,
	Brian Norris <computersforpeace@gmail.com>,
	Lin Ming <ming.m.lin@intel.com>,
	Norbert Preining <preining@logic.at>,
	"Srivatsa S . Bhat" <srivatsa.bhat@linux.vnet.ibm.com>,
	Valdis Kletnieks <valdis.kletnieks@vt.edu>,
	"Rafael J . Wysocki" <rjw@sisk.pl>
Subject: [PATCH v2 1/3] ahci: add AHCI_HFLAG_DELAY_ENGINE host flag
Date: Tue, 21 Feb 2012 10:38:42 -0800	[thread overview]
Message-ID: <1329849524-23758-2-git-send-email-computersforpeace@gmail.com> (raw)
In-Reply-To: <1329849524-23758-1-git-send-email-computersforpeace@gmail.com>

The following commit was intended to fix problems with specific AHCI
controller(s) that would become bricks if the AHCI specification was not
followed strictly (that is, if ahci_start_engine() was called while the
controller was in the wrong state):

    commit 7faa33da9b7add01db9f1ad92c6a5d9145e940a7
    ahci: start engine only during soft/hard resets

However, some devices currently have issues with that fix, so we must
implement a flag that delays the ahci_start_engine() call only for specific
controllers.

This commit simply introduces the flag, without enabling it in any driver.

Note that even when AHCI_HFLAG_DELAY_ENGINE is not enabled, this patch does
not constitue a full revert to commit 7faa33da; there is still a change in
behavior to the ahci_port_suspend() failure path.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
---
 drivers/ata/ahci.h    |    3 +++
 drivers/ata/libahci.c |    5 +++++
 2 files changed, 8 insertions(+), 0 deletions(-)

diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index b175000..feb127e 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -210,6 +210,9 @@ enum {
 	AHCI_HFLAG_NO_SNTF		= (1 << 12), /* no sntf */
 	AHCI_HFLAG_NO_FPDMA_AA		= (1 << 13), /* no FPDMA AA */
 	AHCI_HFLAG_YES_FBS		= (1 << 14), /* force FBS cap on */
+	AHCI_HFLAG_DELAY_ENGINE		= (1 << 15), /* do not start engine on
+						        port start (wait until
+						        error-handling stage) */
 
 	/* ap->flags bits */
 
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index a72bfd0..f9eaa82 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -737,6 +737,7 @@ static void ahci_power_down(struct ata_port *ap)
 
 static void ahci_start_port(struct ata_port *ap)
 {
+	struct ahci_host_priv *hpriv = ap->host->private_data;
 	struct ahci_port_priv *pp = ap->private_data;
 	struct ata_link *link;
 	struct ahci_em_priv *emp;
@@ -746,6 +747,10 @@ static void ahci_start_port(struct ata_port *ap)
 	/* enable FIS reception */
 	ahci_start_fis_rx(ap);
 
+	/* enable DMA */
+	if (!(hpriv->flags & AHCI_HFLAG_DELAY_ENGINE))
+		ahci_start_engine(ap);
+
 	/* turn on LEDs */
 	if (ap->flags & ATA_FLAG_EM) {
 		ata_for_each_link(link, ap, EDGE) {

  reply	other threads:[~2012-02-21 18:38 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-02-21 18:38 [PATCH v2 0/3] ahci: fix boot/resume COMRESET failures Brian Norris
2012-02-21 18:38 ` Brian Norris [this message]
2012-03-13 20:36   ` [PATCH v2 1/3] ahci: add AHCI_HFLAG_DELAY_ENGINE host flag Jeff Garzik
2012-02-21 18:38 ` [PATCH v2 2/3] ahci: move AHCI_HFLAGS() macro to ahci.h Brian Norris
2012-02-21 18:38 ` [PATCH v2 3/3] ahci_platform: add STRICT_AHCI platform type Brian Norris
2012-02-23  0:02 ` [PATCH v2 0/3] ahci: fix boot/resume COMRESET failures Norbert Preining
2012-03-06 18:24   ` Brian Norris
2012-03-02 13:16 ` cwillu
2012-03-05  0:58   ` Lin Ming
2012-03-05  5:12     ` cwillu
2012-03-07  5:28       ` Lin Ming
2012-03-09 16:07         ` cwillu
2012-03-10  0:07         ` Matt
2012-03-12 22:12 ` Tejun Heo
2012-03-13 20:37   ` Jeff Garzik

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1329849524-23758-2-git-send-email-computersforpeace@gmail.com \
    --to=computersforpeace@gmail.com \
    --cc=jgarzik@pobox.com \
    --cc=linux-ide@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=ming.m.lin@intel.com \
    --cc=preining@logic.at \
    --cc=rjw@sisk.pl \
    --cc=srivatsa.bhat@linux.vnet.ibm.com \
    --cc=tj@kernel.org \
    --cc=valdis.kletnieks@vt.edu \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).