* Re: ATA/133 Problems with multiple cards
2004-10-21 21:56 ` James Stevenson
@ 2004-10-22 2:42 ` Albert Lee
2004-10-22 23:51 ` James Stevenson
0 siblings, 1 reply; 17+ messages in thread
From: Albert Lee @ 2004-10-22 2:42 UTC (permalink / raw)
To: James Stevenson; +Cc: Bartlomiej Zolnierkiewicz, hpj, IDE Linux
[-- Attachment #1: Type: text/plain, Size: 2285 bytes --]
Hi, James:
Maybe it is caused by firmware not initializing the registers
of the 3rd adapter correctly. Could you please test the attached
patch with 2.6.9 kernel and collect the "dmesg" output for the registers
values?
Thanks,
Albert
----- Original Message -----
From: "James Stevenson" <james@stev.org>
To: "Hans-Peter Jansen" <hpj@urpla.net>
Cc: "Bartlomiej Zolnierkiewicz" <bzolnier@gmail.com>;
<linux-ide@vger.kernel.org>; <linux-kernel@vger.kernel.org>;
<kernelnewbies@nl.linux.org>
Sent: Friday, October 22, 2004 5:56 AM
Subject: Re: ATA/133 Problems with multiple cards
> On Thu, 21 Oct 2004, Hans-Peter Jansen wrote:
>
> > On Thursday 21 October 2004 20:43, Bartlomiej Zolnierkiewicz wrote:
> > > On Wed, 20 Oct 2004 16:23:21 +0200, Hans-Peter Jansen
> > <hpj@urpla.net> wrote:
> > > > Hmm, I'm running 3 TX2/100 (even with different revisions)
> > > > without big problems here:
> > > >
> > > > 00:09.0 Unknown mass storage controller: Promise Technology, Inc.
> > > > 20268 (rev 02) 00:0a.0 Unknown mass storage controller: Promise
> > > > Technology, Inc. 20268 (rev 02) 00:0b.0 Unknown mass storage
> > > > controller: Promise Technology, Inc. 20268 (rev 01)
> > >
> > > lspci -xxx ?
> >
> > With pleasure. Let me know, if I can provide anything else useful.
> > BTW, Bart, I suspect James' problem is, that his system is running in
> > pic mode, while mine is in apic mode.
>
> i dont actually think that this is a problem i was reading an artical from
> a website (cant find address now) which was stating that the promise
> card's fireware on the PDC20269 was limited by the firmware to 2 cards
> and the 3rd did not work in other cases. The author had setup various
> other systems in the same way using other promise hardware but slightly
> different cards.
>
> I have replaced the 3rd promise card with a highpoint card and everything
> is working fine and has been for the last 36 hours.
>
> James
>
> --
> --------------------------
> Mobile: +44 07779080838
> http://www.stev.org
> 10:50pm up 1 day, 9:16, 3 users, load average: 0.07, 0.02, 0.00
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-ide" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
[-- Attachment #2: patch-pdc-2.6.9 --]
[-- Type: application/octet-stream, Size: 76603 bytes --]
diff -Nru linux-2.6.9-ori/.config linux-2.6.9-mod/.config
--- linux-2.6.9-ori/.config 1970-01-01 08:00:00.000000000 +0800
+++ linux-2.6.9-mod/.config 2004-10-21 14:36:08.000000000 +0800
@@ -0,0 +1,2379 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.9
+# Thu Oct 21 14:06:28 2004
+#
+CONFIG_X86=y
+CONFIG_MMU=y
+CONFIG_UID16=y
+CONFIG_GENERIC_ISA_DMA=y
+CONFIG_GENERIC_IOMAP=y
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_CLEAN_COMPILE=y
+CONFIG_BROKEN_ON_SMP=y
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+CONFIG_SYSCTL=y
+CONFIG_AUDIT=y
+CONFIG_AUDITSYSCALL=y
+CONFIG_LOG_BUF_SHIFT=17
+CONFIG_HOTPLUG=y
+# CONFIG_IKCONFIG is not set
+# CONFIG_EMBEDDED is not set
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+# CONFIG_TINY_SHMEM is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+CONFIG_KMOD=y
+
+#
+# Processor type and features
+#
+CONFIG_X86_PC=y
+# CONFIG_X86_ELAN is not set
+# CONFIG_X86_VOYAGER is not set
+# CONFIG_X86_NUMAQ is not set
+# CONFIG_X86_SUMMIT is not set
+# CONFIG_X86_BIGSMP is not set
+# CONFIG_X86_VISWS is not set
+# CONFIG_X86_GENERICARCH is not set
+# CONFIG_X86_ES7000 is not set
+# CONFIG_M386 is not set
+# CONFIG_M486 is not set
+CONFIG_M586=y
+# CONFIG_M586TSC is not set
+# CONFIG_M586MMX is not set
+# CONFIG_M686 is not set
+# CONFIG_MPENTIUMII is not set
+# CONFIG_MPENTIUMIII is not set
+# CONFIG_MPENTIUMM is not set
+# CONFIG_MPENTIUM4 is not set
+# CONFIG_MK6 is not set
+# CONFIG_MK7 is not set
+# CONFIG_MK8 is not set
+# CONFIG_MCRUSOE is not set
+# CONFIG_MWINCHIPC6 is not set
+# CONFIG_MWINCHIP2 is not set
+# CONFIG_MWINCHIP3D is not set
+# CONFIG_MCYRIXIII is not set
+# CONFIG_MVIAC3_2 is not set
+CONFIG_X86_GENERIC=y
+CONFIG_X86_CMPXCHG=y
+CONFIG_X86_XADD=y
+CONFIG_X86_L1_CACHE_SHIFT=7
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_X86_PPRO_FENCE=y
+CONFIG_X86_F00F_BUG=y
+CONFIG_X86_WP_WORKS_OK=y
+CONFIG_X86_INVLPG=y
+CONFIG_X86_BSWAP=y
+CONFIG_X86_POPAD_OK=y
+CONFIG_X86_ALIGNMENT_16=y
+CONFIG_X86_INTEL_USERCOPY=y
+CONFIG_HPET_TIMER=y
+CONFIG_HPET_EMULATE_RTC=y
+# CONFIG_SMP is not set
+# CONFIG_PREEMPT is not set
+# CONFIG_X86_UP_APIC is not set
+CONFIG_X86_MCE=y
+# CONFIG_X86_MCE_NONFATAL is not set
+CONFIG_TOSHIBA=m
+CONFIG_I8K=m
+# CONFIG_MICROCODE is not set
+CONFIG_X86_MSR=m
+CONFIG_X86_CPUID=m
+
+#
+# Firmware Drivers
+#
+CONFIG_EDD=m
+# CONFIG_NOHIGHMEM is not set
+CONFIG_HIGHMEM4G=y
+# CONFIG_HIGHMEM64G is not set
+CONFIG_HIGHMEM=y
+CONFIG_HIGHPTE=y
+# CONFIG_MATH_EMULATION is not set
+CONFIG_MTRR=y
+# CONFIG_EFI is not set
+CONFIG_REGPARM=y
+
+#
+# Power management options (ACPI, APM)
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+# CONFIG_SOFTWARE_SUSPEND is not set
+
+#
+# ACPI (Advanced Configuration and Power Interface) Support
+#
+CONFIG_ACPI=y
+CONFIG_ACPI_BOOT=y
+CONFIG_ACPI_INTERPRETER=y
+CONFIG_ACPI_SLEEP=y
+CONFIG_ACPI_SLEEP_PROC_FS=y
+CONFIG_ACPI_AC=m
+CONFIG_ACPI_BATTERY=m
+CONFIG_ACPI_BUTTON=m
+CONFIG_ACPI_FAN=y
+CONFIG_ACPI_PROCESSOR=y
+CONFIG_ACPI_THERMAL=y
+CONFIG_ACPI_ASUS=m
+CONFIG_ACPI_TOSHIBA=m
+CONFIG_ACPI_BLACKLIST_YEAR=0
+# CONFIG_ACPI_DEBUG is not set
+CONFIG_ACPI_BUS=y
+CONFIG_ACPI_EC=y
+CONFIG_ACPI_POWER=y
+CONFIG_ACPI_PCI=y
+CONFIG_ACPI_SYSTEM=y
+CONFIG_X86_PM_TIMER=y
+
+#
+# APM (Advanced Power Management) BIOS Support
+#
+CONFIG_APM=y
+# CONFIG_APM_IGNORE_USER_SUSPEND is not set
+# CONFIG_APM_DO_ENABLE is not set
+CONFIG_APM_CPU_IDLE=y
+# CONFIG_APM_DISPLAY_BLANK is not set
+CONFIG_APM_RTC_IS_GMT=y
+# CONFIG_APM_ALLOW_INTS is not set
+# CONFIG_APM_REAL_MODE_POWER_OFF is not set
+
+#
+# CPU Frequency scaling
+#
+CONFIG_CPU_FREQ=y
+# CONFIG_CPU_FREQ_PROC_INTF is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=m
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+# CONFIG_CPU_FREQ_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_24_API is not set
+CONFIG_CPU_FREQ_TABLE=y
+
+#
+# CPUFreq processor drivers
+#
+CONFIG_X86_ACPI_CPUFREQ=m
+# CONFIG_X86_ACPI_CPUFREQ_PROC_INTF is not set
+CONFIG_X86_POWERNOW_K6=m
+CONFIG_X86_POWERNOW_K7=y
+CONFIG_X86_POWERNOW_K7_ACPI=y
+# CONFIG_X86_POWERNOW_K8 is not set
+# CONFIG_X86_GX_SUSPMOD is not set
+CONFIG_X86_SPEEDSTEP_CENTRINO=y
+CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
+CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
+CONFIG_X86_SPEEDSTEP_ICH=y
+CONFIG_X86_SPEEDSTEP_SMI=m
+CONFIG_X86_P4_CLOCKMOD=m
+CONFIG_X86_SPEEDSTEP_LIB=y
+# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set
+CONFIG_X86_LONGRUN=y
+CONFIG_X86_LONGHAUL=y
+
+#
+# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
+#
+CONFIG_PCI=y
+# CONFIG_PCI_GOBIOS is not set
+# CONFIG_PCI_GOMMCONFIG is not set
+# CONFIG_PCI_GODIRECT is not set
+CONFIG_PCI_GOANY=y
+CONFIG_PCI_BIOS=y
+CONFIG_PCI_DIRECT=y
+CONFIG_PCI_MMCONFIG=y
+CONFIG_PCI_LEGACY_PROC=y
+# CONFIG_PCI_NAMES is not set
+CONFIG_ISA=y
+# CONFIG_EISA is not set
+# CONFIG_MCA is not set
+# CONFIG_SCx200 is not set
+
+#
+# PCMCIA/CardBus support
+#
+CONFIG_PCMCIA=m
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_YENTA=m
+CONFIG_CARDBUS=y
+# CONFIG_PD6729 is not set
+CONFIG_I82092=m
+CONFIG_I82365=m
+CONFIG_TCIC=m
+CONFIG_PCMCIA_PROBE=y
+
+#
+# PCI Hotplug Support
+#
+CONFIG_HOTPLUG_PCI=y
+# CONFIG_HOTPLUG_PCI_FAKE is not set
+CONFIG_HOTPLUG_PCI_COMPAQ=m
+# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
+# CONFIG_HOTPLUG_PCI_ACPI is not set
+# CONFIG_HOTPLUG_PCI_CPCI is not set
+CONFIG_HOTPLUG_PCI_PCIE=m
+CONFIG_HOTPLUG_PCI_PCIE_POLL_EVENT_MODE=y
+CONFIG_HOTPLUG_PCI_SHPC=m
+CONFIG_HOTPLUG_PCI_SHPC_POLL_EVENT_MODE=y
+
+#
+# Executable file formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_AOUT is not set
+CONFIG_BINFMT_MISC=m
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+
+#
+# Memory Technology Devices (MTD)
+#
+CONFIG_MTD=m
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_PARTITIONS is not set
+CONFIG_MTD_CONCAT=m
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=m
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_BLOCK_RO=m
+CONFIG_FTL=m
+CONFIG_NFTL=m
+CONFIG_NFTL_RW=y
+CONFIG_INFTL=m
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=m
+CONFIG_MTD_JEDECPROBE=m
+CONFIG_MTD_GEN_PROBE=m
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=m
+CONFIG_MTD_CFI_AMDSTD=m
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
+CONFIG_MTD_CFI_STAA=m
+CONFIG_MTD_CFI_UTIL=m
+CONFIG_MTD_RAM=m
+CONFIG_MTD_ROM=m
+CONFIG_MTD_ABSENT=m
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_SC520CDP=m
+CONFIG_MTD_SCx200_DOCFLASH=m
+CONFIG_MTD_AMD76XROM=m
+# CONFIG_MTD_ICHXROM is not set
+CONFIG_MTD_SCB2_FLASH=m
+CONFIG_MTD_L440GX=m
+CONFIG_MTD_PCI=m
+
+#
+# Self-contained MTD device drivers
+#
+CONFIG_MTD_PMC551=m
+# CONFIG_MTD_PMC551_BUGFIX is not set
+# CONFIG_MTD_PMC551_DEBUG is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+CONFIG_MTD_MTDRAM=m
+CONFIG_MTDRAM_TOTAL_SIZE=4096
+CONFIG_MTDRAM_ERASE_SIZE=128
+# CONFIG_MTD_BLKMTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+CONFIG_MTD_DOC2000=m
+# CONFIG_MTD_DOC2001 is not set
+CONFIG_MTD_DOC2001PLUS=m
+CONFIG_MTD_DOCPROBE=m
+CONFIG_MTD_DOCECC=m
+# CONFIG_MTD_DOCPROBE_ADVANCED is not set
+CONFIG_MTD_DOCPROBE_ADDRESS=0
+
+#
+# NAND Flash Device Drivers
+#
+CONFIG_MTD_NAND=m
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+CONFIG_MTD_NAND_IDS=m
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+
+#
+# Parallel port support
+#
+CONFIG_PARPORT=m
+CONFIG_PARPORT_PC=m
+CONFIG_PARPORT_PC_CML1=m
+CONFIG_PARPORT_SERIAL=m
+# CONFIG_PARPORT_PC_FIFO is not set
+# CONFIG_PARPORT_PC_SUPERIO is not set
+CONFIG_PARPORT_PC_PCMCIA=m
+# CONFIG_PARPORT_OTHER is not set
+CONFIG_PARPORT_1284=y
+
+#
+# Plug and Play support
+#
+CONFIG_PNP=y
+# CONFIG_PNP_DEBUG is not set
+
+#
+# Protocols
+#
+CONFIG_ISAPNP=y
+# CONFIG_PNPBIOS is not set
+
+#
+# Block devices
+#
+CONFIG_BLK_DEV_FD=m
+# CONFIG_BLK_DEV_XD is not set
+# CONFIG_PARIDE is not set
+CONFIG_BLK_CPQ_DA=m
+CONFIG_BLK_CPQ_CISS_DA=m
+CONFIG_CISS_SCSI_TAPE=y
+CONFIG_BLK_DEV_DAC960=m
+CONFIG_BLK_DEV_UMEM=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
+# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_LBD=y
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+CONFIG_SCSI=y
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_CHR_DEV_OSST=m
+CONFIG_BLK_DEV_SR=y
+CONFIG_BLK_DEV_SR_VENDOR=y
+CONFIG_CHR_DEV_SG=m
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+
+#
+# SCSI Transport Attributes
+#
+CONFIG_SCSI_SPI_ATTRS=y
+CONFIG_SCSI_FC_ATTRS=m
+
+#
+# SCSI low-level drivers
+#
+CONFIG_BLK_DEV_3W_XXXX_RAID=m
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_7000FASST is not set
+# CONFIG_SCSI_ACARD is not set
+CONFIG_SCSI_AHA152X=m
+CONFIG_SCSI_AHA1542=m
+CONFIG_SCSI_AACRAID=m
+CONFIG_SCSI_AIC7XXX=m
+CONFIG_AIC7XXX_CMDS_PER_DEVICE=4
+CONFIG_AIC7XXX_RESET_DELAY_MS=15000
+# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
+CONFIG_AIC7XXX_DEBUG_MASK=0
+# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set
+CONFIG_SCSI_AIC7XXX_OLD=m
+CONFIG_SCSI_AIC79XX=m
+CONFIG_AIC79XX_CMDS_PER_DEVICE=4
+CONFIG_AIC79XX_RESET_DELAY_MS=15000
+# CONFIG_AIC79XX_ENABLE_RD_STRM is not set
+# CONFIG_AIC79XX_DEBUG_ENABLE is not set
+CONFIG_AIC79XX_DEBUG_MASK=0
+# CONFIG_AIC79XX_REG_PRETTY_PRINT is not set
+# CONFIG_SCSI_DPT_I2O is not set
+CONFIG_SCSI_IN2000=m
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+CONFIG_SCSI_SATA=y
+CONFIG_SCSI_SATA_SVW=m
+CONFIG_SCSI_ATA_PIIX=m
+# CONFIG_SCSI_SATA_NV is not set
+CONFIG_SCSI_PATA_PDC2027X=m
+CONFIG_SCSI_SATA_PROMISE=m
+# CONFIG_SCSI_SATA_SX4 is not set
+CONFIG_SCSI_SATA_SIL=m
+CONFIG_SCSI_SATA_SIS=m
+CONFIG_SCSI_SATA_VIA=m
+CONFIG_SCSI_SATA_VITESSE=m
+CONFIG_SCSI_BUSLOGIC=m
+# CONFIG_SCSI_OMIT_FLASHPOINT is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_DTC3280 is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_EATA_PIO is not set
+CONFIG_SCSI_FUTURE_DOMAIN=m
+CONFIG_SCSI_GDTH=m
+# CONFIG_SCSI_GENERIC_NCR5380 is not set
+# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
+CONFIG_SCSI_IPS=m
+CONFIG_SCSI_INIA100=m
+CONFIG_SCSI_PPA=m
+CONFIG_SCSI_IMM=m
+# CONFIG_SCSI_IZIP_EPP16 is not set
+# CONFIG_SCSI_IZIP_SLOW_CTR is not set
+# CONFIG_SCSI_NCR53C406A is not set
+CONFIG_SCSI_SYM53C8XX_2=y
+CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
+CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
+CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
+# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
+# CONFIG_SCSI_IPR is not set
+# CONFIG_SCSI_PAS16 is not set
+# CONFIG_SCSI_PSI240I is not set
+CONFIG_SCSI_QLOGIC_FAS=m
+CONFIG_SCSI_QLOGIC_ISP=m
+# CONFIG_SCSI_QLOGIC_FC is not set
+CONFIG_SCSI_QLOGIC_1280=m
+CONFIG_SCSI_QLA2XXX=y
+CONFIG_SCSI_QLA21XX=m
+CONFIG_SCSI_QLA22XX=m
+CONFIG_SCSI_QLA2300=m
+CONFIG_SCSI_QLA2322=m
+CONFIG_SCSI_QLA6312=m
+CONFIG_SCSI_QLA6322=m
+# CONFIG_SCSI_SYM53C416 is not set
+CONFIG_SCSI_DC395x=y
+CONFIG_SCSI_DC390T=y
+# CONFIG_SCSI_T128 is not set
+# CONFIG_SCSI_U14_34F is not set
+# CONFIG_SCSI_ULTRASTOR is not set
+# CONFIG_SCSI_NSP32 is not set
+# CONFIG_SCSI_DEBUG is not set
+
+#
+# PCMCIA SCSI adapter support
+#
+CONFIG_PCMCIA_AHA152X=m
+CONFIG_PCMCIA_FDOMAIN=m
+CONFIG_PCMCIA_NINJA_SCSI=m
+CONFIG_PCMCIA_QLOGIC=m
+# CONFIG_PCMCIA_SYM53C500 is not set
+
+#
+# Old CD-ROM drivers (not SCSI, not IDE)
+#
+# CONFIG_CD_NO_IDESCSI is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+# CONFIG_MD_RAID10 is not set
+CONFIG_MD_RAID5=m
+CONFIG_MD_RAID6=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+# CONFIG_DM_SNAPSHOT is not set
+# CONFIG_DM_MIRROR is not set
+# CONFIG_DM_ZERO is not set
+
+#
+# Fusion MPT device support
+#
+CONFIG_FUSION=m
+CONFIG_FUSION_MAX_SGE=40
+CONFIG_FUSION_CTL=m
+CONFIG_FUSION_LAN=m
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+CONFIG_I2O=m
+CONFIG_I2O_CONFIG=m
+CONFIG_I2O_BLOCK=m
+CONFIG_I2O_SCSI=m
+CONFIG_I2O_PROC=m
+
+#
+# Networking support
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_NETLINK_DEV=y
+CONFIG_UNIX=y
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_FWMARK=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+# CONFIG_IP_PNP is not set
+CONFIG_NET_IPIP=m
+CONFIG_NET_IPGRE=m
+CONFIG_NET_IPGRE_BROADCAST=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_TUNNEL=m
+
+#
+# IP: Virtual Server Configuration
+#
+CONFIG_IP_VS=m
+# CONFIG_IP_VS_DEBUG is not set
+CONFIG_IP_VS_TAB_BITS=12
+
+#
+# IPVS transport protocol load balancing support
+#
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+
+#
+# IPVS scheduler
+#
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+
+#
+# IPVS application helper
+#
+CONFIG_IP_VS_FTP=m
+CONFIG_IPV6=m
+CONFIG_IPV6_PRIVACY=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_INET6_TUNNEL=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_BRIDGE_NETFILTER=y
+
+#
+# IP: Netfilter Configuration
+#
+CONFIG_IP_NF_CONNTRACK=m
+# CONFIG_IP_NF_CT_ACCT is not set
+# CONFIG_IP_NF_CT_PROTO_SCTP is not set
+CONFIG_IP_NF_FTP=m
+CONFIG_IP_NF_IRC=m
+CONFIG_IP_NF_TFTP=m
+CONFIG_IP_NF_AMANDA=m
+CONFIG_IP_NF_QUEUE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_LIMIT=m
+CONFIG_IP_NF_MATCH_IPRANGE=m
+CONFIG_IP_NF_MATCH_MAC=m
+CONFIG_IP_NF_MATCH_PKTTYPE=m
+CONFIG_IP_NF_MATCH_MARK=m
+CONFIG_IP_NF_MATCH_MULTIPORT=m
+CONFIG_IP_NF_MATCH_TOS=m
+CONFIG_IP_NF_MATCH_RECENT=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_DSCP=m
+CONFIG_IP_NF_MATCH_AH_ESP=m
+CONFIG_IP_NF_MATCH_LENGTH=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_MATCH_TCPMSS=m
+CONFIG_IP_NF_MATCH_HELPER=m
+CONFIG_IP_NF_MATCH_STATE=m
+CONFIG_IP_NF_MATCH_CONNTRACK=m
+CONFIG_IP_NF_MATCH_OWNER=m
+CONFIG_IP_NF_MATCH_PHYSDEV=m
+# CONFIG_IP_NF_MATCH_ADDRTYPE is not set
+# CONFIG_IP_NF_MATCH_REALM is not set
+# CONFIG_IP_NF_MATCH_SCTP is not set
+# CONFIG_IP_NF_MATCH_COMMENT is not set
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_IP_NF_TARGET_TCPMSS=m
+CONFIG_IP_NF_NAT=m
+CONFIG_IP_NF_NAT_NEEDED=y
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
+CONFIG_IP_NF_TARGET_NETMAP=m
+CONFIG_IP_NF_TARGET_SAME=m
+CONFIG_IP_NF_NAT_LOCAL=y
+CONFIG_IP_NF_NAT_SNMP_BASIC=m
+CONFIG_IP_NF_NAT_IRC=m
+CONFIG_IP_NF_NAT_FTP=m
+CONFIG_IP_NF_NAT_TFTP=m
+CONFIG_IP_NF_NAT_AMANDA=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_TOS=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_DSCP=m
+CONFIG_IP_NF_TARGET_MARK=m
+CONFIG_IP_NF_TARGET_CLASSIFY=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_TARGET_NOTRACK=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
+# CONFIG_IP_NF_COMPAT_IPFWADM is not set
+
+#
+# IPv6: Netfilter Configuration
+#
+# CONFIG_IP6_NF_QUEUE is not set
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_LIMIT=m
+CONFIG_IP6_NF_MATCH_MAC=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_MULTIPORT=m
+CONFIG_IP6_NF_MATCH_OWNER=m
+CONFIG_IP6_NF_MATCH_MARK=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_AHESP=m
+CONFIG_IP6_NF_MATCH_LENGTH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+# CONFIG_IP6_NF_MATCH_PHYSDEV is not set
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_LOG=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_TARGET_MARK=m
+CONFIG_IP6_NF_RAW=m
+
+#
+# Bridge: Netfilter Configuration
+#
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=y
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+CONFIG_IP_SCTP=m
+# CONFIG_SCTP_DBG_MSG is not set
+# CONFIG_SCTP_DBG_OBJCNT is not set
+# CONFIG_SCTP_HMAC_NONE is not set
+# CONFIG_SCTP_HMAC_SHA1 is not set
+CONFIG_SCTP_HMAC_MD5=y
+# CONFIG_ATM is not set
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+# CONFIG_DECNET is not set
+CONFIG_LLC=m
+# CONFIG_LLC2 is not set
+CONFIG_IPX=m
+# CONFIG_IPX_INTERN is not set
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=y
+CONFIG_LTPC=m
+CONFIG_COPS=m
+CONFIG_COPS_DAYNA=y
+CONFIG_COPS_TANGENT=y
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_IPDDP_DECAP=y
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+CONFIG_NET_DIVERT=y
+# CONFIG_ECONET is not set
+CONFIG_WAN_ROUTER=m
+# CONFIG_NET_HW_FLOWCONTROL is not set
+
+#
+# QoS and/or fair queueing
+#
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CLK_JIFFIES=y
+# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set
+# CONFIG_NET_SCH_CLK_CPU is not set
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+# CONFIG_NET_SCH_NETEM is not set
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_QOS=y
+CONFIG_NET_ESTIMATOR=y
+CONFIG_NET_CLS=y
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_ROUTE=y
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+# CONFIG_CLS_U32_PERF is not set
+# CONFIG_NET_CLS_IND is not set
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+# CONFIG_NET_CLS_ACT is not set
+CONFIG_NET_CLS_POLICE=y
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+CONFIG_NETPOLL=y
+# CONFIG_NETPOLL_RX is not set
+# CONFIG_NETPOLL_TRAP is not set
+CONFIG_NET_POLL_CONTROLLER=y
+# CONFIG_HAMRADIO is not set
+CONFIG_IRDA=m
+
+#
+# IrDA protocols
+#
+CONFIG_IRLAN=m
+CONFIG_IRNET=m
+CONFIG_IRCOMM=m
+# CONFIG_IRDA_ULTRA is not set
+
+#
+# IrDA options
+#
+CONFIG_IRDA_CACHE_LAST_LSAP=y
+CONFIG_IRDA_FAST_RR=y
+# CONFIG_IRDA_DEBUG is not set
+
+#
+# Infrared-port device drivers
+#
+
+#
+# SIR device drivers
+#
+CONFIG_IRTTY_SIR=m
+
+#
+# Dongle support
+#
+CONFIG_DONGLE=y
+CONFIG_ESI_DONGLE=m
+CONFIG_ACTISYS_DONGLE=m
+CONFIG_TEKRAM_DONGLE=m
+CONFIG_LITELINK_DONGLE=m
+CONFIG_MA600_DONGLE=m
+CONFIG_GIRBIL_DONGLE=m
+CONFIG_MCP2120_DONGLE=m
+CONFIG_OLD_BELKIN_DONGLE=m
+CONFIG_ACT200L_DONGLE=m
+
+#
+# Old SIR device drivers
+#
+CONFIG_IRPORT_SIR=m
+
+#
+# Old Serial dongle support
+#
+# CONFIG_DONGLE_OLD is not set
+
+#
+# FIR device drivers
+#
+CONFIG_USB_IRDA=m
+CONFIG_SIGMATEL_FIR=m
+CONFIG_NSC_FIR=m
+# CONFIG_WINBOND_FIR is not set
+# CONFIG_TOSHIBA_FIR is not set
+# CONFIG_SMC_IRCC_FIR is not set
+# CONFIG_ALI_FIR is not set
+# CONFIG_VLSI_FIR is not set
+# CONFIG_VIA_FIR is not set
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+CONFIG_BT_SCO=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_CMTP=m
+# CONFIG_BT_HIDP is not set
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIUSB=m
+CONFIG_BT_HCIUSB_SCO=y
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_BCSP_TXCRC=y
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIDTL1=m
+CONFIG_BT_HCIBT3C=m
+CONFIG_BT_HCIBLUECARD=m
+CONFIG_BT_HCIBTUART=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+CONFIG_BONDING=m
+CONFIG_EQUALIZER=m
+CONFIG_TUN=m
+CONFIG_ETHERTAP=m
+CONFIG_NET_SB1000=m
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=m
+CONFIG_HAPPYMEAL=m
+CONFIG_SUNGEM=m
+CONFIG_NET_VENDOR_3COM=y
+CONFIG_EL1=m
+CONFIG_EL2=m
+CONFIG_ELPLUS=m
+CONFIG_EL16=m
+CONFIG_EL3=m
+CONFIG_3C515=m
+CONFIG_VORTEX=m
+# CONFIG_TYPHOON is not set
+CONFIG_LANCE=m
+CONFIG_NET_VENDOR_SMC=y
+CONFIG_WD80x3=m
+CONFIG_ULTRA=m
+CONFIG_SMC9194=m
+CONFIG_NET_VENDOR_RACAL=y
+# CONFIG_NI5010 is not set
+CONFIG_NI52=m
+CONFIG_NI65=m
+
+#
+# Tulip family network device support
+#
+CONFIG_NET_TULIP=y
+CONFIG_DE2104X=m
+CONFIG_TULIP=m
+# CONFIG_TULIP_MWI is not set
+CONFIG_TULIP_MMIO=y
+# CONFIG_TULIP_NAPI is not set
+CONFIG_DE4X5=m
+CONFIG_WINBOND_840=m
+CONFIG_DM9102=m
+CONFIG_PCMCIA_XIRCOM=m
+# CONFIG_PCMCIA_XIRTULIP is not set
+# CONFIG_AT1700 is not set
+CONFIG_DEPCA=m
+CONFIG_HP100=m
+# CONFIG_NET_ISA is not set
+CONFIG_NET_PCI=y
+CONFIG_PCNET32=m
+CONFIG_AMD8111_ETH=m
+CONFIG_AMD8111E_NAPI=y
+CONFIG_ADAPTEC_STARFIRE=m
+CONFIG_ADAPTEC_STARFIRE_NAPI=y
+CONFIG_AC3200=m
+CONFIG_APRICOT=m
+CONFIG_B44=m
+CONFIG_FORCEDETH=m
+CONFIG_CS89x0=m
+CONFIG_DGRS=m
+CONFIG_EEPRO100=m
+# CONFIG_EEPRO100_PIO is not set
+CONFIG_E100=m
+CONFIG_E100_NAPI=y
+CONFIG_FEALNX=m
+CONFIG_NATSEMI=m
+CONFIG_NE2K_PCI=m
+CONFIG_8139CP=m
+CONFIG_8139TOO=m
+CONFIG_8139TOO_PIO=y
+# CONFIG_8139TOO_TUNE_TWISTER is not set
+CONFIG_8139TOO_8129=y
+# CONFIG_8139_OLD_RX_RESET is not set
+CONFIG_SIS900=m
+CONFIG_EPIC100=m
+CONFIG_SUNDANCE=m
+# CONFIG_SUNDANCE_MMIO is not set
+CONFIG_TLAN=m
+CONFIG_VIA_RHINE=m
+CONFIG_VIA_RHINE_MMIO=y
+# CONFIG_VIA_VELOCITY is not set
+CONFIG_NET_POCKET=y
+CONFIG_ATP=m
+CONFIG_DE600=m
+CONFIG_DE620=m
+
+#
+# Ethernet (1000 Mbit)
+#
+CONFIG_ACENIC=m
+# CONFIG_ACENIC_OMIT_TIGON_I is not set
+CONFIG_DL2K=m
+CONFIG_E1000=m
+CONFIG_E1000_NAPI=y
+CONFIG_NS83820=m
+CONFIG_HAMACHI=m
+CONFIG_YELLOWFIN=m
+CONFIG_R8169=m
+# CONFIG_R8169_NAPI is not set
+CONFIG_SK98LIN=m
+CONFIG_TIGON3=m
+
+#
+# Ethernet (10000 Mbit)
+#
+CONFIG_IXGB=m
+CONFIG_IXGB_NAPI=y
+CONFIG_S2IO=m
+CONFIG_S2IO_NAPI=y
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN (non-hamradio)
+#
+CONFIG_NET_RADIO=y
+
+#
+# Obsolete Wireless cards support (pre-802.11)
+#
+# CONFIG_STRIP is not set
+# CONFIG_ARLAN is not set
+CONFIG_WAVELAN=m
+CONFIG_PCMCIA_WAVELAN=m
+CONFIG_PCMCIA_NETWAVE=m
+
+#
+# Wireless 802.11 Frequency Hopping cards support
+#
+# CONFIG_PCMCIA_RAYCS is not set
+
+#
+# Wireless 802.11b ISA/PCI cards support
+#
+CONFIG_AIRO=m
+CONFIG_HERMES=m
+CONFIG_PLX_HERMES=m
+CONFIG_TMD_HERMES=m
+CONFIG_PCI_HERMES=m
+CONFIG_ATMEL=m
+CONFIG_PCI_ATMEL=m
+
+#
+# Wireless 802.11b Pcmcia/Cardbus cards support
+#
+CONFIG_PCMCIA_HERMES=m
+CONFIG_AIRO_CS=m
+CONFIG_PCMCIA_ATMEL=m
+CONFIG_PCMCIA_WL3501=m
+
+#
+# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
+#
+CONFIG_PRISM54=m
+CONFIG_NET_WIRELESS=y
+
+#
+# PCMCIA network device support
+#
+CONFIG_NET_PCMCIA=y
+CONFIG_PCMCIA_3C589=m
+CONFIG_PCMCIA_3C574=m
+CONFIG_PCMCIA_FMVJ18X=m
+CONFIG_PCMCIA_PCNET=m
+CONFIG_PCMCIA_NMCLAN=m
+CONFIG_PCMCIA_SMC91C92=m
+CONFIG_PCMCIA_XIRC2PS=m
+CONFIG_PCMCIA_AXNET=m
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+CONFIG_FDDI=y
+# CONFIG_DEFXX is not set
+CONFIG_SKFP=m
+# CONFIG_HIPPI is not set
+CONFIG_PLIP=m
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+# CONFIG_PPP_BSDCOMP is not set
+CONFIG_PPPOE=m
+# CONFIG_SLIP is not set
+CONFIG_NET_FC=y
+# CONFIG_SHAPER is not set
+CONFIG_NETCONSOLE=m
+
+#
+# ISDN subsystem
+#
+CONFIG_ISDN=m
+
+#
+# Old ISDN4Linux
+#
+CONFIG_ISDN_I4L=m
+CONFIG_ISDN_PPP=y
+CONFIG_ISDN_PPP_VJ=y
+CONFIG_ISDN_MPP=y
+CONFIG_IPPP_FILTER=y
+# CONFIG_ISDN_PPP_BSDCOMP is not set
+CONFIG_ISDN_AUDIO=y
+CONFIG_ISDN_TTY_FAX=y
+
+#
+# ISDN feature submodules
+#
+CONFIG_ISDN_DRV_LOOP=m
+
+#
+# ISDN4Linux hardware drivers
+#
+
+#
+# Passive cards
+#
+CONFIG_ISDN_DRV_HISAX=m
+
+#
+# D-channel protocol features
+#
+CONFIG_HISAX_EURO=y
+CONFIG_DE_AOC=y
+CONFIG_HISAX_NO_SENDCOMPLETE=y
+CONFIG_HISAX_NO_LLC=y
+CONFIG_HISAX_NO_KEYPAD=y
+CONFIG_HISAX_1TR6=y
+CONFIG_HISAX_NI1=y
+CONFIG_HISAX_MAX_CARDS=8
+
+#
+# HiSax supported cards
+#
+CONFIG_HISAX_16_0=y
+CONFIG_HISAX_16_3=y
+CONFIG_HISAX_TELESPCI=y
+CONFIG_HISAX_S0BOX=y
+CONFIG_HISAX_AVM_A1=y
+CONFIG_HISAX_FRITZPCI=y
+CONFIG_HISAX_AVM_A1_PCMCIA=y
+CONFIG_HISAX_ELSA=y
+CONFIG_HISAX_IX1MICROR2=y
+CONFIG_HISAX_DIEHLDIVA=y
+CONFIG_HISAX_ASUSCOM=y
+CONFIG_HISAX_TELEINT=y
+CONFIG_HISAX_HFCS=y
+CONFIG_HISAX_SEDLBAUER=y
+CONFIG_HISAX_SPORTSTER=y
+CONFIG_HISAX_MIC=y
+CONFIG_HISAX_NETJET=y
+CONFIG_HISAX_NETJET_U=y
+CONFIG_HISAX_NICCY=y
+CONFIG_HISAX_ISURF=y
+CONFIG_HISAX_HSTSAPHIR=y
+CONFIG_HISAX_BKM_A4T=y
+CONFIG_HISAX_SCT_QUADRO=y
+CONFIG_HISAX_GAZEL=y
+CONFIG_HISAX_HFC_PCI=y
+CONFIG_HISAX_W6692=y
+CONFIG_HISAX_HFC_SX=y
+CONFIG_HISAX_ENTERNOW_PCI=y
+# CONFIG_HISAX_DEBUG is not set
+
+#
+# HiSax PCMCIA card service modules
+#
+CONFIG_HISAX_SEDLBAUER_CS=m
+CONFIG_HISAX_ELSA_CS=m
+CONFIG_HISAX_AVM_A1_CS=m
+CONFIG_HISAX_TELES_CS=m
+
+#
+# HiSax sub driver modules
+#
+CONFIG_HISAX_ST5481=m
+CONFIG_HISAX_HFCUSB=m
+CONFIG_HISAX_FRITZ_PCIPNP=m
+CONFIG_HISAX_HDLC=y
+
+#
+# Active cards
+#
+CONFIG_ISDN_DRV_ICN=m
+CONFIG_ISDN_DRV_PCBIT=m
+CONFIG_ISDN_DRV_SC=m
+CONFIG_ISDN_DRV_ACT2000=m
+CONFIG_ISDN_DRV_TPAM=m
+CONFIG_HYSDN=m
+CONFIG_HYSDN_CAPI=y
+
+#
+# CAPI subsystem
+#
+CONFIG_ISDN_CAPI=m
+CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON=y
+CONFIG_ISDN_CAPI_MIDDLEWARE=y
+CONFIG_ISDN_CAPI_CAPI20=m
+CONFIG_ISDN_CAPI_CAPIFS_BOOL=y
+CONFIG_ISDN_CAPI_CAPIFS=m
+CONFIG_ISDN_CAPI_CAPIDRV=m
+
+#
+# CAPI hardware drivers
+#
+
+#
+# Active AVM cards
+#
+CONFIG_CAPI_AVM=y
+CONFIG_ISDN_DRV_AVMB1_B1ISA=m
+CONFIG_ISDN_DRV_AVMB1_B1PCI=m
+CONFIG_ISDN_DRV_AVMB1_B1PCIV4=y
+CONFIG_ISDN_DRV_AVMB1_T1ISA=m
+CONFIG_ISDN_DRV_AVMB1_B1PCMCIA=m
+CONFIG_ISDN_DRV_AVMB1_AVM_CS=m
+CONFIG_ISDN_DRV_AVMB1_T1PCI=m
+CONFIG_ISDN_DRV_AVMB1_C4=m
+
+#
+# Active Eicon DIVA Server cards
+#
+CONFIG_CAPI_EICON=y
+CONFIG_ISDN_DIVAS=m
+CONFIG_ISDN_DIVAS_BRIPCI=y
+CONFIG_ISDN_DIVAS_PRIPCI=y
+CONFIG_ISDN_DIVAS_DIVACAPI=m
+CONFIG_ISDN_DIVAS_USERIDI=m
+CONFIG_ISDN_DIVAS_MAINT=m
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+CONFIG_INPUT_JOYDEV=m
+# CONFIG_INPUT_TSDEV is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input I/O drivers
+#
+CONFIG_GAMEPORT=m
+CONFIG_SOUND_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_GAMEPORT_EMU10K1=m
+CONFIG_GAMEPORT_VORTEX=m
+CONFIG_GAMEPORT_FM801=m
+CONFIG_GAMEPORT_CS461x=m
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_CT82C710 is not set
+# CONFIG_SERIO_PARKBD is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_SERIAL=m
+CONFIG_MOUSE_INPORT=m
+CONFIG_MOUSE_ATIXL=y
+CONFIG_MOUSE_LOGIBM=m
+CONFIG_MOUSE_PC110PAD=m
+CONFIG_MOUSE_VSXXXAA=m
+CONFIG_INPUT_JOYSTICK=y
+CONFIG_JOYSTICK_ANALOG=m
+CONFIG_JOYSTICK_A3D=m
+CONFIG_JOYSTICK_ADI=m
+CONFIG_JOYSTICK_COBRA=m
+CONFIG_JOYSTICK_GF2K=m
+CONFIG_JOYSTICK_GRIP=m
+CONFIG_JOYSTICK_GRIP_MP=m
+CONFIG_JOYSTICK_GUILLEMOT=m
+CONFIG_JOYSTICK_INTERACT=m
+CONFIG_JOYSTICK_SIDEWINDER=m
+CONFIG_JOYSTICK_TMDC=m
+CONFIG_JOYSTICK_IFORCE=m
+CONFIG_JOYSTICK_IFORCE_USB=y
+CONFIG_JOYSTICK_IFORCE_232=y
+CONFIG_JOYSTICK_WARRIOR=m
+CONFIG_JOYSTICK_MAGELLAN=m
+CONFIG_JOYSTICK_SPACEORB=m
+CONFIG_JOYSTICK_SPACEBALL=m
+CONFIG_JOYSTICK_STINGER=m
+CONFIG_JOYSTICK_TWIDDLER=m
+CONFIG_JOYSTICK_DB9=m
+CONFIG_JOYSTICK_GAMECON=m
+CONFIG_JOYSTICK_TURBOGRAFX=m
+# CONFIG_JOYSTICK_JOYDUMP is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_GUNZE=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_PCSPKR=m
+# CONFIG_INPUT_UINPUT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_SERIAL_NONSTANDARD=y
+# CONFIG_COMPUTONE is not set
+CONFIG_ROCKETPORT=m
+# CONFIG_CYCLADES is not set
+# CONFIG_DIGIEPCA is not set
+# CONFIG_DIGI is not set
+# CONFIG_ESPSERIAL is not set
+# CONFIG_MOXA_INTELLIO is not set
+# CONFIG_MOXA_SMARTIO is not set
+# CONFIG_ISI is not set
+CONFIG_SYNCLINK=m
+CONFIG_SYNCLINKMP=m
+CONFIG_N_HDLC=m
+# CONFIG_RISCOM8 is not set
+# CONFIG_SPECIALIX is not set
+# CONFIG_SX is not set
+# CONFIG_RIO is not set
+CONFIG_STALDRV=y
+# CONFIG_STALLION is not set
+# CONFIG_ISTALLION is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_CS=m
+# CONFIG_SERIAL_8250_ACPI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_MULTIPORT=y
+CONFIG_SERIAL_8250_RSA=y
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_PRINTER=m
+CONFIG_LP_CONSOLE=y
+CONFIG_PPDEV=m
+CONFIG_TIPAR=m
+
+#
+# IPMI
+#
+CONFIG_IPMI_HANDLER=m
+# CONFIG_IPMI_PANIC_EVENT is not set
+CONFIG_IPMI_DEVICE_INTERFACE=m
+CONFIG_IPMI_SI=m
+CONFIG_IPMI_WATCHDOG=m
+# CONFIG_IPMI_POWEROFF is not set
+
+#
+# Watchdog Cards
+#
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+CONFIG_SOFT_WATCHDOG=m
+CONFIG_ACQUIRE_WDT=m
+CONFIG_ADVANTECH_WDT=m
+CONFIG_ALIM1535_WDT=m
+CONFIG_ALIM7101_WDT=m
+CONFIG_SC520_WDT=m
+CONFIG_EUROTECH_WDT=m
+CONFIG_IB700_WDT=m
+CONFIG_WAFER_WDT=m
+CONFIG_I8XX_TCO=m
+CONFIG_SC1200_WDT=m
+# CONFIG_SCx200_WDT is not set
+# CONFIG_60XX_WDT is not set
+CONFIG_CPU5_WDT=m
+CONFIG_W83627HF_WDT=m
+CONFIG_W83877F_WDT=m
+CONFIG_MACHZ_WDT=m
+
+#
+# ISA-based Watchdog Cards
+#
+CONFIG_PCWATCHDOG=m
+# CONFIG_MIXCOMWD is not set
+CONFIG_WDT=m
+# CONFIG_WDT_501 is not set
+
+#
+# PCI-based Watchdog Cards
+#
+CONFIG_PCIPCWATCHDOG=m
+CONFIG_WDTPCI=m
+CONFIG_WDT_501_PCI=y
+
+#
+# USB-based Watchdog Cards
+#
+CONFIG_USBPCWATCHDOG=m
+CONFIG_HW_RANDOM=m
+CONFIG_NVRAM=m
+CONFIG_RTC=y
+CONFIG_DTLK=m
+CONFIG_R3964=m
+# CONFIG_APPLICOM is not set
+CONFIG_SONYPI=m
+
+#
+# Ftape, the floppy tape device driver
+#
+# CONFIG_FTAPE is not set
+CONFIG_AGP=y
+CONFIG_AGP_ALI=y
+CONFIG_AGP_ATI=y
+CONFIG_AGP_AMD=y
+CONFIG_AGP_AMD64=y
+CONFIG_AGP_INTEL=y
+CONFIG_AGP_INTEL_MCH=y
+CONFIG_AGP_NVIDIA=y
+CONFIG_AGP_SIS=y
+CONFIG_AGP_SWORKS=y
+CONFIG_AGP_VIA=y
+CONFIG_AGP_EFFICEON=y
+CONFIG_DRM=y
+CONFIG_DRM_TDFX=m
+CONFIG_DRM_R128=m
+CONFIG_DRM_RADEON=m
+CONFIG_DRM_I810=m
+# CONFIG_DRM_I830 is not set
+# CONFIG_DRM_I915 is not set
+CONFIG_DRM_MGA=m
+CONFIG_DRM_SIS=m
+
+#
+# PCMCIA character devices
+#
+CONFIG_SYNCLINK_CS=m
+CONFIG_MWAVE=m
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_HPET is not set
+CONFIG_HANGCHECK_TIMER=m
+
+#
+# I2C support
+#
+CONFIG_I2C=m
+CONFIG_I2C_CHARDEV=m
+
+#
+# I2C Algorithms
+#
+CONFIG_I2C_ALGOBIT=m
+CONFIG_I2C_ALGOPCF=m
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+CONFIG_I2C_ALI1535=m
+CONFIG_I2C_ALI1563=m
+CONFIG_I2C_ALI15X3=m
+CONFIG_I2C_AMD756=m
+CONFIG_I2C_AMD8111=m
+# CONFIG_I2C_ELEKTOR is not set
+CONFIG_I2C_I801=m
+CONFIG_I2C_I810=m
+CONFIG_I2C_ISA=m
+CONFIG_I2C_NFORCE2=m
+# CONFIG_I2C_PARPORT is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+CONFIG_I2C_PIIX4=m
+CONFIG_I2C_PROSAVAGE=m
+CONFIG_I2C_SAVAGE4=m
+# CONFIG_SCx200_ACB is not set
+CONFIG_I2C_SIS5595=m
+CONFIG_I2C_SIS630=m
+CONFIG_I2C_SIS96X=m
+CONFIG_I2C_VIA=m
+CONFIG_I2C_VIAPRO=m
+CONFIG_I2C_VOODOO3=m
+# CONFIG_I2C_PCA_ISA is not set
+
+#
+# Hardware Sensors Chip support
+#
+CONFIG_I2C_SENSOR=m
+CONFIG_SENSORS_ADM1021=m
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+CONFIG_SENSORS_ASB100=m
+CONFIG_SENSORS_DS1621=m
+CONFIG_SENSORS_FSCHER=m
+CONFIG_SENSORS_GL518SM=m
+CONFIG_SENSORS_IT87=m
+CONFIG_SENSORS_LM75=m
+# CONFIG_SENSORS_LM77 is not set
+CONFIG_SENSORS_LM78=m
+CONFIG_SENSORS_LM80=m
+CONFIG_SENSORS_LM83=m
+CONFIG_SENSORS_LM85=m
+CONFIG_SENSORS_LM90=m
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+CONFIG_SENSORS_VIA686A=m
+CONFIG_SENSORS_W83781D=m
+CONFIG_SENSORS_W83L785TS=m
+CONFIG_SENSORS_W83627HF=m
+
+#
+# Other I2C Chip support
+#
+CONFIG_SENSORS_EEPROM=m
+CONFIG_SENSORS_PCF8574=m
+CONFIG_SENSORS_PCF8591=m
+# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Misc devices
+#
+CONFIG_IBM_ASM=m
+
+#
+# Multimedia devices
+#
+CONFIG_VIDEO_DEV=m
+
+#
+# Video For Linux
+#
+
+#
+# Video Adapters
+#
+CONFIG_VIDEO_BT848=m
+CONFIG_VIDEO_PMS=m
+CONFIG_VIDEO_BWQCAM=m
+CONFIG_VIDEO_CQCAM=m
+CONFIG_VIDEO_W9966=m
+CONFIG_VIDEO_CPIA=m
+CONFIG_VIDEO_CPIA_PP=m
+CONFIG_VIDEO_CPIA_USB=m
+CONFIG_VIDEO_SAA5246A=m
+CONFIG_VIDEO_SAA5249=m
+CONFIG_TUNER_3036=m
+CONFIG_VIDEO_STRADIS=m
+CONFIG_VIDEO_ZORAN=m
+CONFIG_VIDEO_ZORAN_BUZ=m
+CONFIG_VIDEO_ZORAN_DC10=m
+CONFIG_VIDEO_ZORAN_DC30=m
+CONFIG_VIDEO_ZORAN_LML33=m
+CONFIG_VIDEO_ZORAN_LML33R10=m
+CONFIG_VIDEO_MEYE=m
+CONFIG_VIDEO_SAA7134=m
+CONFIG_VIDEO_MXB=m
+CONFIG_VIDEO_DPC=m
+CONFIG_VIDEO_HEXIUM_ORION=m
+CONFIG_VIDEO_HEXIUM_GEMINI=m
+CONFIG_VIDEO_CX88=m
+# CONFIG_VIDEO_OVCAMCHIP is not set
+
+#
+# Radio Adapters
+#
+CONFIG_RADIO_CADET=m
+CONFIG_RADIO_RTRACK=m
+CONFIG_RADIO_RTRACK2=m
+CONFIG_RADIO_AZTECH=m
+CONFIG_RADIO_GEMTEK=m
+CONFIG_RADIO_GEMTEK_PCI=m
+CONFIG_RADIO_MAXIRADIO=m
+CONFIG_RADIO_MAESTRO=m
+CONFIG_RADIO_SF16FMI=m
+CONFIG_RADIO_SF16FMR2=m
+CONFIG_RADIO_TERRATEC=m
+CONFIG_RADIO_TRUST=m
+CONFIG_RADIO_TYPHOON=m
+CONFIG_RADIO_TYPHOON_PROC_FS=y
+CONFIG_RADIO_ZOLTRIX=m
+
+#
+# Digital Video Broadcasting Devices
+#
+CONFIG_DVB=y
+CONFIG_DVB_CORE=m
+
+#
+# Supported Frontend Modules
+#
+CONFIG_DVB_TWINHAN_DST=m
+CONFIG_DVB_STV0299=m
+# CONFIG_DVB_SP887X is not set
+# CONFIG_DVB_ALPS_TDLB7 is not set
+CONFIG_DVB_ALPS_TDMB7=m
+CONFIG_DVB_ATMEL_AT76C651=m
+CONFIG_DVB_CX24110=m
+CONFIG_DVB_GRUNDIG_29504_491=m
+CONFIG_DVB_GRUNDIG_29504_401=m
+CONFIG_DVB_MT312=m
+CONFIG_DVB_VES1820=m
+CONFIG_DVB_VES1X93=m
+# CONFIG_DVB_TDA1004X is not set
+CONFIG_DVB_NXT6000=m
+
+#
+# Supported SAA7146 based PCI Adapters
+#
+CONFIG_DVB_AV7110=m
+CONFIG_DVB_AV7110_OSD=y
+CONFIG_DVB_BUDGET=m
+CONFIG_DVB_BUDGET_CI=m
+CONFIG_DVB_BUDGET_AV=m
+CONFIG_DVB_BUDGET_PATCH=m
+
+#
+# Supported USB Adapters
+#
+CONFIG_DVB_TTUSB_BUDGET=m
+CONFIG_DVB_TTUSB_DEC=m
+
+#
+# Supported FlexCopII (B2C2) Adapters
+#
+CONFIG_DVB_B2C2_SKYSTAR=m
+
+#
+# Supported BT878 Adapters
+#
+CONFIG_DVB_BT8XX=m
+CONFIG_VIDEO_SAA7146=m
+CONFIG_VIDEO_SAA7146_VV=m
+CONFIG_VIDEO_VIDEOBUF=m
+CONFIG_VIDEO_TUNER=m
+CONFIG_VIDEO_BUF=m
+CONFIG_VIDEO_BTCX=m
+CONFIG_VIDEO_IR=m
+
+#
+# Graphics support
+#
+CONFIG_FB=y
+CONFIG_FB_MODE_HELPERS=y
+# CONFIG_FB_CIRRUS is not set
+# CONFIG_FB_PM2 is not set
+# CONFIG_FB_CYBER2000 is not set
+# CONFIG_FB_ASILIANT is not set
+# CONFIG_FB_IMSTT is not set
+CONFIG_FB_VGA16=m
+CONFIG_FB_VESA=y
+CONFIG_VIDEO_SELECT=y
+CONFIG_FB_HGA=m
+# CONFIG_FB_HGA_ACCEL is not set
+CONFIG_FB_RIVA=m
+# CONFIG_FB_RIVA_I2C is not set
+# CONFIG_FB_RIVA_DEBUG is not set
+CONFIG_FB_I810=m
+CONFIG_FB_I810_GTF=y
+CONFIG_FB_MATROX=m
+CONFIG_FB_MATROX_MILLENIUM=y
+CONFIG_FB_MATROX_MYSTIQUE=y
+CONFIG_FB_MATROX_G450=y
+CONFIG_FB_MATROX_G100=y
+CONFIG_FB_MATROX_I2C=m
+CONFIG_FB_MATROX_MAVEN=m
+CONFIG_FB_MATROX_MULTIHEAD=y
+# CONFIG_FB_RADEON_OLD is not set
+CONFIG_FB_RADEON=m
+CONFIG_FB_RADEON_I2C=y
+# CONFIG_FB_RADEON_DEBUG is not set
+CONFIG_FB_ATY128=m
+CONFIG_FB_ATY=m
+CONFIG_FB_ATY_CT=y
+CONFIG_FB_ATY_GX=y
+# CONFIG_FB_ATY_XL_INIT is not set
+# CONFIG_FB_SIS is not set
+CONFIG_FB_NEOMAGIC=m
+CONFIG_FB_KYRO=m
+CONFIG_FB_3DFX=m
+# CONFIG_FB_3DFX_ACCEL is not set
+CONFIG_FB_VOODOO1=m
+CONFIG_FB_TRIDENT=m
+# CONFIG_FB_TRIDENT_ACCEL is not set
+# CONFIG_FB_VIRTUAL is not set
+
+#
+# Console display driver support
+#
+CONFIG_VGA_CONSOLE=y
+CONFIG_MDA_CONSOLE=m
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+
+#
+# Logo configuration
+#
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+
+#
+# Sound
+#
+CONFIG_SOUND=m
+
+#
+# Advanced Linux Sound Architecture
+#
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+CONFIG_SND_HWDEP=m
+CONFIG_SND_RAWMIDI=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_RTCTIMER=m
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+
+#
+# Generic devices
+#
+CONFIG_SND_MPU401_UART=m
+CONFIG_SND_OPL3_LIB=m
+CONFIG_SND_OPL4_LIB=m
+CONFIG_SND_VX_LIB=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+# CONFIG_SND_SERIAL_U16550 is not set
+CONFIG_SND_MPU401=m
+
+#
+# ISA devices
+#
+CONFIG_SND_AD1816A=m
+CONFIG_SND_AD1848=m
+CONFIG_SND_CS4231=m
+CONFIG_SND_CS4232=m
+CONFIG_SND_CS4236=m
+CONFIG_SND_ES968=m
+CONFIG_SND_ES1688=m
+CONFIG_SND_ES18XX=m
+CONFIG_SND_GUS_SYNTH=m
+CONFIG_SND_GUSCLASSIC=m
+CONFIG_SND_GUSEXTREME=m
+CONFIG_SND_GUSMAX=m
+CONFIG_SND_INTERWAVE=m
+CONFIG_SND_INTERWAVE_STB=m
+CONFIG_SND_OPTI92X_AD1848=m
+CONFIG_SND_OPTI92X_CS4231=m
+CONFIG_SND_OPTI93X=m
+CONFIG_SND_SB8=m
+CONFIG_SND_SB16=m
+CONFIG_SND_SBAWE=m
+CONFIG_SND_SB16_CSP=y
+# CONFIG_SND_WAVEFRONT is not set
+CONFIG_SND_ALS100=m
+CONFIG_SND_AZT2320=m
+CONFIG_SND_CMI8330=m
+CONFIG_SND_DT019X=m
+CONFIG_SND_OPL3SA2=m
+CONFIG_SND_SGALAXY=m
+CONFIG_SND_SSCAPE=m
+
+#
+# PCI devices
+#
+CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_ALI5451=m
+CONFIG_SND_ATIIXP=m
+# CONFIG_SND_ATIIXP_MODEM is not set
+CONFIG_SND_AU8810=m
+CONFIG_SND_AU8820=m
+CONFIG_SND_AU8830=m
+CONFIG_SND_AZT3328=m
+CONFIG_SND_BT87X=m
+CONFIG_SND_CS46XX=m
+CONFIG_SND_CS46XX_NEW_DSP=y
+CONFIG_SND_CS4281=m
+CONFIG_SND_EMU10K1=m
+CONFIG_SND_KORG1212=m
+CONFIG_SND_MIXART=m
+CONFIG_SND_NM256=m
+CONFIG_SND_RME32=m
+CONFIG_SND_RME96=m
+CONFIG_SND_RME9652=m
+CONFIG_SND_HDSP=m
+CONFIG_SND_TRIDENT=m
+CONFIG_SND_YMFPCI=m
+CONFIG_SND_ALS4000=m
+CONFIG_SND_CMIPCI=m
+CONFIG_SND_ENS1370=m
+CONFIG_SND_ENS1371=m
+CONFIG_SND_ES1938=m
+CONFIG_SND_ES1968=m
+CONFIG_SND_MAESTRO3=m
+CONFIG_SND_FM801=m
+CONFIG_SND_FM801_TEA575X=m
+CONFIG_SND_ICE1712=m
+CONFIG_SND_ICE1724=m
+CONFIG_SND_INTEL8X0=m
+CONFIG_SND_INTEL8X0M=m
+CONFIG_SND_SONICVIBES=m
+CONFIG_SND_VIA82XX=m
+CONFIG_SND_VX222=m
+
+#
+# ALSA USB devices
+#
+CONFIG_SND_USB_AUDIO=m
+# CONFIG_SND_USB_USX2Y is not set
+
+#
+# PCMCIA devices
+#
+# CONFIG_SND_VXPOCKET is not set
+# CONFIG_SND_VXP440 is not set
+CONFIG_SND_PDAUDIOCF=m
+
+#
+# Open Sound System
+#
+# CONFIG_SOUND_PRIME is not set
+
+#
+# USB support
+#
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_BANDWIDTH is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+CONFIG_USB_EHCI_HCD=m
+CONFIG_USB_EHCI_SPLIT_ISO=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_UHCI_HCD=m
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_AUDIO=m
+
+#
+# USB Bluetooth TTY can only be used with disabled Bluetooth subsystem
+#
+CONFIG_USB_MIDI=m
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_RW_DETECT is not set
+CONFIG_USB_STORAGE_DATAFAB=y
+CONFIG_USB_STORAGE_FREECOM=y
+CONFIG_USB_STORAGE_DPCM=y
+CONFIG_USB_STORAGE_HP8200e=y
+CONFIG_USB_STORAGE_SDDR09=y
+CONFIG_USB_STORAGE_SDDR55=y
+CONFIG_USB_STORAGE_JUMPSHOT=y
+
+#
+# USB Human Interface Devices (HID)
+#
+CONFIG_USB_HID=y
+CONFIG_USB_HIDINPUT=y
+CONFIG_HID_FF=y
+CONFIG_HID_PID=y
+CONFIG_LOGITECH_FF=y
+CONFIG_THRUSTMASTER_FF=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB_AIPTEK=m
+CONFIG_USB_WACOM=m
+CONFIG_USB_KBTAB=m
+CONFIG_USB_POWERMATE=m
+CONFIG_USB_MTOUCH=m
+# CONFIG_USB_EGALAX is not set
+CONFIG_USB_XPAD=m
+CONFIG_USB_ATI_REMOTE=m
+
+#
+# USB Imaging devices
+#
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_HPUSBSCSI=m
+
+#
+# USB Multimedia devices
+#
+CONFIG_USB_DABUSB=m
+CONFIG_USB_VICAM=m
+CONFIG_USB_DSBR=m
+CONFIG_USB_IBMCAM=m
+CONFIG_USB_KONICAWC=m
+CONFIG_USB_OV511=m
+CONFIG_USB_SE401=m
+# CONFIG_USB_SN9C102 is not set
+CONFIG_USB_STV680=m
+
+#
+# USB Network adaptors
+#
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=m
+
+#
+# USB Host-to-Host Cables
+#
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_BELKIN=y
+CONFIG_USB_GENESYS=y
+CONFIG_USB_NET1080=y
+CONFIG_USB_PL2301=y
+
+#
+# Intelligent USB Devices/Gadgets
+#
+CONFIG_USB_ARMLINUX=y
+CONFIG_USB_EPSON2888=y
+CONFIG_USB_ZAURUS=y
+CONFIG_USB_CDCETHER=y
+
+#
+# USB Network Adapters
+#
+CONFIG_USB_AX8817X=y
+
+#
+# USB port drivers
+#
+CONFIG_USB_USS720=m
+
+#
+# USB Serial Converter support
+#
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KEYSPAN_MPR=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28X=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28XA=y
+CONFIG_USB_SERIAL_KEYSPAN_USA28XB=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19=y
+CONFIG_USB_SERIAL_KEYSPAN_USA18X=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19W=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
+CONFIG_USB_SERIAL_KEYSPAN_USA19QI=y
+CONFIG_USB_SERIAL_KEYSPAN_USA49W=y
+CONFIG_USB_SERIAL_KEYSPAN_USA49WLC=y
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SAFE_PADDED=y
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_XIRCOM=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_EZUSB=y
+
+#
+# USB Miscellaneous drivers
+#
+CONFIG_USB_EMI62=m
+# CONFIG_USB_EMI26 is not set
+CONFIG_USB_TIGL=m
+CONFIG_USB_AUERSWALD=m
+CONFIG_USB_RIO500=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_LED=m
+CONFIG_USB_CYTHERM=m
+# CONFIG_USB_PHIDGETSERVO is not set
+CONFIG_USB_TEST=m
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+CONFIG_REISERFS_FS=m
+# CONFIG_REISERFS_CHECK is not set
+CONFIG_REISERFS_PROC_INFO=y
+# CONFIG_REISERFS_FS_XATTR is not set
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+# CONFIG_JFS_DEBUG is not set
+# CONFIG_JFS_STATISTICS is not set
+CONFIG_FS_POSIX_ACL=y
+CONFIG_XFS_FS=m
+# CONFIG_XFS_RT is not set
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_SECURITY=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_MINIX_FS=m
+CONFIG_ROMFS_FS=m
+CONFIG_QUOTA=y
+# CONFIG_QFMT_V1 is not set
+CONFIG_QFMT_V2=y
+CONFIG_QUOTACTL=y
+CONFIG_AUTOFS_FS=m
+CONFIG_AUTOFS4_FS=m
+
+#
+# CD-ROM/DVD Filesystems
+#
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_ZISOFS_FS=y
+CONFIG_UDF_FS=m
+CONFIG_UDF_NLS=y
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_SYSFS=y
+# CONFIG_DEVFS_FS is not set
+CONFIG_DEVPTS_FS_XATTR=y
+CONFIG_DEVPTS_FS_SECURITY=y
+CONFIG_TMPFS=y
+CONFIG_HUGETLBFS=y
+CONFIG_HUGETLB_PAGE=y
+CONFIG_RAMFS=y
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+CONFIG_AFFS_FS=m
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
+CONFIG_BEFS_FS=m
+# CONFIG_BEFS_DEBUG is not set
+CONFIG_BFS_FS=m
+CONFIG_EFS_FS=m
+# CONFIG_JFFS_FS is not set
+CONFIG_JFFS2_FS=m
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_NAND=y
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=m
+CONFIG_VXFS_FS=m
+# CONFIG_HPFS_FS is not set
+CONFIG_QNX4FS_FS=m
+# CONFIG_QNX4FS_RW is not set
+CONFIG_SYSV_FS=m
+CONFIG_UFS_FS=m
+# CONFIG_UFS_FS_WRITE is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_DIRECTIO=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3=y
+CONFIG_NFSD_V4=y
+CONFIG_NFSD_TCP=y
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=m
+CONFIG_SUNRPC=m
+CONFIG_SUNRPC_GSS=m
+CONFIG_RPCSEC_GSS_KRB5=m
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+CONFIG_SMB_FS=m
+# CONFIG_SMB_NLS_DEFAULT is not set
+CONFIG_CIFS=m
+# CONFIG_CIFS_STATS is not set
+# CONFIG_CIFS_XATTR is not set
+# CONFIG_CIFS_POSIX is not set
+CONFIG_NCP_FS=m
+CONFIG_NCPFS_PACKET_SIGNING=y
+CONFIG_NCPFS_IOCTL_LOCKING=y
+CONFIG_NCPFS_STRONG=y
+CONFIG_NCPFS_NFS_NS=y
+CONFIG_NCPFS_OS2_NS=y
+CONFIG_NCPFS_SMALLDOS=y
+CONFIG_NCPFS_NLS=y
+CONFIG_NCPFS_EXTRAS=y
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+CONFIG_OSF_PARTITION=y
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+CONFIG_MAC_PARTITION=y
+CONFIG_MSDOS_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+# CONFIG_LDM_PARTITION is not set
+CONFIG_SGI_PARTITION=y
+# CONFIG_ULTRIX_PARTITION is not set
+CONFIG_SUN_PARTITION=y
+CONFIG_EFI_PARTITION=y
+
+#
+# Native Language Support
+#
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+# CONFIG_NLS_ASCII is not set
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+
+#
+# Profiling support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+CONFIG_DEBUG_SPINLOCK_SLEEP=y
+CONFIG_DEBUG_HIGHMEM=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_FRAME_POINTER is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_KPROBES is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_4KSTACKS is not set
+# CONFIG_SCHEDSTATS is not set
+
+#
+# Security options
+#
+CONFIG_SECURITY=y
+CONFIG_SECURITY_NETWORK=y
+CONFIG_SECURITY_CAPABILITIES=y
+# CONFIG_SECURITY_ROOTPLUG is not set
+CONFIG_SECURITY_SELINUX=y
+CONFIG_SECURITY_SELINUX_BOOTPARAM=y
+CONFIG_SECURITY_SELINUX_BOOTPARAM_VALUE=1
+CONFIG_SECURITY_SELINUX_DISABLE=y
+CONFIG_SECURITY_SELINUX_DEVELOP=y
+# CONFIG_SECURITY_SELINUX_MLS is not set
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+# CONFIG_CRYPTO_WP512 is not set
+CONFIG_CRYPTO_DES=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_SERPENT=m
+# CONFIG_CRYPTO_AES_586 is not set
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+# CONFIG_CRYPTO_TEA is not set
+CONFIG_CRYPTO_ARC4=m
+# CONFIG_CRYPTO_KHAZAD is not set
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Library routines
+#
+CONFIG_CRC_CCITT=m
+CONFIG_CRC32=y
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=m
+CONFIG_X86_BIOS_REBOOT=y
+CONFIG_PC=y
diff -Nru linux-2.6.9-ori/drivers/scsi/Kconfig linux-2.6.9-mod/drivers/scsi/Kconfig
--- linux-2.6.9-ori/drivers/scsi/Kconfig 2004-10-19 05:55:07.000000000 +0800
+++ linux-2.6.9-mod/drivers/scsi/Kconfig 2004-10-21 11:31:29.000000000 +0800
@@ -433,6 +433,14 @@
If unsure, say N.
+config SCSI_PATA_PDC2027X
+ tristate "Promise PATA 2027x support"
+ depends on SCSI_SATA && PCI
+ help
+ This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+
+ If unsure, say N.
+
config SCSI_SATA_PROMISE
tristate "Promise SATA TX2/TX4 support"
depends on SCSI_SATA && PCI
diff -Nru linux-2.6.9-ori/drivers/scsi/Makefile linux-2.6.9-mod/drivers/scsi/Makefile
--- linux-2.6.9-ori/drivers/scsi/Makefile 2004-10-19 05:54:55.000000000 +0800
+++ linux-2.6.9-mod/drivers/scsi/Makefile 2004-10-21 11:31:03.000000000 +0800
@@ -123,6 +123,7 @@
obj-$(CONFIG_SCSI_IBMVSCSI) += ibmvscsi/
obj-$(CONFIG_SCSI_SATA_SVW) += libata.o sata_svw.o
obj-$(CONFIG_SCSI_ATA_PIIX) += libata.o ata_piix.o
+obj-$(CONFIG_SCSI_PATA_PDC2027X)+= libata.o pata_pdc2027x.o
obj-$(CONFIG_SCSI_SATA_PROMISE) += libata.o sata_promise.o
obj-$(CONFIG_SCSI_SATA_SIL) += libata.o sata_sil.o
obj-$(CONFIG_SCSI_SATA_VIA) += libata.o sata_via.o
diff -Nru linux-2.6.9-ori/drivers/scsi/pata_pdc2027x.c linux-2.6.9-mod/drivers/scsi/pata_pdc2027x.c
--- linux-2.6.9-ori/drivers/scsi/pata_pdc2027x.c 1970-01-01 08:00:00.000000000 +0800
+++ linux-2.6.9-mod/drivers/scsi/pata_pdc2027x.c 2004-10-21 16:44:32.775328632 +0800
@@ -0,0 +1,694 @@
+/*
+ * Promise PATA TX2/TX4/TX2000/133 IDE driver for pdc20268 to pdc20277.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Ported to libata by:
+ * Albert Lee <albertcc@tw.ibm.com> IBM Corporation
+ *
+ * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 1999 Promise Technology, Inc.
+ *
+ * Author: Frank Tiernan (frankt@promise.com)
+ * Released under terms of General Public License
+ *
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include "scsi.h"
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <asm/io.h>
+
+#define DRV_NAME "pata_pdc2027x"
+#define DRV_VERSION "0.53"
+#define PDC_DEBUG
+
+#ifdef PDC_DEBUG
+#define PDPRINTK(fmt, args...) printk(KERN_DEBUG "%s: " fmt, __FUNCTION__, ## args)
+#else
+#define PDPRINTK(fmt, args...)
+#endif
+
+enum {
+ PDC_UDMA_100 = 0,
+ PDC_UDMA_133 = 1,
+
+ PDC_100_MHZ = 100000000,
+ PDC_133_MHZ = 133333333,
+};
+
+static int pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+static void pdc2027x_remove_one(struct pci_dev *pdev);
+static void pdc2027x_phy_reset(struct ata_port *ap);
+static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev);
+static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev);
+
+/*
+ * ATA Timing Tables based on 133MHz controller clock.
+ * These tables are only used when the controller is in 133MHz clock.
+ * If the controller is in 100MHz clock, the ASIC hardware will
+ * set the timing registers automatically when "set feature" command
+ * is issued to the device. However, if the controller clock is 133MHz,
+ * the following tables must be used.
+ */
+static struct pdc2027x_pio_timing {
+ u8 value0, value1, value2;
+} pdc2027x_pio_timing_tbl [] = {
+ { 0xfb, 0x2b, 0xac }, /* PIO mode 0 */
+ { 0x46, 0x29, 0xa4 }, /* PIO mode 1 */
+ { 0x23, 0x26, 0x64 }, /* PIO mode 2 */
+ { 0x27, 0x0d, 0x35 }, /* PIO mode 3, IORDY on, Prefetch off */
+ { 0x23, 0x09, 0x25 }, /* PIO mode 4, IORDY on, Prefetch off */
+};
+
+static struct pdc2027x_mdma_timing {
+ u8 value0, value1;
+} pdc2027x_mdma_timing_tbl [] = {
+ { 0xdf, 0x5f }, /* MDMA mode 0 */
+ { 0x6b, 0x27 }, /* MDMA mode 1 */
+ { 0x69, 0x25 }, /* MDMA mode 2 */
+};
+
+static struct pdc2027x_udma_timing {
+ u8 value0, value1, value2;
+} pdc2027x_udma_timing_tbl [] = {
+ { 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */
+ { 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */
+ { 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */
+ { 0x1a, 0x05, 0xcd }, /* UDMA mode 3 */
+ { 0x1a, 0x03, 0xcd }, /* UDMA mode 4 */
+ { 0x1a, 0x02, 0xcb }, /* UDMA mode 5 */
+ { 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */
+};
+
+static struct pci_device_id pdc2027x_pci_tbl[] = {
+#ifdef ATA_ENABLE_PATA
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20268, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 },
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20269, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20270, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_100 },
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20271, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20275, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20276, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+ { PCI_VENDOR_ID_PROMISE, PCI_DEVICE_ID_PROMISE_20277, PCI_ANY_ID, PCI_ANY_ID, 0, 0, PDC_UDMA_133 },
+#endif
+ { } /* terminate list */
+};
+
+static struct pci_driver pdc2027x_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = pdc2027x_pci_tbl,
+ .probe = pdc2027x_init_one,
+ .remove = __devexit_p(pdc2027x_remove_one),
+};
+
+static Scsi_Host_Template pdc2027x_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .queuecommand = ata_scsi_queuecmd,
+ .eh_strategy_handler = ata_scsi_error,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+};
+
+static struct ata_port_operations pdc2027x_pata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = pdc2027x_set_piomode,
+ .set_dmamode = pdc2027x_set_dmamode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .phy_reset = pdc2027x_phy_reset,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+};
+
+static struct ata_port_info pdc2027x_port_info[] = {
+ /* PDC_UDMA_100 */
+ {
+ .sht = &pdc2027x_sht,
+ .host_flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
+ ATA_FLAG_SRST,
+ .pio_mask = 0x03, /* pio3-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &pdc2027x_pata_ops,
+ },
+ /* PDC_UDMA_133 */
+ {
+ .sht = &pdc2027x_sht,
+ .host_flags = ATA_FLAG_NO_LEGACY | ATA_FLAG_SLAVE_POSS |
+ ATA_FLAG_SRST,
+ .pio_mask = 0x03, /* pio3-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &pdc2027x_pata_ops,
+ },
+};
+
+MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Albert Lee");
+MODULE_DESCRIPTION("libata driver module for Promise PDC20268 to PDC20277");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, pdc2027x_pci_tbl);
+
+/**
+ * pdc_get_indexed_reg - Set pdc202xx extended register
+ * @ap: Port to which the extended register is set
+ * @index: index of the extended register
+ */
+static u8 pdc_get_indexed_reg(struct ata_port *ap, u8 index)
+{
+ u8 tmp8;
+
+ outb(index, ap->ioaddr.bmdma_addr + 1);
+ tmp8 = inb(ap->ioaddr.bmdma_addr + 3);
+
+ PDPRINTK("Get index reg%X[%X] \n", index, tmp8);
+ return tmp8;
+}
+/**
+ * pdc_set_indexed_reg - Read pdc202xx extended register
+ * @ap: Port to which the extended register is read
+ * @index: index of the extended register
+ */
+static void pdc_set_indexed_reg(struct ata_port *ap, u8 index, u8 value)
+{
+ outb(index, ap->ioaddr.bmdma_addr + 1);
+ outb(value, ap->ioaddr.bmdma_addr + 3);
+ PDPRINTK("Set index reg%X[%X] \n", index, value);
+}
+/**
+ * pdc2027x_pata_cbl_detect - Probe host controller cable detect info
+ * @ap: Port for which cable detect info is desired
+ *
+ * Read 80c cable indicator from Promise extended register.
+ * This register is latched when the system is reset.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void pdc2027x_cbl_detect(struct ata_port *ap)
+{
+ u8 cbl40c;
+
+ /* check cable detect results */
+ cbl40c = pdc_get_indexed_reg(ap, 0x0b) & 0x04;
+
+ if (cbl40c)
+ goto cbl40;
+
+ PDPRINTK("No cable or 80-conductor cable on port %d\n", ap->port_no);
+
+ ap->cbl = ATA_CBL_PATA80;
+ return;
+
+cbl40:
+ printk(KERN_INFO DRV_NAME ": 40-conductor cable detected on port %d\n", ap->port_no);
+ ap->cbl = ATA_CBL_PATA40;
+ ap->udma_mask &= ATA_UDMA_MASK_40C;
+}
+/**
+ * pdc2027x_port_enabled - Check extended register at 0x04 to see whether the port is enabled.
+ * @ap: Port to check
+ */
+static inline int pdc2027x_port_enabled(struct ata_port *ap)
+{
+ return pdc_get_indexed_reg(ap, 0x04) & 0x02;
+}
+/**
+ * pdc2027x_phy_reset - Probe specified port on PATA host controller
+ * @ap: Port to probe
+ *
+ * Probe PATA phy.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void pdc2027x_phy_reset(struct ata_port *ap)
+{
+ /* Check whether port enabled */
+ if (!pdc2027x_port_enabled(ap)) {
+ ata_port_disable(ap);
+ printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+ return;
+ }
+
+ pdc2027x_cbl_detect(ap);
+ ata_port_probe(ap);
+ ata_bus_reset(ap);
+}
+/**
+ * pdc2027x_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port to configure
+ * @adev: um
+ * @pio: PIO mode, 0 - 4
+ *
+ * Set PIO mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void pdc2027x_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ unsigned int drive_dn = (ap->port_no ? 2 : 0) + adev->devno;
+ u8 adj = (drive_dn%2) ? 0x08 : 0x00;
+ u8 tmp8;
+
+
+ PDPRINTK("adev->pio_mode[%X]\n", adev->pio_mode);
+
+ /* Sanity check */
+ if(pio > 4) {
+ printk(KERN_ERR DRV_NAME ": Unknown pio mode [%d] ignored\n", pio);
+ return;
+
+ }
+
+ /* Set the PIO timing registers using value table for 133MHz */
+ PDPRINTK("Set pio regs... \n");
+
+ pdc_set_indexed_reg(ap, 0x0c + adj, pdc2027x_pio_timing_tbl[pio].value0);
+ pdc_set_indexed_reg(ap, 0x0d + adj, pdc2027x_pio_timing_tbl[pio].value1);
+ pdc_set_indexed_reg(ap, 0x13 + adj, pdc2027x_pio_timing_tbl[pio].value2);
+
+ PDPRINTK("Set pio regs done\n");
+
+ /*
+ * Check whether the device supports turning off IORDY.
+ * For PIO3 and above, the device must support IORDY and set bit 10
+ */
+ if (adev->id[49] & 0x400) {
+ /* IORDY_EN & PREFETCH_EN */
+ /* Turn on Prefetch */
+ tmp8 = pdc_get_indexed_reg(ap, 0x13 + adj);
+ pdc_set_indexed_reg(ap, 0x13 + adj, tmp8 | 0x03);
+
+ PDPRINTK("Turn on prefetch\n");
+ }
+
+ printk(KERN_INFO DRV_NAME ": Set to pio mode[%u] \n", pio);
+}
+/**
+ * pdc2027x_set_dmamode - Initialize host controller PATA UDMA timings
+ * @ap: Port to configure
+ * @adev: um
+ * @udma: udma mode, XFER_UDMA_0 to XFER_UDMA_6
+ *
+ * Set UDMA mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static void pdc2027x_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int dma_mode = adev->dma_mode;
+ unsigned int drive_dn = (ap->port_no ? 2 : 0) + adev->devno;
+ u8 adj = (drive_dn%2) ? 0x08 : 0x00;
+ u8 tmp8;
+
+ if((dma_mode >= XFER_UDMA_0) &&
+ (dma_mode <= XFER_UDMA_6)) {
+ /* Set the UDMA timing registers with value table for 133MHz */
+ unsigned int udma_mode = dma_mode & 0x07;
+
+ if (dma_mode == XFER_UDMA_2) {
+ /*
+ * Turn off tHOLD.
+ * If tHOLD is '1', the hardware will add half clock for data hold time.
+ * This code segment seems to be no effect. tHOLD will be overwritten below.
+ */
+ tmp8 = pdc_get_indexed_reg(ap, 0x10 + adj);
+ pdc_set_indexed_reg(ap, 0x10 + adj, tmp8 & 0x7f);
+ }
+
+ PDPRINTK("Set udma regs... \n");
+ pdc_set_indexed_reg(ap, 0x10 + adj, pdc2027x_udma_timing_tbl[udma_mode].value0);
+ pdc_set_indexed_reg(ap, 0x11 + adj, pdc2027x_udma_timing_tbl[udma_mode].value1);
+ pdc_set_indexed_reg(ap, 0x12 + adj, pdc2027x_udma_timing_tbl[udma_mode].value2);
+ PDPRINTK("Set udma regs done\n");
+
+ printk(KERN_INFO DRV_NAME ": Set to udma mode[%u] \n", udma_mode);
+
+ } else if((dma_mode >= XFER_MW_DMA_0) &&
+ (dma_mode <= XFER_MW_DMA_2)) {
+ /* Set the MDMA timing registers with value table for 133MHz */
+ unsigned int mdma_mode = dma_mode & 0x07;
+
+ PDPRINTK("Set mdma regs... \n");
+ pdc_set_indexed_reg(ap, 0x0e + adj, pdc2027x_mdma_timing_tbl[mdma_mode].value0);
+ pdc_set_indexed_reg(ap, 0x0f + adj, pdc2027x_mdma_timing_tbl[mdma_mode].value1);
+ PDPRINTK("Set mdma regs done\n");
+
+ printk(KERN_INFO DRV_NAME ": Set to mdma mode[%u] \n", mdma_mode);
+ } else {
+ printk(KERN_ERR DRV_NAME ": Unknown dma mode [%u] ignored\n", dma_mode);
+ }
+}
+/**
+ * adjust_pll - Adjust the PLL input clock in Hz.
+ *
+ * @pdc_controller: controller specific information
+ * @probe_ent: For the port address
+ * @pll_clock: The input of PLL in HZ
+ */
+static void pdc_adjust_pll(struct ata_probe_ent *probe_ent, long pll_clock, unsigned int board_idx)
+{
+
+ u8 pll_ctl0, pll_ctl1;
+ long pll_clock_khz = pll_clock / 1000;
+ long pout_required = board_idx? PDC_133_MHZ:PDC_100_MHZ;
+ long ratio = pout_required / pll_clock_khz;
+ int F, R;
+
+
+ /* Sanity check */
+ if (unlikely(pll_clock_khz < 5000L || pll_clock_khz > 70000L)) {
+ printk(KERN_ERR DRV_NAME ": Invalid PLL input clock %ldkHz, give up!\n", pll_clock_khz);
+ return;
+ }
+
+#ifdef PDC_DEBUG
+ PDPRINTK("pout_required is %ld\n", pout_required);
+
+ /* Show the current clock value of PLL control register
+ * (maybe already configured by the firmware)
+ */
+ outb(0x02, probe_ent->port[1].bmdma_addr + 0x01);
+ pll_ctl0 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+ outb(0x03, probe_ent->port[1].bmdma_addr + 0x01);
+ pll_ctl1 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+
+ PDPRINTK("pll_ctl[%X][%X]\n", pll_ctl0, pll_ctl1);
+#endif
+
+ /*
+ * Calculate the ratio of F, R and OD
+ * POUT = (F + 2) / (( R + 2) * NO)
+ */
+ if (ratio < 8600L) { // 8.6x
+ /* Using NO = 0x01, R = 0x0D */
+ R = 0x0d;
+ } else if (ratio < 12900L) { // 12.9x
+ /* Using NO = 0x01, R = 0x08 */
+ R = 0x08;
+ } else if (ratio < 16100L) { // 16.1x
+ /* Using NO = 0x01, R = 0x06 */
+ R = 0x06;
+ } else if (ratio < 64000L) { // 64x
+ R = 0x00;
+ } else {
+ /* Invalid ratio */
+ printk(KERN_ERR DRV_NAME ": Invalid ratio %ld, give up!\n", ratio);
+ return;
+ }
+
+ F = (ratio * (R+2)) / 1000 - 2;
+
+ if (unlikely(F < 0 || F > 127)) {
+ /* Invalid F */
+ printk(KERN_ERR DRV_NAME ": F[%d] invalid!\n", F);
+ return;
+ }
+
+ PDPRINTK("F[%d] R[%d] ratio*1000[%ld]\n", F, R, ratio);
+
+ pll_ctl0 = (u8) F;
+ pll_ctl1 = (u8) R;
+
+ PDPRINTK("Writing pll_ctl[%X][%X]\n", pll_ctl0, pll_ctl1);
+
+ outb(0x02, probe_ent->port[1].bmdma_addr + 0x01);
+ outb(pll_ctl0, probe_ent->port[1].bmdma_addr + 0x03);
+ outb(0x03, probe_ent->port[1].bmdma_addr + 0x01);
+ outb(pll_ctl1, probe_ent->port[1].bmdma_addr + 0x03);
+
+ /* Wait the PLL circuit to be stable */
+ mdelay(30);
+
+#ifdef PDC_DEBUG
+ /*
+ * Show the current clock value of PLL control register
+ * (maybe configured by the firmware)
+ */
+ outb(0x02, probe_ent->port[1].bmdma_addr + 0x01);
+ pll_ctl0 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+ outb(0x03, probe_ent->port[1].bmdma_addr + 0x01);
+ pll_ctl1 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+
+ PDPRINTK("pll_ctl[%X][%X]\n", pll_ctl0, pll_ctl1);
+#endif
+
+ return;
+}
+/**
+ * detect_pll_input_clock - Detect the PLL input clock in Hz.
+ * @probe_ent: for the port address
+ * Ex. 16949000 on 33MHz PCI bus for pdc20275.
+ * Half of the PCI clock.
+ */
+static long pdc_detect_pll_input_clock(struct ata_probe_ent *probe_ent)
+{
+ u8 scr1;
+ unsigned long ctr0;
+ unsigned long ctr1;
+ unsigned long ctr2 = 0;
+ unsigned long ctr3 = 0;
+
+ unsigned long start_count, end_count;
+ long pll_clock;
+
+ /* Read current counter value */
+ outb(0x20, probe_ent->port[0].bmdma_addr + 0x01);
+ ctr0 = inb(probe_ent->port[0].bmdma_addr + 0x03);
+ outb(0x21, probe_ent->port[0].bmdma_addr + 0x01);
+ ctr1 = inb(probe_ent->port[0].bmdma_addr + 0x03);
+
+ outb(0x20, probe_ent->port[1].bmdma_addr + 0x01);
+ ctr2 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+ outb(0x21, probe_ent->port[1].bmdma_addr + 0x01);
+ ctr3 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+
+ start_count = (ctr3 << 23 ) | (ctr2 << 15) | (ctr1 << 8) | ctr0;
+
+ PDPRINTK("ctr0[%lX] ctr1[%lX] ctr2 [%lX] ctr3 [%lX]\n", ctr0, ctr1, ctr2, ctr3);
+
+ /* Start the test mode */
+ outb(0x01, probe_ent->port[0].bmdma_addr + 0x01);
+ scr1 = inb(probe_ent->port[0].bmdma_addr + 0x03);
+ PDPRINTK("scr1[%X]\n", scr1);
+ outb(scr1 | 0x40, probe_ent->port[0].bmdma_addr + 0x03);
+
+ /* Let the counter run for 1000 us. */
+ udelay(1000);
+
+ /* Read the counter values again */
+ outb(0x20, probe_ent->port[0].bmdma_addr + 0x01);
+ ctr0 = inb(probe_ent->port[0].bmdma_addr + 0x03);
+ outb(0x21, probe_ent->port[0].bmdma_addr + 0x01);
+ ctr1 = inb(probe_ent->port[0].bmdma_addr + 0x03);
+
+ outb(0x20, probe_ent->port[1].bmdma_addr + 0x01);
+ ctr2 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+ outb(0x21, probe_ent->port[1].bmdma_addr + 0x01);
+ ctr3 = inb(probe_ent->port[1].bmdma_addr + 0x03);
+
+ end_count = (ctr3 << 23 ) | (ctr2 << 15) | (ctr1 << 8) | ctr0;
+
+ PDPRINTK("ctr0[%lX] ctr1[%lX] ctr2 [%lX] ctr3 [%lX]\n", ctr0, ctr1, ctr2, ctr3);
+
+ /* Stop the test mode */
+ outb(0x01, probe_ent->port[0].bmdma_addr + 0x01);
+ scr1 = inb(probe_ent->port[0].bmdma_addr + 0x03);
+ PDPRINTK("scr1[%X]\n", scr1);
+ outb(scr1 & 0xBF, probe_ent->port[0].bmdma_addr + 0x03);
+
+ /* calculate the input clock in Hz */
+ pll_clock = (long) ((start_count - end_count) * 1000);
+
+ PDPRINTK("start[%lu] end[%lu] \n", start_count, end_count);
+ PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock);
+
+ return pll_clock;
+}
+/**
+ * pdc_hardware_init - Initialize the hardware.
+ * @pdev: instance of pci_dev found
+ * @pdc_controller: controller specific information
+ * @pe: for the port address
+ */
+static int pdc_hardware_init(struct pci_dev *pdev, struct ata_probe_ent *pe, unsigned int board_idx)
+{
+ long pll_clock;
+
+ /*
+ * Detect PLL input clock rate.
+ * On some system, where PCI bus is running at non-standard clock rate.
+ * Ex. 25MHz or 40MHz, we have to adjust the cycle_time.
+ * The pdc20275 controller employs PLL circuit to help correct timing registers setting.
+ */
+ pll_clock = pdc_detect_pll_input_clock(pe);
+
+ if(pll_clock < 0) /* counter overflow? Try again. */
+ pll_clock = pdc_detect_pll_input_clock(pe);
+
+ printk(KERN_INFO DRV_NAME ": PLL input clock %ld kHz\n", pll_clock/1000);
+
+ /* Adjust PLL control register */
+ pdc_adjust_pll(pe, pll_clock, board_idx);
+
+ return 0;
+}
+/**
+ * pdc2027x_init_one - PCI probe function
+ * Called when an instance of PCI adapter is inserted.
+ * This function checks whether the hardware is supported,
+ * initialize hardware and register an instance of ata_host_set to
+ * libata by providing struct ata_probe_ent and ata_device_add().
+ * (implements struct pci_driver.probe() )
+ *
+ * @pdev: instance of pci_dev found
+ * @ent: matching entry in the id_tbl[]
+ */
+static int __devinit pdc2027x_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ unsigned int board_idx = (unsigned int) ent->driver_data;
+
+ struct ata_probe_ent *probe_ent = NULL;
+ int rc;
+
+ if (!printed_version++)
+ printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+
+ rc = pci_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ rc = pci_request_regions(pdev, DRV_NAME);
+ if (rc)
+ goto err_out;
+
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ goto err_out_regions;
+
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ goto err_out_regions;
+
+ /* Prepare the probe entry */
+ probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+ if (probe_ent == NULL) {
+ rc = -ENOMEM;
+ goto err_out_regions;
+ }
+
+ memset(probe_ent, 0, sizeof(*probe_ent));
+ probe_ent->pdev = pdev;
+ INIT_LIST_HEAD(&probe_ent->node);
+
+ probe_ent->sht = pdc2027x_port_info[board_idx].sht;
+ probe_ent->host_flags = pdc2027x_port_info[board_idx].host_flags;
+ probe_ent->pio_mask = pdc2027x_port_info[board_idx].pio_mask;
+ probe_ent->udma_mask = pdc2027x_port_info[board_idx].udma_mask;
+ probe_ent->port_ops = pdc2027x_port_info[board_idx].port_ops;
+
+ probe_ent->irq = pdev->irq;
+ probe_ent->irq_flags = SA_SHIRQ;
+
+ probe_ent->port[0].cmd_addr = pci_resource_start(pdev, 0);
+ ata_std_ports(&probe_ent->port[0]);
+ probe_ent->port[0].altstatus_addr =
+ probe_ent->port[0].ctl_addr =
+ pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS;
+ probe_ent->port[0].bmdma_addr = pci_resource_start(pdev, 4);
+
+ probe_ent->port[1].cmd_addr = pci_resource_start(pdev, 2);
+ ata_std_ports(&probe_ent->port[1]);
+ probe_ent->port[1].altstatus_addr =
+ probe_ent->port[1].ctl_addr =
+ pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS;
+ probe_ent->port[1].bmdma_addr = pci_resource_start(pdev, 4) + 8;
+
+ probe_ent->n_ports = 2;
+
+ pci_set_master(pdev);
+ //pci_enable_intx(pdev);
+
+ /* initialize adapter */
+ if(pdc_hardware_init(pdev, probe_ent, board_idx) != 0)
+ goto err_out_free_ent;
+
+ ata_device_add(probe_ent);
+ kfree(probe_ent);
+
+ return 0;
+
+err_out_free_ent:
+ kfree(probe_ent);
+err_out_regions:
+ pci_release_regions(pdev);
+err_out:
+ pci_disable_device(pdev);
+ return rc;
+}
+/**
+ * pdc2027x_remove_one - Called to remove a single instance of the
+ * adapter.
+ *
+ * @dev: The PCI device to remove.
+ * FIXME: module load/unload not working yet
+ */
+static void __devexit pdc2027x_remove_one(struct pci_dev *pdev)
+{
+ ata_pci_remove_one(pdev);
+}
+/**
+ * pdc2027x_init - Called after this module is loaded into the kernel.
+ */
+static int __init pdc2027x_init(void)
+{
+ return pci_module_init(&pdc2027x_pci_driver);
+}
+/**
+ * pdc2027x_exit - Called before this module unloaded from the kernel
+ */
+static void __exit pdc2027x_exit(void)
+{
+ pci_unregister_driver(&pdc2027x_pci_driver);
+}
+
+module_init(pdc2027x_init);
+module_exit(pdc2027x_exit);
diff -Nru linux-2.6.9-ori/include/linux/libata.h linux-2.6.9-mod/include/linux/libata.h
--- linux-2.6.9-ori/include/linux/libata.h 2004-10-19 05:53:07.000000000 +0800
+++ linux-2.6.9-mod/include/linux/libata.h 2004-10-21 11:33:34.000000000 +0800
@@ -37,7 +37,7 @@
#undef ATA_IRQ_TRAP /* define to ack screaming irqs */
#undef ATA_NDEBUG /* define to disable quick runtime checks */
#undef ATA_ENABLE_ATAPI /* define to enable ATAPI support */
-#undef ATA_ENABLE_PATA /* define to enable PATA support in some
+#define ATA_ENABLE_PATA /* define to enable PATA support in some
* low-level drivers */
#undef ATAPI_ENABLE_DMADIR /* enables ATAPI DMADIR bridge support */
^ permalink raw reply [flat|nested] 17+ messages in thread